| Age | Commit message (Collapse) | Author |
|---|
|
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
This can be observed by the following log:
fec 5b040000.ethernet eth0: MDIO read timeout
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8f0 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
Fixes: 557d5dc83f68 ("net: fec: use mac-managed PHY PM")
Closes: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
[jernberg: commit message]
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240328155909.59613-2-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enabling/disabling of EEE in the MAC should happen as a result of
auto negotiation. So move the enable/disable into
fec_enet_adjust_link() which gets called by phylib when there is a
change in link status.
fec_enet_set_eee() now just stores away the LPI timer value.
Everything else is passed to phylib, so it can correctly setup the
PHY.
fec_enet_get_eee() relies on phylib doing most of the work,
the MAC driver just adds the LPI timer value.
Call phy_support_eee() if the quirk is present to indicate the MAC
actually supports EEE.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> (On iMX8MP debix)
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240302195306.3207716-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FEC is about to get its EEE code re-written. To allow this, move
fec_enet_eee_mode_set() before fec_enet_adjust_link() which will
need to call it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240302195306.3207716-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/mptcp/protocol.c
adf1bb78dab5 ("mptcp: fix snd_wnd initialization for passive socket")
9426ce476a70 ("mptcp: annotate lockless access for RX path fields")
https://lore.kernel.org/all/20240228103048.19255709@canb.auug.org.au/
Adjacent changes:
drivers/dpll/dpll_core.c
0d60d8df6f49 ("dpll: rely on rcu for netdev_dpll_pin()")
e7f8df0e81bf ("dpll: move xa_erase() call in to match dpll_pin_alloc() error path order")
drivers/net/veth.c
1ce7d306ea63 ("veth: try harder when allocating queue memory")
0bef512012b1 ("net: add netdev_lockdep_set_classes() to virtual drivers")
drivers/net/wireless/intel/iwlwifi/mvm/d3.c
8c9bef26e98b ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
78f65fbf421a ("wifi: iwlwifi: mvm: ensure offloading TID queue exists")
net/wireless/nl80211.c
f78c1375339a ("wifi: nl80211: reject iftype change with mesh ID change")
414532d8aa89 ("wifi: cfg80211: use IEEE80211_MAX_MESH_ID_LEN appropriately")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tree
Since commit 5d93cfcf7360 ("net: dpaa: Convert to phylink"), we support
the "10gbase-r" phy-mode through a driver-based conversion of "xgmii",
but we still don't actually support it when the device tree specifies
"10gbase-r" proper.
This is because boards such as LS1046A-RDB do not define pcs-handle-names
(for whatever reason) in the ethernet@f0000 device tree node, and the
code enters through this code path:
err = of_property_match_string(mac_node, "pcs-handle-names", "xfi");
// code takes neither branch and falls through
if (err >= 0) {
(...)
} else if (err != -EINVAL && err != -ENODATA) {
goto _return_fm_mac_free;
}
(...)
/* For compatibility, if pcs-handle-names is missing, we assume this
* phy is the first one in pcsphy-handle
*/
err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii");
if (err == -EINVAL || err == -ENODATA)
pcs = memac_pcs_create(mac_node, 0); // code takes this branch
else if (err < 0)
goto _return_fm_mac_free;
else
pcs = memac_pcs_create(mac_node, err);
// A default PCS is created and saved in "pcs"
// This determination fails and mistakenly saves the default PCS
// memac->sgmii_pcs instead of memac->xfi_pcs, because at this
// stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER.
if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII)
memac->xfi_pcs = pcs;
else
memac->sgmii_pcs = pcs;
In other words, in the absence of pcs-handle-names, the default
xfi_pcs assignment logic only works when in the device tree we have
PHY_INTERFACE_MODE_XGMII.
By reversing the order between the fallback xfi_pcs assignment and the
"xgmii" overwrite with "10gbase-r", we are able to support both values
in the device tree, with identical behavior.
Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree
conversion, because it would break forward compatibility (new device
tree with old kernel). The only way to modify existing device trees to
phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this
value and handle it properly.
One reason why the conversion is desirable is because with pre-phylink
kernels, the Aquantia PHY driver used to warn about the improper use
of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest)
device tree that works with all supported stable kernel versions.
Note that the blamed commit does not constitute a regression per se.
Older stable kernels like 6.1 still do not work with "10gbase-r", but
for a different reason. That is a battle for another time.
[1] https://lore.kernel.org/netdev/20240214-ls1046-dts-use-10gbase-r-v1-1-8c2d68547393@concurrent-rt.com/
Fixes: 5d93cfcf7360 ("net: dpaa: Convert to phylink")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FEC_ENET_FCE is the Flow Control Enable bit (bit 5) of the RCR.
This is now defined as FEC_RCR_FLOWCTL.
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240212153717.10023-2-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add defines for bits of ECR, RCR control registers, TX watermark etc.
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240212153717.10023-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fec_enet_get_eee() sets edata->eee_active and edata->eee_enabled from
its own copy, and then calls phy_ethtool_get_eee() which in turn will
call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Therefore, setting these members in fec_enet_get_eee() is redundant.
Remove this, and remove the setting of fep->eee.eee_active member which
becomes a write-only variable.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1rWbN2-002cCh-MY@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When repeatedly changing the interface link speed using the command below:
ethtool -s eth0 speed 100 duplex full
ethtool -s eth0 speed 1000 duplex full
The following errors may sometimes be reported by the ARM SMMU driver:
[ 5395.035364] fec 5b040000.ethernet eth0: Link is Down
[ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault:
fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2
[ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
It is identified that the FEC driver does not properly stop the TX queue
during the link speed transitions, and this results in the invalid virtual
I/O address translations from the SMMU and causes the context faults.
Fixes: dbc64a8ea231 ("net: fec: move calls to quiesce/resume packet processing out of fec_restart()")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20240123165141.2008104-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Freescale PQ MDIO driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-9-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the FEC (MPC8xx) Ethernet controller.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240123190332.677489-8-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the NXP ENETC Ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-7-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver code proper is handled by the lynx_pcs. The enetc just needs
to populate phylink's supported_interfaces array, and return true for
this phy-mode in enetc_port_has_pcs(), such that it creates an internal
MDIO bus through which the Lynx PCS registers are accessed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20240103113445.3892971-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case a DPAA2 switch interface joins a bridge, the FDB used on the
port will be changed to the one associated with the bridge. What this
means exactly is that any VLAN installed on the port will need to be
removed and then installed back so that it points to the new FDB.
Once this is done, the previous FDB will become unused (no VLAN to
point to it). Even though no traffic will reach this FDB, it's best to
just cleanup the state of the FDB by zeroing its egress flood domain.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two different DPAA2 switch ports from two different DPSW instances
cannot be under the same bridge. Instead of checking for this
unsupported configuration in the CHANGEUPPER event, check it as early as
possible in the PRECHANGEUPPER one.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create separate functions, dpaa2_switch_port_prechangeupper and
dpaa2_switch_port_changeupper, to be called directly when a DPSW port
changes its upper device.
This way we are not open-coding everything in the main event callback
and we can easily extent, for example, with bond offload.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DPSW object has multiple event sources multiplexed over the same
IRQ. The driver has the capability to configure only some of these
events to trigger the IRQ.
The dpsw_get_irq_status() can clear events automatically based on the
value stored in the 'status' variable passed to it. We don't want that
to happen because we could get into a situation when we are clearing
more events than we actually handled.
Just resort to manually clearing the events that we handled. Also, since
status is not used on the out path we remove its initialization to zero.
This change does not have a user-visible effect because the dpaa2-switch
driver enables and handles all the DPSW events which exist at the
moment.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 84cba72956fd ("dpaa2-switch: integrate the MAC endpoint support")
added support for MAC endpoints in the dpaa2-switch driver but omitted
to add the ENDPOINT_CHANGED irq to the list of interrupt sources. Fix
this by extending the list of events which can raise an interrupt by
extending the mask passed to the dpsw_set_irq_mask() firmware API.
There is no user visible impact even without this patch since whenever a
switch interface is connected/disconnected from an endpoint both events
are set (LINK_CHANGED and ENDPOINT_CHANGED) and, luckily, the
LINK_CHANGED event could actually raise the interrupt and thus get the
MAC/PHY SW configuration started.
Even with this, it's better to just not rely on undocumented firmware
behavior which can change.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Print a netdev error when we hit a case in which a specific VLAN is
already configured on the port. While at it, change the already existing
netdev_warn into an _err for consistency purposes.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no restriction around the change of the MAC address on the
switch ports, thus declare the interface netdevs IFF_LIVE_ADDR_CHANGE
capable.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no point in updating the MAC address of a switch interface each
time the link state changes, this only needs to happen in case the
endpoint changes (the switch interface is [dis]connected from/to a MAC).
Just move the call to dpaa2_switch_port_set_mac_addr() under
DPSW_IRQ_EVENT_ENDPOINT_CHANGED.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/intel/iavf/iavf_ethtool.c
3a0b5a2929fd ("iavf: Introduce new state machines for flow director")
95260816b489 ("iavf: use iavf_schedule_aq_request() helper")
https://lore.kernel.org/all/84e12519-04dc-bd80-bc34-8cf50d7898ce@intel.com/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
c13e268c0768 ("bnxt_en: Fix HWTSTAMP_FILTER_ALL packet timestamp logic")
c2f8063309da ("bnxt_en: Refactor RX VLAN acceleration logic.")
a7445d69809f ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
1c7fd6ee2fe4 ("bnxt_en: Rename some macros for the P5 chips")
https://lore.kernel.org/all/20231211110022.27926ad9@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
bd6781c18cb5 ("bnxt_en: Fix wrong return value check in bnxt_close_nic()")
84793a499578 ("bnxt_en: Skip nic close/open when configuring tstamp filters")
https://lore.kernel.org/all/20231214113041.3a0c003c@canb.auug.org.au/
drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c
3d7a3f2612d7 ("net/mlx5: Nack sync reset request when HotPlug is enabled")
cecf44ea1a1f ("net/mlx5: Allow sync reset flow when BF MGT interface device is present")
https://lore.kernel.org/all/20231211110328.76c925af@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with commit 4e51bf44a03a ("net: bridge: move the switchdev
object replay helpers to "push" mode") the switchdev_bridge_port_offload()
helper was extended with the intention to provide switchdev drivers easy
access to object addition and deletion replays. This works by calling
the replay helpers with non-NULL notifier blocks.
In the same commit, the dpaa2-switch driver was updated so that it
passes valid notifier blocks to the helper. At that moment, no
regression was identified through testing.
In the meantime, the blamed commit changed the behavior in terms of
which ports get hit by the replay. Before this commit, only the initial
port which identified itself as offloaded through
switchdev_bridge_port_offload() got a replay of all port objects and
FDBs. After this, the newly joining port will trigger a replay of
objects on all bridge ports and on the bridge itself.
This behavior leads to errors in dpaa2_switch_port_vlans_add() when a
VLAN gets installed on the same interface multiple times.
The intended mechanism to address this is to pass a non-NULL ctx to the
switchdev_bridge_port_offload() helper and then check it against the
port's private structure. But since the driver does not have any use for
the replayed port objects and FDBs until it gains support for LAG
offload, it's better to fix the issue by reverting the dpaa2-switch
driver to not ask for replay. The pointers will be added back when we
are prepared to ignore replays on unrelated ports.
Fixes: b28d580e2939 ("net: bridge: switchdev: replay all VLAN groups")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20231212164326.2753457-3-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The size of the DMA unmap was wrongly put as a sizeof of a pointer.
Change the value of the DMA unmap to be the actual macro used for the
allocation and the DMA map.
Fixes: 1110318d83e8 ("dpaa2-switch: add tc flower hardware offload on ingress traffic")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20231212164326.2753457-2-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The old implementation extracted VLAN TCI info from the payload
before the VLAN tag has been pushed in the payload.
Another problem was that the VLAN TCI was extracted even if the
packet did not have VLAN protocol header.
This resulted in invalid VLAN TCI and as a consequence a random
queue was computed.
This patch fixes the above issues and use the VLAN TCI from the
skb if it is present or VLAN TCI from payload if present. If no
VLAN header is present queue 0 is selected.
Fixes: 52c4a1a85f4b ("net: fec: add ndo_select_queue to fix TX bandwidth fluctuations")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The blamed commit added support for Rx copybreak. This meant that for
certain frame sizes, a new skb was allocated and the initial data buffer
was recycled. Instead of waiting to recycle the Rx buffer only after all
processing was done on it (like accessing the parse results or timestamp
information), the code path just went ahead and re-used the buffer right
away.
This sometimes lead to corrupted HW and SW annotation areas.
Fix this by delaying the moment when the buffer is recycled.
Fixes: 50f826999a80 ("dpaa2-eth: add rx copybreak support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.
Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.
Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.
This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
- 64 bytes for the software annotation area
- 64 bytes to account for a 64 byte aligned buffer address
Fixes: 6e2387e8f19e ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NETLINK_MAX_FMTMSG_LEN
NETLINK_MAX_FMTMSG_LEN is currently hardcoded to 80, and we provide an
error printf-formatted string having 96 characters including the
terminating \0. Assuming each %d (representing a queue) gets replaced by
a number having at most 2 digits (a reasonable assumption), the final
string is also 96 characters wide, which is too much.
Reduce the verbiage a bit by removing some (partially) redundant words,
which makes the new printf-formatted string be 73 characters wide with
the trailing newline.
Fixes: 800db2d125c2 ("net: enetc: ensure we always have a minimum number of TXQs for stack")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/lkml/202311061336.4dsWMT1h-lkp@intel.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231106160311.616118-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- get rid of the fake support for coherent DMA allocation on coldfire
with caches (Christoph Hellwig)
- add a few Kconfig dependencies so that Kconfig catches the use of
invalid configurations (Christoph Hellwig)
- fix a type in dma-debug output (Chuck Lever)
- rewrite a comment in swiotlb (Sean Christopherson)
* tag 'dma-mapping-6.7-2023-10-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: Fix a typo in a debugging eye-catcher
swiotlb: rewrite comment explaining why the source is preserved on DMA_FROM_DEVICE
m68k: remove unused includes from dma.c
m68k: don't provide arch_dma_alloc for nommu/coldfire
net: fec: use dma_alloc_noncoherent for data cache enabled coldfire
m68k: use the coherent DMA code for coldfire without data cache
dma-direct: warn when coherent allocations aren't supported
dma-direct: simplify the use atomic pool logic in dma_direct_alloc
dma-direct: add a CONFIG_ARCH_HAS_DMA_ALLOC symbol
dma-direct: add dependencies to CONFIG_DMA_GLOBAL_POOL
|
|
Coldfire platforms with data caches can't properly implement
dma_alloc_coherent and currently just return noncoherent memory from
dma_alloc_coherent.
The fec driver than works around this with a flush of all caches in the
receive path. Make this hack a little less bad by using the explicit
dma_alloc_noncoherent API and documenting the hacky cache flushes so
that the DMA API level hack can be removed.
Also replace the check for CONFIG_M532x for said hack with a check
for COLDFIRE && !COLDFIRE_COHERENT_DMA. While m532x is the only such
platform with a fec module, this makes the code more consistent and
easier to follow.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
|
|
All i.MX platforms (non-Coldfire) use DT nowadays, so their platform ID
entries can be removed.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231017063419.925266-3-alexander.stein@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
device_get_match_data() expects that of_device_id->data points to actual
fec_devinfo data, not a platform_device_id entry.
Fix this by adjusting OF device data pointers to their corresponding
structs.
enum imx_fec_type is now unused and can be removed.
Fixes: b0377116decd ("net: ethernet: Use device_get_match_data()")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231017063419.925266-2-alexander.stein@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert fman to use the .mac_get_caps() method rather than the
.validate() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/E1qsPkA-009wid-Kv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
ethtool_sprintf() is designed specifically for get_strings() usage.
Let's replace strncpy in favor of this more robust and easier to
understand interface.
Also, while we're here, let's change memcpy() over to ethtool_sprintf()
for consistency.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xdp_do_flush_map() is deprecated and new code should use xdp_do_flush()
instead.
Replace xdp_do_flush_map() with xdp_do_flush().
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: John Crispin <john@phrozen.org>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Cc: Shenwei Wang <shenwei.wang@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230908143215.869913-2-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct enetc_psfp_gate.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922172858.3822653-11-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct enetc_int_vector.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922172858.3822653-5-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking updates from Jakub Kicinski:
"Including fixes from netfilter and bpf.
Current release - regressions:
- eth: stmmac: fix failure to probe without MAC interface specified
Current release - new code bugs:
- docs: netlink: fix missing classic_netlink doc reference
Previous releases - regressions:
- deal with integer overflows in kmalloc_reserve()
- use sk_forward_alloc_get() in sk_get_meminfo()
- bpf_sk_storage: fix the missing uncharge in sk_omem_alloc
- fib: avoid warn splat in flow dissector after packet mangling
- skb_segment: call zero copy functions before using skbuff frags
- eth: sfc: check for zero length in EF10 RX prefix
Previous releases - always broken:
- af_unix: fix msg_controllen test in scm_pidfd_recv() for
MSG_CMSG_COMPAT
- xsk: fix xsk_build_skb() dereferencing possible ERR_PTR()
- netfilter:
- nft_exthdr: fix non-linear header modification
- xt_u32, xt_sctp: validate user space input
- nftables: exthdr: fix 4-byte stack OOB write
- nfnetlink_osf: avoid OOB read
- one more fix for the garbage collection work from last release
- igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
- bpf, sockmap: fix preempt_rt splat when using raw_spin_lock_t
- handshake: fix null-deref in handshake_nl_done_doit()
- ip: ignore dst hint for multipath routes to ensure packets are
hashed across the nexthops
- phy: micrel:
- correct bit assignments for cable test errata
- disable EEE according to the KSZ9477 errata
Misc:
- docs/bpf: document compile-once-run-everywhere (CO-RE) relocations
- Revert "net: macsec: preserve ingress frame ordering", it appears
to have been developed against an older kernel, problem doesn't
exist upstream"
* tag 'net-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()
Revert "net: team: do not use dynamic lockdep key"
net: hns3: remove GSO partial feature bit
net: hns3: fix the port information display when sfp is absent
net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
net: hns3: fix debugfs concurrency issue between kfree buffer and read
net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
net: hns3: Support query tx timeout threshold by debugfs
net: hns3: fix tx timeout issue
net: phy: Provide Module 4 KSZ9477 errata (DS80000754C)
netfilter: nf_tables: Unbreak audit log reset
netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for ip_set_hash_netportnet.c
netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
netfilter: nf_tables: uapi: Describe NFTA_RULE_CHAIN_ID
netfilter: nfnetlink_osf: avoid OOB read
netfilter: nftables: exthdr: fix 4-byte stack OOB write
selftests/bpf: Check bpf_sk_storage has uncharged sk_omem_alloc
bpf: bpf_sk_storage: Fix the missing uncharge in sk_omem_alloc
bpf: bpf_sk_storage: Fix invalid wait context lockdep report
s390/bpf: Pass through tail call counter in trampolines
...
|
|
enetc_psi_create() returns an ERR_PTR() or a valid station interface
pointer, but checking for the non-NULL quality of the return code blurs
that difference away. So if enetc_psi_create() fails, we call
enetc_psi_destroy() when we shouldn't. This will likely result in
crashes, since enetc_psi_create() cleans up everything after itself when
it returns an ERR_PTR().
Fixes: f0168042a212 ("net: enetc: reimplement RFS/RSS memory clearing as PCI quirk")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/netdev/582183ef-e03b-402b-8e2d-6d9bb3c83bd9@moroto.mountain/
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230906141609.247579-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add HOTPLUG_SMT support (/sys/devices/system/cpu/smt) and honour the
configured SMT state when hotplugging CPUs into the system
- Combine final TLB flush and lazy TLB mm shootdown IPIs when using the
Radix MMU to avoid a broadcast TLBIE flush on exit
- Drop the exclusion between ptrace/perf watchpoints, and drop the now
unused associated arch hooks
- Add support for the "nohlt" command line option to disable CPU idle
- Add support for -fpatchable-function-entry for ftrace, with GCC >=
13.1
- Rework memory block size determination, and support 256MB size on
systems with GPUs that have hotpluggable memory
- Various other small features and fixes
Thanks to Andrew Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Athira
Rajeev, Benjamin Gray, Christophe Leroy, Frederic Barrat, Gautam
Menghani, Geoff Levand, Hari Bathini, Immad Mir, Jialin Zhang, Joel
Stanley, Jordan Niethe, Justin Stitt, Kajol Jain, Kees Cook, Krzysztof
Kozlowski, Laurent Dufour, Liang He, Linus Walleij, Mahesh Salgaonkar,
Masahiro Yamada, Michal Suchanek, Nageswara R Sastry, Nathan Chancellor,
Nathan Lynch, Naveen N Rao, Nicholas Piggin, Nick Desaulniers, Omar
Sandoval, Randy Dunlap, Reza Arbab, Rob Herring, Russell Currey, Sourabh
Jain, Thomas Gleixner, Trevor Woerner, Uwe Kleine-König, Vaibhav Jain,
Xiongfeng Wang, Yuan Tan, Zhang Rui, and Zheng Zengkai.
* tag 'powerpc-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (135 commits)
macintosh/ams: linux/platform_device.h is needed
powerpc/xmon: Reapply "Relax frame size for clang"
powerpc/mm/book3s64: Use 256M as the upper limit with coherent device memory attached
powerpc/mm/book3s64: Fix build error with SPARSEMEM disabled
powerpc/iommu: Fix notifiers being shared by PCI and VIO buses
powerpc/mpc5xxx: Add missing fwnode_handle_put()
powerpc/config: Disable SLAB_DEBUG_ON in skiroot
powerpc/pseries: Remove unused hcall tracing instruction
powerpc/pseries: Fix hcall tracepoints with JUMP_LABEL=n
powerpc: dts: add missing space before {
powerpc/eeh: Use pci_dev_id() to simplify the code
powerpc/64s: Move CPU -mtune options into Kconfig
powerpc/powermac: Fix unused function warning
powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
powerpc: Don't include lppaca.h in paca.h
powerpc/pseries: Move hcall_vphn() prototype into vphn.h
powerpc/pseries: Move VPHN constants into vphn.h
cxl: Drop unused detach_spa()
powerpc: Drop zalloc_maybe_bootmem()
powerpc/powernv: Use struct opal_prd_msg in more places
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull modules updates from Luis Chamberlain:
"Summary of the changes worth highlighting from most interesting to
boring below:
- Christoph Hellwig's symbol_get() fix to Nvidia's efforts to
circumvent the protection he put in place in year 2020 to prevent
proprietary modules from using GPL only symbols, and also ensuring
proprietary modules which export symbols grandfather their taint.
That was done through year 2020 commit 262e6ae7081d ("modules:
inherit TAINT_PROPRIETARY_MODULE"). Christoph's new fix is done by
clarifing __symbol_get() was only ever intended to prevent module
reference loops by Linux kernel modules and so making it only find
symbols exported via EXPORT_SYMBOL_GPL(). The circumvention tactic
used by Nvidia was to use symbol_get() to purposely swift through
proprietary module symbols and completely bypass our traditional
EXPORT_SYMBOL*() annotations and community agreed upon
restrictions.
A small set of preamble patches fix up a few symbols which just
needed adjusting for this on two modules, the rtc ds1685 and the
networking enetc module. Two other modules just needed some build
fixing and removal of use of __symbol_get() as they can't ever be
modular, as was done by Arnd on the ARM pxa module and Christoph
did on the mmc au1xmmc driver.
This is a good reminder to us that symbol_get() is just a hack to
address things which should be fixed through Kconfig at build time
as was done in the later patches, and so ultimately it should just
go.
- Extremely late minor fix for old module layout 055f23b74b20
("module: check for exit sections in layout_sections() instead of
module_init_section()") by James Morse for arm64. Note that this
layout thing is old, it is *not* Song Liu's commit ac3b43283923
("module: replace module_layout with module_memory"). The issue
however is very odd to run into and so there was no hurry to get
this in fast.
- Although the fix did not go through the modules tree I'd like to
highlight the fix by Peter Zijlstra in commit 54097309620e
("x86/static_call: Fix __static_call_fixup()") now merged in your
tree which came out of what was originally suspected to be a
fallout of the the newer module layout changes by Song Liu commit
ac3b43283923 ("module: replace module_layout with module_memory")
instead of module_init_section()"). Thanks to the report by
Christian Bricart and the debugging by Song Liu & Peter that turned
to be noted as a kernel regression in place since v5.19 through
commit ee88d363d156 ("x86,static_call: Use alternative RET
encoding").
I highlight this to reflect and clarify that we haven't seen more
fallout from ac3b43283923 ("module: replace module_layout with
module_memory").
- RISC-V toolchain got mapping symbol support which prefix symbols
with "$" to help with alignment considerations for disassembly.
This is used to differentiate between incompatible instruction
encodings when disassembling. RISC-V just matches what ARM/AARCH64
did for alignment considerations and Palmer Dabbelt extended
is_mapping_symbol() to accept these symbols for RISC-V. We already
had support for this for all architectures but it also checked for
the second character, the RISC-V check Dabbelt added was just for
the "$". After a bit of testing and fallout on linux-next and based
on feedback from Masahiro Yamada it was decided to simplify the
check and treat the first char "$" as unique for all architectures,
and so we no make is_mapping_symbol() for all archs if the symbol
starts with "$".
The most relevant commit for this for RISC-V on binutils was:
https://sourceware.org/pipermail/binutils/2021-July/117350.html
- A late fix by Andrea Righi (today) to make module zstd
decompression use vmalloc() instead of kmalloc() to account for
large compressed modules. I suspect we'll see similar things for
other decompression algorithms soon.
- samples/hw_breakpoint minor fixes by Rong Tao, Arnd Bergmann and
Chen Jiahao"
* tag 'modules-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module/decompress: use vmalloc() for zstd decompression workspace
kallsyms: Add more debug output for selftest
ARM: module: Use module_init_layout_section() to spot init sections
arm64: module: Use module_init_layout_section() to spot init sections
module: Expose module_init_layout_section()
modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules
rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff
net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index
mmc: au1xmmc: force non-modular build and remove symbol_get usage
ARM: pxa: remove use of symbol_get()
samples/hw_breakpoint: mark sample_hbp as static
samples/hw_breakpoint: fix building without module unloading
samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'
modpost, kallsyms: Treat add '$'-prefixed symbols as mapping symbols
kernel: params: Remove unnecessary ‘0’ values from err
module: Ignore RISC-V mapping symbols too
|
|
The FEC driver supports the statistics for XDP actions except for
XDP_TX before, because the XDP_TX was not supported when adding
the statistics for XDP. Now the FEC driver has supported XDP_TX
since commit f601899e4321 ("net: fec: add XDP_TX feature support").
So it's reasonable and necessary to add statistics for XDP_TX.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we already added the exception tracing for XDP_TX, I think it is
necessary to add the exception tracing for other XDP actions, such
as XDP_REDIRECT, XDP_ABORTED and unknown error actions.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230822065255.606739-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 5d93cfcf7360 ("net: dpaa: Convert to phylink") removed
fman_set_mac_active_pause()/fman_get_pause_cfg() but not declarations.
Commit 48257c4f168e ("Add fs_enet ethernet network driver, for several
embedded platforms.") declared but never implemented
fs_enet_platform_init() and fs_enet_platform_cleanup().
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230817134159.38484-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the "budget" is passed into fec_enet_tx_queue(), one
optimization we can do is to use napi_consume_skb() to instead
of dev_kfree_skb_any().
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Alexander H Duyck <alexander.duyck@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230816090242.463822-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SIU_INT_IRQ1 is not used anywhere and __IO_BASE is defined in
asm/io.h
Remove m82xx_pci.h
Then the only thing remaining in mpc8260.h is MPC82XX_BCR_PLDP
Move MPC82XX_BCR_PLDP into asm/cpm2.h then remove mpc8260.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/afe23bf3624c389ff17e9789884c78c124b7b202.1691474658.git.christophe.leroy@csgroup.eu
|
