| Age | Commit message (Collapse) | Author |
|---|
|
When spawning VFs in switchdev mode, internal filter list of VSIs is
cleared, which includes MAC rules. However MAC entries stay on netdev's
multicast list, which causes error message when bringing link up after
spawning VFs ("Failed to delete MAC filters"). __dev_mc_sync() is
called and tries to unsync addresses that were already removed
internally when adding VFs.
This can be reproduced with:
1) Load ice driver
2) Change PF to switchdev mode
3) Bring PF link up
4) Bring PF link down
5) Create a VF on PF
6) Bring PF link up
Added clearing of netdev's multicast (and also unicast) list when
spawning VFs in switchdev mode, so the state of internal rule list and
netdev's MAC list is consistent.
Fixes: 1a1c40df2e80 ("ice: set and release switchdev environment")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add tc-flower support for VF port representor devices.
Implement ndo_setup_tc callback for TC HW offload on VF port representors
devices. Implemented both methods: add and delete tc-flower flows.
Mark NETIF_F_HW_TC bit in net device's feature set to enable offload TC
infrastructure for port representor.
Implement TC filters replay function required to restore filters settings
while switchdev configuration is rebuilt.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.
To accomplish this driver, has to set correct Tx descriptor. When
packet is sent from representor to VF, destination should be
set to VF VSI. When packet is sent from uplink port destination
should be uplink to bypass switch infrastructure and send packet
outside.
On Rx site driver should check source VSI field from Rx descriptor
and based on that forward packed to correct netdev. To allow
this there is a target netdevs table in control plane VSI
struct.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Only way to enable switchdev is to create VFs when the eswitch
mode is set to switchdev. Check if correct mode is set and
enable switchdev in function which creating VFs.
Disable switchdev when user change number of VFs to 0. Changing
eswitch mode back to legacy when VFs are created in switchdev
mode isn't allowed.
As switchdev takes care of managing filter rules, adding new
rules on VF is blocked.
In case of resetting VF driver has to update pointer in ice_repr
struct, because after reset VSI related things can change.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
New type of VSI has to be defined for switchdev control plane
VSI. Number of allocated Tx and Rx queue has to be equal to
amount of VFs, because each port representor should have one
Tx and Rx queue.
Also to not increase number of used irqs too much, control plane
VSI uses only one q_vector and handle all queues in one irq.
To allow handling all queues in one irq , new function to clean
msix for eswitch was introduced. This function will schedule napi
for each representor instead of scheduling it only for one like in
normal clean irq function.
Only one additional msix has to be requested. Always try to request
it in ice_ena_msix_range function.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.
Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.
On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.
As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.
To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.
Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Write set and get eswitch mode functions used by devlink
ops. Use new pf struct member eswitch_mode to track current
eswitch mode in driver.
Changing eswitch mode is only allowed when there are no
VFs created.
Create new file for eswitch related code.
Add config flag ICE_SWITCHDEV to allow user to choose if
switchdev support should be enabled or disabled.
Use case examples:
- show current eswitch mode ('legacy' is the default one)
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
- move to 'switchdev' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode
switchdev
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode switchdev
- create 2 VFs
[root@localhost]# echo 2 > /sys/class/net/ens4f1/device/sriov_numvfs
- unsuccessful attempt to change eswitch mode while VFs are created
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
devlink answers: Operation not supported
- destroy VFs
[root@localhost]# echo 0 > /sys/class/net/ens4f1/device/sriov_numvfs
- restore 'legacy' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
