| Age | Commit message (Collapse) | Author |
|---|
|
The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.
On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.
The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
- When emitting a oneshot pulse, instead of being told when to emit it,
the switch just does it "now" and tells you later what time it was,
via the PTPSYNCTS register. [ Incidentally, this is the same register
that the slave uses to collect the ext_ts timestamp from, too. ]
- On the sync slave, there is no interrupt mechanism on reception of a
new extts, and no FIFO to buffer them, because in the foreseen use
case, software is in control of both the master and the slave pins,
so it "knows" when there's something to collect.
These 2 problems mean that:
- We don't support (at least yet) the quirky oneshot mode exposed by
the hardware, just normal periodic output.
- We abuse the hardware a little bit when we expose generic extts.
Because there's no interrupt mechanism, we need to poll at double the
frequency we expect to receive a pulse. Currently that means a
non-configurable "twice a second".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for NXP SJA1105 series Ethernet switch support.
It uses an expilict block comment for the SPDX License
Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support tc-taprio offload, the TTEthernet egress scheduling
core registers must be made visible through the static interface.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the end of the commit 1da73821343c ("net: dsa: sja1105: Add FDB
operations for P/Q/R/S series") message, I said that:
At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
It looks like the reason why they were not visible in 'bridge fdb' was
that they were never learned - always flooded.
SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field:
Specify the maximum number of MAC address dynamically learned from
the respective port. It is used to limit the number of learned MAC
addresses per port.
It looks like not providing a value in the static config (aka providing
zeroes) is enough for it to not store the learned addresses in the FDB.
For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This
may be revisited if the situation calls for that - for now I'm happy
that learning works.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This table is used to program the switch to emit "meta" follow-up
Ethernet frames (which contain partial RX timestamps) after each
link-local frame that was trapped to the CPU port through MAC filtering.
This includes PTP frames.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This appends to the L2 Forwarding and L2 Forwarding Parameters tables
(originally added for first-generation switches) the bits that are new
in the second generation.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
