| Age | Commit message (Collapse) | Author |
|---|
|
Merge in late fixes to prepare for the 6.12 net-next PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After calling m_can_stop() an interrupt may be pending or NAPI might
still be executed. This means the driver might still touch registers
of the IP core after the clocks have been disabled. This is not good
practice and might lead to aborts depending on the SoC integration.
To avoid these potential problems, make m_can_close() symmetric to
m_can_open(), i.e. stop the clocks at the end, right before shutting
down the transceiver.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If an interrupt (RX-complete or error flag) is set when bringing up
the CAN device, e.g. due to CAN bus traffic before initializing the
device, when m_can_start() is called and interrupts are enabled,
m_can_isr() is called immediately, which disables all CAN interrupts
and calls napi_schedule().
Because napi_enable() isn't called until later in m_can_open(), the
call to napi_schedule() never schedules the m_can_poll() callback and
the device is left with interrupts disabled and can't receive any CAN
packets until rebooted.
This can be verified by running "cansend" from another device before
setting the bitrate and calling "ip link set up can0" on the test
device. Adding debug lines to m_can_isr() shows it's called with flags
(IR_EP | IR_EW | IR_CRCE), which calls m_can_disable_all_interrupts()
and napi_schedule(), and then m_can_poll() is never called.
Move the call to napi_enable() above the call to m_can_start() to
enable any initial interrupt flags to be handled by m_can_poll() so
that interrupts are reenabled. Add a call to napi_disable() in the
error handling section of m_can_open(), to handle the case where later
functions return errors.
Also, in m_can_close(), move the call to napi_disable() below the call
to m_can_stop() to ensure all interrupts are handled when bringing
down the device. This race condition is much less likely to occur.
Tested on a Microchip SAMA7G54 MPU. The fix should be applicable to
any SoC with a Bosch M_CAN controller.
Signed-off-by: Jake Hamby <Jake.Hamby@Teledyne.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-1-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enabling 64-bit addressing for DMA buffers will prevent issues
on some memory constrained platforms like e.g. Raspberry Pi 5,
where the driver won't load because it cannot allocate enough
continuous memory in the default 32-bit memory address range.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://patch.msgid.link/d7340f78e3db305bfeeb8229d2dd1c9077e10b92.1725875278.git.martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Remove the CAN_CTRLMODE_3_SAMPLES announcement for CAN-USB/3-FD devices
because these devices don't support it.
The hardware has a Microchip SAM E70 microcontroller that uses a Bosch
MCAN IP core as CAN FD controller. But this MCAN core doesn't support
triple sampling.
Fixes: 80662d943075 ("can: esd_usb: Add support for esd CAN-USB/3")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240904222740.2985864-2-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
error code register
Probably due to a copy/paste error rkcanfd_handle_error_int_reg_ec()
checks twice if the RKCANFD_REG_ERROR_CODE_TX_ACK_EOF bit is set in
reg_ec.
Keep the correct check for RKCANFD_REG_ERROR_CODE_TX_ACK_EOF and
remove the superfluous one.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://patch.msgid.link/9a46d10d-e4e3-40a5-8fb6-f4637959f124@stanley.mountain
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Link: https://patch.msgid.link/20240911-can-rockchip_canfd-fixes-v1-2-5ce385b5ab10@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Rework the delay calculation to only require a single 64-bit division.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[mkl: port to on-top of existing 32-bit division fix]
Link: https://patch.msgid.link/20240911-can-rockchip_canfd-fixes-v1-1-5ce385b5ab10@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On the Microchip SAMA7G54 MPU the IR_TSW (timestamp wraparound) fires
at about 1 Hz, but the driver doesn't care about it. Add it to the
list of interrupts to disable in m_can_chip_config to reduce unneeded
wakeups.
Link: https://patch.msgid.link/DM8PR14MB5221D9DD3A7F2130EF161AF7EF9E2@DM8PR14MB5221.namprd14.prod.outlook.com
Signed-off-by: Jake Hamby <Jake.Hamby@Teledyne.com>
Link: https://patch.msgid.link/20240911-can-m_can-mask-timestamp-wraparound-irq-v1-1-0155b70dc827@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN-USB/3-FD was missing on the list of supported devices.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://patch.msgid.link/20240910170236.2287637-1-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all can drivers to use .remove(), with the eventual goal to drop
struct platform_driver::remove_new(). As .remove() and .remove_new() have
the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909072742.381003-2-u.kleine-koenig@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
platforms
On some 32-bit platforms (at least on parisc), the compiler generates
a call to __divdi3() from the u32 by 3 division in
rkcanfd_timestamp_init(), which results in the following linker
error:
| ERROR: modpost: "__divdi3" [drivers/net/can/rockchip/rockchip_canfd.ko] undefined!
As this code doesn't run in the hot path, a 64 bit by 32 bit division
is OK, even on 32 bit platforms. Use an explicit call to div_u64() to
fix linking.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409072304.lCQWyNLU-lkp@intel.com/
Link: https://patch.msgid.link/20240909-can-rockchip_canfd-fix-64-bit-division-v1-1-2748d9422b00@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
drivers/net/can/rockchip/rockchip_canfd-core.c:770:20: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
770 | .ndo_start_xmit = rkcanfd_start_xmit,
| ^~~~~~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int' (although the types are ABI compatible). Adjust
the return type of rkcanfd_start_xmit() to match the prototype's to
resolve the warning.
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20240906-rockchip-canfd-wifpts-v1-1-b1398da865b7@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use of the typed property accessors is preferred over of_get_property().
The existing code doesn't work on little endian systems either. Replace
the of_get_property() calls with of_property_read_bool() and
of_property_read_u32().
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240903135731.405635-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/phy/phy_device.c
2560db6ede1a ("net: phy: Fix missing of_node_put() for leds")
1dce520abd46 ("net: phy: Use for_each_available_child_of_node_scoped()")
https://lore.kernel.org/20240904115823.74333648@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/xilinx/xilinx_axienet.h
drivers/net/ethernet/xilinx/xilinx_axienet_main.c
858430db28a5 ("net: xilinx: axienet: Fix race in axienet_stop")
76abb5d675c4 ("net: xilinx: axienet: Add statistics support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Bus Error Reporting.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-20-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for loopback mode.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-19-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for hardware based timestamping.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-18-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The previous commit prepared the TX path to make use of the full
TX-FIFO depth as much as possible. Increase the available TX-FIFO
depth to the hardware maximum of 2.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-17-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
So far the TX-FIFO is only used with a depth of 1, although the
hardware offers a depth of 2.
The workaround for the chips that are affected by erratum 6, i.e. EFF
frames may be send as standard frames, is to re-send the EFF frame.
This means the driver cannot queue the next frame for sending, as long
ad the EFF frame has not been successfully send out.
Introduce rkcanfd_get_effective_tx_free() that returns "0" space in
the TX-FIFO if an EFF frame is pending and the actual free space in
the TX-FIFO otherwise. Then replace rkcanfd_get_tx_free() with
rkcanfd_get_effective_tx_free() everywhere.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-16-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver contains workarounds for some of the rk3568v2 errata. Add
ethtool-based statistics ("ethtool -S") to track how often an erratum
workaround was needed.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-15-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
broken {RX,TX}ERRORCNT register
Tests show that sometimes both CAN bus error counters read 0x0, even
if the controller is in warning mode
(RKCANFD_REG_STATE_ERROR_WARNING_STATE in RKCANFD_REG_STATE
set).
To work around this issue, if both error counters read from hardware
are 0x0, use the structure priv->bec, otherwise save the read value in
priv->bec.
In rkcanfd_handle_rx_int_one() decrement the priv->bec.rxerr for
successfully RX'ed CAN frames.
In rkcanfd_handle_tx_done_one() decrement the priv->bec.txerr for
successfully TX'ed CAN frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-14-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| A dominant bit at the third bit of the intermission may cause a
| transmission error.
|
| When sampling the third bit of the intermission as a dominant bit, if
| tx_req is configured to transmit extended frames at this time, the
| extended frame may be sent to the bus in the format of a standard
| frame. The extended frame will be sent as a standard frame and will not
| result in error frames
Turn on "Interframe Spaceing RX Mode" only during TX to work around
erratum 12, according to rock-chip:
| Spaceing RX Mode = 1, the third Bit between frames cannot receive
| and send, and the fourth Bit begins to receive and send.
|
| Spaceing RX Mode = 0, allowing the third Bit between frames to
| receive and send.
Message-ID: <be72939f-0a9e-0608-dfff-7b0096a26eba@rock-chips.com>
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-13-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| The CAN controller's transmission of extended frames may
| intermittently change into standard frames.
|
| When using the CAN controller to send extended frames, if the
| 'tx_req' is configured as 1 and coincides with the internal
| transmission point, the extended frame will be transmitted onto the
| bus in the format of a standard frame.
To work around Erratum 6, the driver is in self-receiving mode (RXSTX)
and all received CAN frames are passed through rkcanfd_rxstx_filter().
Add a check in rkcanfd_rxstx_filter() whether the received frame
corresponds to the current outgoing frame, but the extended CAN ID has
been mangled to a standard ID. In this case re-send the original CAN
frame.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-12-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The IP core has a TX event FIFO. In other IP cores, this type of FIFO
usually contains the events that a CAN frame has been successfully
sent. However, the IP core on the rk3568v2 the FIFO also holds events
of unsuccessful transmission attempts.
It turned out that the best way to work around this problem is to set
the IP core to self-receive mode (RXSTX), filter out the self-received
frames and insert them into the complete TX path.
Add a pair new functions to check if 2 struct canfd_frame are equal.
The 1st checks if the header of the CAN frames are equal, the 2nd
checks if the data portion are equal:
- rkcanfd_can_frame_header_equal()
- rkcanfd_can_frame_data_equal()
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-11-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Tests on the rk3568v2 and rk3568v3 show that a reduced "baudclk" (e.g.
80MHz, compared to the standard 300MHz) significantly increases the
possibility of incorrect FIFO counters, i.e. erratum 5.
Print an info message if the clock is below the known good value of
300MHz.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-10-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
erratum 5: check for empty FIFO
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| Erratum 5: Counters related to the TXFIFO and RXFIFO exhibit
| abnormal counting behavior.
|
| Due to a bug in the cross-asynchronous logic of the enable signals
| for rx_fifo_cnt and txe_fifo_frame_cnt counters, the counts of these
| two counters become inaccurate. This issue has resulted in the
| inability to use the TXFIFO and RXFIFO functions.
The errata sheet mentioned above states that only the rk3568v2 is
affected by this erratum, but tests with the rk3568v2 and rk3568v3
show that the RX_FIFO_CNT is sometimes too high. This leads to CAN
frames being read from the FIFO, which is then already empty.
Further tests on the rk3568v2 and rk3568v3 show that in this
situation (i.e. empty FIFO) all elements of the FIFO
header (frameinfo, id, ts) contain the same data.
On the rk3568v2 and rk3568v3, this problem only occurs extremely
rarely with the standard clock of 300 MHz, but almost immediately at
80 MHz.
To workaround this problem, check for empty FIFO with
rkcanfd_fifo_header_empty() in rkcanfd_handle_rx_int_one() and exit
early.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-9-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Even the rk3568v3 has some known issues. Document them together with a
reproducer.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-8-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add the support for the rk3568v3 SoC, the CAN-FD IP core has 7
documented errata.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-7-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The errata sheets doesn't say anything about CAN-FD, but tests on the
rk3568v2 and rk3568v3 show that receiving certain CAN-FD frames
triggers an Error Interrupt.
Mark the CAN-FD support as broken.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-6-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add a basic infrastructure for quirks for the 12 documented errata.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-5-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add driver for the Rockchip CAN-FD controller.
The IP core on the rk3568v2 SoC has 12 documented errata. Corrections
for these errata will be added in the upcoming patches.
Since several workarounds are required for the TX path, only add the
base driver that only implements the RX path.
Although the RX path implements CAN-FD support, it's not activated in
ctrlmode_supported, as the IP core in the rk3568v2 has problems with
receiving or sending certain CAN-FD frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-4-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20240901112803.212753-5-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20240901112803.212753-4-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20240901112803.212753-3-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Kvaser's PCIe cards uses the KCAN FPGA IP block which has dual 4K
buffers for incoming messages shared by all (currently up to eight)
channels. While the driver processes messages in one buffer, new
incoming messages are stored in the other and so on.
The design of KCAN is such that a buffer must be fully read and then
released. Releasing a buffer will make the FPGA switch buffers. If the
other buffer contains at least one incoming message the FPGA will also
instantly issue a new interrupt, if not the interrupt will be issued
after receiving the first new message.
With IRQx interrupts, it takes a little time for the interrupt to
happen, enough for any previous ISR call to do it's business and
return, but MSI interrupts are way faster so this time is reduced to
almost nothing.
So with MSI, releasing the buffer HAS to be the very last action of
the ISR before returning, otherwise the new interrupt might be
"masked" by the kernel because the previous ISR call hasn't returned.
And the interrupts are edge-triggered so we cannot loose one, or the
ping-pong reading process will stop.
This is why this patch modifies the driver to use a single write to
the SRB_CMD register before returning.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240830153113.2081440-1-martin.jocic@kvaser.com
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
dev_err_probe() is used to log an error message during the probe process
of a device.
It can simplify the error path and unify a message template.
Using this helper is totally fine even if err is known to never
be -EPROBE_DEFER.
The benefit compared to a normal dev_err() is the standardized format
of the error code, it being emitted symbolically and the fact that
the error code is returned which allows more compact error paths.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Link: https://patch.msgid.link/20240830110651.519119-1-yanzhen@vivo.com
mkl: fix indention
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the IS_ENABLED() macro to check kernel config defines instead of
ifdef. Use upper_32_bits() to avoid warnings about "right shift count
>= width of type" on systems with CONFIG_ARCH_DMA_ADDR_T_64BIT not
set. In kvaser_pciefd_write_dma_map_altera() use lower_32_bits() for
symmetry.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://patch.msgid.link/20240830141038.1402217-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_priv::ctrlmode
This patch moves the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_changelink in front of the evaluation of data[IFLA_CAN_BITTIMING].
This avoids a call to do_set_data_bittiming providing a stale
can_priv::ctrlmode with a CAN_CTRLMODE_FD flag not matching the
requested state when switching between a CAN Classic and CAN-FD bitrate.
In the same manner the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_validate is also moved in front of the evaluation of
data[IFLA_CAN_BITTIMING].
This is a preparation for patches where the nominal and data bittiming
may have interdependencies on the driver side depending on the
CAN_CTRLMODE_FD flag state.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://patch.msgid.link/20240808164224.213522-1-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The mcp251x_hw_wake() function is called with the mpc_lock mutex held and
disables the interrupt handler so that no interrupts can be processed while
waking the device. If an interrupt has already occurred then waiting for
the interrupt handler to complete will deadlock because it will be trying
to acquire the same mutex.
CPU0 CPU1
---- ----
mcp251x_open()
mutex_lock(&priv->mcp_lock)
request_threaded_irq()
<interrupt>
mcp251x_can_ist()
mutex_lock(&priv->mcp_lock)
mcp251x_hw_wake()
disable_irq() <-- deadlock
Use disable_irq_nosync() instead because the interrupt handler does
everything while holding the mutex so it doesn't matter if it's still
running.
Fixes: 8ce8c0abcba3 ("can: mcp251x: only reset hardware as required")
Signed-off-by: Simon Arlott <simon@octiron.net>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/4fc08687-1d80-43fe-9f0d-8ef8475e75f6@0882a8b5-c6c3-11e9-b005-00805fc181fe.uuid.home.arpa
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When changing the interface from CAN-CC to CAN-FD mode the old
coalescing parameters are re-used. This might cause problem, as the
configured parameters are too big for CAN-FD mode.
During testing an invalid TX coalescing configuration has been seen.
The problem should be been fixed in the previous patch, but add a
safeguard here to ensure that the number of TEF coalescing buffers (if
configured) is exactly the half of all TEF buffers.
Link: https://lore.kernel.org/all/20240805-mcp251xfd-fix-ringconfig-v1-2-72086f0ca5ee@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the ring (rx, tx) and/or coalescing parameters (rx-frames-irq,
tx-frames-irq) have been configured while the interface was in CAN-CC
mode, but the interface is brought up in CAN-FD mode, the ring
parameters might be too big.
Use the default CAN-FD values in this case.
Fixes: 9263c2e92be9 ("can: mcp251xfd: ring: add support for runtime configurable RX/TX ring parameters")
Link: https://lore.kernel.org/all/20240805-mcp251xfd-fix-ringconfig-v1-1-72086f0ca5ee@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The use of coalescing for non-peripheral chips in the current
implementation is limited to non-existing. Disable the possibility to
set coalescing through ethtool.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-8-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
To force writing the enabled interrupts, reset the active_interrupts
cache.
Fixes: 07f25091ca02 ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
active_interrupts is a cache for the enabled interrupts and not the
global masking of interrupts. Do not clear this variable otherwise we
may loose the state of the interrupts.
Fixes: 07f25091ca02 ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On setups without interrupts, the interrupt handler is called from a
timer callback. For non-peripheral receives napi is scheduled,
interrupts are disabled and the timer is canceled with a blocking call.
In case of an error this can happen as well.
Check if napi is scheduled in the timer callback after the interrupt
handler executed. If napi is scheduled, the timer is disabled. It will
be reenabled by m_can_poll().
Return error values from the interrupt handler so that interrupt threads
and timer callback can deal differently with it. In case of the timer
we only disable the timer. The rest will be done when stopping the
interface.
Fixes: b382380c0d2d ("can: m_can: Add hrtimer to generate software interrupt")
Fixes: a163c5761019 ("can: m_can: Start/Cancel polling timer together with interrupts")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
m_can_rx_peripheral() is a wrapper around m_can_rx_handler() that calls
m_can_disable_all_interrupts() on error. The same handling for the same
error path is done in m_can_isr() as well.
So remove m_can_rx_peripheral() and do the call from m_can_isr()
directly.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We don't need to disable coalescing when the interrupt handler executes
while the chip is suspended. The coalescing is already reset during
suspend.
Fixes: 07f25091ca02 ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During resume the interrupts are limited to IR_RF0N and the chip keeps
running. In this case if coalescing is enabled and active we may miss
waterlevel interrupts during suspend. It is safer to reset the
coalescing by stopping the timer and adding IR_RF0N | IR_TEFN to the
interrupts.
This is a theoratical issue and probably extremely rare.
Cc: Martin Hundebøll <martin@geanix.com>
Fixes: 4a94d7e31cf5 ("can: m_can: allow keeping the transceiver running in suspend")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It appears that the irq requested in m_can_open() may be leaked
if an error subsequently occurs: if m_can_start() fails.
Address this by calling free_irq in the unwind path for
such cases.
Flagged by Smatch.
Compile tested only.
Fixes: eaacfeaca7ad ("can: m_can: Call the RAM init directly from m_can_chip_config")
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240805-mcan-irq-v2-1-7154c0484819@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
kvaser_usb_{ethtool,netdev}_ops
Now when we only got one set of ethtool_ops and netdev_ops, remove the
"hwts" suffix from the struct variables
kvaser_usb_{ethtool,netdev}_ops_hwts.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20240701154936.92633-16-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
