| Age | Commit message (Collapse) | Author |
|---|
|
Split the XLG and GMAC PCS implementations and switch between them
during the mac_prepare() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert mvpp2 to phylink's new pcs support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the GMAC reset handling into mac_prepare() / mac_finish()
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Ensure that the port is forced down while reconfiguring, controlling
this via mac_prepare() and mac_finish() so that it is down while we
are configuring our (future) PCS.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert mvpp2 to use the mac_prepare() and mac_finish() methods in
preparation to converting mvpp2 to split-PCS support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Tidy up the ACPI hack so that we can minimise the function prototypes
for this. This avoids adding further prototypes unnecessarily.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Fill in the phy interface mode bitmap for the Marvell mvpp2 driver, so
phylink can know which interfaces are supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Set the flow control settings in mvpp2_mac_link_up() for 10G links
just as we do for 1G and slower links. This is now the preferred
location.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a helper to read-modify-write a register, and use it in the phylink
helpers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a helper to convert the struct phylink_config pointer passed in
from phylink to the drivers internal struct mvpp2_port.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The mvpp2 code has tests scattered amongst the code to determine
whether the port supports the XLG, and whether the port supports
RGMII mode.
Rather than having these tests scattered, provide a couple of helper
functions, so that future additions can ensure that they get these
tests correct.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without 895586d5dc32 and with 895586d5dc32 applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with 895586d5dc32, failing: 00200000 40000000
- without 895586d5dc32, working: 04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc32, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "info->fs.location" is a u32 that comes from the user via the
ethtool_set_rxnfc() function. We need to check for invalid values to
prevent a buffer overflow.
I copy and pasted this check from the mvpp2_ethtool_cls_rule_ins()
function.
Fixes: 90b509b39ac9 ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "rss_context" variable comes from the user via ethtool_get_rxfh().
It can be any u32 value except zero. Eventually it gets passed to
mvpp22_rss_ctx() and if it is over MVPP22_N_RSS_TABLES (8) then it
results in an array overflow.
Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the Marvell mvpp2 ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mere overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presently, at boot time, the comphys are enabled. For firmware
compatibility reasons, the comphy driver does not power down the
comphys at boot. Consequently, the ethernet comphys are left active
until the network interfaces are brought through an up/down cycle.
If the port is never used, the port wastes power needlessly. Arrange
for the ethernet comphys to be cycled by the mvpp2 driver as if the
interface went through an up/down cycle during driver probe, thereby
powering them down.
This saves:
270mW per 10G SFP+ port on the Macchiatobin Single Shot (eth0/eth1)
370mW per 10G PHY port on the Macchiatobin Double Shot (eth0/eth1)
160mW on the SFP port on either Macchiatobin flavour (eth3)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up the mvpp2 validate implementation to adopt the same behaviour as
mvneta:
- only allow the link modes that the specified PHY interface mode
supports with the exception of 1000base-X and 2500base-X.
- use the basex helper to deal with SFP modules that can be switched
between 1000base-X vs 2500base-X.
This gives consistent behaviour between mvneta and mvpp2.
This commit depends on "net: phylink: extend clause 45 PHY validation
workaround" so is not marked for backporting to stable kernels.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb043262878 ("net: mvpp2: phylink support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
When receiving traffic, eth_type_trans() is high up on the perf top list,
because it's the first function which access the packet data.
Move the DMA unmap a bit higher, and put a prefetch just after it, so we
have more time to load the data into the cache.
The packet rate increase is about 14% with a tc drop test: 1620 => 1853 kpps
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the RX path we always sync against the maximum frame size for that pool.
Do the DMA sync and the unmap separately, so we can only sync by the
size of the received frame.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move some code down to remove a backward goto.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recycling in mvpp2 has gone long time ago, but two comment still refers
to it. Remove those two misleading comments as they generate confusion.
Fixes: 7ef7e1d949cd ("net: mvpp2: drop useless fields in mvpp2_bm_pool and related code")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_done_tasklet tasklet is used in invoke the hrtimer
(mvpp2_hr_timer_cb) in softirq context. This can be also achieved without
the tasklet but with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Huckleberry <nhuck@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just minor overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mvpp2 uses a delayed workqueue to gather traffic statistics.
On module removal the workqueue can be destroyed before calling
cancel_delayed_work_sync() on its works.
Fix it by moving the destroy_workqueue() call after mvpp2_port_remove().
Also remove an unneeded call to flush_workqueue()
# rmmod mvpp2
[ 2743.311722] mvpp2 f4000000.ethernet eth1: phy link down 10gbase-kr/10Gbps/Full
[ 2743.320063] mvpp2 f4000000.ethernet eth1: Link is Down
[ 2743.572263] mvpp2 f4000000.ethernet eth2: phy link down sgmii/1Gbps/Full
[ 2743.580076] mvpp2 f4000000.ethernet eth2: Link is Down
[ 2744.102169] mvpp2 f2000000.ethernet eth0: phy link down 10gbase-kr/10Gbps/Full
[ 2744.110441] mvpp2 f2000000.ethernet eth0: Link is Down
[ 2744.115614] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 2744.115615] Mem abort info:
[ 2744.115616] ESR = 0x96000005
[ 2744.115617] Exception class = DABT (current EL), IL = 32 bits
[ 2744.115618] SET = 0, FnV = 0
[ 2744.115619] EA = 0, S1PTW = 0
[ 2744.115620] Data abort info:
[ 2744.115621] ISV = 0, ISS = 0x00000005
[ 2744.115622] CM = 0, WnR = 0
[ 2744.115624] user pgtable: 4k pages, 39-bit VAs, pgdp=0000000422681000
[ 2744.115626] [0000000000000000] pgd=0000000000000000, pud=0000000000000000
[ 2744.115630] Internal error: Oops: 96000005 [#1] SMP
[ 2744.115632] Modules linked in: mvpp2(-) algif_hash af_alg nls_iso8859_1 nls_cp437 vfat fat xhci_plat_hcd m25p80 spi_nor xhci_hcd mtd usbcore i2c_mv64xxx sfp usb_common marvell10g phy_generic spi_orion mdio_i2c i2c_core mvmdio phylink sbsa_gwdt ip_tables x_tables autofs4 [last unloaded: mvpp2]
[ 2744.115654] CPU: 3 PID: 8357 Comm: kworker/3:2 Not tainted 5.3.0-rc2 #1
[ 2744.115655] Hardware name: Marvell 8040 MACCHIATOBin Double-shot (DT)
[ 2744.115665] Workqueue: events_power_efficient phylink_resolve [phylink]
[ 2744.115669] pstate: a0000085 (NzCv daIf -PAN -UAO)
[ 2744.115675] pc : __queue_work+0x9c/0x4d8
[ 2744.115677] lr : __queue_work+0x170/0x4d8
[ 2744.115678] sp : ffffff801001bd50
[ 2744.115680] x29: ffffff801001bd50 x28: ffffffc422597600
[ 2744.115684] x27: ffffff80109ae6f0 x26: ffffff80108e4018
[ 2744.115688] x25: 0000000000000003 x24: 0000000000000004
[ 2744.115691] x23: ffffff80109ae6e0 x22: 0000000000000017
[ 2744.115694] x21: ffffffc42c030000 x20: ffffffc42209e8f8
[ 2744.115697] x19: 0000000000000000 x18: 0000000000000000
[ 2744.115699] x17: 0000000000000000 x16: 0000000000000000
[ 2744.115701] x15: 0000000000000010 x14: ffffffffffffffff
[ 2744.115702] x13: ffffff8090e2b95f x12: ffffff8010e2b967
[ 2744.115704] x11: ffffff8010906000 x10: 0000000000000040
[ 2744.115706] x9 : ffffff80109223b8 x8 : ffffff80109223b0
[ 2744.115707] x7 : ffffffc42bc00068 x6 : 0000000000000000
[ 2744.115709] x5 : ffffffc42bc00000 x4 : 0000000000000000
[ 2744.115710] x3 : 0000000000000000 x2 : 0000000000000000
[ 2744.115712] x1 : 0000000000000008 x0 : ffffffc42c030000
[ 2744.115714] Call trace:
[ 2744.115716] __queue_work+0x9c/0x4d8
[ 2744.115718] delayed_work_timer_fn+0x28/0x38
[ 2744.115722] call_timer_fn+0x3c/0x180
[ 2744.115723] expire_timers+0x60/0x168
[ 2744.115724] run_timer_softirq+0xbc/0x1e8
[ 2744.115727] __do_softirq+0x128/0x320
[ 2744.115731] irq_exit+0xa4/0xc0
[ 2744.115734] __handle_domain_irq+0x70/0xc0
[ 2744.115735] gic_handle_irq+0x58/0xa8
[ 2744.115737] el1_irq+0xb8/0x140
[ 2744.115738] console_unlock+0x3a0/0x568
[ 2744.115740] vprintk_emit+0x200/0x2a0
[ 2744.115744] dev_vprintk_emit+0x1c8/0x1e4
[ 2744.115747] dev_printk_emit+0x6c/0x7c
[ 2744.115751] __netdev_printk+0x104/0x1d8
[ 2744.115752] netdev_printk+0x60/0x70
[ 2744.115756] phylink_resolve+0x38c/0x3c8 [phylink]
[ 2744.115758] process_one_work+0x1f8/0x448
[ 2744.115760] worker_thread+0x54/0x500
[ 2744.115762] kthread+0x12c/0x130
[ 2744.115764] ret_from_fork+0x10/0x1c
[ 2744.115768] Code: aa1403e0 97fffbbe aa0003f5 b4000700 (f9400261)
Fixes: 118d6298f6f0 ("net: mvpp2: add ethtool GOP statistics")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware can only offload checksum calculation on first port due to
the Tx FIFO size limitation, and has a maximum L3 offset of 128 bytes.
Document this in a comment and move duplicated code in a function.
Fixes: 576193f2d579 ("net: mvpp2: jumbo frames support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTU change code can call napi_disable() with the device already down,
leading to a deadlock. Also, lot of code is duplicated unnecessarily.
Rework mvpp2_change_mtu() to avoid the deadlock and remove duplicated code.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPv2's XLGMAC can wait for 3 idle frames before triggering a link up
event. This can cause the link to be stuck low when there's traffic on
the interface, so disable this feature.
Fixes: 4bb043262878 ("net: mvpp2: phylink support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two cases of overlapping changes, nothing fancy.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Users can specify classification actions based on the 'ether' flow type.
In that case, this will apply to all ethernet traffic, superseeding
flows such as 'udp4' or 'tcp6'.
Add support for this flow type in the PPv2 classifier, by mapping the
ETHER_FLOW value to the corresponding entries in the classifier.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a missing check to detect flow types that we don't support, so that
user can be informed of this.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Header Parser allows identifying various fields in the packet
headers, used for various kind of filtering and classification
steps.
This is a re-entrant process, where the offset in the packet header
depends on the previous lookup results. This offset is represented in
the SRAM results of the TCAM, as a shift to be operated.
This shift can be negative in some cases, such as in IPv6 parsing.
This commit prevents overriding the sign bit when setting the shift
value, which could cause instabilities when parsing IPv6 flows.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Suggested-by: Alan Winkowski <walan@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor SPDX change conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was an unused variable 'mvpp2_dbgfs_prs_pmap_fops'
Added a usage consistent with other fops to dump pmap
to userspace.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/529
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit allows using the vlan Id and priority as parts of the key
for classification offload. These fields are extracted from the
outermost tag, if multiple tags are present.
Vlan Id and priority are considered as 2 different fields by the
classifier, however the fields are both appended in the Header Extracted
Key in the same layout as they are found in the tags. This means that
when steering only based on the prio, a 16-bit slot is still taken in
the HEK.
The classifier doesn't allow extracting the DEI bit from the tag, so we
explicitly prevent user from using this bit in the key.
This commit adds the vlan priotity as a compatible HEK field for
tagged traffic, meaning that we limit the possibility of extracting this
field only to the flows that contain tagged traffic.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The C2 TCAM used for classification uses a key (Header Extracted Key)
built by concatenating several fields extracted from the packet header.
After a lot of trial-and-error and some guess work, it seems the HEK is
right justified, with the first fields being stored in the MSB, then
concatenated up until the LSB.
Until now, this doesn't cause any issue since all HEK fields we use are
full bytes. However this is an issue for the upcoming VLAN id and pri
extraction, which aren't full bytes.
Rework the way we built that TCAM key, by changing the order in which we
append the fields.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The way we currently handle classification offload and RSS is by having
dedicated lookup sequences in the flow table, each being selected
depending on several fields being present in the packet header.
We need to make sure the classification operation we want to perform can
be done in each flow we want to insert it into. As an example,
classifying on VLAN tag can only be done on flows used for tagged
traffic.
This commit makes sure we don't insert rules in flows we aren't
compatible with.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When performing a TCAM lookup in the C2 engine, it's possible that
multiple entries match the packet. To make sure the correct entry match
when performing a lookup, the Flow Table can set a lookup type, which
will be used in the TCAM lookup, thus preventing such false-positives.
We need to make sure the RSS match doesn't interfere with other
classification lookups, hence we use a dedicated lookup_type for it.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
