| Age | Commit message (Collapse) | Author |
|---|
|
The other interrupt cause register (OICR), global interrupt 0, is
disabled when enabling VFs to prevent handling VFLR. If the OICR is
not rearmed then the VF cannot communicate with the PF.
Rearm the OICR after enabling VFs.
Fixes: 916c7fdf5e93 ("ice: Separate VF VSI initialization/creation from reset flow")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When VF is being reset, ice_reset_vf() will be called and FDIR
resource should be released and initialized again.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d64e ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a VF is removed and/or reset its Tx queues need to be
stopped from the PF. This is done by calling the ice_dis_vf_qs()
function, which calls ice_vsi_stop_lan_tx_rings(). Currently
ice_dis_vf_qs() is protected by the VF state bit ICE_VF_STATE_QS_ENA.
Unfortunately, this is causing the Tx queues to not be disabled in some
cases and when the VF tries to re-enable/reconfigure its Tx queues over
virtchnl the op is failing. This is because a VF can be reset and/or
removed before the ICE_VF_STATE_QS_ENA bit is set, but the Tx queues
were already configured via ice_vsi_cfg_single_txq() in the
VIRTCHNL_OP_CONFIG_VSI_QUEUES op. However, the ICE_VF_STATE_QS_ENA bit
is set on a successful VIRTCHNL_OP_ENABLE_QUEUES, which will always
happen after the VIRTCHNL_OP_CONFIG_VSI_QUEUES op.
This was causing the following error message when loading the ice
driver, creating VFs, and modifying VF trust in an endless loop:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by always calling ice_dis_vf_qs() and silencing the error
message in ice_vsi_stop_tx_ring() since the calling code ignores the
return anyway. Also, all other places that call ice_vsi_stop_tx_ring()
catch the error, so this doesn't affect those flows since there was no
change to the values the function returns.
Other solutions were considered (i.e. tracking which VF queues had been
"started/configured" in VIRTCHNL_OP_CONFIG_VSI_QUEUES, but it seemed
more complicated than it was worth. This solution also brings in the
chance for other unexpected conditions due to invalid state bit checks.
So, the proposed solution seemed like the best option since there is no
harm in failing to stop Tx queues that were never started.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
VF was not able to change its hardware MAC address in case
the new address was already present in the MAC filter list.
Change the handling of VF add mac request to not return
if requested MAC address is already present on the list
and check if its hardware MAC needs to be updated in this case.
Fixes: ed4c068d46f6 ("ice: Enable ip link show on the PF to display VF unicast MAC(s)")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently when a trusted VF enables promiscuous mode spoofchk will be
disabled. This is wrong and should only be modified from the
ndo_set_vf_spoofchk callback. Fix this by removing the call to toggle
spoofchk for trusted VFs.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a VF requests promiscuous mode and it's trusted and true promiscuous
mode is enabled the PF driver attempts to enable unicast and/or
multicast promiscuous mode filters based on the request. This is fine,
but there are a couple issues with the current code.
[1] The define to configure the unicast promiscuous mode mask also
includes bits to configure the multicast promiscuous mode mask, which
causes multicast to be set/cleared unintentionally.
[2] All 4 cases for enable/disable unicast/multicast mode are not
handled in the promiscuous mode message handler, which causes
unexpected results regarding the current promiscuous mode settings.
To fix [1] make sure any promiscuous mask defines include the correct
bits for each of the promiscuous modes.
To fix [2] make sure that all 4 cases are handled since there are 2 bits
(FLAG_VF_UNICAST_PROMISC and FLAG_VF_MULTICAST_PROMISC) that can be
either set or cleared. Also, since either unicast and/or multicast
promiscuous configuration can fail, introduce two separate error values
to handle each of these cases.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, the vlan_promisc flag is used exclusively by VF VSI to
determine whether or not to toggle VLAN pruning along with
trusted/true-promiscuous mode. This is not needed for a couple of
reasons. First, trusted/true-promiscuous mode is only supposed to allow
all MAC filters within VLANs that a VF has added filters for, so VLAN
pruning should not be disabled. Second, the boolean argument makes the
function confusing and unintuitive. Remove this flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Part of virtchannel messages are treated in different way in switchdev
mode to block configuring VFs from iavf driver side. This blocking was
done by doing nothing and returning success, event without sending
response.
Not sending response for opcodes that aren't supported in switchdev mode
leads to block iavf driver message handling. This happens for example
when vlan is configured at VF config time (VLAN module is already
loaded).
To get rid of it ice driver should answer for each VF message. In
switchdev mode:
- for adding/deleting VLAN driver should answer success without doing
anything to allow creating vlan device on VFs
- for enabling/disabling VLAN stripping and promiscuous mode driver
should answer not supported, this feature in switchdev can be only
set from host side
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Return the error code if ice_eswitch_configure() fails. Don't return
success.
Fixes: 1c54c839935b ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Merge issues caused the check for switchdev mode has been inserted
in wrong place. It should be in ice_set_vf_trust not in ice_set_vf_mac.
Trusted VFs are forbidden in switchdev mode because they should
be configured only from the host side.
Fixes: 1c54c839935b ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce the following ethtool operations for VF's representor:
-get_drvinfo
-get_strings
-get_ethtool_stats
-get_sset_count
-get_link
In all cases, existing operations were used with minor
changes which allow us to detect if ethtool op was called for
representor. Only VF VSI stats will be available for representor.
Implement ndo_get_stats64 for port representor. This will update
VF VSI stats and read them.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Only way to enable switchdev is to create VFs when the eswitch
mode is set to switchdev. Check if correct mode is set and
enable switchdev in function which creating VFs.
Disable switchdev when user change number of VFs to 0. Changing
eswitch mode back to legacy when VFs are created in switchdev
mode isn't allowed.
As switchdev takes care of managing filter rules, adding new
rules on VF is blocked.
In case of resetting VF driver has to update pointer in ice_repr
struct, because after reset VSI related things can change.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev driver shouldn't add MAC, VLAN and promisc
filters on iavf demand but should return success to not
break normal iavf flow.
Achieve that by creating table of functions pointer with
default functions used to parse iavf command. While parse
iavf command, call correct function from table instead of
calling function direct.
When port representors are being created change functions
in table to new one that behaves correctly for switchdev
puprose (ignoring new filters).
Change back to default ops when representors are being
removed.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Port representor is used to manage VF from host side. To allow
it each created representor registers netdevice with random hw
address. Also devlink port is created for all representors.
Port representor name is created based on switch id or managed
by devlink core if devlink port was registered with success.
Open and stop ndo ops are implemented to allow managing the VF
link state. Link state is tracked in VF struct.
Struct ice_netdev_priv is extended by pointer to representor
field. This is needed to get correct representor from netdev
struct mostly used in ndo calls.
Implement helper functions to check if given netdev is netdev of
port representor (ice_is_port_repr_netdev) and to get representor
from netdev (ice_netdev_to_repr).
As driver mostly will create or destroy port representors on all
VFs instead of on single one, write functions to add and remove
representor for each VF.
Representor struct contains pointer to source VSI, which is VSI
configured on VF, backpointer to VF, backpointer to netdev,
q_vector pointer and metadata_dst which will be used in data path.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.
By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When VFs are setup and torn down in quick succession, it is possible
that a VF is torn down by the PF while the VF's virtchnl requests are
still in the PF's mailbox ring. Processing the VF's virtchnl request
when the VF itself doesn't exist results in undefined behavior. Fix
this by adding a check to stop processing virtchnl requests when VF
teardown is in progress.
Fixes: ddf30f7ff840 ("ice: Add handler to configure SR-IOV")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_get_vf_vsi() is being called twice for the same VSI. Remove the
unnecessary call/assignment.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-07
This series contains updates to virtchnl header file and ice driver.
Brett adds capability bits to virtchnl to specify whether a primary or
secondary MAC address is being requested and adds the implementation to
ice. He also adds storing of VF MAC address so that it will be preserved
across reboots of VM and refactors VF queue configuration to remove the
expectation that configuration be done all at once.
Krzysztof refactors ice_setup_rx_ctx() to remove configuration not
related to Rx context into a new function, ice_vsi_cfg_rxq().
Liwei Song extends the wait time for the global config timeout.
Salil Mehta refactors code in ice_vsi_set_num_qs() to remove an
unnecessary call when the user has requested specific number of Rx or Tx
queues.
Jesse converts define macros to static inlines for NOP configurations.
Jake adds messaging when devlink fails to read device capabilities and
when pldmfw cannot find the requested firmware. Adds a wait for reset
completion when reporting devlink info and reinitializes NVM during
rebuild to ensure values are current.
Ani adds detection and reporting of modules exceeding supported power
levels and changes an error message to a debug message.
Paul fixes a clang warning for deadcode.DeadStores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a VF requests queue configuration via
VIRTCHNL_OP_CONFIG_VSI_QUEUES the PF driver expects that this message
will only be called once and we always assume the queues being
configured start from 0. This is incorrect and is causing issues when
a VF tries to send this message for multiple queue blocks. Fix this by
using the queue_id specified in the virtchnl message and allowing for
individual Rx and/or Tx queues to be configured.
Also, reduce the duplicated for loops for configuring the queues by
moving all the logic into a single for loop.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If a VM reboots and/or VF driver is unloaded, its cached hardware MAC
address (hw_lan_addr.addr) is cleared in some cases. If the VF is
trusted, then the PF driver allows the VF to clear its old MAC address
even if this MAC was configured by a host administrator. If the VF is
untrusted, then the PF driver allows the VF to clear its old MAC
address only if the host admin did not set it.
For the trusted VF case, this is unexpected and will cause issues
because the host configured MAC (i.e. via XML) will be cleared on VM
reboot. For the untrusted VF case, this is done to be consistent and it
will allow the VF to keep the same MAC across VM reboot.
Fix this by introducing dev_lan_addr to the VF structure. This will be
the VF's MAC address when it's up and running and in most cases will be
the same as the hw_lan_addr. However, to address the VM reboot and
unload/reload problem, the driver will never allow the hw_lan_addr to be
cleared via VIRTCHNL_OP_DEL_ETH_ADDR. When the VF's MAC is changed, the
dev_lan_addr and hw_lan_addr will always be updated with the same value.
The only ways the VF's MAC can change are the following:
- Set the VF's MAC administratively on the host via iproute2.
- If the VF is trusted and changes/sets its own MAC.
- If the VF is untrusted and the host has not set the MAC via iproute2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently there is no way for a VF driver to specify if it wants to
change it's hardware address. New bits are being added to virtchnl.h
in struct virtchnl_ether_addr that allow for the VF to correctly
communicate this information. However, legacy VF drivers that don't
support the new virtchnl.h bits still need to be supported. Make a
best effort attempt at saving the VF's primary/device address in the
legacy case and depend on the VIRTCHNL_ETHER_ADDR_PRIMARY type for
the new case.
Legacy case - If a unicast MAC is being added and the
hw_lan_addr.addr is empty, then populate it. This assumes that the
address is the VF's hardware address. If a unicast MAC is being
added and the hw_lan_addr.addr is not empty, then cache it in the
legacy_last_added_umac.addr. If a unicast MAC is being deleted and it
matches the hw_lan_addr.addr, then zero the hw_lan_addr.addr.
Also, if the legacy_last_added_umac.addr has not expired, copy the
legacy_last_added_umac.addr into the hw_lan_addr.addr. This is done
because we cannot guarantee the order of VIRTCHNL_OP_ADD_ETH_ADDR and
VIRTCHNL_OP_DEL_ETH_ADDR.
New case - If a unicast MAC is being added and it's specified as
VIRTCHNL_ETHER_ADDR_PRIMARY, then replace the current
hw_lan_addr.addr. If a unicast MAC is being deleted and it's type
is specified as VIRTCHNL_ETHER_ADDR_PRIMARY, then zero the
hw_lan_addr.addr.
Untrusted VFs - Only allow above legacy/new changes to their
hardware address if the PF has not set it administratively via
iproute2.
Trusted VFs - Always allow above legacy/new changes to their
hardware address even if the PF has administratively set it via
iproute2.
Also, change the variable dflt_lan_addr to hw_lan_addr to clearly
represent the purpose of this variable since it's purpose is to
act as a hardware programmed MAC address for the VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
VSI rebuild can be failed for LAN queue config, then the VF's VSI will
be NULL, the VF reset should be stopped with the VF entering into the
disable state.
Fixes: 12bb018c538c ("ice: Refactor VF reset")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Some AVF drivers expect the VF_MBX_ATQLEN register to be cleared for any
type of VFR/VFLR. Fix this by clearing the VF_MBX_ATQLEN register at the
same time as VF_MBX_ARQLEN.
Fixes: 82ba01282cf8 ("ice: clear VF ARQLEN register on reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the handler for virtchnl message VIRTCHNL_OP_DEL_RSS_CFG to remove
an existing RSS configuration with matching hashed fields.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Co-developed-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, RSS hash input is not available to AVF by ethtool, it is set
by the PF directly.
Add the RSS configure support for AVF through new virtchnl message, and
define the capability flag VIRTCHNL_VF_OFFLOAD_ADV_RSS_PF to query this
new RSS offload support.
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, the driver gets the VF's VSI by using a long string of
dereferences (i.e. vf->pf->vsi[vf->lan_vsi_idx]). If the method to get
the VF's VSI were to change the driver would have to change it in every
location. Fix this by adding the helper ice_get_vf_vsi().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pointer vsi is being re-assigned a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As the hardware is capable of supporting UDP segmentation offload, add a
capability bit to virtchnl.h to communicate this and have the driver
advertise its support.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Declare bitmap of allowed commands on VF. Initialize default
opcodes list that should be always supported. Declare array of
supported opcodes for each caps used in virtchnl code.
Change allowed bitmap by setting or clearing corresponding
bit to allowlist (bit set) or denylist (bit clear).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Correct reported warnings for "warning: expecting prototype for ...
Prototype was for ... instead"
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
|
|
The virtual channel is going to be extended to support FDIR and
RSS configure from AVF. New data structures and OP codes will be
added, the patch enable the FDIR part.
To support above advanced AVF feature, we need to figure out
what kind of data structure should be passed from VF to PF to describe
an FDIR rule or RSS config rule. The common part of the requirement is
we need a data structure to represent the input set selection of a rule's
hash key.
An input set selection is a group of fields be selected from one or more
network protocol layers that could be identified as a specific flow.
For example, select dst IP address from an IPv4 header combined with
dst port from the TCP header as the input set for an IPv4/TCP flow.
The patch adds a new data structure virtchnl_proto_hdrs to abstract
a network protocol headers group which is composed of layers of network
protocol header(virtchnl_proto_hdr).
A protocol header contains a 32 bits mask (field_selector) to describe
which fields are selected as input sets, as well as a header type
(enum virtchnl_proto_hdr_type). Each bit is mapped to a field in
enum virtchnl_proto_hdr_field guided by its header type.
+------------+-----------+------------------------------+
| | Proto Hdr | Header Type A |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
|Proto Hdrs | Proto Hdr | Header Type B |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | Proto Hdr | Header Type C |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | .... |
+-------------------------------------------------------+
All fields in enum virtchnl_proto_hdr_fields are grouped with header type
and the value of the first field of a header type is always 32 aligned.
enum proto_hdr_type {
header_type_A = 0;
header_type_B = 1;
....
}
enum proto_hdr_field {
/* header type A */
header_A_field_0 = 0,
header_A_field_1 = 1,
header_A_field_2 = 2,
header_A_field_3 = 3,
/* header type B */
header_B_field_0 = 32, // = header_type_B << 5
header_B_field_0 = 33,
header_B_field_0 = 34
header_B_field_0 = 35,
....
};
So we have:
proto_hdr_type = proto_hdr_field / 32
bit offset = proto_hdr_field % 32
To simply the protocol header's operations, couple help macros are added.
For example, to select src IP and dst port as input set for an IPv4/UDP
flow.
we have:
struct virtchnl_proto_hdr hdr[2];
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[0], IPV4)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[0], IPV4, SRC)
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[1], UDP)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[1], UDP, DST)
The byte array is used to store the protocol header of a training package.
The byte array must be network order.
The patch added virtual channel support for iAVF FDIR add/validate/delete
filter. iAVF FDIR is Flow Director for Intel Adaptive Virtual Function
which can direct Ethernet packets to the queues of the Network Interface
Card. Add/delete command is adding or deleting one rule for each virtual
channel message, while validate command is just verifying if this rule
is valid without any other operations.
To add or delete one rule, driver needs to config TCAM and Profile,
build training packets which contains the input set value, and send
the training packets through FDIR Tx queue. In addition, driver needs to
manage the software context to avoid adding duplicated rules, deleting
non-existent rule, input set conflicts and other invalid cases.
NOTE:
Supported pattern/actions and their parse functions are not be included in
this patch, they will be added in a separate one.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Simei Su <simei.su@intel.com>
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently if an AVF driver doesn't account for the possibility of a
port VLAN when determining its max packet size then packets at MTU will
be dropped. It is not the VF driver's responsibility to account for a
port VLAN so fix this. To fix this, do the following:
1. Add a function that determines the max packet size a VF is allowed by
using the port's max packet size and whether the VF is in a port
VLAN. If a port VLAN is configured then a VF's max packet size will
always be the port's max packet size minus VLAN_HLEN. Otherwise it
will be the port's max packet size.
2. Use this function to verify the max packet size from the VF.
3. If there is a port VLAN configured then add 4 bytes (VLAN_HLEN) to
the VF's max packet size configuration.
Also, the VIRTCHNL_OP_GET_VF_RESOURCES message provides the capability
to communicate a VF's max packet size. Use the new function for this
purpose.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the PF will only set a trusted VF as the default VSI when it
requests FLAG_VF_UNICAST_PROMISC over VIRTCHNL. However, when
FLAG_VF_MULTICAST_PROMISC is set it's expected that the trusted VF will
see multicast packets that don't have a matching destination MAC in the
devices internal switch. Fix this by setting the trusted VF as the
default VSI if either FLAG_VF_UNICAST_PROMISC or
FLAG_VF_MULTICAST_PROMISC is set.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the framework and initial implementation for receiving and processing
netdev bonding events. This is only the software support and the
implementation of the HW offload for bonding support will be coming at a
later time. There are some architectural gaps that need to be closed
before that happens.
Because this is a software only solution that supports in kernel bonding,
SR-IOV is not supported with this implementation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently there is no message printed on the host when a VF goes in and
out of promiscuous mode. This is causing confusion because this is the
expected behavior based on i40e. Fix this.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a collection of minor fixes including typos, white space, and
style. No functional changes.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
Currently VFs are only allowed to get 16, 4, and 1 queue pair by
default, which require 17, 5, and 2 MSI-X vectors respectively. This
is because each VF needs a MSI-X per data queue and a MSI-X for its
other interrupt. The calculation is based on the number of VFs created,
MSI-X available, and queue pairs available at the time of VF creation.
Unfortunately the values above exclude 2 queue pairs when only 3 MSI-X
are available to each VF based on resource constraints. The current
calculation would default to 2 MSI-X and 1 queue pair. This is a waste
of resources, so fix this by allowing 2 queue pairs per VF when there
are between 2 and 5 MSI-X available per VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
