| Age | Commit message (Collapse) | Author |
|---|
|
Populate the supported interfaces and MAC capabilities for the Lantiq
DSA switches and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
The exclusion of Gigabit linkmodes for MII, Reverse MII and Reduced MII
links is handled within phylink_generic_validate() in phylink, so there
is no need to make them conditional on the interface mode in the driver.
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Populate the supported interfaces and MAC capabilities for the
hellcreek DSA switch and remove the old validate implementation to
allow DSA to use phylink_generic_validate() for this switch driver.
The switch actually only supports MII and RGMII, but as phylib defaults
to GMII, we need to include this interface mode to keep existing DT
working.
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c7bd3 ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings
in mac_config") removed forcing of speed and duplex from
mv88e6xxx_mac_config(), where the link is forced down, and left it only
in mv88e6xxx_mac_link_up(), by which time link is unforced.
It seems that (at least on 88E6190) when changing cmode to 2500base-x,
if the link is not forced down, but the speed or duplex are still
forced, the forcing of new settings for speed & duplex doesn't take in
mv88e6xxx_mac_link_up().
Fix this by unforcing speed & duplex in mv88e6xxx_mac_link_down().
Fixes: 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings in mac_config")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f7f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid a memory leak if there is not a CPU port defined.
Fixes: 8d5f7954b7c8 ("net: dsa: felix: break at first CPU port during init and teardown")
Addresses-Coverity-ID: 1492897 ("Resource leak")
Addresses-Coverity-ID: 1492899 ("Resource leak")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211209110538.11585-1-jose.exposito89@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Added default case to handle undefined cmode scenario in
mv88e6393x_serdes_power() and mv88e6393x_serdes_power() methods.
Addresses-Coverity: 1494644 ("Uninitialized scalar variable")
Fixes: 21635d9203e1c (net: dsa: mv88e6xxx: Fix application of erratum 4.8 for 88E6393X)
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Ameer Hamza <amhamza.mgc@gmail.com>
Link: https://lore.kernel.org/r/20211209041552.9810-1-amhamza.mgc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit fixes a misunderstanding in commit 4a3e0aeddf09 ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7ac (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf09
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf09 ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function mv88e6xxx_serdes_pcs_get_state() currently does not report link
up if AN is enabled, Link bit is set, but Speed and Duplex Resolved bit
is not set, which testing shows is the case for when auto-negotiation
was bypassed (we have AN enabled but link partner does not).
An example of such link partner is Marvell 88X3310 PHY, when put into
the mode where host interface changes between 10gbase-r, 5gbase-r,
2500base-x and sgmii according to copper speed. The 88X3310 does not
enable AN in 2500base-x, and so SerDes on mv88e6xxx currently does not
link with it.
Fix this.
Fixes: a5a6858b793f ("net: dsa: mv88e6xxx: extend phylink to Serdes PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inband AN is broken on Amethyst in 2500base-x mode when set by standard
mechanism (via cmode).
(There probably is some weird setting done by default in the switch for
this mode that make it cycle in some state or something, because when
the peer is the mvneta controller, it receives link change interrupts
every ~0.3ms, but the link is always down.)
Get around this by configuring the PCS mode to 1000base-x (where inband
AN works), and then changing the SerDes frequency while SerDes
transmitter and receiver are disabled, before enabling SerDes PHY. After
disabling SerDes PHY, change the PCS mode back to 2500base-x, to avoid
confusing the device (if we leave it at 1000base-x PCS mode but with
different frequency, and then change cmode to sgmii, the device won't
change the frequency because it thinks it already has the correct one).
The register which changes the frequency is undocumented. I discovered
it by going through all registers in the ranges 4.f000-4.f100 and
1e.8000-1e.8200 for all SerDes cmodes (sgmii, 1000base-x, 2500base-x,
5gbase-r, 10gbase-r, usxgmii) and filtering out registers that didn't
make sense (the value was the same for modes which have different
frequency). The result of this was:
reg sgmii 1000base-x 2500base-x 5gbase-r 10gbase-r usxgmii
04.f002 005b 0058 0059 005c 005d 005f
04.f076 3000 0000 1000 4000 5000 7000
04.f07c 0950 0950 1850 0550 0150 0150
1e.8000 0059 0059 0058 0055 0051 0051
1e.8140 0e20 0e20 0e28 0e21 0e42 0e42
Register 04.f002 is the documented Port Operational Confiuration
register, it's last 3 bits select PCS type, so changing this register
also changes the frequency to the appropriate value.
Registers 04.f076 and 04.f07c are not writable.
Undocumented register 1e.8000 was the one: changing bits 3:0 from 9 to 8
changed SerDes frequency to 3.125 GHz, while leaving the value of PCS
mode in register 04.f002.2:0 at 1000base-x. Inband autonegotiation
started working correctly.
(I didn't try anything with register 1e.8140 since 1e.8000 solved the
problem.)
Since I don't have documentation for this register 1e.8000.3:0, I am
using the constants without names, but my hypothesis is that this
register selects PHY frequency. If in the future I have access to an
oscilloscope able to handle these frequencies, I will try to test this
hypothesis.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add fix for erratum 5.2 of the 88E6393X (Amethyst) family: for 10gbase-r
mode, some undocumented registers need to be written some special
values.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Save power on 88E6393X by disabling SerDes receiver and transmitter
after SerDes is SerDes is disabled.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for lane is unnecessary, since the function is called only
with allowed lane argument.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to SERDES scripts for 88E6393X, erratum 4.8 has to be applied
every time before SerDes is powered on.
Split the code for erratum 4.8 into separate function and call it in
mv88e6393x_serdes_power().
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.
This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.
rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.
Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e25 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
qca8k has a global MTU, so its tracking the MTU per port to make sure
that the largest MTU gets applied.
Since it uses the frame size instead of MTU the driver MTU change function
will then add the size of Ethernet header and checksum on top of MTU.
The driver currently populates the per port MTU size as Ethernet frame
length + checksum which equals 1518.
The issue is that then MTU change function will go through all of the
ports, find the largest MTU and apply the Ethernet header + checksum on
top of it again, so for a desired MTU of 1500 you will end up with 1536.
This is obviously incorrect, so to correct it populate the per port struct
MTU with just the MTU and not include the Ethernet header + checksum size
as those will be added by the MTU change function.
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With SGMII phy the internal delay is always applied to the PAD0 config.
This is caused by the falling edge configuration that hardcode the reg
to PAD0 (as the falling edge bits are present only in PAD0 reg)
Move the delay configuration before the reg overwrite to correctly apply
the delay.
Fixes: cef08115846e ("net: dsa: qca8k: set internal delay also for sgmii")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Model 88E6191X only supports >1G speeds on port 10. Port 0 and 9 are
only 1G.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211104171747.10509-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Normally it is expected that the dsa_device_ops :: rcv() method finishes
parsing the DSA tag and consumes it, then never looks at it again.
But commit c0bcf537667c ("net: dsa: ocelot: add hardware timestamping
support for Felix") added support for RX timestamping in a very
unconventional way. On this switch, a partial timestamp is available in
the DSA header, but the driver got away with not parsing that timestamp
right away, but instead delayed that parsing for a little longer:
dsa_switch_rcv():
nskb = cpu_dp->rcv(skb, dev); <------------- not here
-> ocelot_rcv()
...
skb = nskb;
skb_push(skb, ETH_HLEN);
skb->pkt_type = PACKET_HOST;
skb->protocol = eth_type_trans(skb, skb->dev);
...
if (dsa_skb_defer_rx_timestamp(p, skb)) <--- but here
-> felix_rxtstamp()
return 0;
When in felix_rxtstamp(), this driver accounted for the fact that
eth_type_trans() happened in the meanwhile, so it got a hold of the
extraction header again by subtracting (ETH_HLEN + OCELOT_TAG_LEN) bytes
from the current skb->data.
This worked for quite some time but was quite fragile from the very
beginning. Not to mention that having DSA tag parsing split in two
different files, under different folders (net/dsa/tag_ocelot.c vs
drivers/net/dsa/ocelot/felix.c) made it quite non-obvious for patches to
come that they might break this.
Finally, the blamed commit does the following: at the end of
ocelot_rcv(), it checks whether the skb payload contains a VLAN header.
If it does, and this port is under a VLAN-aware bridge, that VLAN ID
might not be correct in the sense that the packet might have suffered
VLAN rewriting due to TCAM rules (VCAP IS1). So we consume the VLAN ID
from the skb payload using __skb_vlan_pop(), and take the classified
VLAN ID from the DSA tag, and construct a hwaccel VLAN tag with the
classified VLAN, and the skb payload is VLAN-untagged.
The big problem is that __skb_vlan_pop() does:
memmove(skb->data + VLAN_HLEN, skb->data, 2 * ETH_ALEN);
__skb_pull(skb, VLAN_HLEN);
aka it moves the Ethernet header 4 bytes to the right, and pulls 4 bytes
from the skb headroom (effectively also moving skb->data, by definition).
So for felix_rxtstamp()'s fragile logic, all bets are off now.
Instead of having the "extraction" pointer point to the DSA header,
it actually points to 4 bytes _inside_ the extraction header.
Corollary, the last 4 bytes of the "extraction" header are in fact 4
stale bytes of the destination MAC address from the Ethernet header,
from prior to the __skb_vlan_pop() movement.
So of course, RX timestamps are completely bogus when the system is
configured in this way.
The fix is actually very simple: just don't structure the code like that.
For better or worse, the DSA PTP timestamping API does not offer a
straightforward way for drivers to present their RX timestamps, but
other drivers (sja1105) have established a simple mechanism to carry
their RX timestamp from dsa_device_ops :: rcv() all the way to
dsa_switch_ops :: port_rxtstamp() and even later. That mechanism is to
simply save the partial timestamp to the skb->cb, and complete it later.
Question: why don't we simply populate the skb's struct
skb_shared_hwtstamps from ocelot_rcv(), and bother with this
complication of propagating the timestamp to felix_rxtstamp()?
Answer: dsa_switch_ops :: port_rxtstamp() answers the question whether
PTP packets need sleepable context to retrieve the full RX timestamp.
Currently felix_rxtstamp() answers "no, thanks" to that question, and
calls ocelot_ptp_gettime64() from softirq atomic context. This is
understandable, since Felix VSC9959 is a PCIe memory-mapped switch, so
hardware access does not require sleeping. But the felix driver is
preparing for the introduction of other switches where hardware access
is over a slow bus like SPI or MDIO:
https://lore.kernel.org/lkml/20210814025003.2449143-1-colin.foster@in-advantage.com/
So I would like to keep this code structure, so the rework needed when
that driver will need PTP support will be minimal (answer "yes, I need
deferred context for this skb's RX timestamp", then the partial
timestamp will still be found in the skb->cb.
Fixes: ea440cd2d9b2 ("net: dsa: tag_ocelot: use VLAN information from tagging header when available")
Reported-by: Po Liu <po.liu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some device set MAC06 exchange in the bootloader. This cause some
problem as we don't support this strange mode and we just set the port6
as the primary CPU port. With MAC06 exchange, PAD0 reg configure port6
instead of port0. Add an extra check and explicitly disable MAC06 exchange
to correctly configure the port PAD config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fixes: 3fcf734aa482 ("net: dsa: qca8k: add support for cpu port 6")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GSWIP switch accesses various bridging layer tables (VLANs, FDBs,
forwarding rules) indirectly through PCE registers. These hardware
accesses are non-atomic, being comprised of several register reads and
writes.
These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().
So this driver needs to serialize the access to the PCE registers using
its own locking scheme. This patch adds that.
Note that the driver also uses the gswip_pce_load_microcode() function
to load a static configuration for the packet classification engine into
a table using the same registers. It is currently not protected, but
since that configuration is only done from the dsa_switch_ops :: setup
method, there is no risk of it being concurrent with other operations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105 hardware seems as concurrent as can be, but when we create a
background script that adds/removes a rain of FDB entries without the
rtnl_mutex taken, then in parallel we do another operation like run
'bridge fdb show', we can notice these errors popping up:
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:40 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:40 vid 0 to fdb: -2
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:46 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:46 vid 0 to fdb: -2
Luckily what is going on does not require a major rework in the driver.
The sja1105_dynamic_config_read() function sends multiple SPI buffers to
the peripheral until the operation completes. We should not do anything
until the hardware clears the VALID bit.
But since there is no locking (i.e. right now we are implicitly
serialized by the rtnl_mutex, but if we remove that), it might be
possible that the process which performs the dynamic config read is
preempted and another one performs a dynamic config write.
What will happen in that case is that sja1105_dynamic_config_read(),
when it resumes, expects to see VALIDENT set for the entry it reads
back. But it won't.
This can be corrected by introducing a mutex for serializing SPI
accesses to the dynamic config interface which should be atomic with
respect to each other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware manual says that software should attempt a new dynamic
config access (be it a a write or a read-back) only while the VALID bit
is cleared. The VALID bit is set by software to 1, and it remains set as
long as the hardware is still processing the request.
Currently the driver only polls for the command completion only for
reads, because that's when we need the actual data read back. Writes
have been more or less "asynchronous", although this has never been an
observable issue.
This change makes sja1105_dynamic_config_write poll the VALID bit as
well, to absolutely ensure that a follow-up access to the static config
finds the VALID bit cleared.
So VALID means "work in progress", while VALIDENT means "entry being
read is valid". On reads we check the VALIDENT bit too, while on writes
that bit is not always defined. So we need to factor it out of the loop,
and make the loop provide back the unpacked command structure, so that
sja1105_dynamic_config_read can check the VALIDENT bit.
The change also attempts to convert the open-coded loop to use the
read_poll_timeout macro, since I know this will come up during review.
It's more code, but hey, it uses read_poll_timeout!
Tested on SJA1105T, SJA1105S, SJA1110A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 965e6b262f48257dbdb51b565ecfd84877a0ab5f, reversing
changes made to 4d98bb0d7ec2d0b417df6207b0bafe1868bad9f8.
|
|
This converts instances of
bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS)
to
linkmode_foo(args...)
I manually fixed up some lines to prevent them from being excessively
long. Otherwise, this change was generated with the following semantic
patch:
// Generated with
// echo linux/linkmode.h > includes
// git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \
// | sort | uniq | tee new_includes | wc -l && mv new_includes includes
// and repeating until the number stopped going up
@i@
@@
(
#include <linux/acpi_mdio.h>
|
#include <linux/brcmphy.h>
|
#include <linux/dsa/loop.h>
|
#include <linux/dsa/sja1105.h>
|
#include <linux/ethtool.h>
|
#include <linux/ethtool_netlink.h>
|
#include <linux/fec.h>
|
#include <linux/fs_enet_pd.h>
|
#include <linux/fsl/enetc_mdio.h>
|
#include <linux/fwnode_mdio.h>
|
#include <linux/linkmode.h>
|
#include <linux/lsm_audit.h>
|
#include <linux/mdio-bitbang.h>
|
#include <linux/mdio.h>
|
#include <linux/mdio-mux.h>
|
#include <linux/mii.h>
|
#include <linux/mii_timestamper.h>
|
#include <linux/mlx5/accel.h>
|
#include <linux/mlx5/cq.h>
|
#include <linux/mlx5/device.h>
|
#include <linux/mlx5/driver.h>
|
#include <linux/mlx5/eswitch.h>
|
#include <linux/mlx5/fs.h>
|
#include <linux/mlx5/port.h>
|
#include <linux/mlx5/qp.h>
|
#include <linux/mlx5/rsc_dump.h>
|
#include <linux/mlx5/transobj.h>
|
#include <linux/mlx5/vport.h>
|
#include <linux/of_mdio.h>
|
#include <linux/of_net.h>
|
#include <linux/pcs-lynx.h>
|
#include <linux/pcs/pcs-xpcs.h>
|
#include <linux/phy.h>
|
#include <linux/phy_led_triggers.h>
|
#include <linux/phylink.h>
|
#include <linux/platform_data/bcmgenet.h>
|
#include <linux/platform_data/xilinx-ll-temac.h>
|
#include <linux/pxa168_eth.h>
|
#include <linux/qed/qed_eth_if.h>
|
#include <linux/qed/qed_fcoe_if.h>
|
#include <linux/qed/qed_if.h>
|
#include <linux/qed/qed_iov_if.h>
|
#include <linux/qed/qed_iscsi_if.h>
|
#include <linux/qed/qed_ll2_if.h>
|
#include <linux/qed/qed_nvmetcp_if.h>
|
#include <linux/qed/qed_rdma_if.h>
|
#include <linux/sfp.h>
|
#include <linux/sh_eth.h>
|
#include <linux/smsc911x.h>
|
#include <linux/soc/nxp/lpc32xx-misc.h>
|
#include <linux/stmmac.h>
|
#include <linux/sunrpc/svc_rdma.h>
|
#include <linux/sxgbe_platform.h>
|
#include <net/cfg80211.h>
|
#include <net/dsa.h>
|
#include <net/mac80211.h>
|
#include <net/selftests.h>
|
#include <rdma/ib_addr.h>
|
#include <rdma/ib_cache.h>
|
#include <rdma/ib_cm.h>
|
#include <rdma/ib_hdrs.h>
|
#include <rdma/ib_mad.h>
|
#include <rdma/ib_marshall.h>
|
#include <rdma/ib_pack.h>
|
#include <rdma/ib_pma.h>
|
#include <rdma/ib_sa.h>
|
#include <rdma/ib_smi.h>
|
#include <rdma/ib_umem.h>
|
#include <rdma/ib_umem_odp.h>
|
#include <rdma/ib_verbs.h>
|
#include <rdma/iw_cm.h>
|
#include <rdma/mr_pool.h>
|
#include <rdma/opa_addr.h>
|
#include <rdma/opa_port_info.h>
|
#include <rdma/opa_smi.h>
|
#include <rdma/opa_vnic.h>
|
#include <rdma/rdma_cm.h>
|
#include <rdma/rdma_cm_ib.h>
|
#include <rdma/rdmavt_cq.h>
|
#include <rdma/rdma_vt.h>
|
#include <rdma/rdmavt_qp.h>
|
#include <rdma/rw.h>
|
#include <rdma/tid_rdma_defs.h>
|
#include <rdma/uverbs_ioctl.h>
|
#include <rdma/uverbs_named_ioctl.h>
|
#include <rdma/uverbs_std_types.h>
|
#include <rdma/uverbs_types.h>
|
#include <soc/mscc/ocelot.h>
|
#include <soc/mscc/ocelot_ptp.h>
|
#include <soc/mscc/ocelot_vcap.h>
|
#include <trace/events/ib_mad.h>
|
#include <trace/events/rdma_core.h>
|
#include <trace/events/rdma.h>
|
#include <trace/events/rpcrdma.h>
|
#include <uapi/linux/ethtool.h>
|
#include <uapi/linux/ethtool_netlink.h>
|
#include <uapi/linux/mdio.h>
|
#include <uapi/linux/mii.h>
)
@depends on i@
expression list args;
@@
(
- bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_zero(args)
|
- bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_copy(args)
|
- bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_and(args)
|
- bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_or(args)
|
- bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_empty(args)
|
- bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_andnot(args)
|
- bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_equal(args)
|
- bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_intersects(args)
|
- bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_subset(args)
)
Add missing linux/mii.h include to mellanox. -DaveM
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looking at the code, the GSWIP switch appears to hold bridging service
structures (VLANs, FDBs, forwarding rules) in PCE table entries.
Hardware access to the PCE table is non-atomic, and is comprised of
several register reads and writes.
These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().
So this driver needs to serialize the access to the PCE table using its
own locking scheme. This patch adds that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105 hardware seems as concurrent as can be, but when we create a
background script that adds/removes a rain of FDB entries without the
rtnl_mutex taken, then in parallel we do another operation like run
'bridge fdb show', we can notice these errors popping up:
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:40 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:40 vid 0 to fdb: -2
sja1105 spi2.0: port 2 failed to read back entry for 00:01:02:03:00:46 vid 0: -ENOENT
sja1105 spi2.0: port 2 failed to add 00:01:02:03:00:46 vid 0 to fdb: -2
Luckily what is going on does not require a major rework in the driver.
The sja1105_dynamic_config_read() function sends multiple SPI buffers to
the peripheral until the operation completes. We should not do anything
until the hardware clears the VALID bit.
But since there is no locking (i.e. right now we are implicitly
serialized by the rtnl_mutex, but if we remove that), it might be
possible that the process which performs the dynamic config read is
preempted and another one performs a dynamic config write.
What will happen in that case is that sja1105_dynamic_config_read(),
when it resumes, expects to see VALIDENT set for the entry it reads
back. But it won't.
This can be corrected by introducing a mutex for serializing SPI
accesses to the dynamic config interface which should be atomic with
respect to each other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware manual says that software should attempt a new dynamic
config access (be it a a write or a read-back) only while the VALID bit
is cleared. The VALID bit is set by software to 1, and it remains set as
long as the hardware is still processing the request.
Currently the driver only polls for the command completion only for
reads, because that's when we need the actual data read back. Writes
have been more or less "asynchronous", although this has never been an
observable issue.
This change makes sja1105_dynamic_config_write poll the VALID bit as
well, to absolutely ensure that a follow-up access to the static config
finds the VALID bit cleared.
So VALID means "work in progress", while VALIDENT means "entry being
read is valid". On reads we check the VALIDENT bit too, while on writes
that bit is not always defined. So we need to factor it out of the loop,
and make the loop provide back the unpacked command structure, so that
sja1105_dynamic_config_read can check the VALIDENT bit.
The change also attempts to convert the open-coded loop to use the
read_poll_timeout macro, since I know this will come up during review.
It's more code, but hey, it uses read_poll_timeout!
Tested on SJA1105T, SJA1105S, SJA1110A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following coccicheck warning:
./drivers/net/dsa/sja1105/sja1105_main.c:1193:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Fixes: 9ca482a246f0 ("net: dsa: sja1105: parse {rx, tx}-internal-delay-ps properties for RGMII delays")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211021094606.7118-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Lots of simnple overlapping additions.
With a build fix from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass a single argument to dsa_8021q_rx_vid and dsa_8021q_tx_vid that
contains the necessary information from the two arguments that are
currently provided: the switch and the port number.
Also rename those functions so that they have a dsa_port_* prefix, since
they operate on a struct dsa_port *.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tidy and organize qca8k setup function from multiple for loop.
Change for loop in bridge leave/join to scan all port and skip cpu port.
No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change does not fix any functional issue or address any real life
use case that wasn't possible before. It is just a small step in the
process of standardizing the way in which Ethernet MAC drivers may apply
RGMII delays (traditionally these have been applied by PHYs, with no
clear definition of what to do in the case of a fixed-link).
The sja1105 driver used to apply MAC-level RGMII delays on the RX data
lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or
"rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id".
But the standard definitions don't say anything about behaving
differently when the port is in fixed-link vs when it isn't, and the new
device tree bindings are about having a way of applying the delays in a
way that is independent of the phy-mode and of the fixed-link property.
When the {rx,tx}-internal-delay-ps properties are present, use them,
otherwise fall back to the old behavior and warn.
One other thing to note is that the SJA1105 hardware applies a delay
value in degrees rather than in picoseconds (the delay in ps changes
depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at
100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase
shift of the internal delay lines assuming that the device tree meant
gigabit, and we let the hardware scale those according to the link speed.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/
Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix delay settings applied to wrong cpu in parse_port_config. The delay
values is set to the wrong index as the cpu_port_index is incremented
too early. Start the cpu_port_index to -1 so the correct value is
applied to address also the case with invalid phy mode and not available
port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M switch controller. The driver has been developed based on a
GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found
in the OpenWrt source tree.
Despite the name, the RTL8365MB-VC has an entirely different register
layout to the already-supported RTL8366RB ASIC. Notwithstanding this,
the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb
subdriver. Like the 'rb, it establishes its own irqchip to handle
cascaded PHY link status interrupts.
The RTL8365MB-VC switch is capable of offloading a large number of
features from the software, but this patch introduces only the most
basic DSA driver functionality. The ports always function as standalone
ports, with bridging handled in software.
One more thing. Realtek's nomenclature for switches makes it hard to
know exactly what other ASICs might be supported by this driver. The
vendor driver goes by the name rtl8367c, but as far as I can tell, no
chip actually exists under this name. As such, the subdriver is named
rtl8365mb to emphasize the potentially limited support. But it is clear
from the vendor sources that a number of other more advanced switches
share a similar register layout, and further support should not be too
hard to add given access to the relevant hardware. With this in mind,
the subdriver has been written with as few assumptions about the
particular chip as is reasonable. But the RTL8365MB-VC is the only
hardware I have available, so some further work is surely needed.
Co-developed-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move ports related config to dedicated struct to keep things organized.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
