Age | Commit message (Collapse) | Author |
|
Convert b53 to provide its own phylink MAC operations, thus avoiding the
shim layer in DSA's port.c
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-9-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only use the PHYLINK implementation from there on now that an equivalent
configuration is applied to all of the switch ports.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-8-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
And make sure this is done for the MLO_AN_PHY case, where it actually
makes sense, contrary to b53_adjust_link() which only did it for
fixed-PHY configurations where it does not make sense.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-7-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Call b53_adjust_531x5_rgmii() and b53_adjust_5325_mii() from
b53_phylink_mac_config() when we have a fixed PHY in preparation for removing
b53_adjust_link(). Also move b53_adjust_63xx_rgmii() to
b53_phylink_mac_config() where it logically belongs.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-6-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Just like what b53_adjust_link() does, force flow control for the
BCM5301X CPU port(s) by forcing rx_pause and tx_pause in
b53_phylink_mac_link_up(). Preparatory step for getting rid of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-5-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Takes care of doing the 5325 switch series specific MII programming and
is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-4-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Takes care of doing the 531x5 switch series specific RGMII programming
and is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-3-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
They are not used outside of the b53_common.c file, no need to be
exported.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit f86ad77faf24 ("net: dsa: bcm_sf2: Utilize b53_{enable,
disable}_port"), bcm_sf2.c no longer calls b53_eee_enable_set(), and all
its callers are in b53_common.c.
We also need to move it, because it is called within b53_common.c before
its definition, and we want to avoid forward declarations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240206112527.4132299-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use a separate phylink_mac_ops for the KSZ8830 chip-id.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert ksz_common to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The phylink_mac_config function pointer member of struct ksz_dev_ops is
never initialised, so let's remove it to simplify the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert xrs700x to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide stubs for
the mac_link_down() and mac_config() methods which are mandatory.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert rzn1_a5psw to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide a stub for
the mac_config() method which is mandatory.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert lan9303 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide stubs for
the mac_link_down() and mac_config() methods which are mandatory.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert bcm_sf2 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert lantiq_gswip to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. For lantiq_gswip, it means
we end up with a common instance of phylink MAC operations that are
shared between the different variants, rather than having duplicated
initialisers in dsa_switch_ops.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert qca8k to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert ar9331 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert sja1105 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Convert mv88e6xxx to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Update the Marvell 88e6185 PCS driver to use neg_mode rather than the
mode argument to match the other updated PCS drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
b53_get_mac_eee() sets both eee_enabled and eee_active, and then
returns zero.
dsa_user_get_eee(), which calls this function, will then continue to
call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there
is no PHY present, otherwise calling phy_ethtool_get_eee() which in
turn will call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, dsa_user_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
b53_get_mac_eee() entirely unnecessary.
Remove this code, thus simplifying b53_get_mac_eee().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
This bug was noticed while re-implementing parts of the kernel
driver in userspace using spidev. The goal was to enable some
of the errata workarounds that Microchip describes in their
errata sheet [1].
Both the errata sheet and the regular datasheet of e.g. the KSZ8795
imply that you need to do this for indirect register accesses:
- write a 16-bit value to a control register pair (this value
consists of the indirect register table, and the offset inside
the table)
- either read or write an 8-bit value from the data storage
register (indicated by REG_IND_BYTE in the kernel)
The current implementation has the order swapped. It can be
proven, by reading back some indirect register with known content
(the EEE register modified in ksz8_handle_global_errata() is one of
these), that this implementation does not work.
Private discussion with Oleksij Rempel of Pengutronix has revealed
that the workaround was apparantly never tested on actual hardware.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/Errata/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Tobias Jakobi (Compleo) <tobias.jakobi.compleo@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 7b6e6235b664 ("net: dsa: microchip: ksz8795: handle eee specif erratum")
Link: https://lore.kernel.org/r/20240304154135.161332-1-tobias.jakobi.compleo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the DSA loopback fixed PHY module.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20240208164244.3818498-10-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Not all mv88e6xxx device support C45 read/write operations. Those
which do not return -EOPNOTSUPP. However, when phylib scans the bus,
it considers this fatal, and the probe of the MDIO bus fails, which in
term causes the mv88e6xxx probe as a whole to fail.
When there is no device on the bus for a given address, the pull up
resistor on the data line results in the read returning 0xffff. The
phylib core code understands this when scanning for devices on the
bus. C45 allows multiple devices to be supported at one address, so
phylib will perform a few reads at each address, so although thought
not the most efficient solution, it is a way to avoid fatal
errors. Make use of this as a minimal fix for stable to fix the
probing problems.
Follow up patches will rework how C45 operates to make it similar to
C22 which considers -ENODEV as a none-fatal, and swap mv88e6xxx to
using this.
Cc: stable@vger.kernel.org
Fixes: 743a19e38d02 ("net: dsa: mv88e6xxx: Separate C22 and C45 transactions")
Reported-by: Tim Menninger <tmenninger@purestorage.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129224948.1531452-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When working with GPIO, its direction must be set either when the GPIO is
requested by gpiod_get*() or later on by one of the gpiod_direction_*()
functions. Neither of this is done here which results in undefined
behavior on some systems.
As the reset GPIO is used right after it is requested here, it makes sense
to configure it as GPIOD_OUT_HIGH right away. With that, the following
gpiod_set_value_cansleep(1) becomes redundant and can be safely
removed.
Fixes: a653f2f538f9 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1706266175-3408-1-git-send-email-michal.vokac@ysoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setup PMCR port register for actual speed and duplex on internally
connected PHYs of the MT7988 built-in switch. This fixes links with
speeds other than 1000M.
Fixes: 110c18bfed41 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/a5b04dfa8256d8302f402545a51ac4c626fdba25.1706071272.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240111072018.75971-1-chentao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There used to be a of_node_put(priv->master_mii_dn) call in
bcm_sf2_mdio_unregister(), which was accidentally deleted in commit
6ca80638b90c ("net: dsa: Use conduit and user terms").
But it's not needed - we don't need to hold a reference on the
"brcm,unimac-mdio" OF node for that long, since we don't do anything
with it. We can release it as soon as we finish bcm_sf2_mdio_register().
Also reduce "if (err && dn)" to just "if (err)". We know "dn", aka the
former priv->master_mii_dn, is non-NULL. Otherwise, of_mdio_find_bus(dn)
would not have been able to find the bus behind "brcm,unimac-mdio".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcm_sf2 driver does something strange. Instead of calling
of_mdiobus_register() with an OF node argument, it manually assigns the
bus->dev->of_node and then calls the non-OF mdiobus_register(). This
circumvents some code from __of_mdiobus_register() from running, which
sets the auto-scan mask, parses some device tree properties, etc.
I'm going to go out on a limb and say that the OF node isn't, in fact,
needed at all, and can be removed. The MDIO diversion as initially
implemented in commit 461cd1b03e32 ("net: dsa: bcm_sf2: Register our
slave MDIO bus") looked quite different than it is now, after commit
771089c2a485 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used").
Initially, it made sense, as bcm_sf2 was registering another set of
driver ops for the "brcm,unimac-mdio" OF node. But now, it deletes all
phandles, which makes "phy-handle"s unable to find PHYs, which means
that it always goes through the OF-unaware dsa_user_phy_connect().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accessed either through priv->dev or ds->dev, it is the same device
structure. Keep a single variable which holds a reference to it, and use
it consistently.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__of_mdiobus_register() already calls __mdiobus_register() if the
OF node provided as argument is NULL. We can take advantage of that
and simplify the 2 code path, calling devm_of_mdiobus_register() only
once for both cases.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To simplify reasoning about why the DSA framework provides the
ds->user_mii_bus functionality, drivers should only use it if they
need to. The qca8k driver appears to also use it simply as storage
for a pointer, which is not a good enough reason to make the core
much more difficult to follow.
ds->user_mii_bus is useful for only 2 cases:
1. The driver probes on platform_data (no OF)
2. The driver probes on OF, but there is no OF node for the MDIO bus.
It is unclear if case (1) is supported with qca8k. It might not be:
the driver might crash when of_device_get_match_data() returns NULL
and then it dereferences priv->info without NULL checking.
Anyway, let us limit the ds->user_mii_bus usage only to the above cases,
and not assign it when an OF node is present.
The bus->phy_mask assignment follows along with the movement, because
__of_mdiobus_register() overwrites this bus field anyway. The value set
by the driver only matters for the non-OF code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver calls the non-OF devm_mdiobus_register() rather
than devm_of_mdiobus_register() for this case, but it seems to rather
be a confusing coincidence, and not a real use case that needs to be
supported.
If the device tree says status = "disabled" for the MDIO bus, we
shouldn't need an MDIO bus at all. Instead, just exit as early as
possible and do not call any MDIO API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec38 ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the "lantiq,xrx200-mdio" child has status = "disabled", the MDIO bus
creation should be avoided. Use of_device_is_available() to check for
that, and take advantage of 2 facts:
- of_device_is_available(NULL) returns false
- of_node_put(NULL) is a no-op
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver does not need any of the functionalities that make
ds->user_mii_bus special. Those use cases are listed here:
https://lore.kernel.org/netdev/20231221174746.hylsmr3f7g5byrsi@skbuf/
It just makes use of ds->user_mii_bus only as storage for its own MDIO
bus, which otherwise has no connection to the framework. This is because:
- the gswip driver only probes on OF: it fails if of_device_get_match_data()
returns NULL
- when the child OF node of the MDIO bus is absent, no MDIO bus is
registered at all, not even by the DSA framework. In order for that to
have happened, the gswip driver would have needed to provide
->phy_read() and ->phy_write() in struct dsa_switch_ops, which it does
not.
We can break the connection between the gswip driver and the DSA
framework and still preserve the same functionality.
Since commit 3b73a7b8ec38 ("net: mdio_bus: add refcounting for fwnodes
to mdiobus"), MDIO buses take ownership of the OF node handled to them,
and release it on their own. The gswip driver no longer needs to do
this.
Combine that with devres, and we no longer need to keep track of
anything for teardown purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__of_mdiobus_register(), called right next, overwrites the phy_mask
we just configured on the bus, so this is redundant and confusing.
Delete it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report the applicable subset of an mv88e6xxx port's counters using
ethtool's standardized "rmon" counter group.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chips in this family only have one set of histogram counters, which
can be used to count ingressing and/or egressing traffic. mv88e6xxx
has, up until this point, kept the hardware default of counting both
directions.
In the mean time, standard counter group support has been added to
ethtool. Via that interface, drivers may report ingress-only and
egress-only histograms separately - but not combined.
In order for mv88e6xxx to maximize amount of diagnostic information
that can be exported via standard interfaces, we opt to limit the
histogram counters to ingress traffic only. Which will allow us to
export them via the standard "rmon" group in an upcoming commit.
The reason for choosing ingress-only over egress-only, is to be
compatible with RFC2819 (RMON MIB).
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report the applicable subset of an mv88e6xxx port's counters using
ethtool's standardized "eth-mac" counter group.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the upcoming standard counter group support, we are no longer
reading out the whole set of counters, but rather mapping a subset to
the requested group.
Therefore, create an enum with an ID for each stat, such that
mv88e6xxx_hw_stats[] can be subscripted with a human-readable ID
corresponding to the counter's name.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change contains no functional change. We simply push the hardware
specific stats logic to a function reading a single counter, rather
than the whole set.
This is a preparatory change for the upcoming standard ethtool
statistics support (i.e. "eth-mac", "eth-ctrl" etc.).
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is more consistent with the driver's general structure.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTU callbacks are in layer 1 size, so for example 1500
bytes is a normal setting. Cache this size, and only add
the layer 2 framing right before choosing the setting. On
the CPU port this will however include the DSA tag since
this is transmitted from the parent ethernet interface!
Add the layer 2 overhead such as ethernet and VLAN framing
and FCS before selecting the size in the register.
This will make the code easier to understand.
The rtl8366rb_max_mtu() callback returns a bogus MTU
just subtracting the CPU tag, which is the only thing
we should NOT subtract. Return the correct layer 1
max MTU after removing headers and checksum.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Rename the register name to RTL8366RB instead of the bogus
RTL8368S (internal product name?)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Correct the use of define DSA_TAG_PROTO_LAN937X_VALUE to
DSA_TAG_PROTO_LAN937X to improve readability.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20231206160124.1935451-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|