| Age | Commit message (Collapse) | Author |
|---|
|
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hclge_inform_reset_assert_to_vf()
In hclge_inform_reset_assert_to_vf(), variable reset_type(enum type)
will be copied into msg_data whose size is 2 bytes. Currently, hip08
is a little-endian machine, so the lower two bytes of reset_type will
be copied to msg_data. But when running on a big-endian machine,
msg_data will have a wrong value(the higher two bytes of reset_type).
So this patch modifies the type of reset_type to u16, and adds a
build check in case enum hnae3_reset_type has value larger than
U16_MAX.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mutex vport_cfg_mutex has been used to protect uc_mac_list,
mc_mac_list and vlan_list from being modified by unloading
or reset task at the same time. But now unloading will
set up HCLGE_STATE_REMOVING flag and call cancel_work_sync to
break down this race condition, so this mutex is unnecessary.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.
This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.
BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using '%d' for printing type unsigned int or '%u' for
type int would cause static tools to give false warnings,
so this patch cleanups this warning by using the suitable
format specifier of the type of variable.
BTW, modifies the type of some variables and macro to
synchronize with their usage.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code more readable, this patch replaces
some magic numbers with macro or sizeof operation.
Also uses macro lower_32_bits and upper_32_bits to
get bits 0-31 and 32-63 of a number, instead of
using type conversion and '>>' operation.
No functional change.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support of configuring VF MAC from the host
for the HNS3 driver.
BTW, the parameter init in the hns3_init_mac_addr is
unnecessary now, since the MAC address will not read from
NCL_CONFIG when doing reset, so it should be removed,
otherwise it will affect VF's MAC address initialization.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.
For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:
'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status
'ip link show'
show the setting status
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
To explain some code, this patch adds some comments, and modifies or
merges some comments to make them more neat.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When NCSI has HW error, the IMP will report this error to the driver
by sending a mailbox. After received this message, the driver should
assert a global reset to fix this kind of HW error.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All constant in 'enum HCLGE_MBX_OPCODE' start with HCLGE, except
'HLCGE_MBX_PUSH_VLAN_INFO' (C and L switched)
s/HLC/HCL/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If HCLGE_MBX_MAX_RESP_DATA_SIZE > HCLGE_MBX_MAX_RESP_DATA_SIZE,
the memcpy will cause out of memory. So this patch just set
resp_data_len to the maximum length for this case.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does following things:
1. add the keyword const before some variables which won't be modified
in functions.
2. changes some variables from signed to unsigned to avoid bitwise
operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
using an array which is harder to get the meaning of each element.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch deletes some redundant code and refactors some bloated
functions.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We trigger PF reset when a RAS error of NIC named over_8bd_nfe_err
occurred before. But it is possible that a VF causes that error, it's
reasonable to trigger VF reset instead of PF reset in this case.
This patch add detection of vf_id if a over_8bd_nfe_err occurs, if
vf_id is 0, we trigger PF reset. Otherwise, we will trigger VF reset
on the VF with error.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hclge_bind_ring_with_vector() fails,
hclge_map_unmap_ring_to_vf_vector() returns the error
directly, so nobody will free the memory allocated by
hclge_get_ring_chain_from_mbx().
So hclge_free_vector_ring_chain() should be called no matter
hclge_bind_ring_with_vector() fails or not.
Fixes: 84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.
The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes
In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
Indeed, ndo_set_vf_vlan() is expected to enable or disable port based
VLAN (hardware inserts a specified VLAN tag to all TX packets for a
specified VF) . When enable port based VLAN, we use port based VLAN id
as VLAN filter entry. When disable port based VLAN, we use VLAN id of
VLAN device.
This patch fixes it for PF, enable/disable port based VLAN when calls
ndo_set_vf_vlan().
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Method for obtaining the media type of the VF network port periodically,
regular tasks will not run until the network port UP. When the network
port is DOWN, the network port cannot obtain the media type.
Modifies the media type obtained when initializing the VF network port.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For revision 0x20, VF shares the same RSS config with PF.
In original codes, it always return 0 when query RSS hash
key for VF. This patch fixes it by return the hash key
got from PF.
Fixes: 374ad291762a ("net: hns3: net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the VF shares the same TC config as PF, the business
running on PF and VF must have samiliar module.
For simplicity, we are not considering VF sharing the same tc
configuration as PF use case, so this patch removes the support
of TC configuration from VF and forcing VF to just use single
TC.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF can receive packets of other functions when in promisc
mode. It's not safe, so don't allow VF to enable promisc
mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints queue map information.
debugfs command:
echo dump queue map > cmd
Sample Command:
root@(none)# echo queue map > cmd
local queue id | global queue id | vector id
0 32 769
1 33 770
2 34 771
3 35 772
4 36 773
5 37 774
6 38 775
7 39 776
8 40 777
9 41 778
10 42 779
11 43 780
12 44 781
13 45 782
14 46 783
15 47 784
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds mtu setting support for vf, currently
vf and pf share the same hardware mtu setting. Mtu set
by vf must be less than or equal to pf' mtu, and mtu
set by pf must be greater than or equal to vf' mtu.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.
This patch adds vport alive state checking support, in order
to support the above scenario.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the .reset_prepare and .reset_done
ops from pci framework to support the PF FLR.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.
Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.
Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.
This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.
Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.
hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For mta table support has been dropped, remove the code for mta table.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually, hclge_get_ring_chain_from_mbx is used to get ring type, tqp id,
and int_gl index from mailbox message. So the comments is incorrect. This
patch fixes it.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGE_INT_GL_IDX_M and HCLGE_INT_GL_IDX_S are used to set fireware
cmd. When getting int_gl value from mailbox message, we should use
HNAE3_RING_GL_IDX_M and HNAE3_RING_GL_IDX_S.
Fixes: 79eee4108541 ("net: hns3: add int_gl_idx setup for VF")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the update flow of the new PF driver, if a multicast address is in mta
table, the VF deletion action will not take effect.
This patch adds the VF adaptation according to the new flow of PF'driver.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Reviewed-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is not empty before reading the
message.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support of hardware rx-vlan-offload to VF driver.
VF uses mailbox to convey PF to configure the hardware.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two level of vlan tables in hardware, one is port vlan
which is shared by all functions, the other one is function
vlan table, each function has it's own function vlan table.
Currently, PF sets the port vlan table, and vf sets the function
vlan table, which will cause packet lost problem.
This patch fixes this problem by setting both vlan table, and
use hdev->vlan_table to manage thet port vlan table.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 2bfbd35d8ecd ("net: hns3: Changes required in PF mailbox to support VF reset")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF needs to assert the VF reset when it receives the request to
reset from VF. After receiving request PF ackknowledges the
request by replying back MBX_ASSERTING_RESET message to VF.
VF then goes to pending state and wait for hardware to complete
the reset.
This patch contains code to handle the received VF message, inform
the VF of assertion and reset the VF using cmdq interface.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for querying speed and duplex by ethtool ethX
to VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
