| Age | Commit message (Collapse) | Author |
|---|
|
This change adds support for changing MTU on port representor in
switchdev mode, by setting the min/max MTU values on port representor
netdev. Before it was possible to change the MTU only in a limited,
default range (68-1500).
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add tc-flower support for VF port representor devices.
Implement ndo_setup_tc callback for TC HW offload on VF port representors
devices. Implemented both methods: add and delete tc-flower flows.
Mark NETIF_F_HW_TC bit in net device's feature set to enable offload TC
infrastructure for port representor.
Implement TC filters replay function required to restore filters settings
while switchdev configuration is rebuilt.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce the following ethtool operations for VF's representor:
-get_drvinfo
-get_strings
-get_ethtool_stats
-get_sset_count
-get_link
In all cases, existing operations were used with minor
changes which allow us to detect if ethtool op was called for
representor. Only VF VSI stats will be available for representor.
Implement ndo_get_stats64 for port representor. This will update
VF VSI stats and read them.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.
To accomplish this driver, has to set correct Tx descriptor. When
packet is sent from representor to VF, destination should be
set to VF VSI. When packet is sent from uplink port destination
should be uplink to bypass switch infrastructure and send packet
outside.
On Rx site driver should check source VSI field from Rx descriptor
and based on that forward packed to correct netdev. To allow
this there is a target netdevs table in control plane VSI
struct.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.
Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.
On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.
As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.
To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.
Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev driver shouldn't add MAC, VLAN and promisc
filters on iavf demand but should return success to not
break normal iavf flow.
Achieve that by creating table of functions pointer with
default functions used to parse iavf command. While parse
iavf command, call correct function from table instead of
calling function direct.
When port representors are being created change functions
in table to new one that behaves correctly for switchdev
puprose (ignoring new filters).
Change back to default ops when representors are being
removed.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Port representor is used to manage VF from host side. To allow
it each created representor registers netdevice with random hw
address. Also devlink port is created for all representors.
Port representor name is created based on switch id or managed
by devlink core if devlink port was registered with success.
Open and stop ndo ops are implemented to allow managing the VF
link state. Link state is tracked in VF struct.
Struct ice_netdev_priv is extended by pointer to representor
field. This is needed to get correct representor from netdev
struct mostly used in ndo calls.
Implement helper functions to check if given netdev is netdev of
port representor (ice_is_port_repr_netdev) and to get representor
from netdev (ice_netdev_to_repr).
As driver mostly will create or destroy port representors on all
VFs instead of on single one, write functions to add and remove
representor for each VF.
Representor struct contains pointer to source VSI, which is VSI
configured on VF, backpointer to VF, backpointer to netdev,
q_vector pointer and metadata_dst which will be used in data path.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
