| Age | Commit message (Collapse) | Author |
|---|
|
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E810-T adapters have two external bidirectional SMA connectors and two
internal unidirectional U.FL connectors. Multiplexing between U.FL and
SMA and SMA direction is controlled using the PCA9575 expander.
Add support for the PCA9575 detection and control of the respective pins
of the SMA/U.FL multiplexer using the GPIO AQ API.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement ice_aq_get_gpio and ice_aq_set_gpio for reading and changing
the state of GPIO pins described in the topology.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Separate link topo parameters in struct ice_aqc_link_topo_addr into
new struct ice_aqc_link_topo_params.
This keeps input parameters for the get_link_topo command in a separate
structure and is required by future commands that operate only on link
topo params without the node handle.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add code to manage recipes and profiles on admin queue layer.
Allow the driver to add a new recipe and update an existing one. Get a
recipe and get a recipe to profile association is mostly used in update
existing recipes code.
Only default recipes can be updated. An update is done by reading recipes
from HW, changing their params and calling add recipe command.
Support following admin queue commands:
- ice_aqc_opc_add_recipe (0x0290) - create a recipe with protocol
header information and other details that determine how this recipe
filter works
- ice_aqc_opc_recipe_to_profile (0x0291) - associate a switch recipe
to a profile
- ice_aqc_opc_get_recipe (0x0292) - get details of an existing recipe
- ice_aqc_opc_get_recipe_to_profile (0x0293) - get a recipe associated
with profile ID
Define ICE_AQC_RES_TYPE_RECIPE resource type to hold a switch
recipe. It is needed when a new switch recipe needs to be created.
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Grishma Kotecha <grishma.kotecha@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.
The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mode,
apply the default config for that mode, and apply
the received mapping.
Only one such mapping will be allowed per DSCP value,
and when the last DSCP mapping is deleted, the PF
will switch back into L2 VLAN QoS mode, applying the
appropriate default QoS settings.
L3 DSCP QoS mode will only be allowed in SW DCBx
mode, in other words, when the FW LLDP engine is
disabled. Commands that break this mutual exclusivity
will be blocked.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.
When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.
To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.
Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including
For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any
For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled
Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o
This information will be used in a future change to have the function
driver enable PTP hardware clock support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The following is reported by checkpatch, correct it.
-----------------------------------------------
drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
-----------------------------------------------
WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...
FILE: drivers/net/ethernet/intel/ice/ice_adminq_cmd.h:1428:
+/*
+ * Send to PF command (indirect 0x0801) ID is only used by PF
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
|
|
There are two package versions in the package binary. Today, these two
version numbers are the same. However, in the future that may change.
Update code to use the package info from the ice segment metadata
section, which is the package information that is actually downloaded to
the firmware during the download package process.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is an issue with some NVMs where an already existent LLDP
filter is blocking the creation of a filter to allow LLDP packets
to be redirected to the default VSI for the interface. This is
blocking all LLDP functionality based in the kernel when the FW
LLDP agent is disabled (e.g. software based DCBx).
Implement the new AQ command to allow adding VSI destinations to
existent filters on NVM versions that support the new command.
The new lldp_fltr_ctrl AQ command supports Rx filters only, so the
code flow for adding filters to disable Tx of control frames will
remain intact.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
set_rss_lut can fail due to incorrect vsi_id mask. vsi_id is 10 bit
but mask was 0x1FF whereas it should be 0x3FF.
For vsi_num >= 512, FW set_rss_lut can fail with return code
EACCESS (VSI ownership issue) because software was providing
incorrect vsi_num (dropping 10th bit due to incorrect mask) for
set_rss_lut admin command
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The manage MAC write command was implemented in an overly complex way
that actually didn't work, as it wasn't symmetric to the manage MAC
read command, and was feeding bytes out of order to the firmware. Fix
the implementation by just using a simple array to represent the MAC
address when it is being written via firmware command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.
Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.
Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.
Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.
Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.
Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Self-explanatory.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The flash memory for the ice hardware contains a block of information
used for link management called the Netlist module.
As this essentially represents another section of firmware, add its
version information to the output of the driver's .info_get handler.
This includes both a version and the first few bytes of a hash of the
module contents.
fw.netlist -> the version information extracted from the netlist module
fw.netlist.build-> first 4 bytes of the hash of the contents, similar
to fw.mgmt.build
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When reading from the NVM using a flat address, it is useful to know the
upper bound on the size of the flash contents. This value is not stored
within the NVM.
We can determine the size by performing a bisection between upper and
lower bounds. It is known that the size cannot exceed 16 MB (offset of
0xFFFFFF).
Use a while loop to bisect the upper and lower bounds by reading one
byte at a time. On a failed read, lower the maximum bound. On
a successful read, increase the lower bound.
Save this as the flash_size in the ice_nvm_info structure that contains
data related to the NVM.
The size will be used in a future patch for implementing full NVM read
via ethtool's GEEPROM command.
The maximum possible size for the flash is bounded by the size limit for
the NVM AdminQ commands. Add a new macro, ICE_AQC_NVM_MAX_OFFSET, which
can be used to represent this upper bound.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The NVM contents are read via firmware by using the ice_aq_read_nvm
function. This function has a couple of limits:
1) The AdminQ commands can only take buffers sized up to 4Kb. Thus, any
larger read must be split into multiple reads.
2) when reading from the Shadow RAM, reads must not cross sector
boundaries. The sectors are also 4Kb in size.
Implement the ice_read_flat_nvm function to read portions of the NVM by
flat offset. That is, to read using offsets from the start of the NVM
rather than from a specific module.
This function will be able to read both from the NVM and from the Shadow
RAM. For simplicity NVM reads will always be broken up to not cross 4Kb
page boundaries, even though this is not required unless reading from
the Shadow RAM.
Use this new function as the implementation of ice_read_sr_word_aq.
The ice_read_sr_buf_aq function is not modified here. This is because
a following change will remove the only caller of that function in favor
of directly using ice_read_flat_nvm. Thus, there is little benefit to
changing it now only to remove it momentarily. At the same time, the
ice_read_sr_aq function will also be removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.
The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Write the hardware tables based on the populated software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Store the TCAM entry with the profile data and the VSI group in the
respective SW structures. This will be subsequently used to write out
the tables to hardware.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Create an extraction sequence based on the packet header protocols to be
programmed and allocate a flow profile for the extraction sequence.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Print message to inform user if unsupported module is inserted, and
extend the topology / configuration detection.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
