| Age | Commit message (Collapse) | Author |
|---|
|
It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
static int e1000e_pm_thaw(struct device *dev)
^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When changing the interface mtu, the driver starts with a value
that doesn't include VLAN_HLEN. Later tests in the driver
set the rx_buffer_len based on the mtu. As a result, when
the user increases the mtu to 1504 (to support 802.1AD for example),
the driver rx_buffer_len does not change and frames longer
the 1522 bytes are rejected as too long.
Include VLAN_HLEN from the start so that an user mtu greater then
1500 bytes is correctly reflected in the driver rx_buffer_len.
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit da1e2046e5, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function. The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.
After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values. This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.
The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.
Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
tx_hwtstamp_skb is always set before work is scheduled,
work is cancelled before tx_hwtstamp_skb is set to NULL.
PTP work cannot ever see tx_hwtstamp_skb set to NULL.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Hardware may fail to report time stamp e.g.:
- when hardware time stamping is not enabled
- when time stamp is requested shortly after ifup
Timeout time stamp reading work to prevent it from
scheduling itself indefinitely. Report timeout events
via system log and device stats.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost. It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.
Move the check back to the place it was before in the watchdog task. Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The commit 2800209994f8 (e1000e: Refactor PM flows) changed the
SET_SYSTEM_SLEEP_PM_OPS to open-coded assignment, but forgot to
protect them with CONFIG_PM_SLEEP. Then cause the following build
error when PM is disabled:
drivers/net/ethernet/intel/e1000e/netdev.c:7079:13:
error: 'e1000e_pm_suspend' undeclared here (not in a function)
.suspend = e1000e_pm_suspend,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7080:13:
error: 'e1000e_pm_resume' undeclared here (not in a function)
.resume = e1000e_pm_resume,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7082:11:
error: 'e1000e_pm_thaw' undeclared here (not in a function)
.thaw = e1000e_pm_thaw,
^
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previous commit c3a0dce35af0 fixed an overrun for the RAR on i218 devices.
This commit also attempted to homogenize the RAR/SHRA access for all parts
accessed by the e1000e driver. This change introduced an error for
assigning MAC addresses to guest OS's for 82579 devices.
Only RAR[0] is accessible to the driver for 82579 parts, and additional
addresses must be placed into the SHRA[L|H] registers. The rar_entry_count
was changed in the previous commit to an inaccurate value that accounted
for all RAR and SHRA registers, not just the ones usable by the driver.
This patch fixes the count to the correct value and adjusts the
e1000_rar_set_pch2lan() function to user the correct index.
Cc: John Greene <jogreene@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Changes to the rar_entry_count value require a change to the indexing
used to access the SHRA[H|L] registers when testing them with
'ethtool -t <iface> offline'
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Valid values for InterruptThrottleRate are 10-100000, or one of
0, 1, 3, 4. '2' is not valid. This is a legacy from the branching
from the e1000 driver code that e1000e was based from.
Prior to this patch, if the e1000e driver was loaded with a forced
invalid InterruptThrottleRate of '2', then no throttle rate would be
set and no error message generated.
Now, a message will be generated that an invalid value was used and the
value for InterruptThrottleRate will be set to the default value.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.
ULP is gated on the following conditions:
1) The hardware must support ULP. Currently this is only I218
devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
execution. ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
as these features are mutually-exclusive.
Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail. This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete, allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).
Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode. Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.
Added checks to disallow functions that should not be executed if the
device is currently runtime suspended
Make runtime_idle callback to use same deterministic behavior as the igb
driver.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.
Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.
Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.
Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Branding strings from recently released and soon to be released
hardware configurations that are supported by e1000e.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.
Change the copyright date for 2014.
Reformat the header comments to conform to kernel networking coding norms
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.
Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early. EEE initialization for 82579 will be done
in e1000e_update_phy_task.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On a ME enabled system with the cable out, the driver init flow would
generate an erroneous message indicating that resets were being blocked
by an active ME session. Cause was ME clearing the semaphore bit to
block further PHY resets for up to 50 msec during power-on/cycle. After
this interval, ME would re-set the bit and allow PHY resets.
To resolve this, change the flow of e1000e_phy_hw_reset_generic() to
utilize a delay and retry method. Poll the FWSM register to minimize
any extra time added to the flow. If the delay times out at 100ms
(checked in 10msec increments), then return the value E1000_BLK_PHY_RESET,
as this is the accurate state of the PHY. Attempting to alter just the
call to e1000e_phy_hw_reset_generic() in e1000_init_phy_workarounds_pchlan()
just caused the problem to move further down the flow.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Cleaning up some pointer references that are no longer necessary
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add lock in e1000e_phc_adjfreq to prevent concurrent changes to TIMINCA
and SYSTIMH/L.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7509963c703b (e1000e: Fix a compile flag mis-match for
suspend/resume) moved suspend and resume hooks to be available when
CONFIG_PM is set. However, it can be set even if CONFIG_PM_SLEEP is not set
causing following warnings to be emitted:
drivers/net/ethernet/intel/e1000e/netdev.c:6178:12: warning:
‘e1000_suspend’ defined but not used [-Wunused-function]
drivers/net/ethernet/intel/e1000e/netdev.c:6185:12: warning:
‘e1000_resume’ defined but not used [-Wunused-function]
To fix this make the hooks to be available only when CONFIG_PM_SLEEP is set
and remove CONFIG_PM wrapping from driver ops because this is already
handled by SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Aaron Brown <aaron.f.brown@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses a mis-match between the declaration and usage of
the e1000_suspend and e1000_resume functions. Previously, these
functions were declared in a CONFIG_PM_SLEEP wrapper, and then utilized
within a CONFIG_PM wrapper. Both the declaration and usage will now be
contained within CONFIG_PM wrappers.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is to fix a compiler warning of maybe-uininitialized-variable
that is generated from gcc when the -O3 flag is used. In the function
e1000_reset_hw_80003es2lan(), the variable krmn_reg_data is first given
a value by being passed to a register read function as a
pass-by-reference parameter. But, the return value of that read
function was never checked to see if the read failed and the variable
not given an initial value. The compiler was smart enough to spot
this. This patch is to check the return value for that read function
and return it, if an error occurs, without trying to utilize the value
in kmrn_reg_data.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is to fix a compiler warning of __bad_udelay due to a value
of >999 being passed as a parameter to udelay() in the function
e1000e_phy_has_link_generic(). This affects the gcc compiler when
it is given a flag of -O3 and the icc compiler.
This patch is also making the change from mdelay() to msleep() in the
same function, since it was determined though code inspection that this
function is never called in atomic context.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
|
|
e1000e_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it copies the configuration to
the e1000_adapter structure before validating it at all.
Change e1000e_config_hwtstamp() to take a pointer to the
hwstamp_config and to copy the config after validating it.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
|
|
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When copying the MAC RAR registers to PHY there is an error in the
calculation of the rar_entry_count, which causes a write of unknown/
undefined register space in the MAC to unknown/undefined register space in
the PHY.
This patch fixes the overrun with writing to the PHY RAR and also fixes the
ethtool offline register tests so that the correctly addressed registers
have the appropriate bitmasks for R/W and RO bits for affected parts.
Shawn Rader gets credit for finding and fixing the register overrun.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
CC: Shawn Rader <shawn.t.rader@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Removing a comparison to the boolean value true where simply interrogating
the lvalue will produce the same result.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Steven (cc-ed) noticed an imbalance in semaphore put/get for
82573-based NICs. Don't we need something like the following
(untested) patch?
Signed-off-by: Steven La <sla@riverbed.com>
Acked-by: Arthur Kepner <akepner@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARNING:JIFFIES_COMPARISON: Comparing jiffies is almost always wrong;
prefer time_after, time_before and friends
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
While doing shutdown on the PCI device, the corresponding callback
function e1000e_shutdown() is trying to clear those correctable
errors on the upstream P2P bridge. Unfortunately, we don't have
the upstream P2P bridge under some cases (e.g. PCI-passthrou for
KVM on Power). That leads to kernel crash eventually.
The patch adds one more check on that to avoid kernel crash.
Signed-off-by: Li Zhang <zhlcindy@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch attempts to work around a problem found with some systems where
the call to pci_diable_link_state_locked() fails. As a result, ASPM is not,
in fact, disabled. Changing disable ASPM code to check if state actually
is disabled after the call and, if not, try another way to disable it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit (c96ddb0b e1000e: Use marco instead of digit for defining
e1000_rx_desc_packet_split) moved a define from one file to another but
missed using proper indentation/whitespace.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The initialization of the PHY on I217/I218, while similar to 82579, must
also check to see if the MAC and PHY are in the same mode (PCIe vs. SMBus)
otherwise the PHY will be inaccessible by the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
