| Age | Commit message (Collapse) | Author |
|---|
|
Integrate the common MAC endpoint management support into the
dpaa2-switch driver as well. Nothing special happens here, just that the
already available dpaa2-mac functions are also called from dpaa2-switch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for tc flower hardware offload on the ingress
path. Shared filter blocks are supported by sharing a single ACL table
between multiple ports.
The following flow keys are supported:
- Ethernet: dst_mac/src_mac
- IPv4: dst_ip/src_ip/ip_proto/tos
- VLAN: vlan_id/vlan_prio/vlan_tpid/vlan_dei
- L4: dst_port/src_port
As per flow actions, the following are supported:
- drop
- mirred egress redirect
- trap
Each ACL entry (filter) can be setup with only one of the listed
actions.
A sorted single linked list is used to keep the ACL entries by their
order of priority. When adding a new filter, this enables us to quickly
ascertain if the new entry has the highest priority of the entire block
or if we should make some space in the ACL table by increasing the
priority of the filters already in the table.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the dpaa2-switch driver has basic I/O capabilities on the
switch port net_devices and multiple bridging domains are supported,
move the driver out of staging.
The dpaa2-switch driver is placed right next to the dpaa2-eth driver
since, in the near future, they will be sharing most of the data path.
I didn't implement code reuse in this patch series because I wanted to
keep it as small as possible.
Also, the README is removed from staging with the intention to add
proper rst documentation afterwards to actually match was is supported
by the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support in dpaa2-eth for devlink. For the moment, just
register the device with devlink, add the corresponding devlink port and
implement the .info_get() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dpaa2-eth driver now has support for connecting to its associated
PHY device found through standard OF bindings.
This happens when the DPNI object (that the driver probes on) gets
connected to a DPMAC. When that happens, the device tree is looked up by
the DPMAC ID, and the associated PHY bindings are found.
The old logic of handling the net device's link state by hand still
needs to be kept, as the DPNI can be connected to other devices on the
bus than a DPMAC: other DPNI, DPSW ports, etc. This logic is only
engaged when there is no DPMAC (and therefore no phylink instance)
attached.
The MC firmware support multiple type of DPMAC links: TYPE_FIXED,
TYPE_PHY. The TYPE_FIXED mode does not require any DPMAC management from
Linux side, and as such, the driver will not handle such a DPMAC.
Although PHYLINK typically handles SFP cages and in-band AN modes, for
the moment the driver only supports the RGMII interfaces found on the
LX2160A. Support for other modes will come later.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export detailed driver counters through debugfs.
Statistics already available in ethtool are presented in a
structured manner. Includes per-core, per-FQ and per-channel statistics.
Also transition from module_fsl_mc_driver to explicit module_init/exit
in order to create the debugfs directory besides registering the driver.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DPAA2 Ethernet driver supports Freescale/NXP SoCs with DPAA2
(DataPath Acceleration Architecture v2). The driver manages
network objects discovered on the fsl-mc bus.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
