summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel
AgeCommit message (Collapse)Author
2024-04-12ice: Implement 'flow-type ether' rulesJakub Buchocki
Add support for 'flow-type ether' Flow Director rules via ethtool. Create packet segment info for filter configuration based on ethtool command parameters. Reuse infrastructure already created for ipv4 and ipv6 flows to convert packet segment into extraction sequence, which is later used to program the filter inside Flow Director block of the Rx pipeline. Rules not containing masks are processed by the Flow Director, and support the following set of input parameters in all combinations: src, dst, proto, vlan-etype, vlan, action. It is possible to specify address mask in ethtool parameters but only 00:00:00:00:00 and FF:FF:FF:FF:FF are valid. The same applies to proto, vlan-etype and vlan masks: only 0x0000 and 0xffff masks are valid. Testing: (DUT) iperf3 -s (DUT) ethtool -U ens785f0np0 flow-type ether dst <ens785f0np0 mac> \ action 10 (DUT) watch 'ethtool -S ens785f0np0 | grep rx_queue' (LP) iperf3 -c ${DUT_IP} Counters increase only for: 'rx_queue_10_packets' 'rx_queue_10_bytes' Signed-off-by: Jakub Buchocki <jakubx.buchocki@intel.com> Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com> Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Lukasz Plachno <lukasz.plachno@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-12ice: Remove unnecessary argument from ice_fdir_comp_rules()Lukasz Plachno
Passing v6 argument is unnecessary as flow_type is still analyzed inside the function. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Lukasz Plachno <lukasz.plachno@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-08igc: Remove redundant runtime resume for ethtool opsBjorn Helgaas
8c5ad0dae93c ("igc: Add ethtool support") added ethtool_ops.begin() and .complete(), which used pm_runtime_get_sync() to resume suspended devices before any ethtool_ops callback and allow suspend after it completed. Subsequently, f32a21376573 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops") added pm_runtime_get_sync() in the dev_ethtool() path, so the device is resumed before any ethtool_ops callback even if the driver didn't supply a .begin() callback. Remove the .begin() and .complete() callbacks, which are now redundant because dev_ethtool() already resumes the device. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-08igb: Remove redundant runtime resume for ethtool_opsBjorn Helgaas
749ab2cd1270 ("igb: add basic runtime PM support") added ethtool_ops.begin() and .complete(), which used pm_runtime_get_sync() to resume suspended devices before any ethtool_ops callback and allow suspend after it completed. Subsequently, f32a21376573 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops") added pm_runtime_get_sync() in the dev_ethtool() path, so the device is resumed before any ethtool_ops callback even if the driver didn't supply a .begin() callback. Remove the .begin() and .complete() callbacks, which are now redundant because dev_ethtool() already resumes the device. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-08e1000e: Remove redundant runtime resume for ethtool_opsBjorn Helgaas
e60b22c5b7e5 ("e1000e: fix accessing to suspended device") added ethtool_ops.begin() and .complete(), which used pm_runtime_get_sync() to resume suspended devices before any ethtool_ops callback and allow suspend after it completed. 3ef672ab1862 ("e1000e: ethtool unnecessarily takes device out of RPM suspend") removed ethtool_ops.begin() and .complete() and instead did pm_runtime_get_sync() only in the individual ethtool_ops callbacks that access device registers. Subsequently, f32a21376573 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops") added pm_runtime_get_sync() in the dev_ethtool() path, so the device is resumed before *any* ethtool_ops callback, as it was before 3ef672ab1862. Remove most runtime resumes from ethtool_ops, which are now redundant because the resume has already been done by dev_ethtool(). This is essentially a revert of 3ef672ab1862 ("e1000e: ethtool unnecessarily takes device out of RPM suspend"). There are a couple subtleties: - Prior to 3ef672ab1862, the device was resumed only for the duration of a single ethtool callback. 3ef672ab1862 changed e1000_set_phys_id() so the device was resumed for ETHTOOL_ID_ACTIVE and remained resumed until a subsequent callback for ETHTOOL_ID_INACTIVE. Preserve that part of 3ef672ab1862 so the device will not be runtime suspended while in the ETHTOOL_ID_ACTIVE state. - 3ef672ab1862 added "if (!pm_runtime_suspended())" in before reading the STATUS register in e1000_get_settings(). This was racy and is now unnecessary because dev_ethtool() has resumed the device already, so revert that. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-08net: handle HAS_IOPORT dependenciesNiklas Schnelle
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at compile time. We thus need to add HAS_IOPORT as dependency for those drivers requiring them. For the DEFXX driver the use of I/O ports is optional and we only need to fence specific code paths. It also turns out that with HAS_IOPORT handled explicitly HAMRADIO does not need the !S390 dependency and successfully builds the bpqether driver. Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Co-developed-by: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR. Conflicts: net/ipv4/ip_gre.c 17af420545a7 ("erspan: make sure erspan_base_hdr is present in skb->head") 5832c4a77d69 ("ip_tunnel: convert __be16 tunnel flags to bitmaps") https://lore.kernel.org/all/20240402103253.3b54a1cf@canb.auug.org.au/ Adjacent changes: net/ipv6/ip6_fib.c d21d40605bca ("ipv6: Fix infinite recursion in fib6_dump_done().") 5fc68320c1fb ("ipv6: remove RTNL protection from inet6_dump_fib()") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-03idpf: fix kernel panic on unknown packet typesJoshua Hay
In the very rare case where a packet type is unknown to the driver, idpf_rx_process_skb_fields would return early without calling eth_type_trans to set the skb protocol / the network layer handler. This is especially problematic if tcpdump is running when such a packet is received, i.e. it would cause a kernel panic. Instead, call eth_type_trans for every single packet, even when the packet type is unknown. Fixes: 3a8845af66ed ("idpf: add RX splitq napi poll support") Reported-by: Balazs Nemeth <bnemeth@redhat.com> Signed-off-by: Joshua Hay <joshua.a.hay@intel.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Salvatore Daniele <sdaniele@redhat.com> Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-03ice: fix enabling RX VLAN filteringPetr Oros
ice_port_vlan_on/off() was introduced in commit 2946204b3fa8 ("ice: implement bridge port vlan"). But ice_port_vlan_on() incorrectly assigns ena_rx_filtering to inner_vlan_ops in DVM mode. This causes an error when rx_filtering cannot be enabled in legacy mode. Reproducer: echo 1 > /sys/class/net/$PF/device/sriov_numvfs ip link set $PF vf 0 spoofchk off trust on vlan 3 dmesg: ice 0000:41:00.0: failed to enable Rx VLAN filtering for VF 0 VSI 9 during VF rebuild, error -95 Fixes: 2946204b3fa8 ("ice: implement bridge port vlan") Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-03ice: Fix freeing uninitialized pointersDan Carpenter
Automatically cleaned up pointers need to be initialized before exiting their scope. In this case, they need to be initialized to NULL before any return statement. Fixes: 90f821d72e11 ("ice: avoid unnecessary devm_ usage") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-02Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-04-01 (ice) This series contains updates to ice driver only. Michal Schmidt changes flow for gettimex64 to use host-side spinlock rather than hardware semaphore for lighter-weight locking. Steven adds ability for switch recipes to be re-used when firmware supports it. Thorsten Blum removes unwanted newlines in netlink messaging. Michal Swiatkowski and Piotr re-organize devlink related code; renaming, moving, and consolidating it to a single location. Michal also simplifies the devlink init and cleanup path to occur under a single lock call. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: hold devlink lock for whole init/cleanup ice: move devlink port code to a separate file ice: move ice_devlink.[ch] to devlink folder ice: Remove newlines in NL_SET_ERR_MSG_MOD ice: Add switch recipe reusing feature ice: fold ice_ptp_read_time into ice_ptp_gettimex64 ice: avoid the PTP hardware semaphore in gettimex64 path ice: add ice_adapter for shared data across PFs on the same NIC ==================== Link: https://lore.kernel.org/r/20240401172421.1401696-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-01Merge branch '1GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-03-29 (net: intel) This series contains updates to most Intel drivers. Jesse moves declaration of pci_driver struct to remove need for forward declarations in igb and converts Intel drivers to user newer power management ops. Sasha reworks power management flow on igc to avoid using rtnl_lock() during those flows. Maciej reorganizes i40e_nvm file to avoid forward declarations. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: i40e: avoid forward declarations in i40e_nvm.c igc: Refactor runtime power management flow net: intel: implement modern PM ops declarations igb: simplify pci ops declaration ==================== Link: https://lore.kernel.org/r/20240329175632.211340-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-01i40e: Fix VF MAC filter removalIvan Vecera
Commit 73d9629e1c8c ("i40e: Do not allow untrusted VF to remove administratively set MAC") fixed an issue where untrusted VF was allowed to remove its own MAC address although this was assigned administratively from PF. Unfortunately the introduced check is wrong because it causes that MAC filters for other MAC addresses including multi-cast ones are not removed. <snip> if (ether_addr_equal(addr, vf->default_lan_addr.addr) && i40e_can_vf_change_mac(vf)) was_unimac_deleted = true; else continue; if (i40e_del_mac_filter(vsi, al->list[i].addr)) { ... </snip> The else path with `continue` effectively skips any MAC filter removal except one for primary MAC addr when VF is allowed to do so. Fix the check condition so the `continue` is only done for primary MAC address. Fixes: 73d9629e1c8c ("i40e: Do not allow untrusted VF to remove administratively set MAC") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240329180638.211412-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-01ice: hold devlink lock for whole init/cleanupMichal Swiatkowski
Simplify devlink lock code in driver by taking it for whole init/cleanup path. Instead of calling devlink functions that taking lock call the lockless versions. Suggested-by: Jiri Pirko <jiri@resnulli.us> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: move devlink port code to a separate filePiotr Raczynski
Keep devlink related code in a separate file. More devlink port code and handlers will be added here for other port operations. Remove no longer needed include of our devlink.h in ice_lib.c. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: move ice_devlink.[ch] to devlink folderMichal Swiatkowski
Only moving whole files, fixing Makefile and bunch of includes. Some changes to ice_devlink file was done even in representor part (Tx topology), so keep it as final patch to not mess up with rebasing. After moving to devlink folder there is no need to have such long name for these files. Rename them to simple devlink. Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: Remove newlines in NL_SET_ERR_MSG_MODThorsten Blum
Fixes Coccinelle/coccicheck warnings reported by newline_in_nl_msg.cocci. Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: Add switch recipe reusing featureSteven Zou
New E810 firmware supports the corresponding functionality, so the driver allows PFs to subscribe the same switch recipes. Then when the PF is done with a switch recipes, the PF can ask firmware to free that switch recipe. When users configure a rule to PFn into E810 switch component, if there is no existing recipe matching this rule's pattern, the driver will request firmware to allocate and return a new recipe resource for the rule by calling ice_add_sw_recipe() and ice_alloc_recipe(). If there is an existing recipe matching this rule's pattern with different key value, or this is a same second rule to PFm into switch component, the driver checks out this recipe by calling ice_find_recp(), the driver will tell firmware to share using this same recipe resource by calling ice_subscribable_recp_shared() and ice_subscribe_recipe(). When firmware detects that all subscribing PFs have freed the switch recipe, firmware will free the switch recipe so that it can be reused. This feature also fixes a problem where all switch recipes would eventually be exhausted because switch recipes could not be freed, as freeing a shared recipe could potentially break other PFs that were using it. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Andrii Staikov <andrii.staikov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Steven Zou <steven.zou@intel.com> Tested-by: Mayank Sharma <mayank.sharma@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: fold ice_ptp_read_time into ice_ptp_gettimex64Michal Schmidt
This is a cleanup. It is unnecessary to have this function just to call another function. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: avoid the PTP hardware semaphore in gettimex64 pathMichal Schmidt
The PTP hardware semaphore (PFTSYN_SEM) is used to synchronize operations that program the PTP timers. The operations involve issuing commands to the sideband queue. The E810 does not have a hardware sideband queue, so the admin queue is used. The admin queue is slow. I have observed delays in hundreds of milliseconds waiting for ice_sq_done. When phc2sys reads the time from the ice PTP clock and PFTSYN_SEM is held by a task performing one of the slow operations, ice_ptp_lock can easily time out. phc2sys gets -EBUSY and the kernel prints: ice 0000:XX:YY.0: PTP failed to get time These messages appear once every few seconds, causing log spam. The E810 datasheet recommends an algorithm for reading the upper 64 bits of the GLTSYN_TIME register. It matches what's implemented in ice_ptp_read_src_clk_reg. It is robust against wrap-around, but not necessarily against the concurrent setting of the register (with GLTSYN_CMD_{INIT,ADJ}_TIME commands). Perhaps that's why ice_ptp_gettimex64 also takes PFTSYN_SEM. The race with time setters can be prevented without relying on the PTP hardware semaphore. Using the "ice_adapter" from the previous patch, we can have a common spinlock for the PFs that share the clock hardware. It will protect the reading and writing to the GLTSYN_TIME register. The writing is performed indirectly, by the hardware, as a result of the driver writing GLTSYN_CMD_SYNC in ice_ptp_exec_tmr_cmd. I wasn't sure if the ice_flush there is enough to make sure GLTSYN_TIME has been updated, but it works well in my testing. My test code can be seen here: https://gitlab.com/mschmidt2/linux/-/commits/ice-ptp-host-side-lock-10 It consists of: - kernel threads reading the time in a busy loop and looking at the deltas between consecutive values, reporting new maxima. - a shell script that sets the time repeatedly; - a bpftrace probe to produce a histogram of the measured deltas. Without the spinlock ptp_gltsyn_time_lock, it is easy to see tearing. Deltas in the [2G, 4G) range appear in the histograms. With the spinlock added, there is no tearing and the biggest delta I saw was in the range [1M, 2M), that is under 2 ms. Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: add ice_adapter for shared data across PFs on the same NICMichal Schmidt
There is a need for synchronization between ice PFs on the same physical adapter. Add a "struct ice_adapter" for holding data shared between PFs of the same multifunction PCI device. The struct is refcounted - each ice_pf holds a reference to it. Its first use will be for PTP. I expect it will be useful also to improve the ugliness that is ice_prot_id_tbl. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-04-01ice: Add support for PFCP hardware offload in switchdevMarcin Szycik
Add support for creating PFCP filters in switchdev mode. Add support for parsing PFCP-specific tc options: S flag and SEID. To create a PFCP filter, a special netdev must be created and passed to tc command: ip link add pfcp0 type pfcp tc filter add dev eth0 ingress prio 1 flower pfcp_opts \ 1:123/ff:fffffffffffffff0 skip_hw action mirred egress redirect \ dev pfcp0 Changes in iproute2 [1] are required to be able to use pfcp_opts in tc. ICE COMMS package is required to create a filter as it contains PFCP profiles. Link: https://lore.kernel.org/netdev/20230614091758.11180-1-marcin.szycik@linux.intel.com [1] Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-01ice: refactor ICE_TC_FLWR_FIELD_ENC_OPTSMarcin Szycik
FLOW_DISSECTOR_KEY_ENC_OPTS can be used for multiple headers, but currently it is treated as GTP-exclusive in ice. Rename ICE_TC_FLWR_FIELD_ENC_OPTS to ICE_TC_FLWR_FIELD_GTP_OPTS and check for tunnel type earlier. After this refactor, it is easier to add new headers using FLOW_DISSECTOR_KEY_ENC_OPTS - instead of checking tunnel type in ice_tc_count_lkups() and ice_tc_fill_tunnel_outer(), it needs to be checked only once, in ice_parse_tunnel_attr(). Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-03-29netlink: introduce type-checking attribute iterationJohannes Berg
There are, especially with multi-attr arrays, many cases of needing to iterate all attributes of a specific type in a netlink message or a nested attribute. Add specific macros to support that case. Also convert many instances using this spatch: @@ iterator nla_for_each_attr; iterator name nla_for_each_attr_type; identifier nla; expression head, len, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_attr(nla, head, len, rem) +nla_for_each_attr_type(nla, ATTR, head, len, rem) { <... T x; ...> -if (nla_type(nla) == ATTR) { ... -} } @@ identifier nla; iterator nla_for_each_nested; iterator name nla_for_each_nested_type; expression attr, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_nested(nla, attr, rem) +nla_for_each_nested_type(nla, ATTR, attr, rem) { <... T x; ...> -if (nla_type(nla) == ATTR) { ... -} } @@ iterator nla_for_each_attr; iterator name nla_for_each_attr_type; identifier nla; expression head, len, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_attr(nla, head, len, rem) +nla_for_each_attr_type(nla, ATTR, head, len, rem) { <... T x; ...> -if (nla_type(nla) != ATTR) continue; ... } @@ identifier nla; iterator nla_for_each_nested; iterator name nla_for_each_nested_type; expression attr, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_nested(nla, attr, rem) +nla_for_each_nested_type(nla, ATTR, attr, rem) { <... T x; ...> -if (nla_type(nla) != ATTR) continue; ... } Although I had to undo one bad change this made, and I also adjusted some other code for whitespace and to use direct variable initialization now. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20240328203144.b5a6c895fb80.I1869b44767379f204998ff44dd239803f39c23e0@changeid Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-29Merge branch '40GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-03-26 (i40e) This series contains updates to i40e driver only. Ivan Vecera resolves an issue where descriptors could be missed when exiting busy poll. Aleksandr corrects counting of MAC filters to only include new or active filters and resolves possible use of incorrect/stale 'vf' variable. * '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: i40e: fix vf may be used uninitialized in this function warning i40e: fix i40e_count_filters() to count only active/new filters i40e: Enforce software interrupt during busy-poll exit ==================== Link: https://lore.kernel.org/r/20240326162358.1224145-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-29i40e: avoid forward declarations in i40e_nvm.cMaciej Fijalkowski
Move code around to get rid of forward declarations. No functional changes. After a plain code juggling, checkpatch reported: total: 0 errors, 7 warnings, 12 checks, 1581 lines checked so while at it let's address old issues as well. Should we ever address the remaining unnecessary forward declarations within drivers/net/ethernet/intel/, consider this change as a starting point/reference. As reported in [0], there would be a lot more of work to do...if we care. [0]: https://lore.kernel.org/intel-wired-lan/Zeh8qadiTGf413YU@boxer/T/#u Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-29igc: Refactor runtime power management flowSasha Neftin
Following the corresponding discussion [1] and [2] refactor the 'igc_open' method and avoid taking the rtnl_lock() during the 'igc_resume' method. The rtnl_lock is held by the upper layer and could lead to the deadlock during resuming from a runtime power management flow. Notify the stack of the actual queue counts 'netif_set_real_num_*_queues' outside the '_igc_open' wrapper. This notification doesn't have to be called on each resume. Test: 1. Disconnect the ethernet cable 2. Enable the runtime power management via file system: echo auto > /sys/devices/pci0000\.../power/control 3. Check the device state (lspci -s <device> -vvv | grep -i Status) Link: https://lore.kernel.org/netdev/20231206113934.8d7819857574.I2deb5804 ef1739a2af307283d320ef7d82456494@changeid/#r [1] Link: https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedo ra-pc1c0hjn.dhcp.thefacebook.com/t/ [2] Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-29net: intel: implement modern PM ops declarationsJesse Brandeburg
Switch the Intel networking drivers to use the new power management ops declaration formats and macros, which allows us to drop __maybe_unused, as well as a bunch of ifdef checking CONFIG_PM. This is safe to do because the compiler drops the unused functions, verified by checking for any of the power management function symbols being present in System.map for a build without CONFIG_PM. If a driver has runtime PM, define the ops with pm_ptr(), and if the driver has Simple PM, use pm_sleep_ptr(), as well as the new versions of the macros for declaring the members of the pm_ops structs. Checked with network-enabled allnoconfig, allyesconfig, allmodconfig on x64_64. Reviewed-by: Alan Brady <alan.brady@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-29igb: simplify pci ops declarationJesse Brandeburg
The igb driver was pre-declaring tons of functions just so that it could have an early declaration of the pci_driver struct. Delete a bunch of the declarations and move the struct to the bottom of the file, after all the functions are declared. Reviewed-by: Alan Brady <alan.brady@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-28Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== ice: use less resources in switchdev Michal Swiatkowski says: Switchdev is using one queue per created port representor. This can quickly lead to Rx queue shortage, as with subfunction support user can create high number of PRs. Save one MSI-X and 'number of PRs' * 1 queues. Refactor switchdev slow-path to use less resources (even no additional resources). Do this by removing control plane VSI and move its functionality to PF VSI. Even with current solution PF is acting like uplink and can't be used simultaneously for other use cases (adding filters can break slow-path). In short, do Tx via PF VSI and Rx packets using PF resources. Rx needs additional code in interrupt handler to choose correct PR netdev. Previous solution had to queue filters, it was way more elegant but needed one queue per PRs. Beside that this refactor mostly simplifies switchdev configuration. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: count representor stats ice: do switchdev slow-path Rx using PF VSI ice: change repr::id values ice: remove switchdev control plane VSI ice: control default Tx rule in lag ice: default Tx rule instead of to queue ice: do Tx through PF netdev in slow-path ice: remove eswitch changing queues algorithm ==================== Link: https://lore.kernel.org/r/20240325202623.1012287-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28Merge branch '1GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-03-27 (e1000e) This series contains updates to e1000e driver only. Vitaly adds retry mechanism for some PHY operations to workaround MDI error and moves SMBus configuration to avoid possible PHY loss. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue e1000e: Workaround for sporadic MDI error on Meteor Lake systems ==================== Link: https://lore.kernel.org/r/20240327185517.2587564-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28idpf: sprinkle __counted_by{,_le}() in the virtchnl2 headerAlexander Lobakin
Both virtchnl2.h and its consumer idpf_virtchnl.c are very error-prone. There are 10 structures with flexible arrays at the end, but 9 of them has flex member counter in Little Endian. Make the code a bit more robust by applying __counted_by_le() to those 9. LE platforms is the main target for this driver, so they would receive additional protection. While we're here, add __counted_by() to virtchnl2_ptype::proto_id, as its counter is `u8` regardless of the Endianness. Compile test on x86_64 (LE) didn't reveal any new issues after applying the attributes. Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://lore.kernel.org/r/20240327142241.1745989-4-aleksander.lobakin@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28idpf: make virtchnl2.h self-containedAlexander Lobakin
To ease maintaining of virtchnl2.h, which already is messy enough, make it self-contained by adding missing if_ether.h include due to %ETH_ALEN usage. At the same time, virtchnl2_lan_desc.h is not used anywhere in the file, so move this include to idpf_txrx.h to speed up C preprocessing. Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://lore.kernel.org/r/20240327142241.1745989-3-aleksander.lobakin@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: remove gfp_mask from napi_alloc_skb()Jakub Kicinski
__napi_alloc_skb() is napi_alloc_skb() with the added flexibility of choosing gfp_mask. This is a NAPI function, so GFP_ATOMIC is implied. The only practical choice the caller has is whether to set __GFP_NOWARN. But that's a false choice, too, allocation failures in atomic context will happen, and printing warnings in logs, effectively for a packet drop, is both too much and very likely non-actionable. This leads me to a conclusion that most uses of napi_alloc_skb() are simply misguided, and should use __GFP_NOWARN in the first place. We also have a "standard" way of reporting allocation failures via the queue stat API (qstats::rx-alloc-fail). The direct motivation for this patch is that one of the drivers used at Meta calls napi_alloc_skb() (so prior to this patch without __GFP_NOWARN), and the resulting OOM warning is the top networking warning in our fleet. Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240327040213.3153864-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28Merge tag 'net-6.9-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from bpf, WiFi and netfilter. Current release - regressions: - ipv6: fix address dump when IPv6 is disabled on an interface Current release - new code bugs: - bpf: temporarily disable atomic operations in BPF arena - nexthop: fix uninitialized variable in nla_put_nh_group_stats() Previous releases - regressions: - bpf: protect against int overflow for stack access size - hsr: fix the promiscuous mode in offload mode - wifi: don't always use FW dump trig - tls: adjust recv return with async crypto and failed copy to userspace - tcp: properly terminate timers for kernel sockets - ice: fix memory corruption bug with suspend and rebuild - at803x: fix kernel panic with at8031_probe - qeth: handle deferred cc1 Previous releases - always broken: - bpf: fix bug in BPF_LDX_MEMSX - netfilter: reject table flag and netdev basechain updates - inet_defrag: prevent sk release while still in use - wifi: pick the version of SESSION_PROTECTION_NOTIF - wwan: t7xx: split 64bit accesses to fix alignment issues - mlxbf_gige: call request_irq() after NAPI initialized - hns3: fix kernel crash when devlink reload during pf initialization" * tag 'net-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits) inet: inet_defrag: prevent sk release while still in use Octeontx2-af: fix pause frame configuration in GMP mode net: lan743x: Add set RFE read fifo threshold for PCI1x1x chips net: bcmasp: Remove phy_{suspend/resume} net: bcmasp: Bring up unimac after PHY link up net: phy: qcom: at803x: fix kernel panic with at8031_probe netfilter: arptables: Select NETFILTER_FAMILY_ARP when building arp_tables.c netfilter: nf_tables: skip netdev hook unregistration if table is dormant netfilter: nf_tables: reject table flag and netdev basechain updates netfilter: nf_tables: reject destroy command to remove basechain hooks bpf: update BPF LSM designated reviewer list bpf: Protect against int overflow for stack access size bpf: Check bloom filter map value size bpf: fix warning for crash_kexec selftests: netdevsim: set test timeout to 10 minutes net: wan: framer: Add missing static inline qualifiers mlxbf_gige: call request_irq() after NAPI initialized tls: get psock ref after taking rxlock to avoid leak selftests: tls: add test with a partially invalid iov tls: adjust recv return with async crypto and failed copy to userspace ...
2024-03-27e1000e: move force SMBUS from enable ulp function to avoid PHY loss issueVitaly Lifshits
Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on some systems. It is suspected to be caused by initiating PHY transactions before the interface settles. Separating this configuration from the ULP enabling flow and moving it to the shutdown function allows enough time for the interface to settle and avoids adding a delay. Fixes: 6607c99e7034 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state") Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-27e1000e: Workaround for sporadic MDI error on Meteor Lake systemsVitaly Lifshits
On some Meteor Lake systems accessing the PHY via the MDIO interface may result in an MDI error. This issue happens sporadically and in most cases a second access to the PHY via the MDIO interface results in success. As a workaround, introduce a retry counter which is set to 3 on Meteor Lake systems. The driver will only return an error if 3 consecutive PHY access attempts fail. The retry mechanism is disabled in specific flows, where MDI errors are expected. Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake") Suggested-by: Nikolay Mushayev <nikolay.mushayev@intel.com> Co-developed-by: Nir Efrati <nir.efrati@intel.com> Signed-off-by: Nir Efrati <nir.efrati@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26i40e: fix vf may be used uninitialized in this function warningAleksandr Loktionov
To fix the regression introduced by commit 52424f974bc5, which causes servers hang in very hard to reproduce conditions with resets races. Using two sources for the information is the root cause. In this function before the fix bumping v didn't mean bumping vf pointer. But the code used this variables interchangeably, so stale vf could point to different/not intended vf. Remove redundant "v" variable and iterate via single VF pointer across whole function instead to guarantee VF pointer validity. Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26i40e: fix i40e_count_filters() to count only active/new filtersAleksandr Loktionov
The bug usually affects untrusted VFs, because they are limited to 18 MACs, it affects them badly, not letting to create MAC all filters. Not stable to reproduce, it happens when VF user creates MAC filters when other MACVLAN operations are happened in parallel. But consequence is that VF can't receive desired traffic. Fix counter to be bumped only for new or active filters. Fixes: 621650cabee5 ("i40e: Refactoring VF MAC filters counting to make more reliable") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26i40e: Enforce software interrupt during busy-poll exitIvan Vecera
As for ice bug fixed by commit b7306b42beaf ("ice: manage interrupts during poll exit") followed by commit 23be7075b318 ("ice: fix software generating extra interrupts") I'm seeing the similar issue also with i40e driver. In certain situation when busy-loop is enabled together with adaptive coalescing, the driver occasionally misses that there are outstanding descriptors to clean when exiting busy poll. Try to catch the remaining work by triggering a software interrupt when exiting busy poll. No extra interrupts will be generated when busy polling is not used. The issue was found when running sockperf ping-pong tcp test with adaptive coalescing and busy poll enabled (50 as value busy_pool and busy_read sysctl knobs) and results in huge latency spikes with more than 100000us. The fix is inspired from the ice driver and do the following: 1) During napi poll exit in case of busy-poll (napo_complete_done() returns false) this is recorded to q_vector that we were in busy loop. 2) Extends i40e_buildreg_itr() to be able to add an enforced software interrupt into built value 2) In i40e_update_enable_itr() enforces a software interrupt trigger if we are exiting busy poll to catch any pending clean-ups 3) Reuses unused 3rd ITR (interrupt throttle) index and set it to 20K interrupts per second to limit the number of these sw interrupts. Test results ============ Prior: [root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120 sockperf: == version #3.10-no.git == sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s) [ 0] IP = 10.9.9.1 PORT = 11111 # TCP sockperf: Warmup stage (sending a few dummy messages)... sockperf: Starting test... sockperf: Test end (interrupted by timer) sockperf: Test ended sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2438563; ReceivedMessages=2438562 sockperf: ========= Printing statistics for Server No: 0 sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2429473; ReceivedMessages=2429473 sockperf: ====> avg-latency=24.571 (std-dev=93.297, mean-ad=4.904, median-ad=1.510, siqr=1.063, cv=3.797, std-error=0.060, 99.0% ci=[24.417, 24.725]) sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0 sockperf: Summary: Latency is 24.571 usec sockperf: Total 2429473 observations; each percentile contains 24294.73 observations sockperf: ---> <MAX> observation = 103294.331 sockperf: ---> percentile 99.999 = 45.633 sockperf: ---> percentile 99.990 = 37.013 sockperf: ---> percentile 99.900 = 35.910 sockperf: ---> percentile 99.000 = 33.390 sockperf: ---> percentile 90.000 = 28.626 sockperf: ---> percentile 75.000 = 27.741 sockperf: ---> percentile 50.000 = 26.743 sockperf: ---> percentile 25.000 = 25.614 sockperf: ---> <MIN> observation = 12.220 After: [root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120 sockperf: == version #3.10-no.git == sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s) [ 0] IP = 10.9.9.1 PORT = 11111 # TCP sockperf: Warmup stage (sending a few dummy messages)... sockperf: Starting test... sockperf: Test end (interrupted by timer) sockperf: Test ended sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2400055; ReceivedMessages=2400054 sockperf: ========= Printing statistics for Server No: 0 sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2391186; ReceivedMessages=2391186 sockperf: ====> avg-latency=24.965 (std-dev=5.934, mean-ad=4.642, median-ad=1.485, siqr=1.067, cv=0.238, std-error=0.004, 99.0% ci=[24.955, 24.975]) sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0 sockperf: Summary: Latency is 24.965 usec sockperf: Total 2391186 observations; each percentile contains 23911.86 observations sockperf: ---> <MAX> observation = 195.841 sockperf: ---> percentile 99.999 = 45.026 sockperf: ---> percentile 99.990 = 39.009 sockperf: ---> percentile 99.900 = 35.922 sockperf: ---> percentile 99.000 = 33.482 sockperf: ---> percentile 90.000 = 28.902 sockperf: ---> percentile 75.000 = 27.821 sockperf: ---> percentile 50.000 = 26.860 sockperf: ---> percentile 25.000 = 25.685 sockperf: ---> <MIN> observation = 12.277 Fixes: 0bcd952feec7 ("ethernet/intel: consolidate NAPI and NAPI exit") Reported-by: Hugo Ferreira <hferreir@redhat.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: count representor statsMichal Swiatkowski
Removing control plane VSI result in no information about slow-path statistic. In current solution statistics need to be counted in driver. Patch is based on similar implementation done by Simon Horman in nfp: commit eadfa4c3be99 ("nfp: add stats and xmit helpers for representors") Add const modifier to netdev parameter in ice_netdev_to_repr(). It isn't (and shouldn't be) modified in the function. Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: do switchdev slow-path Rx using PF VSIMichal Swiatkowski
Add an ICE_RX_FLAG_MULTIDEV flag to Rx ring. If it is set try to find correct port representor. Do it based on src_vsi value stored in flex descriptor. Ids of representor pointers stored in xarray are equal to corresponding src_vsi value. Thanks to that we can directly get correct representor if we have src_vsi value. Set multidev flag during ring configuration. If the mode is switchdev, change the ring descriptor to the one that contains src_vsi value. PF netdev should be reconfigured, do it by calling ice_down() and ice_up() if the netdev was up before configuring switchdev. Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: change repr::id valuesMichal Swiatkowski
Instead of getting repr::id from xa_alloc() value, set it to the src_vsi::num_vsi value. It is unique for each PR. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: remove switchdev control plane VSIMichal Swiatkowski
For slow-path Rx and Tx PF VSI is used. There is no need to have control plane VSI. Remove all code related to it. Eswitch rebuild can't fail without rebuilding control plane VSI. Return void from ice_eswitch_rebuild(). Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: control default Tx rule in lagMichal Swiatkowski
Tx rule in switchdev was changed to use PF instead of additional control plane VSI. Because of that during lag we should control it. Control means to add and remove the default Tx rule during lag active/inactive switching. It can be done the same way as default Rx rule. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: default Tx rule instead of to queueMichal Swiatkowski
Steer all packets that miss other rules to PF VSI. Previously in switchdev mode, PF VSI received missed packets, but only ones marked as Rx. Now it is receiving all missed packets. To queue rule per PR isn't needed, because we use PF VSI instead of control VSI now, and it's already correctly configured. Add flag to correctly set LAN_EN bit in default Tx rule. It shouldn't allow packet to go outside when there is a match. Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: do Tx through PF netdev in slow-pathMichal Swiatkowski
Tx can be done using PF netdev. Checks before Tx are unnecessary. Checking if switchdev mode is set seems too defensive (there is no PR netdev in legacy mode). If corresponding VF is disabled or during reset, PR netdev also should be down. Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: remove eswitch changing queues algorithmMichal Swiatkowski
Changing queues used by eswitch will be done through PF netdev. There is no need to reserve queues if the number of used queues is known. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25igc: Remove stale comment about Tx timestampingKurt Kanzenbach
The initial igc Tx timestamping implementation used only one register for retrieving Tx timestamps. Commit 3ed247e78911 ("igc: Add support for multiple in-flight TX timestamps") added support for utilizing all four of them e.g., for multiple domain support. Remove the stale comment/FIXME. Fixes: 3ed247e78911 ("igc: Add support for multiple in-flight TX timestamps") Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ixgbe: avoid sleeping allocation in ixgbe_ipsec_vf_add_sa()Przemek Kitszel
Change kzalloc() flags used in ixgbe_ipsec_vf_add_sa() to GFP_ATOMIC, to avoid sleeping in IRQ context. Dan Carpenter, with the help of Smatch, has found following issue: The patch eda0333ac293: "ixgbe: add VF IPsec management" from Aug 13, 2018 (linux-next), leads to the following Smatch static checker warning: drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c:917 ixgbe_ipsec_vf_add_sa() warn: sleeping in IRQ context The call tree that Smatch is worried about is: ixgbe_msix_other() <- IRQ handler -> ixgbe_msg_task() -> ixgbe_rcv_msg_from_vf() -> ixgbe_ipsec_vf_add_sa() Fixes: eda0333ac293 ("ixgbe: add VF IPsec management") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/intel-wired-lan/db31a0b0-4d9f-4e6b-aed8-88266eb5665c@moroto.mountain Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
generated by cgit (git 2.34.1) at 2025-07-24 02:46:10 +0000