| Age | Commit message (Collapse) | Author |
|---|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d442 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for flushing the MAC table on a given port in the ocelot
switch library, and use this functionality in the felix DSA driver.
This operation is needed when a port leaves a bridge to become
standalone, and when the learning is disabled, and when the STP state
changes to a state where no FDB entry should be present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simple rename of a variable to make things more logical.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove references to lynx_pcs structures so drivers like the Felix DSA
can reference alternate PCS drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Define more regs. Some switches (e.g. BCM4908) have up to 6 regs.
2. Add helper for handling non-lineral port <-> reg mappings.
3. Add support for 12 B LED reg blocks on BCM4908 (different layout)
Complete support for LEDs setup will be implemented once Linux receives
a proper design & implementation for "hardware" LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211229171642.22942-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
|
|
Add index to flow_action_entry structure and delete index from police and
gate child structure.
We make this change to offload tc action for driver to identify a tc
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c7bd3 ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent net-next fails to initialize ports with:
realtek-smi switch: phy mode gmii is unsupported on port 0
realtek-smi switch lan5 (uninitialized): validation of gmii with
support 0000000,00000000,000062ef and advertisement
0000000,00000000,000062ef failed: -22
realtek-smi switch lan5 (uninitialized): failed to connect to PHY:
-EINVAL
realtek-smi switch lan5 (uninitialized): error -22 setting up PHY
for tree 1, switch 0, port 0
Current net branch(3dd7d40b43663f58d11ee7a3d3798813b26a48f1) is not
affected.
I also noticed the same issue before with older versions but using
a MDIO interface driver, not realtek-smi.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch supports PTP for UDP transport too. Therefore, add the missing static
FDB entries to ensure correct forwarding of these packets.
Fixes: ddd56dfe52c9 ("net: dsa: hellcreek: Add PTP clock support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow PTP peer delay measurements on blocked ports by STP. In case of topology
changes the PTP stack can directly start with the correct delays.
Fixes: ddd56dfe52c9 ("net: dsa: hellcreek: Add PTP clock support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Treat STP as management traffic. STP traffic is designated for the CPU port
only. In addition, STP traffic has to pass blocked ports.
Fixes: e4b27ebc780f ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The insertion of static FDB entries ignores the pass_blocked bit. That bit is
evaluated with regards to STP. Add the missing functionality.
Fixes: e4b27ebc780f ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver was incorrectly converted assuming that "sja1105" is the only
tagger supported by this driver. This results in SJA1110 switches
failing to probe:
sja1105 spi1.0: Unable to connect to tag protocol "sja1110": -EPROTONOSUPPORT
sja1105: probe of spi1.2 failed with error -93
Add DSA_TAG_PROTO_SJA1110 to the list of supported taggers by the
sja1105 driver. The sja1105_tagger_data structure format is common for
the two tagging protocols.
Fixes: c79e84866d2a ("net: dsa: tag_sja1105: convert to tagger-owned data")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings
in mac_config") removed forcing of speed and duplex from
mv88e6xxx_mac_config(), where the link is forced down, and left it only
in mv88e6xxx_mac_link_up(), by which time link is unforced.
It seems that (at least on 88E6190) when changing cmode to 2500base-x,
if the link is not forced down, but the speed or duplex are still
forced, the forcing of new settings for speed & duplex doesn't take in
mv88e6xxx_mac_link_up().
Fix this by unforcing speed & duplex in mv88e6xxx_mac_link_down().
Fixes: 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings in mac_config")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sections
The sja1105 driver messes with the tagging protocol's state when PTP RX
timestamping is enabled/disabled. This is fundamentally necessary
because the tagger needs to know what to do when it receives a PTP
packet. If RX timestamping is enabled, then a metadata follow-up frame
is expected, and this holds the (partial) timestamp. So the tagger plays
hide-and-seek with the network stack until it also gets the metadata
frame, and then presents a single packet, the timestamped PTP packet.
But when RX timestamping isn't enabled, there is no metadata frame
expected, so the hide-and-seek game must be turned off and the packet
must be delivered right away to the network stack.
Considering this, we create a pseudo isolation by devising two tagger
methods callable by the switch: one to get the RX timestamping state,
and one to set it. Since we can't export symbols between the tagger and
the switch driver, these methods are exposed through function pointers.
After this change, the public portion of the sja1105_tagger_data
contains only function pointers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
protocol driver"
This reverts commit 6d709cadfde68dbd12bef12fcced6222226dcb06.
The above change was done to avoid calling symbols exported by the
switch driver from the tagging protocol driver.
With the tagger-owned storage model, we have a new option on our hands,
and that is for the switch driver to provide a data consumer handler in
the form of a function pointer inside the ->connect_tag_protocol()
method. Having a function pointer avoids the problems of the exported
symbols approach.
By creating a handler for metadata frames holding TX timestamps on
SJA1110, we are able to eliminate an skb queue from the tagger data, and
replace it with a simple, and stateless, function pointer. This skb
queue is now handled exclusively by sja1105_ptp.c, which makes the code
easier to follow, as it used to be before the reverted patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, struct sja1105_tagger_data is a part of struct
sja1105_private, and is used by the sja1105 driver to populate dp->priv.
With the movement towards tagger-owned storage, the sja1105 driver
should not be the owner of this memory.
This change implements the connection between the sja1105 switch driver
and its tagging protocol, which means that sja1105_tagger_data no longer
stays in dp->priv but in ds->tagger_data, and that the sja1105 driver
now only populates the sja1105_port_deferred_xmit callback pointer.
The kthread worker is now the responsibility of the tagger.
The sja1105 driver also alters the tagger's state some more, especially
with regard to the PTP RX timestamping state. This will be fixed up a
bit in further changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX timestamp ID is incremented by the SJA1110 PTP timestamping
callback (->port_tx_timestamp) for every packet, when cloning it.
It isn't used by the tagger at all, even though it sits inside the
struct sja1105_tagger_data.
Also, serialization to this structure is currently done through
tagger_data->meta_lock, which is a cheap hack because the meta_lock
isn't used for anything else on SJA1110 (sja1105_rcv_meta_state_machine
isn't called).
This change moves ts_id from sja1105_tagger_data to sja1105_private and
introduces a dedicated spinlock for it, also in sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The design of the sja1105 tagger dp->priv is that each port has a
separate struct sja1105_port, and the sp->data pointer points to a
common struct sja1105_tagger_data.
We have removed all per-port members accessible by the tagger, and now
only struct sja1105_tagger_data remains. Make dp->priv point directly to
this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tagger property is in fact not used at all by the tagger, only by
the switch driver. Therefore it makes sense to be moved to
sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the ocelot-8021q driver was converted to deferred xmit as part of
commit 8d5f7954b7c8 ("net: dsa: felix: break at first CPU port during
init and teardown"), the deferred implementation was deliberately made
subtly different from what sja1105 has.
The implementation differences lied on the following observations:
- There might be a race between these two lines in tag_sja1105.c:
skb_queue_tail(&sp->xmit_queue, skb_get(skb));
kthread_queue_work(sp->xmit_worker, &sp->xmit_work);
and the skb dequeue logic in sja1105_port_deferred_xmit(). For
example, the xmit_work might be already queued, however the work item
has just finished walking through the skb queue. Because we don't
check the return code from kthread_queue_work, we don't do anything if
the work item is already queued.
However, nobody will take that skb and send it, at least until the
next timestampable skb is sent. This creates additional (and
avoidable) TX timestamping latency.
To close that race, what the ocelot-8021q driver does is it doesn't
keep a single work item per port, and a skb timestamping queue, but
rather dynamically allocates a work item per packet.
- It is also unnecessary to have more than one kthread that does the
work. So delete the per-port kthread allocations and replace them with
a single kthread which is global to the switch.
This change brings the two implementations in line by applying those
observations to the sja1105 driver as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This code is not necessary and complicates the conversion of this driver
to tagger-owned memory. If there is a PTP packet that is sent
concurrently with the port getting disabled, the deferred xmit mechanism
is robust enough to time out when it sees that it hasn't been delivered,
and recovers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The felix driver makes very light use of dp->priv, and the tagger is
effectively stateless. dp->priv is practically only needed to set up a
callback to perform deferred xmit of PTP and STP packets using the
ocelot-8021q tagging protocol (the main ocelot tagging protocol makes no
use of dp->priv, although this driver sets up dp->priv irrespective of
actual tagging protocol in use).
struct felix_port (what used to be pointed to by dp->priv) is removed
and replaced with a two-sided structure. The public side of this
structure, visible to the switch driver, is ocelot_8021q_tagger_data.
The private side is ocelot_8021q_tagger_private, and the latter
structure physically encapsulates the former. The public half of the
tagger data structure can be accessed through a helper of the same name
(ocelot_8021q_tagger_data) which also sanity-checks the protocol
currently in use by the switch. The public/private split was requested
by Andrew Lunn.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a typical mv88e6xxx switch tree like this:
CPU
| .----.
.--0--. | .--0--.
| sw0 | | | sw1 |
'-1-2-' | '-1-2-'
'---'
If sw1p{1,2} are added to a bridge that sw0p1 is not a part of, sw0
still needs to add a crosschip PVT entry for the virtual DSA device
assigned to represent the bridge.
Fixes: ce5df6894a57 ("net: dsa: mv88e6xxx: map virtual bridges with forwarding offload in the PVT")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f7f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid a memory leak if there is not a CPU port defined.
Fixes: 8d5f7954b7c8 ("net: dsa: felix: break at first CPU port during init and teardown")
Addresses-Coverity-ID: 1492897 ("Resource leak")
Addresses-Coverity-ID: 1492899 ("Resource leak")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211209110538.11585-1-jose.exposito89@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Added default case to handle undefined cmode scenario in
mv88e6393x_serdes_power() and mv88e6393x_serdes_power() methods.
Addresses-Coverity: 1494644 ("Uninitialized scalar variable")
Fixes: 21635d9203e1c (net: dsa: mv88e6xxx: Fix application of erratum 4.8 for 88E6393X)
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Ameer Hamza <amhamza.mgc@gmail.com>
Link: https://lore.kernel.org/r/20211209041552.9810-1-amhamza.mgc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit fixes a misunderstanding in commit 4a3e0aeddf09 ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7ac (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf09
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf09 ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We don't really need new switch API for these, and with new switches
which intend to add support for this feature, it will become cumbersome
to maintain.
The change consists in restructuring the two drivers that implement this
offload (sja1105 and mv88e6xxx) such that the offload is enabled and
disabled from the ->port_bridge_{join,leave} methods instead of the old
->port_bridge_tx_fwd_{,un}offload.
The only non-trivial change is that mv88e6xxx_map_virtual_bridge_to_pvt()
has been moved to avoid a forward declaration, and the
mv88e6xxx_reg_lock() calls from inside it have been removed, since
locking is now done from mv88e6xxx_port_bridge_{join,leave}.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
comparison
The goal of this change is to reduce mv88e6xxx_port_vlan() to a form
where dsa_port_bridge_same() can be used, since the dp->bridge_dev
pointer will be hidden in a future change.
To do that, we observe that the "br" pointer is deduced from a
dp->bridge_dev in both cases (of a physical switch port as well as a
virtual bridge). So instead of keeping the "br" pointer, we can just
keep the "dp" pointer from which "br" gets derived.
In the last iteration over switch ports, we must use another iterator
variable, "other_dp"since now we use the "dp" variable to keep an
indirect reference to the bridge. While at it, the old code used to
filter only the ports which were part of the same switch as "ds".
There exists a dedicated DSA port iterator for that:
dsa_switch_for_each_port (which skips the ports in the tree that belong
to non-local switches), so we can just use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88e6xxx_port_check_hw_vlan
Avoid a plethora of dsa_to_port() calls (some hidden behind
dsa_is_*_port and some in plain sight) by keeping two struct dsa_port
references: one to the port passed as argument, and another to the other
ports of the switch that we're iterating over.
This isn't called from the DSA initialization path, so there is no risk
that we have user ports without a dp->slave populated. So the combined
checks that a port isn't a DSA port, a CPU port, or doesn't have a slave
net device (therefore is unused), are strictly equivalent to the simple
check that the port is a user port. This is already handled by the DSA
iterator.
i gets replaced by other_dp->index, dsa_is_*_port calls get replaced by
dsa_port_is_*, and dsa_to_port gets replaced by the respective pointer
directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid repeated calls to dsa_to_port() (some hidden behind dsa_is_user_port
and some in plain sight) by keeping two struct dsa_port references: one
to the port passed as argument, and another to the other ports of the
switch that we're iterating over.
dsa_to_port(ds, i) gets replaced by other_dp, i gets replaced by
other_port which is derived from other_dp->index, dsa_is_user_port is
handled by the DSA iterator.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The service where DSA assigns a unique bridge number for each forwarding
domain is useful even for drivers which do not implement the TX
forwarding offload feature.
For example, drivers might use the dp->bridge_num for FDB isolation.
So rename ds->num_fwd_offloading_bridges to ds->max_num_bridges, and
calculate a unique bridge_num for all drivers that set this value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
