summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/alcor.c
AgeCommit message (Collapse)Author
2019-05-07Merge tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds
Pull MMC updates from Ulf Hansson: "MMC core: - Fix a few memoryleaks - Minor improvements to the card initialization sequence - Partially support sleepy GPIO controllers for pwrseq eMMC MMC host: - alcor: Work with multiple-entry sglists - alcor: Enable DMA for writes - meson-gx: Improve tuning support - meson-gx: Avoid clock glitch when switching to DDR modes - meson-gx: Disable unreliable HS400 mode - mmci: Minor updates for support of HW busy detection - mmci: Support data transfers for the stm32_sdmmc variant - mmci: Restructure code to better support different variants - mtk-sd: Add support for version found on MT7620 family SOCs - mtk-sd: Add support for the MT8516 version - mtk-sd: Add Chaotian Jing as the maintainer - sdhci: Reorganize request-code to convert from tasklet to workqueue - sdhci_am654: Stabilize support for lower speed modes - sdhci-esdhc-imx: Add HS400 support for iMX7ULP - sdhci-esdhc-imx: Add support for iMX7ULP version - sdhci-of-arasan: Allow to disable DCMDs via DT for CQE - sdhci-of-esdhc: Add support for the ls1028a version - sdhci-of-esdhc: Several fixups for errata - sdhci-pci: Fix BYT OCP setting - sdhci-pci: Add support for Intel CML - sdhci-tegra: Add support for system suspend/resume - sdhci-tegra: Add CQE support for Tegra186 WAR - sdhci-tegra: Add support for Tegra194 - sdhci-tegra: Update HW tuning process MEMSTICK: - I volunteered to help as a maintainer for the memstick subsystem, which is reflected by an update to the MAINTAINERS file. Changes are funneled through my MMC git and we will use the linux-mmc mailing list. MEMSTICK host: - A few minor cleanups" * tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (87 commits) mmc: sdhci-pci: Fix BYT OCP setting dt-bindings: mmc: add DT bindings for ls1028a eSDHC host controller mmc: alcor: Drop pointer to mmc_host from alcor_sdmmc_host mmc: mtk-sd: select REGULATOR mmc: mtk-sd: enable internal card-detect logic. mmc: mtk-sd: add support for config found in mt7620 family SOCs. mmc: mtk-sd: don't hard-code interrupt trigger type mmc: core: Fix tag set memory leak dt-bindings: mmc: Add support for MT8516 to mtk-sd mmc: mmci: Prevent polling for busy detection in IRQ context mmc: mmci: Cleanup mmci_cmd_irq() for busy detect mmc: usdhi6rol0: mark expected switch fall-throughs mmc: core: Verify SD bus width mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidle dt-bindings: mmc: fsl-imx-esdhc: add imx7ulp compatible string mmc: meson-gx: add signal resampling tuning mmc: meson-gx: remove Rx phase tuning mmc: meson-gx: avoid clock glitch when switching to DDR modes mmc: meson-gx: disable HS400 ...
2019-05-06Merge tag 'arm64-mmiowb' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull mmiowb removal from Will Deacon: "Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb()) Remove mmiowb() from the kernel memory barrier API and instead, for architectures that need it, hide the barrier inside spin_unlock() when MMIO has been performed inside the critical section. The only relatively recent changes have been addressing review comments on the documentation, which is in a much better shape thanks to the efforts of Ben and Ingo. I was initially planning to split this into two pull requests so that you could run the coccinelle script yourself, however it's been plain sailing in linux-next so I've just included the whole lot here to keep things simple" * tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits) docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section arch: Remove dummy mmiowb() definitions from arch code net/ethernet/silan/sc92031: Remove stale comment about mmiowb() i40iw: Redefine i40iw_mmiowb() to do nothing scsi/qla1280: Remove stale comment about mmiowb() drivers: Remove explicit invocations of mmiowb() drivers: Remove useless trailing comments from mmiowb() invocations Documentation: Kill all references to mmiowb() riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() m68k/io: Remove useless definition of mmiowb() nds32/io: Remove useless definition of mmiowb() x86/io: Remove useless definition of mmiowb() arm64/io: Remove useless definition of mmiowb() ARM/io: Remove useless definition of mmiowb() mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors ...
2019-05-06mmc: alcor: Drop pointer to mmc_host from alcor_sdmmc_hostKamlesh Gurudasani
The driver for Alcor Micro AU6601 and AU6621 controllers uses a pointer to get from the private alcor_sdmmc_host structure to the generic mmc_host structure. However the latter is always immediately preceding the former in memory, so compute its address with a subtraction (which is cheaper than a dereference) and drop the superfluous pointer. No functional change intended. Signed-off-by: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-05-06mmc: alcor: work with multiple-entry sglistsDaniel Drake
DMA on this hardware is limited to dealing with a 4096 bytes at a time. Previously, the driver was set up accordingly to request single-page DMA buffers, however that had the effect of generating a large number of small MMC requests for data I/O. Improve the driver to accept multi-entry scatter-gather lists. The size of each entry is already capped to 4096 bytes (AU6601_MAX_DMA_BLOCK_SIZE), matching the hardware requirements. Existing driver code already iterates through remaining sglist entries after each DMA transfer is complete. Also add some comments to help clarify the situation, and clear up some of the confusion I had regarding DMA vs PIO. Testing with dd, this increases write performance from 2mb/sec to 10mb/sec, and increases read performance from 4mb/sec to 14mb/sec. Signed-off-by: Daniel Drake <drake@endlessm.com> Link: http://lkml.kernel.org/r/CAD8Lp47JYdZzbV9F+asNwvSfLF_po_J7ir6R_Vb-Dab21_=Krw@mail.gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-05-06Revert "mmc: alcor: enable DMA transfer of large buffers"Daniel Drake
This reverts commit 57ebb96c293da9f0ec56aba13c5541269a5c10b1. Usage of the DMA page iterator was problematic here because we were not considering offset & length of entries in the scatterlist. Also, after further discussion, the suggested revised approach is much more similar to the driver implementation before this commit was applied, so revert it. Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-04-15mmc: alcor: enable DMA transfer of large buffersDaniel Drake
DMA on this hardware is limited to dealing with a single page at a time. Previously, the driver was set up accordingly to request single-page DMA buffers, however that had the effect of generating a large number of small MMC requests for data I/O. Improve the driver to accept scatter-gather DMA buffers of larger sizes. Iterate through those buffers a page at a time. Testing with dd, this increases write performance from 2mb/sec to 10mb/sec, and increases read performance from 4mb/sec to 14mb/sec. Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-04-15mmc: alcor: enable DMA for writesDaniel Drake
Enable the DMA codepath for writes as well as reads. This improves write speed from 1mb/sec to 2mb/sec (tested with dd). The original ampe_stor vendor driver also uses DMA for writes. Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-04-08drivers: Remove explicit invocations of mmiowb()Will Deacon
mmiowb() is now implied by spin_unlock() on architectures that require it, so there is no reason to call it from driver code. This patch was generated using coccinelle: @mmiowb@ @@ - mmiowb(); and invoked as: $ for d in drivers include/linux/qed sound; do \ spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done NOTE: mmiowb() has only ever guaranteed ordering in conjunction with spin_unlock(). However, pairing each mmiowb() removal in this patch with the corresponding call to spin_unlock() is not at all trivial, so there is a small chance that this change may regress any drivers incorrectly relying on mmiowb() to order MMIO writes between CPUs using lock-free synchronisation. If you've ended up bisecting to this commit, you can reintroduce the mmiowb() calls using wmb() instead, which should restore the old behaviour on all architectures other than some esoteric ia64 systems. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-03-28mmc: alcor: don't write data before command has completedDaniel Drake
The alcor driver is setting up data transfer and submitting the associated MMC command at the same time. While this works most of the time, it occasionally causes problems upon write. In the working case, after setting up the data transfer and submitting the MMC command, an interrupt comes in a moment later with CMD_END and WRITE_BUF_RDY bits set. The data transfer then happens without problem. However, on occasion, the interrupt that arrives at that point only has WRITE_BUF_RDY set. The hardware notifies that it's ready to write data, but the associated MMC command is still running. Regardless, the driver was proceeding to write data immediately, and that would then cause another interrupt indicating data CRC error, and the write would fail. Additionally, the transfer setup function alcor_trigger_data_transfer() was being called 3 times for each write operation, which was confusing and may be contributing to this issue. Solve this by tweaking the driver behaviour to follow the sequence observed in the original ampe_stor vendor driver: 1. When starting request handling, write 0 to DATA_XFER_CTRL 2. Submit the command 3. Wait for CMD_END interrupt and then trigger data transfer 4. For the PIO case, trigger the next step of the data transfer only upon the following DATA_END interrupt, which occurs after the block has been written. I confirmed that the read path still works (DMA & PIO) and also now presents more consistency with the operations performed by ampe_stor. Signed-off-by: Daniel Drake <drake@endlessm.com> Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-21mmc: alcor: fix DMA readsDaniel Drake
Setting max_blk_count to 1 here was causing the mmc block layer to always use the MMC_READ_SINGLE_BLOCK command here, which the driver does not DMA-accelerate. Drop the max_blk_ settings here. The mmc host defaults suffice, along with the max_segs and max_seg_size settings, which I have now documented in more detail. Now each MMC command reads 4 512-byte blocks, using DMA instead of PIO. On my SD card, this increases read performance (measured with dd) from 167kb/sec to 4.6mb/sec. Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com Signed-off-by: Daniel Drake <drake@endlessm.com> Reviewed-by: Oleksij Rempel <linux@rempel-privat.de> Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17mmc: alcor: remove set but not used variables 'len, clock_out'YueHaibing
Fixes gcc '-Wunused-but-set-variable' warning: drivers/mmc/host/alcor.c: In function 'alcor_data_set_dma': drivers/mmc/host/alcor.c:124:12: warning: variable 'len' set but not used [-Wunused-but-set-variable] drivers/mmc/host/alcor.c:648:15: warning: variable 'clock_out' set but not used [-Wunused-but-set-variable] Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17mmc: add new Alcor Micro Cardreader SD/MMC driverOleksij Rempel
This driver provides support for Alcor Micro AU6601 and AU6621 SD/MMC controller. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>