summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/freescale/enetc/enetc_pf.c
AgeCommit message (Collapse)Author
2024-01-04net: enetc: allow phy-mode = "1000base-x"Vladimir Oltean
The driver code proper is handled by the lynx_pcs. The enetc just needs to populate phylink's supported_interfaces array, and return true for this phy-mode in enetc_port_has_pcs(), such that it creates an internal MDIO bus through which the Lynx PCS registers are accessed. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20240103113445.3892971-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-09-07net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()Vladimir Oltean
enetc_psi_create() returns an ERR_PTR() or a valid station interface pointer, but checking for the non-NULL quality of the return code blurs that difference away. So if enetc_psi_create() fails, we call enetc_psi_destroy() when we shouldn't. This will likely result in crashes, since enetc_psi_create() cleans up everything after itself when it returns an ERR_PTR(). Fixes: f0168042a212 ("net: enetc: reimplement RFS/RSS memory clearing as PCI quirk") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/netdev/582183ef-e03b-402b-8e2d-6d9bb3c83bd9@moroto.mountain/ Suggested-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230906141609.247579-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-09net: enetc: remove of_device_is_available() handlingVladimir Oltean
Since commit 6fffbc7ae137 ("PCI: Honor firmware's device disabled status"), this is redundant and does nothing, because enetc_pf_probe() no longer even gets called. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-09net: enetc: reimplement RFS/RSS memory clearing as PCI quirkVladimir Oltean
The workaround implemented in commit 3222b5b613db ("net: enetc: initialize RFS/RSS memories for unused ports too") is no longer effective after commit 6fffbc7ae137 ("PCI: Honor firmware's device disabled status"). Thus, it has introduced a regression and we see AER errors being reported again: $ ip link set sw2p0 up && dhclient -i sw2p0 && ip addr show sw2p0 fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode fsl_enetc 0000:00:00.2 eno2: Link is Up - 2.5Gbps/Full - flow control rx/tx mscc_felix 0000:00:00.5 swp2: configuring for fixed/sgmii link mode mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control off sja1105 spi2.2 sw2p0: configuring for phy/rgmii-id link mode sja1105 spi2.2 sw2p0: Link is Up - 1Gbps/Full - flow control off pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0 pcieport 0000:00:1f.0: AER: can't find device of ID0000 Rob's suggestion is to reimplement the enetc driver workaround as a PCI fixup, and to modify the PCI core to run the fixups for all PCI functions. This change handles the first part. We refactor the common code in enetc_psi_create() and enetc_psi_destroy(), and use the PCI fixup only for those functions for which enetc_pf_probe() won't get called. This avoids some work being done twice for the PFs which are enabled. Fixes: 6fffbc7ae137 ("PCI: Honor firmware's device disabled status") Link: https://lore.kernel.org/netdev/CAL_JsqLsVYiPLx2kcHkDQ4t=hQVCR7NHziDwi9cCFUFhx48Qow@mail.gmail.com/ Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-05-29net: enetc: use lynx_pcs_create_mdiodev()Russell King (Oracle)
Use the newly introduced lynx_pcs_create_mdiodev() which simplifies the creation and destruction of the lynx PCS. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-02-10Daniel Borkmann says:Jakub Kicinski
==================== pull-request: bpf-next 2023-02-11 We've added 96 non-merge commits during the last 14 day(s) which contain a total of 152 files changed, 4884 insertions(+), 962 deletions(-). There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c between commit 5b246e533d01 ("ice: split probe into smaller functions") from the net-next tree and commit 66c0e13ad236 ("drivers: net: turn on XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev() is otherwise there a 2nd time, and add XDP features to the existing ice_cfg_netdev() one: [...] ice_set_netdev_features(netdev); netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT | NETDEV_XDP_ACT_XSK_ZEROCOPY; ice_set_ops(netdev); [...] Stephen's merge conflict mail: https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/ The main changes are: 1) Add support for BPF trampoline on s390x which finally allows to remove many test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich. 2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski. 3) Add capability to export the XDP features supported by the NIC. Along with that, add a XDP compliance test tool, from Lorenzo Bianconi & Marek Majtyka. 4) Add __bpf_kfunc tag for marking kernel functions as kfuncs, from David Vernet. 5) Add a deep dive documentation about the verifier's register liveness tracking algorithm, from Eduard Zingerman. 6) Fix and follow-up cleanups for resolve_btfids to be compiled as a host program to avoid cross compile issues, from Jiri Olsa & Ian Rogers. 7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted when testing on different NICs, from Jesper Dangaard Brouer. 8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang. 9) Extend libbpf to add an option for when the perf buffer should wake up, from Jon Doron. 10) Follow-up fix on xdp_metadata selftest to just consume on TX completion, from Stanislav Fomichev. 11) Extend the kfuncs.rst document with description on kfunc lifecycle & stability expectations, from David Vernet. 12) Fix bpftool prog profile to skip attaching to offline CPUs, from Tonghao Zhang. ==================== Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-02-07net: enetc: add support for MAC Merge layerVladimir Oltean
Add PF driver support for viewing and changing the MAC Merge sublayer parameters, and seeing the verification state machine's current state. The verification handshake with the link partner is driven by hardware. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20230206094531.444988-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-02-02drivers: net: turn on XDP featuresMarek Majtyka
A summary of the flags being set for various drivers is given below. Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features that can be turned off and on at runtime. This means that these flags may be set and unset under RTNL lock protection by the driver. Hence, READ_ONCE must be used by code loading the flag value. Also, these flags are not used for synchronization against the availability of XDP resources on a device. It is merely a hint, and hence the read may race with the actual teardown of XDP resources on the device. This may change in the future, e.g. operations taking a reference on the XDP resources of the driver, and in turn inhibiting turning off this flag. However, for now, it can only be used as a hint to check whether device supports becoming a redirection target. Turn 'hw-offload' feature flag on for: - netronome (nfp) - netdevsim. Turn 'native' and 'zerocopy' features flags on for: - intel (i40e, ice, ixgbe, igc) - mellanox (mlx5). - stmmac - netronome (nfp) Turn 'native' features flags on for: - amazon (ena) - broadcom (bnxt) - freescale (dpaa, dpaa2, enetc) - funeth - intel (igb) - marvell (mvneta, mvpp2, octeontx2) - mellanox (mlx4) - mtk_eth_soc - qlogic (qede) - sfc - socionext (netsec) - ti (cpsw) - tap - tsnep - veth - xen - virtio_net. Turn 'basic' (tx, pass, aborted and drop) features flags on for: - netronome (nfp) - cavium (thunder) - hyperv. Turn 'redirect_target' feature flag on for: - amanzon (ena) - broadcom (bnxt) - freescale (dpaa, dpaa2) - intel (i40e, ice, igb, ixgbe) - ti (cpsw) - marvell (mvneta, mvpp2) - sfc - socionext (netsec) - qlogic (qede) - mellanox (mlx5) - tap - veth - virtio_net - xen Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Stanislav Fomichev <sdf@google.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Marek Majtyka <alardam@gmail.com> Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-01-23net: enetc: stop auto-configuring the port pMACVladimir Oltean
The pMAC (ENETC_PFPMR_PMACE) is probably unconditionally enabled in the enetc driver to allow RX of preemptible packets and not see them as error frames. I don't know why TX preemption (ENETC_MMCSR_ME) is enabled though. With no way to say which traffic classes are preemptible (all are express by default), no preemptible frames would be transmitted anyway. Lastly, it may have been believed that the register write lock-step mode (now deleted) needed the pMAC to be enabled at all times. I don't know if that's true. However, I've checked that driver writes to PM1 registers do propagate through to the ENETC IP even when the pMAC is disabled. With such incomplete support for frame preemption, it's best to just remove whatever exists right now and come with something more coherent later. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-01-23net: enetc: implement software lockstep for port MAC registersVladimir Oltean
Currently the enetc driver duplicates its writes to the PM0 registers also to PM1, but it doesn't do this consistently - for example we write to ENETC_PM0_MAXFRM but not to ENETC_PM1_MAXFRM. Create enetc_port_mac_wr() which writes both the PM0 and PM1 register with the same value (if frame preemption is supported on this port). Also create enetc_port_mac_rd() which reads from PM0 - the assumption being that PM1 contains just the same value. This will be necessary when we enable the MAC Merge layer properly, and the pMAC becomes operational. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-01-23net: enetc: stop configuring pMAC in lockstep with eMACVladimir Oltean
The MWLM bit (MAC write lock-step mode) allows register writes to the pMAC to be auto-performed whenever the corresponding eMAC register is written by the driver. This allows their configuration to remain in sync. The driver has set this bit since the initial commit, but it doesn't do anything, since the hardware feature doesn't work (and the bit has been removed from more recent versions of the documentation). The driver does attempt, more or less, to keep those MAC registers in sync by writing the same value once to e.g. ENETC_PM0_CMD_CFG (eMAC) and once to ENETC_PM1_CMD_CFG (pMAC). Because the lockstep feature doesn't work, that's what it will stick to. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-01-13enetc: Separate C22 and C45 transactionsAndrew Lunn
The enetc MDIO bus driver can perform both C22 and C45 transfers. Create separate functions for each and register the C45 versions using the new API calls where appropriate. This driver is shared with the Felix DSA switch, so update that at the same time. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-11-07net: remove explicit phylink_generic_validate() referencesRussell King (Oracle)
Virtually all conventional network drivers are now converted to use phylink_generic_validate() - only DSA drivers and fman_memac remain, so lets remove the necessity for network drivers to explicitly set this member, and default to phylink_generic_validate() when unset. This is possible as .validate must currently be set. Any remaining instances that have not been addressed by this patch can be fixed up later. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-29net: enetc: offload per-tc max SDU from tc-taprioVladimir Oltean
The driver currently sets the PTCMSDUR register statically to the max MTU supported by the interface. Keep this logic if tc-taprio is absent or if the max_sdu for a traffic class is 0, and follow the requested max SDU size otherwise. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-20net: enetc: deny offload of tc-based TSN features on VF interfacesVladimir Oltean
TSN features on the ENETC (taprio, cbs, gate, police) are configured through a mix of command BD ring messages and port registers: enetc_port_rd(), enetc_port_wr(). Port registers are a region of the ENETC memory map which are only accessible from the PCIe Physical Function. They are not accessible from the Virtual Functions. Moreover, attempting to access these registers crashes the kernel: $ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001 fsl_enetc_vf 0000:00:01.0: Adding to iommu group 15 fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002) fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0 $ tc qdisc replace dev eno0vf0 root taprio num_tc 8 map 0 1 2 3 4 5 6 7 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \ sched-entry S 0x7f 900000 sched-entry S 0x80 100000 flags 0x2 Unable to handle kernel paging request at virtual address ffff800009551a08 Internal error: Oops: 96000007 [#1] PREEMPT SMP pc : enetc_setup_tc_taprio+0x170/0x47c lr : enetc_setup_tc_taprio+0x16c/0x47c Call trace: enetc_setup_tc_taprio+0x170/0x47c enetc_setup_tc+0x38/0x2dc taprio_change+0x43c/0x970 taprio_init+0x188/0x1e0 qdisc_create+0x114/0x470 tc_modify_qdisc+0x1fc/0x6c0 rtnetlink_rcv_msg+0x12c/0x390 Split enetc_setup_tc() into separate functions for the PF and for the VF drivers. Also remove enetc_qos.o from being included into enetc-vf.ko, since it serves absolutely no purpose there. Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220916133209.3351399-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-20net: enetc: move enetc_set_psfp() out of the common enetc_set_features()Vladimir Oltean
The VF netdev driver shouldn't respond to changes in the NETIF_F_HW_TC flag; only PFs should. Moreover, TSN-specific code should go to enetc_qos.c, which should not be included in the VF driver. Fixes: 79e499829f3f ("net: enetc: add hw tc hw offload features for PSPF capability") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220916133209.3351399-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-12net: enetc: kill PHY-less mode for PFsVladimir Oltean
Right now, a PHY-less port (no phy-mode, no fixed-link, no phy-handle) doesn't register with phylink, but calls netif_carrier_on() from enetc_start(). This makes sense for a VF, but for a PF, this is braindead, because we never call enetc_mac_enable() so the MAC is left inoperational. Furthermore, commit 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX") put the nail in the coffin because it removed the initial netif_carrier_off() call done right after register_netdev(). Without that call, netif_carrier_on() does not call linkwatch_fire_event(), so the operstate remains IF_OPER_UNKNOWN. Just deny the broken configuration by requiring that a phy-mode is present, and always register a PF with phylink. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220511094200.558502-1-vladimir.oltean@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-05-11net: enetc: manage ENETC_F_QBV in priv->active_offloads only when enabledVladimir Oltean
Future work in this driver would like to look at priv->active_offloads & ENETC_F_QBV to determine whether a tc-taprio qdisc offload was installed, but this does not produce the intended effect. All the other flags in priv->active_offloads are managed dynamically, except ENETC_F_QBV which is set statically based on the probed SI capability. This change makes priv->active_offloads & ENETC_F_QBV really track the presence of a tc-taprio schedule on the port. Some existing users, like the enetc_sched_speed_set() call from phylink_mac_link_up(), are best kept using the old logic: the tc-taprio offload does not re-trigger another link mode resolve, so the scheduler needs to be functional from the get go, as long as Qbv is supported at all on the port. So to preserve functionality there, look at the static station interface capability from pf->si->hw_features instead. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-26net: enetc: use .mac_select_pcs() interfaceRussell King (Oracle)
Convert the PCS selection to use mac_select_pcs, which allows the PCS to perform any validation it needs. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-02net: ethernet: enetc: name change for clarity from pcs to mdio_deviceColin Foster
A simple variable update from "pcs" to "mdio_device" for the mdio device will make things a little cleaner. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-02net: phy: lynx: refactor Lynx PCS module to use generic phylink_pcsColin Foster
Remove references to lynx_pcs structures so drivers like the Felix DSA can reference alternate PCS drivers. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17net: enetc: use phylink_generic_validate()Russell King (Oracle)
enetc has no special behaviour in its validation implementation, so can be switched to phylink_generic_validate(). Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17net: enetc: remove interface checks in enetc_pl_mac_validate()Russell King (Oracle)
As phylink checks the interface mode against the supported_interfaces bitmap, we no longer need to validate the interface mode in the validation function. Remove this to simplify it. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17net: enetc: populate supported_interfaces memberRussell King (Oracle)
Populate the phy_interface_t bitmap for the Freescale enetc driver with interfaces modes supported by the MAC. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-24net: convert users of bitmap_foo() to linkmode_foo()Sean Anderson
This converts instances of bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS) to linkmode_foo(args...) I manually fixed up some lines to prevent them from being excessively long. Otherwise, this change was generated with the following semantic patch: // Generated with // echo linux/linkmode.h > includes // git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \ // | sort | uniq | tee new_includes | wc -l && mv new_includes includes // and repeating until the number stopped going up @i@ @@ ( #include <linux/acpi_mdio.h> | #include <linux/brcmphy.h> | #include <linux/dsa/loop.h> | #include <linux/dsa/sja1105.h> | #include <linux/ethtool.h> | #include <linux/ethtool_netlink.h> | #include <linux/fec.h> | #include <linux/fs_enet_pd.h> | #include <linux/fsl/enetc_mdio.h> | #include <linux/fwnode_mdio.h> | #include <linux/linkmode.h> | #include <linux/lsm_audit.h> | #include <linux/mdio-bitbang.h> | #include <linux/mdio.h> | #include <linux/mdio-mux.h> | #include <linux/mii.h> | #include <linux/mii_timestamper.h> | #include <linux/mlx5/accel.h> | #include <linux/mlx5/cq.h> | #include <linux/mlx5/device.h> | #include <linux/mlx5/driver.h> | #include <linux/mlx5/eswitch.h> | #include <linux/mlx5/fs.h> | #include <linux/mlx5/port.h> | #include <linux/mlx5/qp.h> | #include <linux/mlx5/rsc_dump.h> | #include <linux/mlx5/transobj.h> | #include <linux/mlx5/vport.h> | #include <linux/of_mdio.h> | #include <linux/of_net.h> | #include <linux/pcs-lynx.h> | #include <linux/pcs/pcs-xpcs.h> | #include <linux/phy.h> | #include <linux/phy_led_triggers.h> | #include <linux/phylink.h> | #include <linux/platform_data/bcmgenet.h> | #include <linux/platform_data/xilinx-ll-temac.h> | #include <linux/pxa168_eth.h> | #include <linux/qed/qed_eth_if.h> | #include <linux/qed/qed_fcoe_if.h> | #include <linux/qed/qed_if.h> | #include <linux/qed/qed_iov_if.h> | #include <linux/qed/qed_iscsi_if.h> | #include <linux/qed/qed_ll2_if.h> | #include <linux/qed/qed_nvmetcp_if.h> | #include <linux/qed/qed_rdma_if.h> | #include <linux/sfp.h> | #include <linux/sh_eth.h> | #include <linux/smsc911x.h> | #include <linux/soc/nxp/lpc32xx-misc.h> | #include <linux/stmmac.h> | #include <linux/sunrpc/svc_rdma.h> | #include <linux/sxgbe_platform.h> | #include <net/cfg80211.h> | #include <net/dsa.h> | #include <net/mac80211.h> | #include <net/selftests.h> | #include <rdma/ib_addr.h> | #include <rdma/ib_cache.h> | #include <rdma/ib_cm.h> | #include <rdma/ib_hdrs.h> | #include <rdma/ib_mad.h> | #include <rdma/ib_marshall.h> | #include <rdma/ib_pack.h> | #include <rdma/ib_pma.h> | #include <rdma/ib_sa.h> | #include <rdma/ib_smi.h> | #include <rdma/ib_umem.h> | #include <rdma/ib_umem_odp.h> | #include <rdma/ib_verbs.h> | #include <rdma/iw_cm.h> | #include <rdma/mr_pool.h> | #include <rdma/opa_addr.h> | #include <rdma/opa_port_info.h> | #include <rdma/opa_smi.h> | #include <rdma/opa_vnic.h> | #include <rdma/rdma_cm.h> | #include <rdma/rdma_cm_ib.h> | #include <rdma/rdmavt_cq.h> | #include <rdma/rdma_vt.h> | #include <rdma/rdmavt_qp.h> | #include <rdma/rw.h> | #include <rdma/tid_rdma_defs.h> | #include <rdma/uverbs_ioctl.h> | #include <rdma/uverbs_named_ioctl.h> | #include <rdma/uverbs_std_types.h> | #include <rdma/uverbs_types.h> | #include <soc/mscc/ocelot.h> | #include <soc/mscc/ocelot_ptp.h> | #include <soc/mscc/ocelot_vcap.h> | #include <trace/events/ib_mad.h> | #include <trace/events/rdma_core.h> | #include <trace/events/rdma.h> | #include <trace/events/rpcrdma.h> | #include <uapi/linux/ethtool.h> | #include <uapi/linux/ethtool_netlink.h> | #include <uapi/linux/mdio.h> | #include <uapi/linux/mii.h> ) @depends on i@ expression list args; @@ ( - bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_zero(args) | - bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_copy(args) | - bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_and(args) | - bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_or(args) | - bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_empty(args) | - bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_andnot(args) | - bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_equal(args) | - bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_intersects(args) | - bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_subset(args) ) Add missing linux/mii.h include to mellanox. -DaveM Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Lots of simnple overlapping additions. With a build fix from Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-21net: enetc: make sure all traffic classes can send large framesVladimir Oltean
The enetc driver does not implement .ndo_change_mtu, instead it configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU] statically to a large value during probe time. The driver used to configure only the max SDU for traffic class 0, and that was fine while the driver could only use traffic class 0. But with the introduction of mqprio, sending a large frame into any other TC than 0 is broken. This patch fixes that by replicating per traffic class the static configuration done in enetc_configure_port_mac(). Fixes: cbe9e835946f ("enetc: Enable TC offloading with mqprio") Reported-by: Richie Pearn <richard.pearn@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-16ethernet: enetc: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Pass a netdev into the helper instead of just the address, read the address into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: enetc: add support for software TSOIoana Ciornei
This patch adds support for driver level TSO in the enetc driver using the TSO API. Beside using the usual tso_build_hdr(), tso_build_data() this specific implementation also has to compute the checksum, both IP and L4, for each resulted segment. This is because the ENETC controller does not support Tx checksum offload which is needed in order to take advantage of TSO. With the workaround for the ENETC MDIO erratum in place the Tx path of the driver is forced to lock/unlock for each skb sent. This is why, even though we are computing the checksum by hand we see the following improvement in TCP termination on the LS1028A SoC, on a single A72 core running at 1.3GHz: before: 1.63 Gbits/sec after: 2.34 Gbits/sec Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: enetc: declare NETIF_F_HW_CSUM and do it in softwareIoana Ciornei
This is just a preparation patch for software TSO in the enetc driver. Unfortunately, ENETC does not support Tx checksum offload which would normally render TSO, even software, impossible. Declare NETIF_F_HW_CSUM as part of the feature set and do it at driver level using skb_csum_hwoffload_help() so that we can move forward and also add support for TSO in the next patch. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05ethernet: use eth_hw_addr_set() for dev->addr_len casesJakub Kicinski
Convert all Ethernet drivers from memcpy(... dev->addr_len) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, dev->addr_len) + eth_hw_addr_set(dev, np) In theory addr_len may not be ETH_ALEN, but we don't expect non-Ethernet devices to live under this directory, and only the following cases of setting addr_len exist: - cxgb4 for mgmt device, and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
drivers/net/phy/bcm7xxx.c d88fd1b546ff ("net: phy: bcm7xxx: Fixed indirect MMD operations") f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165") net/sched/sch_api.c b193e15ac69d ("net: prevent user from passing illegal stab size") 69508d43334e ("net_sched: Use struct_size() and flex_array_size() helpers") Both cases trivial - adjacent code additions. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-09-24net: enetc: fix the incorrect clearing of IF_MODE bitsVladimir Oltean
The enetc phylink .mac_config handler intends to clear the IFMODE field (bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the other fields instead. For normal operation, the bug was inconsequential, due to the fact that we write the PM0_IF_MODE register in two stages, first in phylink .mac_config (which incorrectly cleared out a bunch of stuff), then we update the speed and duplex to the correct values in phylink .mac_link_up. Judging by the code (not tested), it looks like maybe loopback mode was broken, since this is one of the settings in PM0_IF_MODE which is incorrectly cleared. Fixes: c76a97218dcb ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode") Reported-by: Pavel Machek (CIP) <pavel@denx.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-16net: enetc: Make use of the helper function dev_err_probe()Cai Huoqing
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, and simplify the code. Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27dev_ioctl: split out ndo_eth_ioctlArnd Bergmann
Most users of ndo_do_ioctl are ethernet drivers that implement the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP. Separate these from the few drivers that use ndo_do_ioctl to implement SIOCBOND, SIOCBR and SIOCWANDEV commands. This is a purely cosmetic change intended to help readers find their way through the implementation. Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: linux-rdma@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-04net: enetc: use get/put_unaligned helpers for MAC address handlingMichael Walle
The supplied buffer for the MAC address might not be aligned. Thus doing a 32bit (or 16bit) access could be on an unaligned address. For now, enetc is only used on aarch64 which can do unaligned accesses, thus there is no error. In any case, be correct and use the get/put_unaligned helpers. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-19net: enetc: add support for flow controlVladimir Oltean
In the ENETC receive path, a frame received by the MAC is first stored in a 256KB 'FIFO' memory, then transferred to DRAM when enqueuing it to the RX ring. The FIFO is a shared resource for all ENETC ports, but every port keeps track of its own memory utilization, on RX and on TX. There is a setting for RX rings through which they can either operate in 'lossy' mode (where the lack of a free buffer causes an immediate discard of the frame) or in 'lossless' mode (where the lack of a free buffer in the ring makes the frame stay longer in the FIFO). In turn, when the memory utilization of the FIFO exceeds a certain margin, the MAC can be configured to emit PAUSE frames. There is enough FIFO memory to buffer up to 3 MTU-sized frames per RX port while not jeopardizing the other use cases (jumbo frames), and also not consume bytes from the port TX allocations. Also, 3 MTU-sized frames worth of memory is enough to ensure zero loss for 64 byte packets at 1G line rate. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-19net: enetc: add a mini driver for the Integrated Endpoint Register BlockVladimir Oltean
The NXP ENETC is a 4-port Ethernet controller which 'smells' to operating systems like 4 distinct PCIe PFs with SR-IOV, each PF having its own driver instance, but in fact there are some hardware resources which are shared between all ports, like for example the 256 KB SRAM FIFO between the MACs and the Host Transfer Agent which DMAs frames to DRAM. To hide the stuff that cannot be neatly exposed per port, the hardware designers came up with this idea of having a dedicated register block which is supposed to be populated by the bootloader, and contains everything configuration-related: MAC addresses, FIFO partitioning, etc. When a port is reset using PCIe Function Level Reset, its defaults are transferred from the IERB configuration. Most of the time, the settings made through the IERB are read-only in the port's memory space (if they are even visible), so they cannot be modified at runtime. Linux doesn't have any advanced FIFO partitioning requirements at all, but when reading through the hardware manual, it became clear that, even though there are many good 'recommendations' for default values, many of them were not actually put in practice on LS1028A. So we end up with a default configuration that: (a) does not have enough TX and RX byte credits to support the max MTU of 9600 (which the Linux driver claims already) properly (at full speed) (b) allows the FIFO to be overrun with RX traffic, potentially overwriting internal data structures. The last part sounds a bit catastrophic, but it isn't. Frames are supposed to transit the FIFO for a very short time, but they can actually accumulate there under 2 conditions: (a) there is very severe congestion on DRAM memory, or (b) the RX rings visible to the operating system were configured for lossless operation, and they just ran out of free buffers to copy the frame to. This is what is used to put backpressure onto the MAC with flow control. So since ENETC has not supported flow control thus far, RX FIFO overruns were never seen with Linux. But with the addition of flow control, we should configure some registers to prevent this from happening. What we are trying to protect against are bad actors which continue to send us traffic despite the fact that we have signaled a PAUSE condition. Of course we can't be lossless in that case, but it is best to configure the FIFO to do tail dropping rather than letting it overrun. So in a nutshell, this driver is a fixup for all the IERB default values that should have been but aren't. The IERB configuration needs to be done _before_ the PFs are enabled. So every PF searches for the presence of the "fsl,ls1028a-enetc-ierb" node in the device tree, and if it finds it, it "registers" with the IERB, which means that it requests the IERB to fix up its default values. This is done through -EPROBE_DEFER. The IERB driver is part of the fsl_enetc module, but is technically a platform driver, since the IERB is a good old fashioned MMIO region, as opposed to ENETC ports which pretend to be PCIe devices. The driver was already configuring ENETC_PTXMBAR (FIFO allocation for TX) because due to an omission, TXMBAR is a read/write register in the PF memory space. But the manual is quite clear that the formula for this should depend upon the TX byte credits (TXBCR). In turn, the TX byte credits are only readable/writable through the IERB. So if we want to ensure that the TXBCR register also has a value that is correct and in line with TXMBAR, there is simply no way this can be done from the PF driver, access to the IERB is needed. I could have modified U-Boot to fix up the IERB values, but that is quite undesirable, as old U-Boot versions are likely to be floating around for quite some time from now. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net: enetc: fetch MAC address from device treeMichael Walle
Normally, the bootloader will already initialize the MAC address registers of the ENETC and the driver will just use them or generate a random one, if it is not initialized. Add a new way to provide the MAC address: via device tree. Besides the usual 'mac-address' property, there is also the possibility to fetch it via a NVMEM provider. The sl28 board stores the MAC address in the SPI NOR flash OTP region. Having this will allow linux to fetch the MAC address from there without being dependent on the bootloader. No in-tree boards have the device tree properties set, thus for these, this is a no-op. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-31net: enetc: add support for XDP_REDIRECTVladimir Oltean
The driver implementation of the XDP_REDIRECT action reuses parts from XDP_TX, most notably the enetc_xdp_tx function which transmits an array of TX software BDs. Only this time, the buffers don't have DMA mappings, we need to create them. When a BPF program reaches the XDP_REDIRECT verdict for a frame, we can employ the same buffer reuse strategy as for the normal processing path and for XDP_PASS: we can flip to the other page half and seed that to the RX ring. Note that scatter/gather support is there, but disabled due to lack of multi-buffer support in XDP (which is added by this series): https://patchwork.kernel.org/project/netdevbpf/cover/cover.1616179034.git.lorenzo@kernel.org/ Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-31net: enetc: add support for XDP_DROP and XDP_PASSVladimir Oltean
For the RX ring, enetc uses an allocation scheme based on pages split into two buffers, which is already very efficient in terms of preventing reallocations / maximizing reuse, so I see no reason why I would change that. +--------+--------+--------+--------+--------+--------+--------+ | | | | | | | | | half B | half B | half B | half B | half B | half B | half B | | | | | | | | | +--------+--------+--------+--------+--------+--------+--------+ | | | | | | | | | half A | half A | half A | half A | half A | half A | half A | RX ring | | | | | | | | +--------+--------+--------+--------+--------+--------+--------+ ^ ^ | | next_to_clean next_to_alloc next_to_use +--------+--------+--------+--------+--------+ | | | | | | | half B | half B | half B | half B | half B | | | | | | | +--------+--------+--------+--------+--------+--------+--------+ | | | | | | | | | half B | half B | half A | half A | half A | half A | half A | RX ring | | | | | | | | +--------+--------+--------+--------+--------+--------+--------+ | | | ^ ^ | half A | half A | | | | | | next_to_clean next_to_use +--------+--------+ ^ | next_to_alloc then when enetc_refill_rx_ring is called, whose purpose is to advance next_to_use, it sees that it can take buffers up to next_to_alloc, and it says "oh, hey, rx_swbd->page isn't NULL, I don't need to allocate one!". The only problem is that for default PAGE_SIZE values of 4096, buffer sizes are 2048 bytes. While this is enough for normal skb allocations at an MTU of 1500 bytes, for XDP it isn't, because the XDP headroom is 256 bytes, and including skb_shared_info and alignment, we end up being able to make use of only 1472 bytes, which is insufficient for the default MTU. To solve that problem, we implement scatter/gather processing in the driver, because we would really like to keep the existing allocation scheme. A packet of 1500 bytes is received in a buffer of 1472 bytes and another one of 28 bytes. Because the headroom required by XDP is different (and much larger) than the one required by the network stack, whenever a BPF program is added or deleted on the port, we drain the existing RX buffers and seed new ones with the required headroom. We also keep the required headroom in rx_ring->buffer_offset. The simplest way to implement XDP_PASS, where an skb must be created, is to create an xdp_buff based on the next_to_clean RX BDs, but not clear those BDs from the RX ring yet, just keep the original index at which the BDs for this frame started. Then, if the verdict is XDP_PASS, instead of converting the xdb_buff to an skb, we replay a call to enetc_build_skb (just as in the normal enetc_clean_rx_ring case), starting from the original BD index. We would also like to be minimally invasive to the regular RX data path, and not check whether there is a BPF program attached to the ring on every packet. So we create a separate RX ring processing function for XDP. Because we only install/remove the BPF program while the interface is down, we forgo the rcu_read_lock() in enetc_clean_rx_ring, since there shouldn't be any circumstance in which we are processing packets and there is a potentially freed BPF program attached to the RX ring. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: enetc: don't depend on system endianness in enetc_set_mac_ht_fltVladimir Oltean
When enetc runs out of exact match entries for unicast address filtering, it switches to an approach based on hash tables, where multiple MAC addresses might end up in the same bucket. However, the enetc_set_mac_ht_flt function currently depends on the system endianness, because it interprets the 64-bit hash value as an array of two u32 elements. Modify this to use lower_32_bits and upper_32_bits. Tested by forcing enetc to go into hash table mode by creating two macvlan upper interfaces: ip link add link eno0 address 00:01:02:03:00:00 eno0.0 type macvlan && ip link set eno0.0 up ip link add link eno0 address 00:01:02:03:00:01 eno0.1 type macvlan && ip link set eno0.1 up and verified that the same bit values are written to the registers before and after: enetc_sync_mac_filters: addr 00:00:80:00:40:10 exact match 0 enetc_sync_mac_filters: addr 00:00:00:00:80:00 exact match 0 enetc_set_mac_ht_flt: hash 0x80008000000000 UMHFR0 0x0 UMHFR1 0x800080 Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: enetc: don't depend on system endianness in enetc_set_vlan_ht_filterVladimir Oltean
ENETC has a 64-entry hash table for VLAN RX filtering per Station Interface, which is accessed through two 32-bit registers: VHFR0 holding the low portion, and VHFR1 holding the high portion. The enetc_set_vlan_ht_filter function looks at the pf->vlan_ht_filter bitmap, which is fundamentally an unsigned long variable, and casts it to a u32 array of two elements. It puts the first u32 element into VHFR0 and the second u32 element into VHFR1. It is easy to imagine that this will not work on big endian systems (although, yes, we have bigger problems, because currently enetc assumes that the CPU endianness is equal to the controller endianness, aka little endian - but let's assume that we could add a cpu_to_le32 in enetc_wd_reg and a le32_to_cpu in enetc_rd_reg). Let's use lower_32_bits and upper_32_bits which are designed to work regardless of endianness. Tested that both the old and the new method produce the same results: $ ethtool -K eth1 rx-vlan-filter on $ ip link add link eth1 name eth1.100 type vlan id 100 enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x0 VHFR1 0x20 enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x0 VHFR1 0x20 $ ip link add link eth1 name eth1.101 type vlan id 101 enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x0 VHFR1 0x30 enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x0 VHFR1 0x30 $ ip link add link eth1 name eth1.34 type vlan id 34 enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x0 VHFR1 0x34 enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x0 VHFR1 0x34 $ ip link add link eth1 name eth1.1024 type vlan id 1024 enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x1 VHFR1 0x34 enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x1 VHFR1 0x34 Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-19net: enetc: teardown CBDR during PF/VF unbindVladimir Oltean
Michael reports that after the blamed patch, unbinding a VF would cause these transactions to remain pending, and trigger some warnings with the DMA API debug: $ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001 fsl_enetc_vf 0000:00:01.0: Adding to iommu group 19 fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002) fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0 $ echo 0 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs DMA-API: pci 0000:00:01.0: device driver has pending DMA allocations while released from device [count=1] One of leaked entries details: [size=2048 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent] WARNING: CPU: 0 PID: 2547 at kernel/dma/debug.c:853 dma_debug_device_change+0x174/0x1c8 (...) Call trace: dma_debug_device_change+0x174/0x1c8 blocking_notifier_call_chain+0x74/0xa8 device_release_driver_internal+0x18c/0x1f0 device_release_driver+0x20/0x30 pci_stop_bus_device+0x8c/0xe8 pci_stop_and_remove_bus_device+0x20/0x38 pci_iov_remove_virtfn+0xb8/0x128 sriov_disable+0x3c/0x110 pci_disable_sriov+0x24/0x30 enetc_sriov_configure+0x4c/0x108 sriov_numvfs_store+0x11c/0x198 (...) DMA-API: Mapped at: dma_entry_alloc+0xa4/0x130 debug_dma_alloc_coherent+0xbc/0x138 dma_alloc_attrs+0xa4/0x108 enetc_setup_cbdr+0x4c/0x1d0 enetc_vf_probe+0x11c/0x250 pci 0000:00:01.0: Removing from iommu group 19 This happens because stupid me moved enetc_teardown_cbdr outside of enetc_free_si_resources, but did not bother to keep calling enetc_teardown_cbdr from all the places where enetc_free_si_resources was called. In particular, now it is no longer called from the main unbind function, just from the probe error path. Fixes: 4b47c0b81ffd ("net: enetc: don't initialize unused ports from a separate code path") Reported-by: Michael Walle <michael@walle.cc> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10net: enetc: don't initialize unused ports from a separate code pathVladimir Oltean
Since commit 3222b5b613db ("net: enetc: initialize RFS/RSS memories for unused ports too") there is a requirement to initialize the memories of unused PFs too, which has left the probe path in a bit of a rough shape, because we basically have a minimal initialization path for unused PFs which is separate from the main initialization path. Now that initializing a control BD ring is as simple as calling enetc_setup_cbdr, let's move that outside of enetc_alloc_si_resources (unused PFs don't need classification rules, so no point in allocating them just to free them later). But enetc_alloc_si_resources is called both for PFs and for VFs, so now that enetc_setup_cbdr is no longer called from this common function, it means that the VF probe path needs to explicitly call enetc_setup_cbdr too. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10net: enetc: pass bd_count as an argument to enetc_setup_cbdrVladimir Oltean
It makes no sense from an API perspective to first initialize some portion of struct enetc_cbdr outside enetc_setup_cbdr, then leave that function to initialize the rest. enetc_setup_cbdr should be able to perform all initialization given a zero-initialized struct enetc_cbdr. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10net: enetc: squash clear_cbdr and free_cbdr into teardown_cbdrVladimir Oltean
All call sites call enetc_clear_cbdr and enetc_free_cbdr one after another, so let's combine the two functions into a single method named enetc_teardown_cbdr which does both, and in the same order. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10net: enetc: save the mode register address inside struct enetc_cbdrVladimir Oltean
enetc_clear_cbdr depends on struct enetc_hw because it must disable the ring through a register write. We'd like to remove that dependency, so let's do what's already done with the producer and consumer indices, which is to save the iomem address in a variable kept in struct enetc_cbdr. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10net: enetc: squash enetc_alloc_cbdr and enetc_setup_cbdrVladimir Oltean
enetc_alloc_cbdr and enetc_setup_cbdr are always called one after another, so we can simplify the callers and make enetc_setup_cbdr do everything that's needed. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-10net: enetc: save the DMA device for enetc_free_cbdrVladimir Oltean
We shouldn't need to pass the struct device *dev to enetc CBDR APIs over and over again, so save this inside struct enetc_cbdr::dma_dev and avoid calling it from the enetc_free_cbdr functions. This breaks the dependency of the cbdr API from struct enetc_si (the station interface). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2024-06-14 06:07:06 +0000