| Age | Commit message (Collapse) | Author |
|---|
|
Pass the current neg_mode into phylink_mii_c22_pcs_get_state() and
phylink_mii_c22_pcs_decode_state(). Update all users of phylink PCS
that use these functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Rather than maintaining a private copy of the LPI timer, make use of
the LPI timer maintained by phylib. Note that feb->eee.tx_lpi_timer
is initialised to zero, which is just the same with phylib's copy,
so there should be no functional change.
Tested-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The fec_enet_update_cbd function calls page_pool_dev_alloc_pages but did
not handle the case when it returned NULL. There was a WARN_ON(!new_page)
but it would still proceed to use the NULL pointer and then crash.
This case does seem somewhat rare but when the system is under memory
pressure it can happen. One case where I can duplicate this with some
frequency is when writing over a smbd share to a SATA HDD attached to an
imx6q.
Setting /proc/sys/vm/min_free_kbytes to higher values also seems to solve
the problem for my test case. But it still seems wrong that the fec driver
ignores the memory allocation error and can crash.
This commit handles the allocation error by dropping the current packet.
Fixes: 95698ff6177b5 ("net: fec: using page pool to manage RX buffers")
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250113154846.1765414-1-kgroeneveld@lenbrook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both ENETC PF and VF drivers share enetc_setup_tc_mqprio() to configure
MQPRIO. And enetc_setup_tc_mqprio() calls enetc_change_preemptible_tcs()
to configure preemptible TCs. However, only PF is able to configure
preemptible TCs. Because only PF has related registers, while VF does not
have these registers. So for VF, its hw->port pointer is NULL. Therefore,
VF will access an invalid pointer when accessing a non-existent register,
which will cause a crash issue. The simplified log is as follows.
root@ls1028ardb:~# tc qdisc add dev eno0vf0 parent root handle 100: \
mqprio num_tc 4 map 0 0 1 1 2 2 3 3 queues 1@0 1@1 1@2 1@3 hw 1
[ 187.290775] Unable to handle kernel paging request at virtual address 0000000000001f00
[ 187.424831] pc : enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.430518] lr : enetc_mm_commit_preemptible_tcs+0x30c/0x400
[ 187.511140] Call trace:
[ 187.513588] enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.518918] enetc_setup_tc_mqprio+0x180/0x214
[ 187.523374] enetc_vf_setup_tc+0x1c/0x30
[ 187.527306] mqprio_enable_offload+0x144/0x178
[ 187.531766] mqprio_init+0x3ec/0x668
[ 187.535351] qdisc_create+0x15c/0x488
[ 187.539023] tc_modify_qdisc+0x398/0x73c
[ 187.542958] rtnetlink_rcv_msg+0x128/0x378
[ 187.547064] netlink_rcv_skb+0x60/0x130
[ 187.550910] rtnetlink_rcv+0x18/0x24
[ 187.554492] netlink_unicast+0x300/0x36c
[ 187.558425] netlink_sendmsg+0x1a8/0x420
[ 187.606759] ---[ end trace 0000000000000000 ]---
In addition, some PFs also do not support configuring preemptible TCs,
such as eno1 and eno3 on LS1028A. It won't crash like it does for VFs,
but we should prevent these PFs from accessing these unimplemented
registers.
Fixes: 827145392a4a ("net: enetc: only commit preemptible TCs to hardware when MM TX is active")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configuring TSN (Qbv, Qbu, PSFP) capabilities requires access to port
registers, which are available to the PSI but not the VSI.
Yet, the SI port capability register 0 (PSICAPR0), exposed to both PSIs
and VSIs, presents the same capabilities to the VF as to the PF, thus
leading the VF driver into thinking it can configure these features.
In the case of ENETC_SI_F_QBU, having it set in the VF leads to a crash:
root@ls1028ardb:~# tc qdisc add dev eno0vf0 parent root handle 100: \
mqprio num_tc 4 map 0 0 1 1 2 2 3 3 queues 1@0 1@1 1@2 1@3 hw 1
[ 187.290775] Unable to handle kernel paging request at virtual address 0000000000001f00
[ 187.424831] pc : enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.430518] lr : enetc_mm_commit_preemptible_tcs+0x30c/0x400
[ 187.511140] Call trace:
[ 187.513588] enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.518918] enetc_setup_tc_mqprio+0x180/0x214
[ 187.523374] enetc_vf_setup_tc+0x1c/0x30
[ 187.527306] mqprio_enable_offload+0x144/0x178
[ 187.531766] mqprio_init+0x3ec/0x668
[ 187.535351] qdisc_create+0x15c/0x488
[ 187.539023] tc_modify_qdisc+0x398/0x73c
[ 187.542958] rtnetlink_rcv_msg+0x128/0x378
[ 187.547064] netlink_rcv_skb+0x60/0x130
[ 187.550910] rtnetlink_rcv+0x18/0x24
[ 187.554492] netlink_unicast+0x300/0x36c
[ 187.558425] netlink_sendmsg+0x1a8/0x420
[ 187.606759] ---[ end trace 0000000000000000 ]---
while the other TSN features in the VF are harmless, because the
net_device_ops used for the VF driver do not expose entry points for
these other features.
These capability bits are in the process of being defeatured from the SI
registers. We should read them from the port capability register, where
they are also present, and which is naturally only exposed to the PF.
The change to blame (relevant for stable backports) is the one where
this started being a problem, aka when the kernel started to crash due
to the wrong capability seen by the VF driver.
Fixes: 827145392a4a ("net: enetc: only commit preemptible TCs to hardware when MM TX is active")
Reported-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently added this error path. We need to call enetc_pci_remove()
before returning. It cleans up the resources from enetc_pci_probe().
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/93888efa-c838-4682-a7e5-e6bf318e844e@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc7).
Conflicts:
drivers/net/ethernet/freescale/enetc/enetc_pf.c
e15c5506dd39 ("net: enetc: allocate vf_state during PF probes")
3774409fd4c6 ("net: enetc: build enetc_pf_common.c as a separate module")
https://lore.kernel.org/20241105114100.118bd35e@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/ti/am65-cpsw-nuss.c
de794169cf17 ("net: ethernet: ti: am65-cpsw: Fix multi queue Rx on J7")
4a7b2ba94a59 ("net: ethernet: ti: am65-cpsw: Use tstats instead of open coded version")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When nvmem is not ready, of_get_ethdev_address returns -EPROBE_DEFER. In
such a case, return -EPROBE_DEFER to avoid not having a proper MAC
address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241104210127.307420-5-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoids having to unregister manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241104210127.307420-4-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoids manual frees. Removes one goto.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241104210127.307420-3-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoids manual frees for it. Funny enough the free in _remove should be
the last thing done.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241104210127.307420-2-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20241105093125.1087202-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sparse provides the following output:
warning: cast to restricted __be32
This is a harmless warning due to the fact that we dereference the hash
stored in the FD using an incorrect type annotation. Suppress the
warning by using the correct __be32 type instead of u32. No functional
change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://patch.msgid.link/20241029164317.50182-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Multi-buffer frame descriptors (FDs) point to a buffer holding a
scatter/gather table (SGT), which is a finite array of fixed-size
entries, the last of which has qm_sg_entry_is_final(&sgt[i]) == true.
Each SGT entry points to a buffer holding pieces of the frame.
DPAARM.pdf explains in the figure called "Internal and External Margins,
Scatter/Gather Frame Format" that the SGT table is located within its
buffer at the same offset as the frame data start is located within the
first packet buffer.
+------------------------+
Scatter/Gather Buffer | First Buffer | Last Buffer
^ +------------+ ^ +-|---->^ +------------+ +->+------------+
| | | | ICEOF | | | | | |////////////|
| +------------+ v | | | | | |////////////|
BSM | |/ part of //| | |BSM | | | |////////////|
| |/ Internal /| | | | | | |////////////|
| |/ Context //| | | | | | |// Frame ///|
| +------------+ | | | | | ... |/ content //|
| | | | | | | | |////////////|
| | | | | | | | |////////////|
v +------------+ | | v +------------+ |////////////|
| Scatter/ //| sgt[0]--+ | |// Frame ///| |////////////|
| Gather List| ... | |/ content //| +------------+ ^
|////////////| sgt[N]----+ |////////////| | | | BEM
|////////////| |////////////| | | |
+------------+ +------------+ +------------+ v
BSM = Buffer Start Margin, BEM = Buffer End Margin, both are configured
by dpaa_eth_init_rx_port() for the RX FMan port relevant here.
sg_fd_to_skb() runs in the calling context of rx_default_dqrr() -
the NAPI receive callback - which only expects to receive contiguous
(qm_fd_contig) or scatter/gather (qm_fd_sg) frame descriptors.
Everything else is irrelevant codewise.
The processing done by sg_fd_to_skb() is weird because it does not
conform to the expectations laid out by the aforementioned figure.
Namely, it parses the OFFSET field only for SGT entries with i != 0
(codewise, skb != NULL). In those cases, OFFSET should always be 0.
Also, it does not parse the OFFSET field for the sgt[0] case, the only
case where the buffer offset is meaningful in this context. There, it
uses the fd_off, aka the offset to the Scatter/Gather List in the
Scatter/Gather Buffer from the figure. By equivalence, they should both
be equal to the BSM (in turn, equal to priv->rx_headroom).
This can actually be explained due to the bug which we had in
qm_sg_entry_get_off() until the previous change:
- qm_sg_entry_get_off() did not actually _work_ for sgt[0]. It returned
zero even with a non-zero offset, so fd_off had to be used as a fill-in.
- qm_sg_entry_get_off() always returned zero for sgt[i>0], and that
resulted in no user-visible bug, because the buffer offset _was
supposed_ to be zero for those buffers. So remove it from calculations.
Add assertions about the OFFSET field in both cases (first or subsequent
SGT entries) to make it absolutely obvious when something is not well
handled.
Similar logic can be seen in the driver for the architecturally similar
DPAA2, where dpaa2_eth_build_frag_skb() calls dpaa2_sg_get_offset() only
for i == 0. For the rest, there is even a comment stating the same thing:
* Data in subsequent SG entries is stored from the
* beginning of the buffer, so we don't need to add the
* sg_offset.
Tested on LS1046A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://patch.msgid.link/20241029164317.50182-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The i.MX95 ENETC has been upgraded to revision 4.1, which is different
from the LS1028A ENETC (revision 1.0) except for the SI part. Therefore,
the fsl-enetc driver is incompatible with i.MX95 ENETC PF. So add new
nxp-enetc4 driver to support i.MX95 ENETC PF, and this driver will be
used to support the ENETC PF with major revision 4 for other SoCs in the
future.
Currently, the nxp-enetc4 driver only supports basic transmission feature
for i.MX95 ENETC PF, the more basic and advanced features will be added
in the subsequent patches. In addition, PCS support has not been added
yet, so 10G ENETC (ENETC instance 2) is not supported now.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a situation where num_tx_rings cannot be divided by bdr_int_num.
For example, num_tx_rings is 8 and bdr_int_num is 3. According to the
previous logic, this results in two tx_bdr corresponding memories not
being allocated, so when sending packets to tx ring 6 or 7, wild pointers
will be accessed. Of course, this issue doesn't exist on LS1028A, because
its num_tx_rings is 8, and bdr_int_num is either 1 or 2. However, there
is a risk for the upcoming i.MX95. Therefore, it is necessary to ensure
that each tx_bdr can be allocated to the corresponding memory.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract enetc_int_vector_init() and enetc_int_vector_destroy() from
enetc_alloc_msix() so that the code is more concise and readable.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The verdor ID and device ID of i.MX95 EMDIO are different from LS1028A
EMDIO, so add new vendor ID and device ID to pci_device_id table to
support i.MX95 EMDIO.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ERR050089 workaround causes performance degradation and potential
functional issues (e.g., RCU stalls) under certain workloads. Since
new SoCs like i.MX95 do not require this workaround, use a static key
to compile out enetc_lock_mdio() and enetc_unlock_mdio() at runtime,
improving performance and avoiding unnecessary logic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compile enetc_pf_common.c as a standalone module to allow shared usage
between ENETC v1 and v4 PF drivers. Add struct enetc_pf_ops to register
different hardware operation interfaces for both ENETC v1 and v4 PF
drivers.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ENETC PF driver of LS1028A (rev 1.0) is incompatible with the version
used on the i.MX95 platform (rev 4.1), except for the station interface
(SI) part. To reduce code redundancy and prepare for a new driver for rev
4.1 and later, extract shared interfaces from enetc_pf.c and move them to
enetc_pf_common.c. This refactoring lays the groundwork for compiling
enetc_pf_common.c into a shared driver for both platforms' PF drivers.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netc-blk-ctrl driver is used to configure Integrated Endpoint
Register Block (IERB) and Privileged Register Block (PRB) of NETC.
For i.MX platforms, it is also used to configure the NETCMIX block.
The IERB contains registers that are used for pre-boot initialization,
debug, and non-customer configuration. The PRB controls global reset
and global error handling for NETC. The NETCMIX block is mainly used
to set MII protocol and PCS protocol of the links, it also contains
settings for some other functions.
Note the IERB configuration registers can only be written after being
unlocked by PRB, otherwise, all write operations are inhibited. A warm
reset is performed when the IERB is unlocked, and it results in an FLR
to all NETC devices. Therefore, all NETC device drivers must be probed
or initialized after the warm reset is finished.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the previous implementation, vf_state is allocated memory only when VF
is enabled. However, net_device_ops::ndo_set_vf_mac() may be called before
VF is enabled to configure the MAC address of VF. If this is the case,
enetc_pf_set_vf_mac() will access vf_state, resulting in access to a null
pointer. The simplified error log is as follows.
root@ls1028ardb:~# ip link set eno0 vf 1 mac 00:0c:e7:66:77:89
[ 173.543315] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
[ 173.637254] pc : enetc_pf_set_vf_mac+0x3c/0x80 Message from sy
[ 173.641973] lr : do_setlink+0x4a8/0xec8
[ 173.732292] Call trace:
[ 173.734740] enetc_pf_set_vf_mac+0x3c/0x80
[ 173.738847] __rtnl_newlink+0x530/0x89c
[ 173.742692] rtnl_newlink+0x50/0x7c
[ 173.746189] rtnetlink_rcv_msg+0x128/0x390
[ 173.750298] netlink_rcv_skb+0x60/0x130
[ 173.754145] rtnetlink_rcv+0x18/0x24
[ 173.757731] netlink_unicast+0x318/0x380
[ 173.761665] netlink_sendmsg+0x17c/0x3c8
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241031060247.1290941-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net_dim() is currently passed a struct dim_sample argument by value.
struct dim_sample is 24 bytes. Since this is greater 16 bytes, x86-64
passes it on the stack. All callers have already initialized dim_sample
on the stack, so passing it by value requires pushing a duplicated copy
to the stack. Either witing to the stack and immediately reading it, or
perhaps dereferencing addresses relative to the stack pointer in a chain
of push instructions, seems to perform quite poorly.
In a heavy TCP workload, mlx5e_handle_rx_dim() consumes 3% of CPU time,
94% of which is attributed to the first push instruction to copy
dim_sample on the stack for the call to net_dim():
// Call ktime_get()
0.26 |4ead2: call 4ead7 <mlx5e_handle_rx_dim+0x47>
// Pass the address of struct dim in %rdi
|4ead7: lea 0x3d0(%rbx),%rdi
// Set dim_sample.pkt_ctr
|4eade: mov %r13d,0x8(%rsp)
// Set dim_sample.byte_ctr
|4eae3: mov %r12d,0xc(%rsp)
// Set dim_sample.event_ctr
0.15 |4eae8: mov %bp,0x10(%rsp)
// Duplicate dim_sample on the stack
94.16 |4eaed: push 0x10(%rsp)
2.79 |4eaf1: push 0x10(%rsp)
0.07 |4eaf5: push %rax
// Call net_dim()
0.21 |4eaf6: call 4eafb <mlx5e_handle_rx_dim+0x6b>
To allow the caller to reuse the struct dim_sample already on the stack,
pass the struct dim_sample by reference to net_dim().
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Arthur Kiyanovski <akiyano@amazon.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Link: https://patch.msgid.link/20241031002326.3426181-2-csander@purestorage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sparse warns:
note: in included file (through ../include/trace/trace_events.h,
../include/trace/define_trace.h,
../drivers/net/ethernet/freescale/dpaa/dpaa_eth_trace.h):
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] fd_status
got restricted __be32 const [usertype] status
We take struct qm_fd :: status, store it and print it as an u32,
though it is a big endian field. We should print the FD status in
CPU endianness for ease of debug and consistency between PowerPC and
Arm systems.
Though it is a not often used debug feature, it is best to treat it as
a bug and backport the format change to all supported stable kernels,
for consistency.
Fixes: eb11ddf36eb8 ("dpaa_eth: add trace points")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://patch.msgid.link/20241029163105.44135-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MAC address of VF can be configured through the mailbox mechanism of
ENETC, but the previous implementation forgot to set the MAC address in
net_device, resulting in the SMAC of the sent frames still being the old
MAC address. Since the MAC address in the hardware has been changed, Rx
cannot receive frames with the DMAC address as the new MAC address. The
most obvious phenomenon is that after changing the MAC address, we can
see that the MAC address of eno0vf0 has not changed through the "ifconfig
eno0vf0" command and the IP address cannot be obtained .
root@ls1028ardb:~# ifconfig eno0vf0 down
root@ls1028ardb:~# ifconfig eno0vf0 hw ether 00:04:9f:3a:4d:56 up
root@ls1028ardb:~# ifconfig eno0vf0
eno0vf0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
ether 66:36:2c:3b:87:76 txqueuelen 1000 (Ethernet)
RX packets 794 bytes 69239 (69.2 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 11 bytes 2226 (2.2 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Fixes: beb74ac878c8 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20241029090406.841836-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cell-index value is obtained from Device Tree and then used to calculate
the index for accessing arrays port_mfl[], mac_mfl[] and intr_mng[].
In case of broken DT due to any error cell-index can contain any value
and it is possible to go beyond the array boundaries which can lead
at least to memory corruption.
Validate cell-index value obtained from Device Tree.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://patch.msgid.link/20241028065824.15452-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the pointer. Cleans up the code quite well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Lee Trager <lee@trager.us>
Link: https://patch.msgid.link/20241025203757.288367-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In mac_probe() there are multiple calls to of_find_device_by_node(),
fman_bind() and fman_port_bind() which takes references to of_dev->dev.
Not all references taken by these calls are released later on error path
in mac_probe() and in mac_remove() which lead to reference leaks.
Add references release.
Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In mac_probe() there are calls to of_find_device_by_node() which takes
references to of_dev->dev. These references are not saved and not released
later on error path in mac_probe() and in mac_remove().
Add new fields into mac_device structure to save references taken for
future use in mac_probe() and mac_remove().
This is a preparation for further reference leaks fix.
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c1e ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c41c ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The correct format string for resource_size_t is %pa which
acts on the address of the variable to be formatted [1].
[1] https://elixir.bootlin.com/linux/v6.11.3/source/Documentation/core-api/printk-formats.rst#L229
Introduced by commit 9d9326d3bc0e ("phy: Change mii_bus id field to a string")
Flagged by gcc-14 as:
drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c: In function 'fs_mii_bitbang_init':
drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c:126:46: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
126 | snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
No functional change intended.
Compile tested only.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/711d7f6d-b785-7560-f4dc-c6aad2cce99@linux-m68k.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241014-net-pa-fmt-v1-2-dcc9afb8858b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The correct format string for resource_size_t is %pa which
acts on the address of the variable to be formatted [1].
[1] https://elixir.bootlin.com/linux/v6.11.3/source/Documentation/core-api/printk-formats.rst#L229
Introduced by commit 9d9326d3bc0e ("phy: Change mii_bus id field to a string")
Flagged by gcc-14 as:
drivers/net/ethernet/freescale/fec_mpc52xx_phy.c: In function 'mpc52xx_fec_mdio_probe':
drivers/net/ethernet/freescale/fec_mpc52xx_phy.c:97:46: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
97 | snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
No functional change intended.
Compile tested only.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/711d7f6d-b785-7560-f4dc-c6aad2cce99@linux-m68k.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241014-net-pa-fmt-v1-1-dcc9afb8858b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Timestamp values are read using pointers to 64-bit big endian values.
But the type of these pointers is u64 *, host byte order.
Use __be64 * instead.
Flagged by Sparse:
.../gianfar.c:2212:60: warning: cast to restricted __be64
.../gianfar.c:2475:53: warning: cast to restricted __be64
Introduced by
commit cc772ab7cdca ("gianfar: Add hardware RX timestamping support").
Compile tested only.
No functional change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20241011-gianfar-be64-v1-1-a77ebe972176@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When running "xdp-bench tx eno0" to test the XDP_TX feature of ENETC
on LS1028A, it was found that if the command was re-run multiple times,
Rx could not receive the frames, and the result of xdp-bench showed
that the rx rate was 0.
root@ls1028ardb:~# ./xdp-bench tx eno0
Hairpinning (XDP_TX) packets on eno0 (ifindex 3; driver fsl_enetc)
Summary 2046 rx/s 0 err,drop/s
Summary 0 rx/s 0 err,drop/s
Summary 0 rx/s 0 err,drop/s
Summary 0 rx/s 0 err,drop/s
By observing the Rx PIR and CIR registers, CIR is always 0x7FF and
PIR is always 0x7FE, which means that the Rx ring is full and can no
longer accommodate other Rx frames. Therefore, the problem is caused
by the Rx BD ring not being cleaned up.
Further analysis of the code revealed that the Rx BD ring will only
be cleaned if the "cleaned_cnt > xdp_tx_in_flight" condition is met.
Therefore, some debug logs were added to the driver and the current
values of cleaned_cnt and xdp_tx_in_flight were printed when the Rx
BD ring was full. The logs are as follows.
[ 178.762419] [XDP TX] >> cleaned_cnt:1728, xdp_tx_in_flight:2140
[ 178.771387] [XDP TX] >> cleaned_cnt:1941, xdp_tx_in_flight:2110
[ 178.776058] [XDP TX] >> cleaned_cnt:1792, xdp_tx_in_flight:2110
From the results, the max value of xdp_tx_in_flight has reached 2140.
However, the size of the Rx BD ring is only 2048. So xdp_tx_in_flight
did not drop to 0 after enetc_stop() is called and the driver does not
clear it. The root cause is that NAPI is disabled too aggressively,
without having waited for the pending XDP_TX frames to be transmitted,
and their buffers recycled, so that xdp_tx_in_flight cannot naturally
drop to 0. Later, enetc_free_tx_ring() does free those stale, unsent
XDP_TX packets, but it is not coded up to also reset xdp_tx_in_flight,
hence the manifestation of the bug.
One option would be to cover this extra condition in enetc_free_tx_ring(),
but now that the ENETC_TX_DOWN exists, we have created a window at
the beginning of enetc_stop() where NAPI can still be scheduled, but
any concurrent enqueue will be blocked. Therefore, enetc_wait_bdrs()
and enetc_disable_tx_bdrs() can be called with NAPI still scheduled,
and it is guaranteed that this will not wait indefinitely, but instead
give us an indication that the pending TX frames have orderly dropped
to zero. Only then should we call napi_disable().
This way, enetc_free_tx_ring() becomes entirely redundant and can be
dropped as part of subsequent cleanup.
The change also refactors enetc_start() so that it looks like the
mirror opposite procedure of enetc_stop().
Fixes: ff58fda09096 ("net: enetc: prioritize ability to go down over packet processing")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241010092056.298128-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Tx BD rings are disabled first in enetc_stop() and the driver
waits for them to become empty. This operation is not safe while
the ring is actively transmitting frames, and will cause the ring
to not be empty and hardware exception. As described in the NETC
block guide, software should only disable an active Tx ring after
all pending ring entries have been consumed (i.e. when PI = CI).
Disabling a transmit ring that is actively processing BDs risks
a HW-SW race hazard whereby a hardware resource becomes assigned
to work on one or more ring entries only to have those entries be
removed due to the ring becoming disabled.
When testing XDP_REDIRECT feautre, although all frames were blocked
from being put into Tx rings during ring reconfiguration, the similar
warning log was still encountered:
fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #6 clear
fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #7 clear
The reason is that when there are still unsent frames in the Tx ring,
disabling the Tx ring causes the remaining frames to be unable to be
sent out. And the Tx ring cannot be restored, which means that even
if the xdp program is uninstalled, the Tx frames cannot be sent out
anymore. Therefore, correct the operation order in enect_start() and
enect_stop().
Fixes: ff58fda09096 ("net: enetc: prioritize ability to go down over packet processing")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241010092056.298128-4-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When testing the XDP_REDIRECT function on the LS1028A platform, we
found a very reproducible issue that the Tx frames can no longer be
sent out even if XDP_REDIRECT is turned off. Specifically, if there
is a lot of traffic on Rx direction, when XDP_REDIRECT is turned on,
the console may display some warnings like "timeout for tx ring #6
clear", and all redirected frames will be dropped, the detailed log
is as follows.
root@ls1028ardb:~# ./xdp-bench redirect eno0 eno2
Redirecting from eno0 (ifindex 3; driver fsl_enetc) to eno2 (ifindex 4; driver fsl_enetc)
[203.849809] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #5 clear
[204.006051] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #6 clear
[204.161944] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #7 clear
eno0->eno2 1420505 rx/s 1420590 err,drop/s 0 xmit/s
xmit eno0->eno2 0 xmit/s 1420590 drop/s 0 drv_err/s 15.71 bulk-avg
eno0->eno2 1420484 rx/s 1420485 err,drop/s 0 xmit/s
xmit eno0->eno2 0 xmit/s 1420485 drop/s 0 drv_err/s 15.71 bulk-avg
By analyzing the XDP_REDIRECT implementation of enetc driver, the
driver will reconfigure Tx and Rx BD rings when a bpf program is
installed or uninstalled, but there is no mechanisms to block the
redirected frames when enetc driver reconfigures rings. Similarly,
XDP_TX verdicts on received frames can also lead to frames being
enqueued in the Tx rings. Because XDP ignores the state set by the
netif_tx_wake_queue() API, so introduce the ENETC_TX_DOWN flag to
suppress transmission of XDP frames.
Fixes: c33bfaf91c4c ("net: enetc: set up XDP program under enetc_reconfigure()")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241010092056.298128-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The xdp_drops statistic indicates the number of XDP frames dropped in
the Rx direction. However, enetc_xdp_drop() is also used in XDP_TX and
XDP_REDIRECT actions. If frame loss occurs in these two actions, the
frames loss count should not be included in xdp_drops, because there
are already xdp_tx_drops and xdp_redirect_failures to count the frame
loss of these two actions, so it's better to remove xdp_drops statistic
from enetc_xdp_drop() and increase xdp_drops in XDP_DROP action.
Fixes: 7ed2bc80074e ("net: enetc: add support for XDP_TX")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241010092056.298128-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc3).
No conflicts and no adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some platforms (such as i.MX25 and i.MX27) do not support PTP, so on
these platforms fec_ptp_init() is not called and the related members
in fep are not initialized. However, fec_ptp_save_state() is called
unconditionally, which causes the kernel to panic. Therefore, add a
condition so that fec_ptp_save_state() is not called if PTP is not
supported.
Fixes: a1477dc87dc4 ("net: fec: Restart PPS after link state change")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/lkml/353e41fe-6bb4-4ee9-9980-2da2a9c1c508@roeck-us.net/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20241008061153.1977930-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The original driver first unregisters then re-registers all multicast
addresses in the struct net_device_ops::ndo_set_rx_mode() callback.
As the networking stack calls ndo_set_rx_mode() if a single multicast
address change occurs, a significant amount of time may be used to first
unregister and then re-register unchanged multicast addresses. This
leads to performance issues when tracking large numbers of multicast
addresses.
Replace the unregister and register loop and the hand crafted
mc_addr_list list handling with __dev_mc_sync(), to only update entries
which have changed.
On profiling with an fsl_dpa NIC, this patch presented a speedup of
around 40 when successively setting up 2000 multicast groups using
setsockopt(), without drawbacks on smaller numbers of multicast groups.
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a typo in comments: bellow -> below.
Reported-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Kreimer <algonell@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241006130829.13967-1-algonell@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Depending on the SoC where the FEC is integrated into the PPS channel
might be routed to different timer instances. Make this configurable
from the devicetree.
When the related DT property is not present fallback to the previous
default and use channel 0.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Csókás, Bence <csokas.bence@prolan.hu>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Preparation patch to allow for PPS channel configuration, no functional
change intended.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Csókás, Bence <csokas.bence@prolan.hu>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/ethernet to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/18f7c585a1a8a8ac8b03a2fca7de19bd5c52ac2b.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ieee802154, bluetooth and netfilter.
Current release - regressions:
- eth: mlx5: fix wrong reserved field in hca_cap_2 in mlx5_ifc
- eth: am65-cpsw: fix forever loop in cleanup code
Current release - new code bugs:
- eth: mlx5: HWS, fixed double-free in error flow of creating SQ
Previous releases - regressions:
- core: avoid potential underflow in qdisc_pkt_len_init() with UFO
- core: test for not too small csum_start in virtio_net_hdr_to_skb()
- vrf: revert "vrf: remove unnecessary RCU-bh critical section"
- bluetooth:
- fix uaf in l2cap_connect
- fix possible crash on mgmt_index_removed
- dsa: improve shutdown sequence
- eth: mlx5e: SHAMPO, fix overflow of hd_per_wq
- eth: ip_gre: fix drops of small packets in ipgre_xmit
Previous releases - always broken:
- core: fix gso_features_check to check for both
dev->gso_{ipv4_,}max_size
- core: fix tcp fraglist segmentation after pull from frag_list
- netfilter: nf_tables: prevent nf_skb_duplicated corruption
- sctp: set sk_state back to CLOSED if autobind fails in
sctp_listen_start
- mac802154: fix potential RCU dereference issue in
mac802154_scan_worker
- eth: fec: restart PPS after link state change"
* tag 'net-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
dt-bindings: net: xlnx,axi-ethernet: Add missing reg minItems
doc: net: napi: Update documentation for napi_schedule_irqoff
net/ncsi: Disable the ncsi work before freeing the associated structure
net: phy: qt2025: Fix warning: unused import DeviceId
gso: fix udp gso fraglist segmentation after pull from frag_list
bridge: mcast: Fail MDB get request on empty entry
vrf: revert "vrf: Remove unnecessary RCU-bh critical section"
net: ethernet: ti: am65-cpsw: Fix forever loop in cleanup code
net: phy: realtek: Check the index value in led_hw_control_get
ppp: do not assume bh is held in ppp_channel_bridge_input()
selftests: rds: move include.sh to TEST_FILES
net: test for not too small csum_start in virtio_net_hdr_to_skb()
net: gso: fix tcp fraglist segmentation after pull from frag_list
ipv4: ip_gre: Fix drops of small packets in ipgre_xmit
net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check
net: add more sanity checks to qdisc_pkt_len_init()
net: avoid potential underflow in qdisc_pkt_len_init() with UFO
net: ethernet: ti: cpsw_ale: Fix warning on some platforms
net: microchip: Make FDMA config symbol invisible
...
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
On link-state change, the controller gets reset,
which clears all PTP registers, including PHC time,
calibrated clock correction values etc. For correct
IEEE 1588 operation we need to restore these after
the reset.
Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20240924093705.2897329-2-csokas.bence@prolan.hu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
