| Age | Commit message (Collapse) | Author |
|---|
|
The ice_virtchnl_pf.c and ice_virtchnl_pf.h files are where most of the
code for implementing Single Root IOV virtualization resides. This code
includes support for bringing up and tearing down VFs, hooks into the
kernel SR-IOV netdev operations, and for handling virtchnl messages from
VFs.
In the future, we plan to support Scalable IOV in addition to Single
Root IOV as an alternative virtualization scheme. This implementation
will re-use some but not all of the code in ice_virtchnl_pf.c
To prepare for this future, we want to refactor and split up the code in
ice_virtchnl_pf.c into the following scheme:
* ice_vf_lib.[ch]
Basic VF structures and accessors. This is where scheme-independent
code will reside.
* ice_virtchnl.[ch]
Virtchnl message handling. This is where the bulk of the logic for
processing messages from VFs using the virtchnl messaging scheme will
reside. This is separated from ice_vf_lib.c because it is distinct
and has a bulk of the processing code.
* ice_sriov.[ch]
Single Root IOV implementation, including initialization and the
routines for interacting with SR-IOV based netdev operations.
* (future) ice_siov.[ch]
Scalable IOV implementation.
As a first step, lets assume that all of the code in
ice_virtchnl_pf.[ch] is for Single Root IOV. Rename this file to
ice_sriov.c and its header to ice_sriov.h
Future changes will further split out the code in these files following
the plan outlined here.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
net/dsa/dsa2.c
commit afb3cc1a397d ("net: dsa: unlock the rtnl_mutex when dsa_master_setup() fails")
commit e83d56537859 ("net: dsa: replay master state events in dsa_tree_{setup,teardown}_master")
https://lore.kernel.org/all/20220307101436.7ae87da0@canb.auug.org.au/
drivers/net/ethernet/intel/ice/ice.h
commit 97b0129146b1 ("ice: Fix error with handling of bonding MTU")
commit 43113ff73453 ("ice: add TTY for GNSS module for E810T device")
https://lore.kernel.org/all/20220310112843.3233bcf1@canb.auug.org.au/
drivers/staging/gdm724x/gdm_lte.c
commit fc7f750dc9d1 ("staging: gdm724x: fix use after free in gdm_lte_rx()")
commit 4bcc4249b4cf ("staging: Use netif_rx().")
https://lore.kernel.org/all/20220308111043.1018a59d@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a28 ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6bf5 ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9c1
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver stores VF structures in a simple array which is allocated
once at the time of VF creation. The VF structures are then accessed
from the array by their VF ID. The ID must be between 0 and the number
of allocated VFs.
Multiple threads can access this table:
* .ndo operations such as .ndo_get_vf_cfg or .ndo_set_vf_trust
* interrupts, such as due to messages from the VF using the virtchnl
communication
* processing such as device reset
* commands to add or remove VFs
The current implementation does not keep track of when all threads are
done operating on a VF and can potentially result in use-after-free
issues caused by one thread accessing a VF structure after it has been
released when removing VFs. Some of these are prevented with various
state flags and checks.
In addition, this structure is quite static and does not support a
planned future where virtualization can be more dynamic. As we begin to
look at supporting Scalable IOV with the ice driver (as opposed to just
supporting Single Root IOV), this structure is not sufficient.
In the future, VFs will be able to be added and removed individually and
dynamically.
To allow for this, and to better protect against a whole class of
use-after-free bugs, replace the VF storage with a combination of a hash
table and krefs to reference track all of the accesses to VFs through
the hash table.
A hash table still allows efficient look up of the VF given its ID, but
also allows adding and removing VFs. It does not require contiguous VF
IDs.
The use of krefs allows the cleanup of the VF memory to be delayed until
after all threads have released their reference (by calling ice_put_vf).
To prevent corruption of the hash table, a combination of RCU and the
mutex table_lock are used. Addition and removal from the hash table use
the RCU-aware hash macros. This allows simple read-only look ups that
iterate to locate a single VF can be fast using RCU. Accesses which
modify the hash table, or which can't take RCU because they sleep, will
hold the mutex lock.
By using this design, we have a stronger guarantee that the VF structure
can't be released until after all threads are finished operating on it.
We also pave the way for the more dynamic Scalable IOV implementation in
the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Before we switch the VF data structure storage mechanism to a hash,
introduce new accessor functions to define the new interface.
* ice_get_vf_by_id is a function used to obtain a reference to a VF from
the table based on its VF ID
* ice_has_vfs is used to quickly check if any VFs are configured
* ice_get_num_vfs is used to get an exact count of how many VFs are
configured
We can drop the old ice_validate_vf_id function, since every caller was
just going to immediately access the VF table to get a reference
anyways. This way we simply use the single ice_get_vf_by_id to both
validate the VF ID is within range and that there exists a VF with that
ID.
This change enables us to more easily convert the codebase to the hash
table since most callers now properly use the interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We maintain a number of values for VFs within the ice_pf structure. This
includes the VF table, the number of allocated VFs, the maximum number
of supported SR-IOV VFs, the number of queue pairs per VF, the number of
MSI-X vectors per VF, and a bitmap of the VFs with detected MDD events.
We're about to add a few more variables to this list. Clean this up
first by extracting these members out into a new ice_vfs structure
defined in ice_virtchnl_pf.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_for_each_vf macro is intended to be used to loop over all VFs.
The current implementation relies on an iterator that is the index into
the VF array in the PF structure. This forces all users to perform a
look up themselves.
This abstraction forces a lot of duplicate work on callers and leaks the
interface implementation to the caller. Replace this with an
implementation that includes the VF pointer the primary iterator. This
version simplifies callers which just want to iterate over every VF, as
they no longer need to perform their own lookup.
The "i" iterator value is replaced with a new unsigned int "bkt"
parameter, as this will match the necessary interface for replacing
the VF array with a hash table. For now, the bkt is the VF ID, but in
the future it will simply be the hash bucket index. Document that it
should not be treated as a VF ID.
This change aims to simplify switching from the array to a hash table. I
considered alternative implementations such as an xarray but decided
that the hash table was the simplest and most suitable implementation. I
also looked at methods to hide the bkt iterator entirely, but I couldn't
come up with a feasible solution that worked for hash table iterators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When removing VFs, the driver takes a weird approach of assigning
pf->num_alloc_vfs to 0 before iterating over the VFs using a temporary
variable.
This logic has been in the driver for a long time, and seems to have
been carried forward from i40e.
We want to refactor the way VFs are stored, and iterating over the data
structure without the ice_for_each_vf interface impedes this work.
The logic relies on implicitly using the num_alloc_vfs as a sort of
"safe guard" for accessing VF data.
While this sort of guard makes sense for Single Root IOV where all VFs
are added at once, the data structures don't work for VFs which can be
added and removed dynamically. We also have a separate state flag,
ICE_VF_DEINIT_IN_PROGRESS which is a stronger protection against
concurrent removal and access.
Avoid the custom tmp iteration and replace it with the standard
ice_for_each_vf iterator. Delay the assignment of num_alloc_vfs until
after this loop finishes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_send_msg_to_vf function is used by the PF to send a response
to a VF. This function has overzealous checks to ensure its not passed a
NULL VF pointer and to ensure that the passed in struct ice_vf has a
valid vf_id sub-member.
These checks have existed since commit 1071a8358a28 ("ice: Implement
virtchnl commands for AVF support") and function as simple sanity
checks.
We are planning to refactor the ice driver to use a hash table along
with appropriate locks in a future refactor. This change will modify how
the ice_validate_vf_id function works. Instead of a simple >= check to
ensure the VF ID is between some range, it will check the hash table to
see if the specified VF ID is actually in the table. This requires that
the function properly lock the table to prevent race conditions.
The checks may seem ok at first glance, but they don't really provide
much benefit.
In order for ice_vc_send_msg_to_vf to have these checks fail, the
callers must either (1) pass NULL as the VF, (2) construct an invalid VF
pointer manually, or (3) be using a VF pointer which becomes invalid
after they obtain it properly using ice_get_vf_by_id.
For (1), a cursory glance over callers of ice_vc_send_msg_to_vf can show
that in most cases the functions already operate assuming their VF
pointer is valid, such as by derferencing vf->pf or other members.
They obtain the VF pointer by accessing the VF array using the VF ID,
which can never produce a NULL value (since its a simple address
operation on the array it will not be NULL.
The sole exception for (1) is that ice_vc_process_vf_msg will forward a
NULL VF pointer to this function as part of its goto error handler
logic. This requires some minor cleanup to simply exit immediately when
an invalid VF ID is detected (Rather than use the same error flow as
the rest of the function).
For (2), it is unexpected for a flow to construct a VF pointer manually
instead of accessing the VF array. Defending against this is likely to
just hide bad programming.
For (3), it is definitely true that VF pointers could become invalid,
for example if a thread is processing a VF message while the VF gets
removed. However, the correct solution is not to add additional checks
like this which do not guarantee to prevent the race. Instead we plan to
solve the root of the problem by preventing the possibility entirely.
This solution will require the change to a hash table with proper
locking and reference counts of the VF structures. When this is done,
ice_validate_vf_id will require locking of the hash table. This will be
problematic because all of the callers of ice_vc_send_msg_to_vf will
already have to take the lock to obtain the VF pointer anyways. With a
mutex, this leads to a double lock that could hang the kernel thread.
Avoid this by removing the checks which don't provide much value, so
that we can safely add the necessary protections properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After removing all VFs, the driver clears the VFLR indication for VFs.
This has been in ice since the beginning of SR-IOV support in the ice
driver.
The implementation was copied from i40e, and the motivation for the VFLR
indication clearing is described in the commit f7414531a0cf ("i40e:
acknowledge VFLR when disabling SR-IOV")
The commit explains that we need to clear the VFLR indication because
the virtual function undergoes a VFLR event. If we don't indicate that
it is complete it can cause an issue when VFs are re-enabled due to
a "phantom" VFLR.
The register block read was added under a pci_vfs_assigned check
originally. This was done because we added the check after calling
pci_disable_sriov. This was later moved to disable SRIOV earlier in the
flow so that the VF drivers could be torn down before we removed
functionality.
Move the VFLR acknowledge into the main loop that tears down VF
resources. This avoids using the tmp value for iterating over VFs
multiple times. The result will make it easier to refactor the VF array
in a future change.
It's possible we might want to modify this flow to also stop checking
pci_vfs_assigned. However, it seems reasonable to keep this change: we
should only clear the VFLR if we actually disabled SR-IOV.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_mbx_clear_malvf function is used to clear the indication and
count of how many times a VF was detected as malicious. During
ice_free_vfs, we use this function to ensure that all removed VFs are
reset to a clean state.
The call currently is done at the end of ice_free_vfs() using a tmp
value to iterate over all of the entries in the bitmap.
This separate iteration using tmp is problematic for a planned refactor
of the VF array data structure. To avoid this, lets move the call
slightly higher into the function inside the loop where we teardown all
of the VFs. This avoids one use of the tmp value used for iteration.
We'll fix the other user in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We are planning to replace the simple array structure tracking VFs with
a hash table. This change will also remove the "num_alloc_vfs" variable.
Instead, new access functions to use the hash table as the source of
truth will be introduced. These will generally be equivalent to existing
checks, except during VF initialization.
Specifically, ice_set_per_vf_res() cannot use the hash table as it will
be operating prior to VF structures being inserted into the hash table.
Instead of using pf->num_alloc_vfs, simply pass the num_vfs value in
from the caller.
Note that a sub-function of ice_set_per_vf_res, ice_determine_res, also
implicitly depends on pf->num_alloc_vfs. Replace ice_determine_res with
a simpler inline implementation based on rounddown_pow_of_two. Note that
we must explicitly check that the argument is non-zero since it does not
play well with zero as a value.
Instead of using the function and while loop, simply calculate the
number of queues we have available by dividing by num_vfs. Check if the
desired queues are available. If not, round down to the nearest power of
2 that fits within our available queues.
This matches the behavior of ice_determine_res but is easier to follow
as simple in-line logic. Remove ice_determine_res entirely.
With this change, we no longer depend on the pf->num_alloc_vfs during
the initialization phase of VFs. This will allow us to safely remove it
in a future planned refactor of the VF data structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VSI structure contains a vf_id field used to associate a VSI with a
VF. This is used mainly for ICE_VSI_VF as well as partially for
ICE_VSI_CTRL associated with the VFs.
This API was designed with the idea that VFs are stored in a simple
array that was expected to be static throughout most of the driver's
life.
We plan on refactoring VF storage in a few key ways:
1) converting from a simple static array to a hash table
2) using krefs to track VF references obtained from the hash table
3) use RCU to delay release of VF memory until after all references
are dropped
This is motivated by the goal to ensure that the lifetime of VF
structures is accounted for, and prevent various use-after-free bugs.
With the existing vsi->vf_id, the reference tracking for VFs would
become somewhat convoluted, because each VSI maintains a vf_id field
which will then require performing a look up. This means all these flows
will require reference tracking and proper usage of rcu_read_lock, etc.
We know that the VF VSI will always be backed by a valid VF structure,
because the VSI is created during VF initialization and removed before
the VF is destroyed. Rely on this and store a reference to the VF in the
VSI structure instead of storing a VF ID. This will simplify the usage
and avoid the need to perform lookups on the hash table in the future.
For ICE_VSI_VF, it is expected that vsi->vf is always non-NULL after
ice_vsi_alloc succeeds. Because of this, use WARN_ON when checking if a
vsi->vf pointer is valid when dealing with VF VSIs. This will aid in
debugging code which violates this assumption and avoid more disastrous
panics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
tools/testing/selftests/net/mptcp/mptcp_join.sh
34aa6e3bccd8 ("selftests: mptcp: add ip mptcp wrappers")
857898eb4b28 ("selftests: mptcp: add missing join check")
6ef84b1517e0 ("selftests: mptcp: more robust signal race test")
https://lore.kernel.org/all/20220221131842.468893-1-broonie@kernel.org/
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/act.h
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/ct.c
fb7e76ea3f3b6 ("net/mlx5e: TC, Skip redundant ct clear actions")
c63741b426e11 ("net/mlx5e: Fix MPLSoUDP encap to use MPLS action information")
09bf97923224f ("net/mlx5e: TC, Move pedit_headers_action to parse_attr")
84ba8062e383 ("net/mlx5e: Test CT and SAMPLE on flow attr")
efe6f961cd2e ("net/mlx5e: CT, Don't set flow flag CT for ct clear flow")
3b49a7edec1d ("net/mlx5e: TC, Reject rules with multiple CT actions")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c503e63200c6 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200c6 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200c6 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
VFs by default are able to see all tagged traffic regardless of trust
and VLAN filters. Based on legacy devices (i.e. ixgbe, i40e), customers
expect VFs to receive all VLAN tagged traffic with a matching
destination MAC.
Add an ethtool private flag 'vf-vlan-pruning' and set the default to
off so VFs will receive all VLAN traffic directed towards them. When
the flag is turned on, VF will only be able to receive untagged
traffic or traffic with VLAN tags it has created interfaces for.
Also, the flag cannot be changed while any VFs are allocated. This was
done to simplify the implementation. So, if this flag is needed, then
the PF admin must enable it. If the user tries to enable the flag while
VFs are active, then print an unsupported message with the
vf-vlan-pruning flag included. In case multiple flags were specified, this
makes it clear to the user which flag failed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently there is only support for 802.1Q port VLANs on SR-IOV VFs. Add
support to also allow 802.1ad port VLANs when double VLAN mode is
enabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for the VF driver to be able to request
VIRTCHNL_VF_OFFLOAD_VLAN_V2, negotiate its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS, add/delete VLAN filters, and
enable/disable VLAN offloads.
VFs supporting VIRTCHNL_OFFLOAD_VLAN_V2 will be able to use the
following virtchnl opcodes:
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS
VIRTCHNL_OP_ADD_VLAN_V2
VIRTCHNL_OP_DEL_VLAN_V2
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING_V2
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING_V2
VIRTCHNL_OP_ENABLE_VLAN_INSERTION_V2
VIRTCHNL_OP_DISABLE_VLAN_INSERTION_V2
Legacy VF drivers may expect the initial VLAN stripping settings to be
configured by the PF, so the PF initializes VLAN stripping based on the
VIRTCHNL_OP_GET_VF_RESOURCES opcode. However, with VLAN support via
VIRTCHNL_VF_OFFLOAD_VLAN_V2, this function is only expected to be used
for VFs that only support VIRTCHNL_VF_OFFLOAD_VLAN, which will only
be supported when a port VLAN is configured. Update the function
based on the new expectations. Also, change the message when the PF
can't enable/disable VLAN stripping to a dev_dbg() as this isn't fatal.
When a VF isn't in a port VLAN and it only supports
VIRTCHNL_VF_OFFLOAD_VLAN when Double VLAN Mode (DVM) is enabled, then
the PF needs to reject the VIRTCHNL_VF_OFFLOAD_VLAN capability and
configure the VF in software only VLAN mode. To do this add the new
function ice_vf_vsi_cfg_legacy_vlan_mode(), which updates the VF's
inner and outer ice_vsi_vlan_ops functions and sets up software only
VLAN mode.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a new outer_vlan_ops member to the ice_vsi structure as outer VLAN
ops are only available when the device is in Double VLAN Mode (DVM).
Depending on the VSI type, the requirements for what operations to
use/allow differ.
By default all VSI's have unsupported inner and outer VSI VLAN ops. This
implementation was chosen to prevent unexpected crashes due to null
pointer dereferences. Instead, if a VSI calls an unsupported op, it will
just return -EOPNOTSUPP.
Add implementations to support modifying outer VLAN fields for VSI
context. This includes the ability to modify VLAN stripping, insertion,
and the port VLAN based on the outer VLAN handling fields of the VSI
context.
These functions should only ever be used if DVM is enabled because that
means the firmware supports the outer VLAN fields in the VSI context. If
the device is in DVM, then always use the outer_vlan_ops, else use the
vlan_ops since the device is in Single VLAN Mode (SVM).
Also, move adding the untagged VLAN 0 filter from ice_vsi_setup() to
ice_vsi_vlan_setup() as the latter function is specific to the PF and
all other VSI types that need an untagged VLAN 0 filter already do this
in their specific flows. Without this change, Flow Director is failing
to initialize because it does not implement any VSI VLAN ops.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current vf->port_vlan_info variable is a packed u16 that contains
the port VLAN ID and QoS/prio value. This is fine, but changes are
incoming that allow for an 802.1ad port VLAN. Add flexibility by
changing the vf->port_vlan_info member to be an ice_vlan structure.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Incoming changes to support 802.1Q and/or 802.1ad VLAN filtering and
offloads require more flexibility when configuring VLANs. The VSI VLAN
interface will allow flexibility for configuring VLANs for all VSI
types. Add new files to separate the VSI VLAN ops and move functions to
make the code more organized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There are multiple places where VLAN 0 is being added. Create a function
to be called in order to minimize changes as the implementation is expanded
to support double VLAN and avoid duplicated code.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add functions to configure Tx VLAN antispoof based on iproute
configuration and/or VLAN mode and VF driver support. This is needed
later so the driver can control when it can be configured. Also, add
functions that can be used to enable and disable MAC and VLAN
spoofcheck. Move spoofchk configuration during VSI setup into the
SR-IOV initialization path and into the post VSI rebuild flow for VF
VSIs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).
With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.
This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.
In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.
When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.
Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As all functions now return standard error codes, propagate the values
being returned instead of converting them to generic values.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
ice_status previously had a variable to contain these values where other
error codes had a variable as well. With ice_status now being an int,
there is no need for two variables to hold error values. In cases where
this occurs, remove one of the excess variables and use a single one.
Some initialization of variables are no longer needed and have been
removed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since the capability of a PTYPE within a specific package could be
negotiated by checking the HW bit map, it means that there's no need
to maintain a different PTYPE list for each type of the package when
parsing PTYPE. So refactor the PTYPE validating mechanism.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The other interrupt cause register (OICR), global interrupt 0, is
disabled when enabling VFs to prevent handling VFLR. If the OICR is
not rearmed then the VF cannot communicate with the PF.
Rearm the OICR after enabling VFs.
Fixes: 916c7fdf5e93 ("ice: Separate VF VSI initialization/creation from reset flow")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When VF is being reset, ice_reset_vf() will be called and FDIR
resource should be released and initialized again.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d64e ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a VF is removed and/or reset its Tx queues need to be
stopped from the PF. This is done by calling the ice_dis_vf_qs()
function, which calls ice_vsi_stop_lan_tx_rings(). Currently
ice_dis_vf_qs() is protected by the VF state bit ICE_VF_STATE_QS_ENA.
Unfortunately, this is causing the Tx queues to not be disabled in some
cases and when the VF tries to re-enable/reconfigure its Tx queues over
virtchnl the op is failing. This is because a VF can be reset and/or
removed before the ICE_VF_STATE_QS_ENA bit is set, but the Tx queues
were already configured via ice_vsi_cfg_single_txq() in the
VIRTCHNL_OP_CONFIG_VSI_QUEUES op. However, the ICE_VF_STATE_QS_ENA bit
is set on a successful VIRTCHNL_OP_ENABLE_QUEUES, which will always
happen after the VIRTCHNL_OP_CONFIG_VSI_QUEUES op.
This was causing the following error message when loading the ice
driver, creating VFs, and modifying VF trust in an endless loop:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by always calling ice_dis_vf_qs() and silencing the error
message in ice_vsi_stop_tx_ring() since the calling code ignores the
return anyway. Also, all other places that call ice_vsi_stop_tx_ring()
catch the error, so this doesn't affect those flows since there was no
change to the values the function returns.
Other solutions were considered (i.e. tracking which VF queues had been
"started/configured" in VIRTCHNL_OP_CONFIG_VSI_QUEUES, but it seemed
more complicated than it was worth. This solution also brings in the
chance for other unexpected conditions due to invalid state bit checks.
So, the proposed solution seemed like the best option since there is no
harm in failing to stop Tx queues that were never started.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
VF was not able to change its hardware MAC address in case
the new address was already present in the MAC filter list.
Change the handling of VF add mac request to not return
if requested MAC address is already present on the list
and check if its hardware MAC needs to be updated in this case.
Fixes: ed4c068d46f6 ("ice: Enable ip link show on the PF to display VF unicast MAC(s)")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently when a trusted VF enables promiscuous mode spoofchk will be
disabled. This is wrong and should only be modified from the
ndo_set_vf_spoofchk callback. Fix this by removing the call to toggle
spoofchk for trusted VFs.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a VF requests promiscuous mode and it's trusted and true promiscuous
mode is enabled the PF driver attempts to enable unicast and/or
multicast promiscuous mode filters based on the request. This is fine,
but there are a couple issues with the current code.
[1] The define to configure the unicast promiscuous mode mask also
includes bits to configure the multicast promiscuous mode mask, which
causes multicast to be set/cleared unintentionally.
[2] All 4 cases for enable/disable unicast/multicast mode are not
handled in the promiscuous mode message handler, which causes
unexpected results regarding the current promiscuous mode settings.
To fix [1] make sure any promiscuous mask defines include the correct
bits for each of the promiscuous modes.
To fix [2] make sure that all 4 cases are handled since there are 2 bits
(FLAG_VF_UNICAST_PROMISC and FLAG_VF_MULTICAST_PROMISC) that can be
either set or cleared. Also, since either unicast and/or multicast
promiscuous configuration can fail, introduce two separate error values
to handle each of these cases.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, the vlan_promisc flag is used exclusively by VF VSI to
determine whether or not to toggle VLAN pruning along with
trusted/true-promiscuous mode. This is not needed for a couple of
reasons. First, trusted/true-promiscuous mode is only supposed to allow
all MAC filters within VLANs that a VF has added filters for, so VLAN
pruning should not be disabled. Second, the boolean argument makes the
function confusing and unintuitive. Remove this flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Part of virtchannel messages are treated in different way in switchdev
mode to block configuring VFs from iavf driver side. This blocking was
done by doing nothing and returning success, event without sending
response.
Not sending response for opcodes that aren't supported in switchdev mode
leads to block iavf driver message handling. This happens for example
when vlan is configured at VF config time (VLAN module is already
loaded).
To get rid of it ice driver should answer for each VF message. In
switchdev mode:
- for adding/deleting VLAN driver should answer success without doing
anything to allow creating vlan device on VFs
- for enabling/disabling VLAN stripping and promiscuous mode driver
should answer not supported, this feature in switchdev can be only
set from host side
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Return the error code if ice_eswitch_configure() fails. Don't return
success.
Fixes: 1c54c839935b ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Merge issues caused the check for switchdev mode has been inserted
in wrong place. It should be in ice_set_vf_trust not in ice_set_vf_mac.
Trusted VFs are forbidden in switchdev mode because they should
be configured only from the host side.
Fixes: 1c54c839935b ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce the following ethtool operations for VF's representor:
-get_drvinfo
-get_strings
-get_ethtool_stats
-get_sset_count
-get_link
In all cases, existing operations were used with minor
changes which allow us to detect if ethtool op was called for
representor. Only VF VSI stats will be available for representor.
Implement ndo_get_stats64 for port representor. This will update
VF VSI stats and read them.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
