| Age | Commit message (Collapse) | Author |
|---|
|
When mirroring rules are added in shared filter blocks, the same
mirroring rule has to be configured on all the switch ports that are
part of the same block.
In case a switch port joins a shared block after mirroring filters have
been already added to it, then all the mirror rules should be offloaded
to the port. The reverse, removal of mirroring rules, has to be done at
block unbind.
For this purpose, the dpaa2_switch_block_offload_mirror() and
dpaa2_switch_block_unoffload_mirror() functions are added and called
upon binding and unbinding a switch port to/from a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the infrastructure added in the previous patch, extend tc-flower
support with FLOW_ACTION_MIRRED based on VLAN.
Tested with:
tc qdisc add dev eth8 ingress_block 1 clsact
tc filter add block 1 ingress protocol 802.1q flower skip_sw \
vlan_id 100 action mirred egress mirror dev eth6
tc filter del block 1 ingress pref 49152
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for per port mirroring for the DPAA2 switch. We support
only single mirror port, therefore we allow mirroring rules only as long
as the destination port is always the same.
Unlike all the actions (drop, redirect, trap) already supported by the
dpaa2-switch driver, adding mirroring filters in shared blocks is not
achieved by a singular ACL entry added in a table shared by the ports.
This is why, when a new mirror filter is added in a block we have to got
through all the switch ports sharing it and configure the filter
individually on all.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_matchall_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_flower_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, shared filter blocks were implemented only by ACL tables
shared between ports. Going forward, when the mirroring support will be
added, this will not be true anymore.
Rename the dpaa2_switch_acl_tbl into dpaa2_switch_filter_block so that
we make it clear that the structure is used not only for filters that
use the ACL table but will be used for all the filters that are added in
a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the dpaa2_switch_tc_parse_action() function was used for all
the supported tc actions since all of them were implemented by adding
ACL table entries. In the next commits, the dpaa2-switch driver will
gain mirroring support which is not using the same HW feature.
Make sure that we specify the ACL in the function name so that we make
it clear that it's only used for specific actions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we added the dpaa2_switch_acl_entry_add() function in the previous
patches to hide all the details of actually adding the ACL entry by
issuing a firmware command, let's use it also for adding a CPU trap for
the STP frames.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support TC_SETUP_CLSMATCHALL by using the same ACL table entries
framework as for tc flower. Adding a matchall rule is done by installing
an entry which has a mask of all zeroes, thus matching on any packet.
This can be used as a catch-all type of rule if used correctly, ie the
priority of the matchall filter should be kept as the lowest one in the
entire filter block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for tc flower hardware offload on the ingress
path. Shared filter blocks are supported by sharing a single ACL table
between multiple ports.
The following flow keys are supported:
- Ethernet: dst_mac/src_mac
- IPv4: dst_ip/src_ip/ip_proto/tos
- VLAN: vlan_id/vlan_prio/vlan_tpid/vlan_dei
- L4: dst_port/src_port
As per flow actions, the following are supported:
- drop
- mirred egress redirect
- trap
Each ACL entry (filter) can be setup with only one of the listed
actions.
A sorted single linked list is used to keep the ACL entries by their
order of priority. When adding a new filter, this enables us to quickly
ascertain if the new entry has the highest priority of the entire block
or if we should make some space in the ACL table by increasing the
priority of the filters already in the table.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
