| Age | Commit message (Collapse) | Author |
|---|
|
bcmgenet_mii_setup() is called from the PHY state machine every 1-2 seconds
when the PHYs are in PHY_POLL mode.
Improve bcmgenet_mii_setup() so that it touches the MAC registers only when
the link is up and there was a change to link, speed, duplex, or pause status.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit bc23333ba11fb7f959b7e87e121122f5a0fbbca8 ("net:
bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb
pointer in case we had to reallocate the SKB headroom.
Fixes: 80105befdb4b8 ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_put_tx_csum() needs to return skb pointer back to the caller
because it reallocates a new one in case of lack of skb headroom.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_wol_resume() is only used in bcmgenet_resume(), which is only
defined when CONFIG_PM_SLEEP is enabled. This leads to the following
compile warning when building with !CONFIG_PM_SLEEP:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1967:12: warning: ‘bcmgenet_wol_resume’ defined but not used [-Wunused-function]
Since bcmgenet_resume() is the only user of bcmgenet_wol_resume(), fix
this by directly inlining the function there.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET driver supports SKB fragments, and succeeds in transmitting
them properly, but when reclaiming these transmitted fragments, we will
only update the count of free buffer descriptors by 1, even for SKBs
with fragments. This leads to the networking stack thinking it has more
room than the hardware has when pushing new SKBs, and backing off
consequently because we return NETDEV_TX_BUSY.
Fix this by accounting for the SKB nr_frags plus one (itself) and update
ring->free_bds accordingly with that value for each iteration loop in
__bcmgenet_tx_reclaim().
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using new Multi-function modes it's possible that due to incompatible
configuration management FW will fallback into an existing mode.
Notice that at the moment this fallback is exactly the same as the already
existing switch-independent multi-function mode, but we still use existing
infrastructure to hold this information [in case some small differences will
arise in the future].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a new multi-function mode based on the Unified Fabric Port
system specifications.
Support includes configuration of:
1. Outer vlan tags.
2. Bandwidth settings.
3. Virtual link enable/disable.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange macros to query for storage-only modes in different MF environment.
Improves the readibility and maintainability of the code. E.g.:
- if (IS_MF_STORAGE_SD(bp) || IS_MF_FCOE_AFEX(bp))
+ if (IS_MF_STORAGE_ONLY(bp))
In addition, this removes the need for bnx2x_is_valid_ether_addr().
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The integrated BCM7xxx PHY contains no useful revision information in
its MII_PHYSID2 bits 3:0, that information is instead contained in the
GENET hardware block.
We already read the GENET 32-bit revision register, so store the
integrated PHY revision in the driver private structure, and then
communicate this revision value to the PHY driver by overriding the
phy_flags value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nstat->multicast refers to received packets, not transmitted as
is returned here. Change it so that received packet stats are
given.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig
Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
This is a similar fix to the GENET one:
c677ba8b3c47650358572091ed8a6af50bfca877 ("net: bcmgenet: update
UMAC_CMD only when link is detected").
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.
This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.
First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.
Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().
v2: Added logging messages per Prashant's request
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Broadcom tags are enabled, e.g: when interfaced to an Ethernet
switch, make sure that we tell the RXCHK engine that it should be
expecting a 4-bytes Broadcom tag after the Ethernet MAC Source Address.
Use netdev_uses_dsa() to check for that condition since that will tell
us if a switch is attached to our network interface.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set correct bit for packed description.
Introduced in e42780b66aab88d3a82b6087bcd6095b90eecde7
bnx2x: Utilize FW 7.10.51
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes incorrectly defined struct in FW HSI for BE platform.
Affects tunneling, tx-switching and anti-spoofing.
Introduced in e42780b66aab88d3a82b6087bcd6095b90eecde7
bnx2x: Utilize FW 7.10.51
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a sprase warning introduced recently by commit
eeed018cbfa30 ("bnx2x: Add timestamping and PTP hardware clock support"),
as well as another unrelated sparse endian issue.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Incorrect checking of array instead of array contents in panic_dump
flow - results of commit e261199872a2 ("bnx2x: Safe bnx2x_panic_dump()").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x uses ptp functions, so it should select the provider of
those functions (PTP_1588_CLOCK). Fixes these build errors:
drivers/built-in.o: In function `__bnx2x_remove':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13409:
undefined reference to `ptp_clock_unregister'
drivers/built-in.o: In function `bnx2x_register_phc':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13202:
undefined reference to `ptp_clock_register'
drivers/built-in.o: In function `bnx2x_get_ts_info':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3498:
undefined reference to `ptp_clock_index'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit eeed018cbfa30 ("bnx2x: Add timestamping and PTP hardware clock support")
has a missing conversion to LE32, which will prevent the feature from working
on big endian machines.
Signed-off-by: Michal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This introduces 2 new relaxations in the bnx2x driver regarding GRO:
1. Don't prevent SW GRO if HW GRO is disabled.
2. If all aggregations are disabled, when GRO configuration changes
there's no need to perform an inner-reload [since it will have no
actual effect].
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During statistics initialization of a VF we need to clean its statistics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When STOP_ON_ERROR is set driver will not compile. Even if it did,
traffic will not pass without this patch as several fields which are
verified by FW/HW on the Tx path are not properly set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This changes slightly the set of registers read during `ethtool -d'.
Without this change, it's possible the HW will generate a grc Attention which
will be logged into system logs as `grc timeout'.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use is_kdump_kernel() to detect kdump kernel, instead of
reset_devices.
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pulling to get some TIPC fixes that a net-next series depends
upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is mostly a semantic change which modifies the code parsing and printing
of FW asserts.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent dereference of pointer in case it's NULL.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trying to disable sriov when VFs are assigned may lead to all kinds of problems.
This patch unifies the call in the driver to pci_disable_sriov() and prevents
them if some of the PF's child VFs are marked as assigned.
[Notice this is a bad scenario either way; User should not reach a point where
the OS tries to disable SRIOV when a VF is assigned - but currently there's no
way of preventing the user from doing so, and the ill-effect for the driver is
smaller this way]
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible there's a bad chip configuration which will result with
PCIe IOV capabilities, but with no available interrupts for VFs.
In such case, we want to gracefully prevent the PF from initializing its
IOV capabilities rather than encounter difficulties further along the way.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bnx2x panic dump spills a lot of information from the driver's
fastpath, but may be called while some of the fastpath is uninitialized.
This patch verifies that pointers are already allocated before dereferencing
them to prevent possible kernel panics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does several semantic things:
- Fixing typos.
- Removing unnecessary prints.
- Removing unused functions and definitions.
- Change 'strange' usage of boolean variables.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a PHC to the bnx2x driver. Driver supports timestamping send/receive
PTP packets, as well as adjusting the on-chip clock.
The driver has been tested with linuxptp project.
Signed-off-by: Michal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- (L2) In some multi-function configurations, inter-PF and inter-VF
Tx switching is incorrectly enabled.
- (L2) Wrong assert code in FLR final cleanup in case it is sent not
after FLR.
- (L2) Chip may stall in very rare cases under heavy traffic with FW GRO
enabled.
- (L2) VF malicious notification error fixes.
- (L2) Default gre tunnel to IPGRE which allows proper RSS for IPGRE packets,
L2GRE traffic will reach single queue.
- (FCoE) Fix data being placed in wrong buffer when corrupt FCoE frame is
received.
- (FCoE) Burst of FIP packets with destination MAC of ALL-FCF_MACs
causes FCoE traffic to stop.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "rcu_dereference()" calls are used directly in conditions.
Since their return values are never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacements.
The following Coccinelle semantic patch was used:
@@
@@
(
if(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
|
while(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
