| Age | Commit message (Collapse) | Author |
|---|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
35d92abfbad8 ("net: hns3: fix kernel crash when devlink reload during initialization")
2a1a1a7b5fd7 ("net: hns3: add command queue trace for hns3")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The devlink reload process will access the hardware resources,
but the register operation is done before the hardware is initialized.
So, processing the devlink reload during initialization may lead to kernel
crash.
This patch fixes this by registering the devlink after
hardware initialization.
Fixes: cd6242991d2e ("net: hns3: add support for registering devlink for VF")
Fixes: 93305b77ffcb ("net: hns3: fix kernel crash when devlink reload during pf initialization")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to hardware limitation, for device support modify
VLAN filter state but not support bypass port VLAN filter,
it should always disable the port VLAN filter. but the driver
enables port VLAN filter when initializing, if there is no
VLAN(except VLAN 0) id added, the driver will disable it
in service task. In most time, it works fine. But there is
a time window before the service task shceduled and net device
being registered. So if user adds VLAN at this time, the driver
will not update the VLAN filter state, and the port VLAN filter
remains enabled.
To fix the problem, if support modify VLAN filter state but not
support bypass port VLAN filter, set the port vlan filter to "off".
Fixes: 184cd221a863 ("net: hns3: disable port VLAN filter when support function level VLAN filter control")
Fixes: 2ba306627f59 ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a memory barrier in followed case. When set the port down,
hclgevf_set_timmer will set DOWN in state. Meanwhile, the service task has
different behaviour based on whether the state is DOWN. Thus, to make sure
service task see DOWN, use smp_mb__after_atomic after calling set_bit().
CPU0 CPU1
========================== ===================================
hclgevf_set_timer_task() hclgevf_periodic_service_task()
set_bit(DOWN,state) test_bit(DOWN,state)
pf also has this issue.
Fixes: ff200099d271 ("net: hns3: remove unnecessary work in hclgevf_main")
Fixes: 1c6dfe6fc6f7 ("net: hns3: remove mailbox and reset work in hclge_main")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
During the PF initialization process, hclge_update_port_info may return an
error code for some reason. At this point, the ptp initialization has been
completed. To void memory leaks, the resources that are applied by ptp
should be released. Therefore, when hclge_update_port_info returns an error
code, hclge_ptp_uninit is called to release the corresponding resources.
Fixes: eaf83ae59e18 ("net: hns3: add querying fec ability from firmware")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It provides nodemask_t to describe the numa node mask in kernel. To
improve transportability, change the type of numa_node_mask as nodemask_t.
Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a reset occurring, it's supposed to recover user's configuration.
Currently, the port info(speed, duplex and autoneg) is stored in hclge_mac
and will be scheduled updated. Consider the case that reset was happened
consecutively. During the first reset, the port info is configured with
a temporary value cause the PHY is reset and looking for best link config.
Second reset start and use pervious configuration which is not the user's.
The specific process is as follows:
+------+ +----+ +----+
| USER | | PF | | HW |
+---+--+ +-+--+ +-+--+
| ethtool --reset | |
+------------------->| reset command |
| ethtool --reset +-------------------->|
+------------------->| +---+
| +---+ | |
| | |reset currently | | HW RESET
| | |and wait to do | |
| |<--+ | |
| | send pervious cfg |<--+
| | (1000M FULL AN_ON) |
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | reset command |<--+
| +-------------------->|
| | +---+
| | send pervious cfg | | HW RESET
| | (10M HALF AN_OFF) |<--+
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | | |
| | read cfg(time task) |<--+
| | (10M HALF AN_OFF) |
| |<--------------------+
| | |
v v v
To avoid aboved situation, this patch introduced req_speed, req_duplex,
req_autoneg to store user's configuration and it only be used after
hardware reset and to recover user's configuration
Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Also propagate extack to hclge_get_cls_key_ip(), and convert it to
return error code.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20240422152717.175659-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to query scc version by devlink info for device V3.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20240410125354.2177067-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to dump command queue trace for hns3.
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20240410125354.2177067-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The devlink reload process will access the hardware resources,
but the register operation is done before the hardware is initialized.
So, processing the devlink reload during initialization may lead to kernel
crash. This patch fixes this by taking devl_lock during initialization.
Fixes: b741269b2759 ("net: hns3: add support for registering devlink for PF")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b7e ("net: hns3: Only update mac configuation when necessary")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the tc is removed during reset, hns3 driver will return a errcode.
But kernel ignores this errcode, As a result,
the driver status is inconsistent with the kernel status.
This patch retains the deletion status when the deletion fails
and continues to delete after the reset to ensure that
the status of the driver is consistent with that of kernel.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the hilink version is H60, the serdes serial loopback test is not
supported. This patch add hilink version detection. When the version
is H60, the serdes serial loopback test will be disable.
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hisilicon device now supports a new 200G link interface,
which query from firmware in a new bit. Therefore,
the HCLGE_SUPPORT_200G_R4_BIT capability bit has been added.
The HCLGE_SUPPORT_200G_BIT has been renamed as
HCLGE_SUPPORT_200G_R4_EXT_BIT, and the firmware has
extended support for this mode.
Fixes: ae6f010cb1a7 ("net: hns3: add support for 200G device")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If PF is down, firmware will returns 10 Mbit/s rate and half-duplex mode
when PF queries the port information from firmware.
After imp reset command is executed, PF status changes to down,
and PF will query link status and updates port information
from firmware in a periodic scheduled task.
However, there is a low probability that port information is updated
when PF is down, and then PF link status changes to up.
In this case, PF synchronizes incorrect rate and duplex mode to VF.
This patch fixes it by updating port information before
PF synchronizes the rate and duplex to the VF
when PF changes to up.
Fixes: 18b6e31f8bf4 ("net: hns3: PF add support for pushing link status to VFs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the FEC capability bit is default set for device version V2.
It's incorrect for the copper port. Eventhough it doesn't make the nic
work abnormal, but the capability information display in debugfs may
confuse user. So clear it when driver get the port type inforamtion.
Fixes: 433ccce83504 ("net: hns3: use FEC capability queried from firmware")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hclge_sync_vlan_filter is called in periodic task,
trying to remove VLAN from vlan_del_fail_bmap. It can
be concurrence with VLAN adding operation from user.
So once user failed to delete a VLAN id, and add it
again soon, it may be removed by the periodic task,
which may cause the software configuration being
inconsistent with hardware. So add mutex handling
to avoid this.
user hns3 driver
periodic task
│
add vlan 10 ───── hns3_vlan_rx_add_vid │
│ (suppose success) │
│ │
del vlan 10 ───── hns3_vlan_rx_kill_vid │
│ (suppose fail,add to │
│ vlan_del_fail_bmap) │
│ │
add vlan 10 ───── hns3_vlan_rx_add_vid │
(suppose success) │
foreach vlan_del_fail_bmp
del vlan 10
Fixes: fe4144d47eef ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add HCLGE_SUPPORT_50G_R1_BIT and HCLGE_SUPPORT_100G_R2_BIT two
capability bits and Corresponding link modes.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently hns3 driver supports vf fault detect feature. Several ras caused
by VF resources don't need to do PF function reset for recovery. The driver
only needs to reset the specified VF.
So this patch adds process in ras module. New process will get detailed
information about ras and do the most correct measures based on these
accurate information.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20231007031215.1067758-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. we think firmware watchdog initialization is completed
before hns3 clear the firmware interrupt source. However, firmware
initialization may not complete early.
so we add delay before hns3 clear firmware interrupt source and 5 ms delay
is enough to avoid second firmware reset interrupt.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Firmware does not respond driver commands during reset
Therefore, rule will fail to delete while the firmware is resetting
So, if failed to delete rule, set rule state to TO_DEL,
and the rule will be deleted when periodic task being scheduled.
Fixes: 0205ec041ec6 ("net: hns3: add support for hw tc offload of tc flower")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the driver will enable unicast promisc for the function
once configure mac address fail. It's unreasonable when the failure
is caused by using same mac address with other functions. So only
enable unicast promisc when mac table full.
Fixes: c631c696823c ("net: hns3: refactor the promisc mode setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We hope that tc qdisc and dcb ets commands can not be used crosswise.
If we want to use any of the commands to configure tc,
We must use the other command to clear the existing configuration.
However, when we configure a single tc with tc qdisc,
we can still configure it with dcb ets.
Because we use mqprio_active as the tag of tc qdisc configuration,
but with dcb ets, we do not check mqprio_active.
This patch fix this issue by check mqprio_active before
executing the dcb ets command. and add dcb_ets_active to
replace HCLGE_FLAG_DCB_ENABLE and HCLGE_FLAG_MQPRIO_ENABLE
at the hclge layer,
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the original RPU query command, the status register values of
multiple RPU tunnels are accumulated by default, which is unreasonable.
This patch Fix it by querying the specified tunnel ID.
The tunnel number of the device can be obtained from firmware
during initialization.
Fixes: ddb54554fa51 ("net: hns3: add DFX registers information for ethtool -d")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dump register function is being refactored.
The first step in refactoring is put the dump regs function
into a separate file.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/intel/igc/igc_main.c
06b412589eef ("igc: Add lock to safeguard global Qbv variables")
d3750076d464 ("igc: Add TransmissionOverrun counter")
drivers/net/ethernet/microsoft/mana/mana_en.c
a7dfeda6fdec ("net: mana: Fix MANA VF unload when hardware is unresponsive")
a9ca9f9ceff3 ("page_pool: split types and declarations from page_pool.h")
92272ec4107e ("eth: add missing xdp.h includes in drivers")
net/mptcp/protocol.h
511b90e39250 ("mptcp: fix disconnect vs accept race")
b8dc6d6ce931 ("mptcp: fix rcv buffer auto-tuning")
tools/testing/selftests/net/mptcp/mptcp_join.sh
c8c101ae390a ("selftests: mptcp: join: fix 'implicit EP' test")
03668c65d153 ("selftests: mptcp: join: rework detailed report")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In some configure flow of hns3 driver, for example, change mtu, it will
disable MAC through firmware before configuration. But firmware disables
MAC asynchronously. The rx traffic may be not stopped in this case.
So fixes it by waiting until mac link is down.
Fixes: a9775bb64aa7 ("net: hns3: fix set and get link ksettings issue")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some nic configurations could only be performed after link is down. So this
patch refactor this API for reuse.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Restore the mac pause state to user configuration when autoneg is disabled
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.
This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions in the hns3 driver have unused parameters.
The compiler will warn about them when building
with -Wunused-parameter option of hns3.
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 35d93a30040c ("net: hns3: adjust the process of PF reset")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HNS3 driver supports Wake-on-LAN, which can wake up
the server from power off state to power on state by magic
packet or magic security packet.
ChangeLog:
v1->v2:
Deleted the debugfs function that overlaps with the ethtool function
from suggestion of Andrew Lunn.
v2->v3:
Return the wol configuration stored in driver,
suggested by Alexander H Duyck.
v3->v4:
Add a helper to go from netdev to the local struct,
suggested by Simon Horman and Jakub Kicinski.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the PF check the VF alive by the KEEP_ALVE
mailbox from VF. VF keep sending the mailbox per 2
seconds. Once PF lost the mailbox for more than 8
seconds, it will regards the VF is abnormal, and stop
notifying the state change to VF, include link state,
vf mac, reset, even though it receives the KEEP_ALIVE
mailbox again. It's inreasonable.
This patch fixes it. PF will record the state change which
need to notify VF when lost the VF's KEEP_ALIVE mailbox.
And notify VF when receive the mailbox again. Introduce a
new flag HCLGE_VPORT_STATE_INITED, used to distinguish the
case whether VF driver loaded or not. For VF will query
these states when initializing, so it's unnecessary to
notify it in this case.
Fixes: aa5c4f175be6 ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, it missed set HCLGE_VPORT_STATE_PROMISC_CHANGE
flag for VF when vport->overflow_promisc_flags changed.
So the VF won't check whether to update promisc mode in
this case. So add it.
Fixes: 1e6e76101fd9 ("net: hns3: configure promisc mode for VF asynchronously")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
resetting process
Currently, if driver is in phy-imp(phy controlled by imp firmware) mode, as
driver did not update phy link ksettings after initialization process or
not update advertising when getting phy link ksettings from firmware, it
may set incorrect phy link ksettings for firmware in resetting process.
So fix it.
Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs")
Fixes: c5ef83cbb1e9 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config")
Fixes: 2312e050f42b ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the HNS3 driver reports the rss hash type
of each packet based on the rss hash tuples set. It
always reports PKT_HASH_TYPE_L4, without checking the
type of current packet. It's incorrect.
Fixes it by reporting it base on the packet type.
Fixes: 796640778c26 ("net: hns3: support RXD advanced layout")
Fixes: 232fc64b6e62 ("net: hns3: Add HW RSS hash information to RX skb")
Fixes: ea4858670717 ("net: hns3: handle the BD info on the last BD of the packet")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As the argument struct hnae3_handle *h of function hclge_get_dscp_prio()
can be other client registered in hnae3 layer, we need to transform it
into hnae3_handle of local nic client to get right dscp settings for
other clients.
Fixes: dfea275e06c2 ("net: hns3: optimize converting dscp to priority process of hns3_nic_select_queue()")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing __init/__exit annotations to module init/exit funcs.
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Link: https://lore.kernel.org/r/20220917082118.7971-1-xiujianfeng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, driver will always clear user defined field of flow director
in uninit process and sync flow director table in periodic task. However,
if hardware does not support flow director driver should not do those
processes, so add fd ability judgement.
The fd ability judgement in function hclge_clear_fd_rules_in_list() is
redundant, so delete it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
hns3_nic_select_queue()
Currently, when function hns3_nic_select_queue() converts dscp to priority,
it calls an indirect callback ae_algo->ops->get_dscp_prio to get priority.
However as function hns3_nic_select_queue() is in fast path, the indirect
call may cause degradation of performance. For optimization, this patch
moves dscp_app_cnt and dscp_prio from struct hclge_tm_info to struct
hnae3_knic_private_info, so they can be used in both hclge and hns3 layers.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch add support for external loopback test.
The successful test need the link is up with duplex full. The
driver do external loopback first, and then the whole offline
test.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When serdes lane support setting 25Gb/s or 50Gb/s speed and user wants to
set port speed as 50Gb/s, it can be setted as one 50Gb/s serdes lane or
two 25Gb/s serdes lanes.
So, this patch adds support to query and set lane number by ethtool
to satisfy this scenario.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FEC statistics can be used to check the transmission quality of links.
This patch implements the get_fec_stats callback of ethtool_ops to support
querying FEC statistics by command "ethtool -I --show-fec eth0".
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support config dscp map to tc by implementing ieee_setapp
and ieee_delapp of struct dcbnl_rtnl_ops. Driver will convert mapping
relationship from dscp-prio to dscp-tc.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some new devices, the FEC mode can not be set to OFF in speed 200G.
In order to flexibly adapt to all types of devices, driver queries
fec ability from firmware to decide whether OFF mode can be supported.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch supports llrs fec mode in speed 200G for some new devices, and
suppoprts querying llrs fec ability from firmware.
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some new devices, driver can queries fec ability from firmware to
decide which FEC mode can be supported.
If devices of old version which not support querying fec ability, driver
sets fixed ability according to current speed.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
