| Age | Commit message (Collapse) | Author |
|---|
|
Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ9477 has the 11 bit ageing count value which is split across the two
registers. And LAN937x has the 20 bit ageing count which is also split
into two registers. Each count in the registers represents 1 second.
This patch add the support for ageing time for KSZ9477 and LAN937x
series of switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables the interrupts for internal phy link detection for
LAN937x. The interrupt enable bits are active low. There is global
interrupt mask for each port. And each port has the individual interrupt
mask for TAS. QCI, SGMII, PTP, PHY and ACL.
The first level of interrupt domain is registered for global port
interrupt and second level of interrupt domain for the individual port
interrupts. The phy interrupt is enabled in the lan937x_mdio_register
function. Interrupt from which port is raised will be detected based on
the interrupt host data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY access may end with errors on different levels. So, allow to forward
return values where possible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
