| Age | Commit message (Collapse) | Author |
|---|
|
When repeatedly changing the interface link speed using the command below:
ethtool -s eth0 speed 100 duplex full
ethtool -s eth0 speed 1000 duplex full
The following errors may sometimes be reported by the ARM SMMU driver:
[ 5395.035364] fec 5b040000.ethernet eth0: Link is Down
[ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault:
fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2
[ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
It is identified that the FEC driver does not properly stop the TX queue
during the link speed transitions, and this results in the invalid virtual
I/O address translations from the SMMU and causes the context faults.
Fixes: dbc64a8ea231 ("net: fec: move calls to quiesce/resume packet processing out of fec_restart()")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20240123165141.2008104-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the FEC (MPC8xx) Ethernet controller.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240123190332.677489-8-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/intel/iavf/iavf_ethtool.c
3a0b5a2929fd ("iavf: Introduce new state machines for flow director")
95260816b489 ("iavf: use iavf_schedule_aq_request() helper")
https://lore.kernel.org/all/84e12519-04dc-bd80-bc34-8cf50d7898ce@intel.com/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
c13e268c0768 ("bnxt_en: Fix HWTSTAMP_FILTER_ALL packet timestamp logic")
c2f8063309da ("bnxt_en: Refactor RX VLAN acceleration logic.")
a7445d69809f ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
1c7fd6ee2fe4 ("bnxt_en: Rename some macros for the P5 chips")
https://lore.kernel.org/all/20231211110022.27926ad9@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
bd6781c18cb5 ("bnxt_en: Fix wrong return value check in bnxt_close_nic()")
84793a499578 ("bnxt_en: Skip nic close/open when configuring tstamp filters")
https://lore.kernel.org/all/20231214113041.3a0c003c@canb.auug.org.au/
drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c
3d7a3f2612d7 ("net/mlx5: Nack sync reset request when HotPlug is enabled")
cecf44ea1a1f ("net/mlx5: Allow sync reset flow when BF MGT interface device is present")
https://lore.kernel.org/all/20231211110328.76c925af@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The old implementation extracted VLAN TCI info from the payload
before the VLAN tag has been pushed in the payload.
Another problem was that the VLAN TCI was extracted even if the
packet did not have VLAN protocol header.
This resulted in invalid VLAN TCI and as a consequence a random
queue was computed.
This patch fixes the above issues and use the VLAN TCI from the
skb if it is present or VLAN TCI from payload if present. If no
VLAN header is present queue 0 is selected.
Fixes: 52c4a1a85f4b ("net: fec: add ndo_select_queue to fix TX bandwidth fluctuations")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- get rid of the fake support for coherent DMA allocation on coldfire
with caches (Christoph Hellwig)
- add a few Kconfig dependencies so that Kconfig catches the use of
invalid configurations (Christoph Hellwig)
- fix a type in dma-debug output (Chuck Lever)
- rewrite a comment in swiotlb (Sean Christopherson)
* tag 'dma-mapping-6.7-2023-10-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: Fix a typo in a debugging eye-catcher
swiotlb: rewrite comment explaining why the source is preserved on DMA_FROM_DEVICE
m68k: remove unused includes from dma.c
m68k: don't provide arch_dma_alloc for nommu/coldfire
net: fec: use dma_alloc_noncoherent for data cache enabled coldfire
m68k: use the coherent DMA code for coldfire without data cache
dma-direct: warn when coherent allocations aren't supported
dma-direct: simplify the use atomic pool logic in dma_direct_alloc
dma-direct: add a CONFIG_ARCH_HAS_DMA_ALLOC symbol
dma-direct: add dependencies to CONFIG_DMA_GLOBAL_POOL
|
|
Coldfire platforms with data caches can't properly implement
dma_alloc_coherent and currently just return noncoherent memory from
dma_alloc_coherent.
The fec driver than works around this with a flush of all caches in the
receive path. Make this hack a little less bad by using the explicit
dma_alloc_noncoherent API and documenting the hacky cache flushes so
that the DMA API level hack can be removed.
Also replace the check for CONFIG_M532x for said hack with a check
for COLDFIRE && !COLDFIRE_COHERENT_DMA. While m532x is the only such
platform with a fec module, this makes the code more consistent and
easier to follow.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
|
|
All i.MX platforms (non-Coldfire) use DT nowadays, so their platform ID
entries can be removed.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231017063419.925266-3-alexander.stein@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
device_get_match_data() expects that of_device_id->data points to actual
fec_devinfo data, not a platform_device_id entry.
Fix this by adjusting OF device data pointers to their corresponding
structs.
enum imx_fec_type is now unused and can be removed.
Fixes: b0377116decd ("net: ethernet: Use device_get_match_data()")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231017063419.925266-2-alexander.stein@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
ethtool_sprintf() is designed specifically for get_strings() usage.
Let's replace strncpy in favor of this more robust and easier to
understand interface.
Also, while we're here, let's change memcpy() over to ethtool_sprintf()
for consistency.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xdp_do_flush_map() is deprecated and new code should use xdp_do_flush()
instead.
Replace xdp_do_flush_map() with xdp_do_flush().
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: John Crispin <john@phrozen.org>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Cc: Shenwei Wang <shenwei.wang@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230908143215.869913-2-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The FEC driver supports the statistics for XDP actions except for
XDP_TX before, because the XDP_TX was not supported when adding
the statistics for XDP. Now the FEC driver has supported XDP_TX
since commit f601899e4321 ("net: fec: add XDP_TX feature support").
So it's reasonable and necessary to add statistics for XDP_TX.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we already added the exception tracing for XDP_TX, I think it is
necessary to add the exception tracing for other XDP actions, such
as XDP_REDIRECT, XDP_ABORTED and unknown error actions.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230822065255.606739-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the "budget" is passed into fec_enet_tx_queue(), one
optimization we can do is to use napi_consume_skb() to instead
of dev_kfree_skb_any().
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Alexander H Duyck <alexander.duyck@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230816090242.463822-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As suggested by Jesper and Alexander, we can avoid converting xdp_buff
to xdp_frame in case of XDP_TX to save a bunch of CPU cycles, so that
we can further improve the XDP_TX performance.
Before this patch on i.MX8MP-EVK board, the performance shows as follows.
root@imx8mpevk:~# ./xdp2 eth0
proto 17: 353918 pkt/s
proto 17: 352923 pkt/s
proto 17: 353900 pkt/s
proto 17: 352672 pkt/s
proto 17: 353912 pkt/s
proto 17: 354219 pkt/s
After applying this patch, the performance is improved.
root@imx8mpevk:~# ./xdp2 eth0
proto 17: 369261 pkt/s
proto 17: 369267 pkt/s
proto 17: 369206 pkt/s
proto 17: 369214 pkt/s
proto 17: 369126 pkt/s
proto 17: 369272 pkt/s
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Suggested-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The XDP_TX feature is not supported before, and all the frames
which are deemed to do XDP_TX action actually do the XDP_DROP
action. So this patch adds the XDP_TX support to FEC driver.
I tested the performance of XDP_TX in XDP_DRV mode and XDP_SKB
mode respectively on i.MX8MP-EVK platform, and as suggested by
Jesper, I also tested the performance of XDP_REDIRECT on the
same platform. And the test steps and results are as follows.
XDP_TX test:
Step 1: One board is used as generator and connects to switch,and
the FEC port of DUT also connects to the switch. Both boards with
flow control off. Then the generator runs the
pktgen_sample03_burst_single_flow.sh script to generate and send
burst traffic to DUT. Note that the size of packet was set to 64
bytes and the procotol of packet was UDP in my test scenario. In
addition, the SMAC of the packet need to be different from the MAC
of the generator, because the xdp2 program will swap the DMAC and
SMAC of the packet and send it back to the generator. If the SMAC
of the generated packet is the MAC of the generator, the generator
will receive the returned traffic which increase the CPU loading
and significantly degrade the transmit speed of the generator, and
finally it affects the test of XDP_TX performance.
Step 2: The DUT runs the xdp2 program to transmit received UDP
packets back out on the same port where they were received.
root@imx8mpevk:~# ./xdp2 eth0
proto 17: 353918 pkt/s
proto 17: 352923 pkt/s
proto 17: 353900 pkt/s
proto 17: 352672 pkt/s
proto 17: 353912 pkt/s
proto 17: 354219 pkt/s
root@imx8mpevk:~# ./xdp2 -S eth0
proto 17: 160604 pkt/s
proto 17: 160708 pkt/s
proto 17: 160564 pkt/s
proto 17: 160684 pkt/s
proto 17: 160640 pkt/s
proto 17: 160720 pkt/s
The above results show that the XDP_TX performance of XDP_DRV mode
is much better than XDP_SKB mode, more than twice that of XDP_SKB
mode, which is in line with our expectation.
XDP_REDIRECT test:
Step1: Both the generator and the FEC port of the DUT connet to the
switch port. All the ports with flow control off, then the generator
runs the pktgen script to generate and send burst traffic to DUT.
Note that the size of packet was set to 64 bytes and the procotol of
packet was UDP in my test scenario.
Step2: The DUT runs the xdp_redirect program to redirect the traffic
from the FEC port to the FEC port itself.
root@imx8mpevk:~# ./xdp_redirect eth0 eth0
Redirecting from eth0 (ifindex 2; driver fec) to eth0
(ifindex 2; driver fec)
Summary 232,302 rx/s 0 err,drop/s 232,344 xmit/s
Summary 234,579 rx/s 0 err,drop/s 234,577 xmit/s
Summary 235,548 rx/s 0 err,drop/s 235,549 xmit/s
Summary 234,704 rx/s 0 err,drop/s 234,703 xmit/s
Summary 235,504 rx/s 0 err,drop/s 235,504 xmit/s
Summary 235,223 rx/s 0 err,drop/s 235,224 xmit/s
Summary 234,509 rx/s 0 err,drop/s 234,507 xmit/s
Summary 235,481 rx/s 0 err,drop/s 235,482 xmit/s
Summary 234,684 rx/s 0 err,drop/s 234,683 xmit/s
Summary 235,520 rx/s 0 err,drop/s 235,520 xmit/s
Summary 235,461 rx/s 0 err,drop/s 235,461 xmit/s
Summary 234,627 rx/s 0 err,drop/s 234,627 xmit/s
Summary 235,611 rx/s 0 err,drop/s 235,611 xmit/s
Packets received : 3,053,753
Average packets/s : 234,904
Packets transmitted : 3,053,792
Average transmit/s : 234,907
Compared the performance of XDP_TX with XDP_REDIRECT, XDP_TX is also
much better than XDP_REDIRECT. It's also in line with our expectation.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Jesper Dangaard Brouer <hawk@kernel.org>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split types and pure function declarations from page_pool.h
and add them in page_page/types.h, so that C sources can
include page_pool.h and headers should generally only include
page_pool/types.h as suggested by jakub.
Rename page_pool.h to page_pool/helpers.h to have both in
one place.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230804180529.2483231-2-aleksander.lobakin@intel.com
[Jakub: change microsoft/mana, fix kdoc paths in Documentation]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers
It is desirable that the new .ndo_hwtstamp_set() API gives more
uniformity, less overhead and future flexibility w.r.t. the PHY
timestamping behavior.
Currently there are some drivers which allow PHY timestamping through
the procedure mentioned in Documentation/networking/timestamping.rst.
They don't do anything locally if phy_has_hwtstamp() is set, except for
lan966x which installs PTP packet traps.
Centralize that behavior in a new dev_set_hwtstamp_phylib() code
function, which calls either phy_mii_ioctl() for the phylib PHY,
or .ndo_hwtstamp_set() of the netdev, based on a single policy
(currently simplistic: phy_has_hwtstamp()).
Any driver converted to .ndo_hwtstamp_set() will automatically opt into
the centralized phylib timestamping policy. Unconverted drivers still
get to choose whether they let the PHY handle timestamping or not.
Netdev drivers with integrated PHY drivers that don't use phylib
presumably don't set dev->phydev, and those will always see
HWTSTAMP_SOURCE_NETDEV requests even when converted. The timestamping
policy will remain 100% up to them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-13-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 340746398b67 ("net: fec: fix hardware time stamping by external
devices") was overly cautious with calling fec_ptp_disable_hwts() when
cmd == SIOCSHWTSTAMP and use_fec_hwts == false, because use_fec_hwts is
based on a runtime invariant (phy_has_hwtstamp()). Thus, if use_fec_hwts
is false, then fep->hwts_tx_en and fep->hwts_rx_en cannot be changed at
runtime; their values depend on the initial memory allocation, which
already sets them to zeroes.
If the core will ever gain support for switching timestamping layers,
it will arrange for a more organized calling convention and disable
timestamping in the previous layer as a first step. This means that the
code in the FEC driver is not necessary in any case.
The purpose of this change is to arrange the phy_has_hwtstamp() code in
a way in which it can be refactored away into generic logic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-8-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hardware timestamping through ndo_eth_ioctl() is going away.
Convert the FEC driver to the new API before that can be removed.
After removing the timestamping logic from fec_enet_ioctl(), the rest
is equivalent to phy_do_ioctl_running().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the clarification [1] in the latest napi.rst, the tx
processing cannot call any XDP (or page pool) APIs if the "budget"
is 0. Because NAPI is called with the budget of 0 (such as netpoll)
indicates we may be in an IRQ context, however, we cannot use the
page pool from IRQ context.
[1] https://lore.kernel.org/all/20230720161323.2025379-1-kuba@kernel.org/
Fixes: 20f797399035 ("net: fec: recycle pages for transmitted XDP frames")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230725074148.2936402-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the implementation of XDP of FEC driver, the XDP path
shares the transmit queues with the kernel network stack, so it is
possible to lead to a tx timeout event when XDP uses the tx queue
pretty much exclusively. And this event will cause the reset of the
FEC hardware.
To avoid timeout in this case, we use the txq_trans_cond_update()
interface to update txq->trans_start to jiffies so that watchdog
won't generate a transmit timeout warning.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230721083559.2857312-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fec_enet_init() is only invoked when the FEC driver probes, and
the network device of FEC is not been brought up at this moment. So
the fec_set_mac_address() does nothing and just returns zero when it
is invoked in the fec_enet_init(). Actually, the MAC address is set
into the hardware through fec_restart() which is also called in the
fec_enet_init().
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230718090928.2654347-3-wei.fang@nxp.com
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the commit 95698ff6177b ("net: fec: using page pool to manage
RX buffers") has been applied, all the rx packets, no matter small
packets or large packets are put directly into the kernel networking
buffers. That is to say, the rx copybreak function has been removed
since then, but the related code has not been completely cleaned up.
So the purpose of this patch is to clean up the remaining related
code of rx copybreak.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230718090928.2654347-2-wei.fang@nxp.com
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230710071946.3470249-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the case of heavy XDP traffic to be transmitted, the console
will print the error log continuously if there are lack of enough
BDs to accommodate the frames. The log looks like below.
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
Not only will this log be replicated and redundant, it will also
degrade XDP performance. So we use netdev_err_once() instead of
netdev_err() now.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the XDP feature is enabled and with heavy XDP frames to be
transmitted, there is a considerable probability that available
tx BDs are insufficient. This will lead to some XDP frames to be
discarded and the "NOT enough BD for SG!" error log will appear
in the console (as shown below).
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
In the case of heavy XDP traffic, sometimes the speed of recycling
tx BDs may be slower than the speed of sending XDP frames. There
may be several specific reasons, such as the interrupt is not
responsed in time, the efficiency of the NAPI callback function is
too low due to all the queues (tx queues and rx queues) share the
same NAPI, and so on.
After trying various methods, I think that increase the size of tx
BD ring is simple and effective. Maybe the best resolution is that
allocate NAPI for each queue to improve the efficiency of the NAPI
callback, but this change is a bit big and I didn't try this method.
Perheps this method will be implemented in a future patch.
This patch also updates the tx_wake_threshold of tx ring which is
related to the size of tx ring in the previous logic. Otherwise,
the tx_wake_threshold will be too high (403 BDs), which is more
likely to impact the slow path in the case of heavy XDP traffic,
because XDP path and slow path share the tx BD rings. According
to Jakub's suggestion, the tx_wake_threshold is at least equal to
tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of
entries is overflowing, we should be able to apply a hysteresis
of a few tens of entries.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Once the XDP frames have been successfully transmitted through the
ndo_xdp_xmit() interface, it's the driver responsibility to free
the frames so that the page_pool can recycle the pages and reuse
them. However, this action is not implemented in the fec driver.
This leads to a user-visible problem that the console will print
the following warning log.
[ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec
[ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec
[ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec
[ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec
[ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec
Therefore, to solve this issue, we free XDP frames via xdp_return_frame()
while cleaning the tx BD ring.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a XDP program is installed or uninstalled, fec_restart() will
be invoked to reset MAC and buffer descriptor rings. It's reasonable
not to transmit any packet during the process of reset. However, the
NETDEV_XDP_ACT_NDO_XMIT bit of xdp_features is enabled by default,
that is to say, it's possible that the fec_enet_xdp_xmit() will be
invoked even if the process of reset is not finished. In this case,
the redirected XDP frames might be dropped and available transmit BDs
may be incorrectly deemed insufficient. So this patch disable the
NETDEV_XDP_ACT_NDO_XMIT feature by default and dynamically configure
this feature when the bpf program is installed or uninstalled.
Fixes: e4ac7cc6e5a4 ("net: fec: turn on XDP features")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 6970ef27ff7f ("net: fec: add xdp and page pool statistics") selected
CONFIG_PAGE_POOL_STATS from the FEC driver symbol, making it impossible
to build without the page pool statistics when this driver is enabled. The
help text of those statistics mentions increased overhead. Allow the user
to choose between usefulness of the statistics and the added overhead.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230616191832.2944130-1-l.stach@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The last_bdp is initialized to bdp, and both last_bdp and bdp are
not changed. That is to say that last_bdp and bdp are always equal.
So bdp can be used directly.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230529022615.669589-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/raw.c
3632679d9e4f ("ipv{4,6}/raw: fix output xfrm lookup wrt protocol")
c85be08fc4fa ("raw: Stop using RTO_ONLINK.")
https://lore.kernel.org/all/20230525110037.2b532b83@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/freescale/fec_main.c
9025944fddfe ("net: fec: add dma_wmb to ensure correct descriptor values")
144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch is a cleanup for fec driver. The fec_enet_reset_skb()
is used to free skb buffers for tx queues and is only invoked in
fec_restart(). However, fec_enet_bd_init() also resets skb buffers
and is invoked in fec_restart() too. So fec_enet_reset_skb() is
redundant and useless.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The XDP features are supported since the commit 66c0e13ad236
("drivers: net: turn on XDP features"). Currently, the fec
driver supports NETDEV_XDP_ACT_BASIC, NETDEV_XDP_ACT_REDIRECT
and NETDEV_XDP_ACT_NDO_XMIT. So turn on these XDP features
for fec driver.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two dma_wmb() are added in the XDP TX path to ensure proper ordering of
descriptor and buffer updates:
1. A dma_wmb() is added after updating the last BD to make sure
the updates to rest of the descriptor are visible before
transferring ownership to FEC.
2. A dma_wmb() is also added after updating the bdp to ensure these
updates are visible before updating txq->bd.cur.
3. Start the xmit of the frame immediately right after configuring the
tx descriptor.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98cafc ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the implementation, the sent_frame count does not increment when
transmit errors occur. Therefore, bq_xmit_all() will take care of
returning the XDP frames.
Fixes: 26312c685ae0 ("net: fec: correct the counting of XDP sent frames")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch standardizes the inconsistent return values for unsuccessful
XDP transmits by using standardized error codes (-EBUSY or -ENOMEM).
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba21 ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the current xdp_xmit implementation, if any single frame fails to
transmit due to insufficient buffer descriptors, the function nevertheless
reports success in sending all frames. This results in erroneously
indicating that frames were transmitted when in fact they were dropped.
This patch fixes the issue by ensureing the return value properly
indicates the actual number of frames successfully transmitted, rather than
potentially reporting success for all frames when some could not transmit.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all fec MDIO bus drivers support C45 mode transactions. The older fec
hardware block in many ColdFire SoCs does not appear to support them, at
least according to most of the different ColdFire SoC reference manuals.
The bits used to generate C45 access on the iMX parts, in the OP field
of the MMFR register, are documented as generating non-compliant MII
frames (it is not documented as to exactly how they are non-compliant).
Commit 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
means the fec driver will always register c45 MDIO read and write
methods. During probe these will always be accessed now generating
non-compliant MII accesses on ColdFire based devices.
Add a quirk define, FEC_QUIRK_HAS_MDIO_C45, that can be used to
distinguish silicon that supports MDIO C45 framing or not. Add this to
all the existing iMX quirks, so they will be behave as they do now (*).
(*) it seems that some iMX parts may not support C45 transactions either.
The iMX25 and iMX50 Reference Manuals contain similar wording to
the ColdFire Reference Manuals on this.
Fixes: 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230404052207.3064861-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conversion to gpiod API done in commit 468ba54bd616 ("fec: convert
to gpio descriptor") clashed with gpiolib applying the same quirk to the
reset GPIO polarity (introduced in commit b02c85c9458c). This results in
the reset line being left active/device being left in reset state when
reset line is "active low".
Remove handling of 'phy-reset-active-high' property from the driver and
rely on gpiolib to apply needed adjustments to avoid ending up with the
double inversion/flipped logic.
Fixes: 468ba54bd616 ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230201215320.528319-2-dmitry.torokhov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conversion of the driver to gpiod API done in 468ba54bd616 ("fec:
convert to gpio descriptor") incorrectly made reset line mandatory and
resulted in aborting driver probe in cases where reset line was not
specified (note: this way of specifying PHY reset line is actually
deprecated).
Switch to using devm_gpiod_get_optional() and skip manipulating reset
line if it can not be located.
Fixes: 468ba54bd616 ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230201215320.528319-1-dmitry.torokhov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver can be trivially converted, as it only triggers the gpio
pin briefly to do a reset, and it already only supports DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/ice/ice_main.c
418e53401e47 ("ice: move devlink port creation/deletion")
643ef23bd9dd ("ice: Introduce local var for readability")
https://lore.kernel.org/all/20230127124025.0dacef40@canb.auug.org.au/
https://lore.kernel.org/all/20230124005714.3996270-1-anthony.l.nguyen@intel.com/
drivers/net/ethernet/engleder/tsnep_main.c
3d53aaef4332 ("tsnep: Fix TX queue stop/wake for multiple queues")
25faa6a4c5ca ("tsnep: Replace TX spin_lock with __netif_tx_lock")
https://lore.kernel.org/all/20230127123604.36bb3e99@canb.auug.org.au/
net/netfilter/nf_conntrack_proto_sctp.c
13bd9b31a969 ("Revert "netfilter: conntrack: add sctp DATA_SENT state"")
a44b7651489f ("netfilter: conntrack: unify established states for SCTP paths")
f71cb8f45d09 ("netfilter: conntrack: sctp: use nf log infrastructure for invalid packets")
https://lore.kernel.org/all/20230127125052.674281f9@canb.auug.org.au/
https://lore.kernel.org/all/d36076f3-6add-a442-6d4b-ead9f7ffff86@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The page_pool_release_page was used when freeing rx buffers, and this
function just unmaps the page (if mapped) and does not recycle the page.
So after hundreds of down/up the eth0, the system will out of memory.
For more details, please refer to the following reproduce steps and
bug logs. To solve this issue and refer to the doc of page pool, the
page_pool_put_full_page should be used to replace page_pool_release_page.
Because this API will try to recycle the page if the page refcnt equal to
1. After testing 20000 times, the issue can not be reproduced anymore
(about testing 391 times the issue will occur on i.MX8MN-EVK before).
Reproduce steps:
Create the test script and run the script. The script content is as
follows:
LOOPS=20000
i=1
while [ $i -le $LOOPS ]
do
echo "TINFO:ENET $curface up and down test $i times"
org_macaddr=$(cat /sys/class/net/eth0/address)
ifconfig eth0 down
ifconfig eth0 hw ether $org_macaddr up
i=$(expr $i + 1)
done
sleep 5
if cat /sys/class/net/eth0/operstate | grep 'up';then
echo "TEST PASS"
else
echo "TEST FAIL"
fi
Bug detail logs:
TINFO:ENET up and down test 391 times
[ 850.471205] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 853.535318] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 853.541694] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 870.590531] page_pool_release_retry() stalled pool shutdown 199 inflight 60 sec
[ 931.006557] page_pool_release_retry() stalled pool shutdown 199 inflight 120 sec
TINFO:ENET up and down test 392 times
[ 991.426544] page_pool_release_retry() stalled pool shutdown 192 inflight 181 sec
[ 1051.838531] page_pool_release_retry() stalled pool shutdown 170 inflight 241 sec
[ 1093.751217] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 1096.446520] page_pool_release_retry() stalled pool shutdown 308 inflight 60 sec
[ 1096.831245] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1096.839092] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1112.254526] page_pool_release_retry() stalled pool shutdown 103 inflight 302 sec
[ 1156.862533] page_pool_release_retry() stalled pool shutdown 308 inflight 120 sec
[ 1172.674516] page_pool_release_retry() stalled pool shutdown 103 inflight 362 sec
[ 1217.278532] page_pool_release_retry() stalled pool shutdown 308 inflight 181 sec
TINFO:ENET up and down test 393 times
[ 1233.086535] page_pool_release_retry() stalled pool shutdown 103 inflight 422 sec
[ 1277.698513] page_pool_release_retry() stalled pool shutdown 308 inflight 241 sec
[ 1293.502525] page_pool_release_retry() stalled pool shutdown 86 inflight 483 sec
[ 1338.110518] page_pool_release_retry() stalled pool shutdown 308 inflight 302 sec
[ 1353.918540] page_pool_release_retry() stalled pool shutdown 32 inflight 543 sec
[ 1361.179205] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 1364.255298] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1364.263189] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1371.998532] page_pool_release_retry() stalled pool shutdown 310 inflight 60 sec
[ 1398.530542] page_pool_release_retry() stalled pool shutdown 308 inflight 362 sec
[ 1414.334539] page_pool_release_retry() stalled pool shutdown 16 inflight 604 sec
[ 1432.414520] page_pool_release_retry() stalled pool shutdown 310 inflight 120 sec
[ 1458.942523] page_pool_release_retry() stalled pool shutdown 308 inflight 422 sec
[ 1474.750521] page_pool_release_retry() stalled pool shutdown 16 inflight 664 sec
TINFO:ENET up and down test 394 times
[ 1492.830522] page_pool_release_retry() stalled pool shutdown 310 inflight 181 sec
[ 1519.358519] page_pool_release_retry() stalled pool shutdown 308 inflight 483 sec
[ 1535.166545] page_pool_release_retry() stalled pool shutdown 2 inflight 724 sec
[ 1537.090278] eth_test2.sh invoked oom-killer: gfp_mask=0x400dc0(GFP_KERNEL_ACCOUNT|__GFP_ZERO), order=0, oom_score_adj=0
[ 1537.101192] CPU: 3 PID: 2379 Comm: eth_test2.sh Tainted: G C 6.1.1+g56321e101aca #1
[ 1537.110249] Hardware name: NXP i.MX8MNano EVK board (DT)
[ 1537.115561] Call trace:
[ 1537.118005] dump_backtrace.part.0+0xe0/0xf0
[ 1537.122289] show_stack+0x18/0x40
[ 1537.125608] dump_stack_lvl+0x64/0x80
[ 1537.129276] dump_stack+0x18/0x34
[ 1537.132592] dump_header+0x44/0x208
[ 1537.136083] oom_kill_process+0x2b4/0x2c0
[ 1537.140097] out_of_memory+0xe4/0x594
[ 1537.143766] __alloc_pages+0xb68/0xd00
[ 1537.147521] alloc_pages+0xac/0x160
[ 1537.151013] __get_free_pages+0x14/0x40
[ 1537.154851] pgd_alloc+0x1c/0x30
[ 1537.158082] mm_init+0xf8/0x1d0
[ 1537.161228] mm_alloc+0x48/0x60
[ 1537.164368] alloc_bprm+0x7c/0x240
[ 1537.167777] do_execveat_common.isra.0+0x70/0x240
[ 1537.172486] __arm64_sys_execve+0x40/0x54
[ 1537.176502] invoke_syscall+0x48/0x114
[ 1537.180255] el0_svc_common.constprop.0+0xcc/0xec
[ 1537.184964] do_el0_svc+0x2c/0xd0
[ 1537.188280] el0_svc+0x2c/0x84
[ 1537.191340] el0t_64_sync_handler+0xf4/0x120
[ 1537.195613] el0t_64_sync+0x18c/0x190
[ 1537.199334] Mem-Info:
[ 1537.201620] active_anon:342 inactive_anon:10343 isolated_anon:0
[ 1537.201620] active_file:54 inactive_file:112 isolated_file:0
[ 1537.201620] unevictable:0 dirty:0 writeback:0
[ 1537.201620] slab_reclaimable:2620 slab_unreclaimable:7076
[ 1537.201620] mapped:1489 shmem:2473 pagetables:466
[ 1537.201620] sec_pagetables:0 bounce:0
[ 1537.201620] kernel_misc_reclaimable:0
[ 1537.201620] free:136672 free_pcp:96 free_cma:129241
[ 1537.240419] Node 0 active_anon:1368kB inactive_anon:41372kB active_file:216kB inactive_file:5052kB unevictable:0kB isolated(anon):0kB isolated(file):0kB s
[ 1537.271422] Node 0 DMA free:541636kB boost:0kB min:30000kB low:37500kB high:45000kB reserved_highatomic:0KB active_anon:1368kB inactive_anon:41372kB actiB
[ 1537.300219] lowmem_reserve[]: 0 0 0 0
[ 1537.303929] Node 0 DMA: 1015*4kB (UMEC) 743*8kB (UMEC) 417*16kB (UMEC) 235*32kB (UMEC) 116*64kB (UMEC) 25*128kB (UMEC) 4*256kB (UC) 2*512kB (UC) 0*1024kBB
[ 1537.323938] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=1048576kB
[ 1537.332708] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=32768kB
[ 1537.341292] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB
[ 1537.349776] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=64kB
[ 1537.358087] 2939 total pagecache pages
[ 1537.361876] 0 pages in swap cache
[ 1537.365229] Free swap = 0kB
[ 1537.368147] Total swap = 0kB
[ 1537.371065] 516096 pages RAM
[ 1537.373959] 0 pages HighMem/MovableOnly
[ 1537.377834] 17302 pages reserved
[ 1537.381103] 163840 pages cma reserved
[ 1537.384809] 0 pages hwpoisoned
[ 1537.387902] Tasks state (memory values in pages):
[ 1537.392652] [ pid ] uid tgid total_vm rss pgtables_bytes swapents oom_score_adj name
[ 1537.401356] [ 201] 993 201 1130 72 45056 0 0 rpcbind
[ 1537.409772] [ 202] 0 202 4529 1640 77824 0 -250 systemd-journal
[ 1537.418861] [ 222] 0 222 4691 801 69632 0 -1000 systemd-udevd
[ 1537.427787] [ 248] 994 248 20914 130 65536 0 0 systemd-timesyn
[ 1537.436884] [ 497] 0 497 620 31 49152 0 0 atd
[ 1537.444938] [ 500] 0 500 854 77 53248 0 0 crond
[ 1537.453165] [ 503] 997 503 1470 160 49152 0 -900 dbus-daemon
[ 1537.461908] [ 505] 0 505 633 24 40960 0 0 firmwared
[ 1537.470491] [ 513] 0 513 2507 180 61440 0 0 ofonod
[ 1537.478800] [ 514] 990 514 69640 137 81920 0 0 parsec
[ 1537.487120] [ 533] 0 533 599 39 40960 0 0 syslogd
[ 1537.495518] [ 534] 0 534 4546 148 65536 0 0 systemd-logind
[ 1537.504560] [ 535] 0 535 690 24 45056 0 0 tee-supplicant
[ 1537.513564] [ 540] 996 540 2769 168 61440 0 0 systemd-network
[ 1537.522680] [ 566] 0 566 3878 228 77824 0 0 connmand
[ 1537.531168] [ 645] 998 645 1538 133 57344 0 0 avahi-daemon
[ 1537.540004] [ 646] 998 646 1461 64 57344 0 0 avahi-daemon
[ 1537.548846] [ 648] 992 648 781 41 45056 0 0 rpc.statd
[ 1537.557415] [ 650] 64371 650 590 23 45056 0 0 ninfod
[ 1537.565754] [ 653] 61563 653 555 24 45056 0 0 rdisc
[ 1537.573971] [ 655] 0 655 374569 2999 290816 0 -999 containerd
[ 1537.582621] [ 658] 0 658 1311 20 49152 0 0 agetty
[ 1537.590922] [ 663] 0 663 1529 97 49152 0 0 login
[ 1537.599138] [ 666] 0 666 3430 202 69632 0 0 wpa_supplicant
[ 1537.608147] [ 667] 0 667 2344 96 61440 0 0 systemd-userdbd
[ 1537.617240] [ 677] 0 677 2964 314 65536 0 100 systemd
[ 1537.625651] [ 679] 0 679 3720 646 73728 0 100 (sd-pam)
[ 1537.634138] [ 687] 0 687 1289 403 45056 0 0 sh
[ 1537.642108] [ 789] 0 789 970 93 45056 0 0 eth_test2.sh
[ 1537.650955] [ 2355] 0 2355 2346 94 61440 0 0 systemd-userwor
[ 1537.660046] [ 2356] 0 2356 2346 94 61440 0 0 systemd-userwor
[ 1537.669137] [ 2358] 0 2358 2346 95 57344 0 0 systemd-userwor
[ 1537.678258] [ 2379] 0 2379 970 93 45056 0 0 eth_test2.sh
[ 1537.687098] oom-kill:constraint=CONSTRAINT_NONE,nodemask=(null),cpuset=/,mems_allowed=0,global_oom,task_memcg=/user.slice/user-0.slice/user@0.service,tas0
[ 1537.703009] Out of memory: Killed process 679 ((sd-pam)) total-vm:14880kB, anon-rss:2584kB, file-rss:0kB, shmem-rss:0kB, UID:0 pgtables:72kB oom_score_ad0
[ 1553.246526] page_pool_release_retry() stalled pool shutdown 310 inflight 241 sec
Fixes: 95698ff6177b ("net: fec: using page pool to manage RX buffers")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: shenwei wang <Shenwei.wang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
