summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/mellanox/mlx4
AgeCommit message (Collapse)Author
2018-07-20Merge ra.kernel.org:/pub/scm/linux/kernel/git/torvalds/linuxDavid S. Miller
All conflicts were trivial overlapping changes, so reasonably easy to resolve. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-16net/mlx4_en: Don't reuse RX page when XDP is setSaeed Mahameed
When a new rx packet arrives, the rx path will decide whether to reuse the remainder of the page or not according to one of the below conditions: 1. frag_info->frag_stride == PAGE_SIZE / 2 2. frags->page_offset + frag_info->frag_size > PAGE_SIZE; The first condition is no met for when XDP is set. For XDP, page_offset is always set to priv->rx_headroom which is XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some padding, still the 2nd release condition will hold since XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not be released and will be _wrongly_ reused for next free rx descriptor. In XDP there is an assumption to have a page per packet and reuse can break such assumption and might cause packet data corruptions. Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd case to avoid page reuse when XDP is set, since rx_headroom is set to 0 for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup. No additional cache line is required for the new condition. Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Suggested-by: Martin KaFai Lau <kafai@fb.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller
Daniel Borkmann says: ==================== pull-request: bpf-next 2018-07-15 The following pull-request contains BPF updates for your *net-next* tree. The main changes are: 1) Various different arm32 JIT improvements in order to optimize code emission and make the JIT code itself more robust, from Russell. 2) Support simultaneous driver and offloaded XDP in order to allow for advanced use-cases where some work is offloaded to the NIC and some to the host. Also add ability for bpftool to load programs and maps beyond just the cgroup case, from Jakub. 3) Add BPF JIT support in nfp for multiplication as well as division. For the latter in particular, it uses the reciprocal algorithm to emulate it, from Jiong. 4) Add BTF pretty print functionality to bpftool in plain and JSON output format, from Okash. 5) Add build and installation to the BPF helper man page into bpftool, from Quentin. 6) Add a TCP BPF callback for listening sockets which is triggered right after the socket transitions to TCP_LISTEN state, from Andrey. 7) Add a new cgroup tree command to bpftool which iterates over the whole cgroup tree and prints all attached programs, from Roman. 8) Improve xdp_redirect_cpu sample to support parsing of double VLAN tagged packets, from Jesper. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-13xdp: don't make drivers report attachment modeJakub Kicinski
prog_attached of struct netdev_bpf should have been superseded by simply setting prog_id long time ago, but we kept it around to allow offloading drivers to communicate attachment mode (drv vs hw). Subsequently drivers were also allowed to report back attachment flags (prog_flags), and since nowadays only programs attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell the attachment mode from the flags driver reports. Remove prog_attached member. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-07-12net/mlx4_core: Use devlink region_snapshot parameterAlex Vesker
This parameter enables capturing region snapshot of the crspace during critical errors. The default value of this parameter is disabled, it can be enabled using devlink param commands. It is possible to configure during runtime and also driver init. Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12net/mlx4_core: Add Crdump FW snapshot supportAlex Vesker
Crdump allows the driver to create a snapshot of the FW PCI crspace and health buffer during a critical FW issue. In case of a FW command timeout, FW getting stuck or a non zero value on the catastrophic buffer, a snapshot will be taken. The snapshot is exposed using devlink, cr-space, fw-health address regions are registered on init and snapshots are attached once a new snapshot is collected by the driver. Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12net/mlx4_core: Add health buffer address capabilityAlex Vesker
Health buffer address is a 32 bit PCI address offset provided by the FW. This offset is used for reading FW health debug data located on the shared CR space. Cr space is accessible in both driver and FW and allows for different queries and configurations. Health buffer size is always 64B of readable data followed by a lock which is used to block volatile CR space access. Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-09net: allow fallback function to pass netdevAlexander Duyck
For most of these calls we can just pass NULL through to the fallback function as the sb_dev. The only cases where we cannot are the cases where we might be dealing with either an upper device or a driver that would have configured things to support an sb_dev itself. The only driver that has any significant change in this patch set should be ixgbe as we can drop the redundant functionality that existed in both the ndo_select_queue function and the fallback function that was passed through to us. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-07-09net: allow ndo_select_queue to pass netdevAlexander Duyck
This patch makes it so that instead of passing a void pointer as the accel_priv we instead pass a net_device pointer as sb_dev. Making this change allows us to pass the subordinate device through to the fallback function eventually so that we can keep the actual code in the ndo_select_queue call as focused on possible on the exception cases. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-07-05mlx4: Add support for devlink reload and load driverinit valuesMoshe Shemesh
Add mlx4_devlink_reload() to support devlink reload operation. Add mlx4_devlink_param_load_driverinit_values() to load values which were set using driverinit configuration mode. Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05mlx4: Add mlx4 initial parameters table and register itMoshe Shemesh
Create initial parameters table for mlx4. The table consists of two generic parameters and two driver-specific parameters. Generic: internal_err_reset - Enable reset device on internal errors. This parameter can be configured on mlx4 either on runtime or during driver initialization. max_macs - Max number of MACs per ETH port. For mlx4 this parameter value range is between 1 and 128. This parameter can be configured on mlx4 only during driver initialization. Driver specific: enable_64b_cqe_eqe - Enable 64 byte CQEs/EQEs when the FW supports it. This parameter can be configured on mlx4 only during driver initialization. enable_4k_uar - Enable using 4K UAR. This parameter can be configured on mlx4 only during driver initialization. Register the parameters table on mlx4_init_one() and unregister on mlx4_remove_one(). Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-12treewide: kvzalloc() -> kvcalloc()Kees Cook
The kvzalloc() function has a 2-factor argument form, kvcalloc(). This patch replaces cases of: kvzalloc(a * b, gfp) with: kvcalloc(a * b, gfp) as well as handling cases of: kvzalloc(a * b * c, gfp) with: kvzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kvcalloc(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kvzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kvzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kvzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kvzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kvzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kvzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kvzalloc( - sizeof(char) * COUNT + COUNT , ...) | kvzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kvzalloc + kvcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kvzalloc + kvcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kvzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kvzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kvzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kvzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kvzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kvzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kvzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kvzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kvzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kvzalloc(C1 * C2 * C3, ...) | kvzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kvzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kvzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kvzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kvzalloc(sizeof(THING) * C2, ...) | kvzalloc(sizeof(TYPE) * C2, ...) | kvzalloc(C1 * C2 * C3, ...) | kvzalloc(C1 * C2, ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kvzalloc + kvcalloc ( - (E1) * E2 + E1, E2 , ...) | - kvzalloc + kvcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kvzalloc + kvcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12treewide: kmalloc() -> kmalloc_array()Kees Cook
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2018-06-04net: ethernet: mlx4: Remove unnecessary parenthesesVarsha Rao
This patch fixes the clang warning of extraneous parentheses, with the following coccinelle script. @@ identifier i; expression e; statement s; @@ if ( -(i == e) +i == e ) s Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Varsha Rao <rvarsha016@gmail.com> Acked-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03mlx4_core: restore optimal ICM memory allocationEric Dumazet
Commit 1383cb8103bb ("mlx4_core: allocate ICM memory in page size chunks") brought two regressions caught in our regression suite. The big one is an additional cost of 256 bytes of overhead per 4096 bytes, or 6.25 % which is unacceptable since ICM can be pretty large. This comes from having to allocate one struct mlx4_icm_chunk (256 bytes) per MLX4_TABLE_CHUNK, which the buggy commit shrank to 4KB (instead of prior 256KB) Note that mlx4_alloc_icm() is already able to try high order allocations and fallback to low-order allocations under high memory pressure. Most of these allocations happen right after boot time, when we get plenty of non fragmented memory, there is really no point being so pessimistic and break huge pages into order-0 ones just for fun. We only have to tweak gfp_mask a bit, to help falling back faster, without risking OOM killings. Second regression is an KASAN fault, that will need further investigations. Fixes: 1383cb8103bb ("mlx4_core: allocate ICM memory in page size chunks") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Tariq Toukan <tariqt@mellanox.com> Cc: John Sperbeck <jsperbeck@google.com> Cc: Tarick Bedeir <tarick@google.com> Cc: Qing Huang <qing.huang@oracle.com> Cc: Daniel Jurgens <danielj@mellanox.com> Cc: Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Lots of easy overlapping changes in the confict resolutions here. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-25mlx4_core: allocate ICM memory in page size chunksQing Huang
When a system is under memory presure (high usage with fragments), the original 256KB ICM chunk allocations will likely trigger kernel memory management to enter slow path doing memory compact/migration ops in order to complete high order memory allocations. When that happens, user processes calling uverb APIs may get stuck for more than 120s easily even though there are a lot of free pages in smaller chunks available in the system. Syslog: ... Dec 10 09:04:51 slcc03db02 kernel: [397078.572732] INFO: task oracle_205573_e:205573 blocked for more than 120 seconds. ... With 4KB ICM chunk size on x86_64 arch, the above issue is fixed. However in order to support smaller ICM chunk size, we need to fix another issue in large size kcalloc allocations. E.g. Setting log_num_mtt=30 requires 1G mtt entries. With the 4KB ICM chunk size, each ICM chunk can only hold 512 mtt entries (8 bytes for each mtt entry). So we need a 16MB allocation for a table->icm pointer array to hold 2M pointers which can easily cause kcalloc to fail. The solution is to use kvzalloc to replace kcalloc which will fall back to vmalloc automatically if kmalloc fails. Signed-off-by: Qing Huang <qing.huang@oracle.com> Acked-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-23net/mlx4: Fix irq-unsafe spinlock usageJack Morgenstein
spin_lock/unlock was used instead of spin_un/lock_irq in a procedure used in process space, on a spinlock which can be grabbed in an interrupt. This caused the stack trace below to be displayed (on kernel 4.17.0-rc1 compiled with Lock Debugging enabled): [ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected [ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I [ 154.675856] ----------------------------------------------------- [ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core] [ 154.700927] and this task is already holding: [ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib] [ 154.718028] which would create a new lock dependency: [ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.} [ 154.731922] but this new dependency connects a SOFTIRQ-irq-safe lock: [ 154.740798] (&(&cq->lock)->rlock){..-.} [ 154.740800] ... which became SOFTIRQ-irq-safe at: [ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50 [ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib] [ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib] ... to a SOFTIRQ-irq-unsafe lock: [ 154.815603] (&(&qp_table->lock)->rlock){+.+.} [ 154.815604] ... which became SOFTIRQ-irq-unsafe at: [ 154.827718] ... [ 154.827720] _raw_spin_lock+0x35/0x50 [ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core] [ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core] Since mlx4_qp_lookup() is called only in process space, we can simply replace the spin_un/lock calls with spin_un/lock_irq calls. Fixes: 6dc06c08bef1 ("net/mlx4: Fix the check in attaching steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-23net/mlx4: fix spelling mistake: "Inrerface" -> "Interface" and rephrase messageColin Ian King
Trivial fix to spelling mistake in mlx4_dbg debug message and also change the phrasing of the message so that is is more readable Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
S390 bpf_jit.S is removed in net-next and had changes in 'net', since that code isn't used any more take the removal. TLS data structures split the TX and RX components in 'net-next', put the new struct members from the bug fix in 'net' into the RX part. The 'net-next' tree had some reworking of how the ERSPAN code works in the GRE tunneling code, overlapping with a one-line headroom calculation fix in 'net'. Overlapping changes in __sock_map_ctx_update_elem(), keep the bits that read the prog members via READ_ONCE() into local variables before using them. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14net/mlx4_core: Fix error handling in mlx4_init_port_info.Tarick Bedeir
Avoid exiting the function with a lingering sysfs file (if the first call to device_create_file() fails while the second succeeds), and avoid calling devlink_port_unregister() twice. In other words, either mlx4_init_port_info() succeeds and returns zero, or it fails, returns non-zero, and requires no cleanup. Fixes: 096335b3f983 ("mlx4_core: Allow dynamic MTU configuration for IB ports") Signed-off-by: Tarick Bedeir <tarick@google.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
The bpf syscall and selftests conflicts were trivial overlapping changes. The r8169 change involved moving the added mdelay from 'net' into a different function. A TLS close bug fix overlapped with the splitting of the TLS state into separate TX and RX parts. I just expanded the tests in the bug fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf == X". Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10net/mlx4_en: Fix an error handling path in 'mlx4_en_init_netdev()'Christophe JAILLET
If an error occurs, 'mlx4_en_destroy_netdev()' is called. It then calls 'mlx4_en_free_resources()' which does the needed resources cleanup. So, doing some explicit kfree in the error handling path would lead to some double kfree. Simplify code to avoid such a case. Fixes: 67f8b1dcb9ee ("net/mlx4_en: Refactor the XDP forwarding rings scheme") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10net/mlx4_en: Verify coalescing parameters are in rangeMoshe Shemesh
Add check of coalescing parameters received through ethtool are within range of values supported by the HW. Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the users through ethtool. The ethtool support up to 32 bit value for each. However, mlx4 modify cq limits the coalescing time parameter and coalescing frames parameters to 16 bits. Return out of range error if user tries to set these parameters to higher values. Change type of sample-interval and adaptive_rx_coal parameters in mlx4 driver to u32 as the ethtool holds them as u32 and these parameters are not limited due to mlx4 HW. Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10net/mlx4_core: Use msi_x module param to limit num of MSI-X irqsTariq Toukan
Extend the boolean interpretation of msi_x module parameter to numerical, as follows: 0 - Don't use MSI-X. 1 - Use MSI-X, driver decides the num of MSI-X irqs. >=2 - Use MSI-X, limit number of MSI-X irqs to msi_x. In SRIOV, this limits the number of MSI-X irqs per VF. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Cc: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com> Reviewed-by: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10net/mlx4_core: Add PCI calls for suspend/resumeYishai Hadas
Implement suspend/resume callbacks in struct pci_driver. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10net/mlx4_core: Report driver version to FWEran Ben Elisha
If supported, write a driver version string to FW as part of the INIT_HCA command. Example of driver version: "Linux,mlx4_core,4.0-0" Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-04net/mlx4_en: optimizes get_fixed_ipv6_csum()Eric Dumazet
While trying to support CHECKSUM_COMPLETE for IPV6 fragments, I had to experiments various hacks in get_fixed_ipv6_csum(). I must admit I could not find how to implement this :/ However, get_fixed_ipv6_csum() does a lot of redundant operations, calling csum_partial() twice. First csum_partial() computes the checksum of saddr and daddr, put in @csum_pseudo_hdr. Undone later in the second csum_partial() computed on whole ipv6 header. Then nexthdr is added once, added a second time, then substracted. payload_len is added once, then substracted. Really all this can be reduced to two add_csum(), to add back 6 bytes that were removed by mlx4 when providing hw_checksum in RX descriptor. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Overlapping changes in selftests Makefile. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-01net/mlx4: fix spelling mistake: "failedi" -> "failed"Colin Ian King
trivial fix to spelling mistake in mlx4_warn message. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-29mlx4: Don't bother using skb_tx_hash in mlx4_en_select_queueAlexander Duyck
The code in the fallback path has supported XDP in conjunction with the Tx traffic classification for TCs for over a year now. So instead of just calling skb_tx_hash for every packet we are better off using the fallback since that will record the Tx queue to the socket and then that can be used instead of having to recompute the hash every time. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18bpf: make mlx4 compatible w/ bpf_xdp_adjust_tailNikita V. Shirokov
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as well (only "decrease" of pointer's location is going to be supported). changing of this pointer will change packet's size. for mlx4 driver we will just calculate packet's length unconditionally (the same way as it's already being done in mlx5) Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-04-06Merge tag 'pci-v4.17-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: - move pci_uevent_ers() out of pci.h (Michael Ellerman) - skip ASPM common clock warning if BIOS already configured it (Sinan Kaya) - fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva) - remove last user of pci_get_bus_and_slot() and the function itself (Sinan Kaya) - add decoding for 16 GT/s link speed (Jay Fang) - add interfaces to get max link speed and width (Tal Gilboa) - add pcie_bandwidth_capable() to compute max supported link bandwidth (Tal Gilboa) - add pcie_bandwidth_available() to compute bandwidth available to device (Tal Gilboa) - add pcie_print_link_status() to log link speed and whether it's limited (Tal Gilboa) - use PCI core interfaces to report when device performance may be limited by its slot instead of doing it in each driver (Tal Gilboa) - fix possible cpqphp NULL pointer dereference (Shawn Lin) - rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI hotplug (Mika Westerberg) - add support for PCI I/O port space that's neither directly accessible via CPU in/out instructions nor directly mapped into CPU physical memory space. This is fairly intrusive and includes minor changes to interfaces used for I/O space on most platforms (Zhichang Yuan, John Garry) - add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan, John Garry) - use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas) - remove possible NULL pointer dereference in of_pci_bus_find_domain_nr() (Shawn Lin) - report quirk timings with dev_info (Bjorn Helgaas) - report quirks that take longer than 10ms (Bjorn Helgaas) - add and use Altera Vendor ID (Johannes Thumshirn) - tidy Makefiles and comments (Bjorn Helgaas) - don't set up INTx if MSI or MSI-X is enabled to align cris, frv, ia64, and mn10300 with x86 (Bjorn Helgaas) - move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick Lawler) - merge pcieport_if.h into portdrv.h (Bjorn Helgaas) - move workaround for BIOS PME issue from portdrv to PCI core (Bjorn Helgaas) - completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas) - remove portdrv link order dependency (Bjorn Helgaas) - remove support for unused VC portdrv service (Bjorn Helgaas) - simplify portdrv feature permission checking (Bjorn Helgaas) - remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn Helgaas) - remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas) - use cached AER capability offset (Frederick Lawler) - don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg) - rename pcie-dpc.c to dpc.c (Bjorn Helgaas) - use generic pci_mmap_resource_range() instead of powerpc and xtensa arch-specific versions (David Woodhouse) - support arbitrary PCI host bridge offsets on sparc (Yinghai Lu) - remove System and Video ROM reservations on sparc (Bjorn Helgaas) - probe for device reset support during enumeration instead of runtime (Bjorn Helgaas) - add ACS quirk for Ampere (née APM) root ports (Feng Kan) - add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas Vincent-Cross) - protect device restore with device lock (Sinan Kaya) - handle failure of FLR gracefully (Sinan Kaya) - handle CRS (config retry status) after device resets (Sinan Kaya) - skip various config reads for SR-IOV VFs as an optimization (KarimAllah Ahmed) - consolidate VPD code in vpd.c (Bjorn Helgaas) - add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann) - add DT support for R-Car r8a7743 (Biju Das) - fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host bridge driver that causes a general protection fault (Dexuan Cui) - fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV (Dexuan Cui) - fix Hyper-V host bridge hang when ejecting a VF before setting up MSI (Dexuan Cui) - make several structures static (Fengguang Wu) - increase number of MSI IRQs supported by Synopsys DesignWare bridges from 32 to 256 (Gustavo Pimentel) - implemented multiplexed IRQ domain API and remove obsolete MSI IRQ API from DesignWare drivers (Gustavo Pimentel) - add Tegra power management support (Manikanta Maddireddy) - add Tegra loadable module support (Manikanta Maddireddy) - handle 64-bit BARs correctly in endpoint support (Niklas Cassel) - support optional regulator for HiSilicon STB (Shawn Guo) - use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla) - support power supplies for Qualcomm msm8996 (Srinivas Kandagatla) * tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits) MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver HISI LPC: Add ACPI support ACPI / scan: Do not enumerate Indirect IO host children ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings of: Add missing I/O range exception for indirect-IO devices PCI: Apply the new generic I/O management on PCI IO hosts PCI: Add fwnode handler as input param of pci_register_io_range() PCI: Remove __weak tag from pci_register_io_range() MAINTAINERS: Add missing /drivers/pci/cadence directory entry fm10k: Report PCIe link properties with pcie_print_link_status() net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth net/mlx5: Report PCIe link properties with pcie_print_link_status() net/mlx4_core: Report PCIe link properties with pcie_print_link_status() PCI: Add pcie_print_link_status() to log link speed and whether it's limited PCI: Add pcie_bandwidth_available() to compute bandwidth available to device misc: pci_endpoint_test: Handle 64-bit BARs properly PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar ...
2018-04-06Merge tag 'for-linus-unmerged' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma Pull rdma updates from Jason Gunthorpe: "Doug and I are at a conference next week so if another PR is sent I expect it to only be bug fixes. Parav noted yesterday that there are some fringe case behavior changes in his work that he would like to fix, and I see that Intel has a number of rc looking patches for HFI1 they posted yesterday. Parav is again the biggest contributor by patch count with his ongoing work to enable container support in the RDMA stack, followed by Leon doing syzkaller inspired cleanups, though most of the actual fixing went to RC. There is one uncomfortable series here fixing the user ABI to actually work as intended in 32 bit mode. There are lots of notes in the commit messages, but the basic summary is we don't think there is an actual 32 bit kernel user of drivers/infiniband for several good reasons. However we are seeing people want to use a 32 bit user space with 64 bit kernel, which didn't completely work today. So in fixing it we required a 32 bit rxe user to upgrade their userspace. rxe users are still already quite rare and we think a 32 bit one is non-existing. - Fix RDMA uapi headers to actually compile in userspace and be more complete - Three shared with netdev pull requests from Mellanox: * 7 patches, mostly to net with 1 IB related one at the back). This series addresses an IRQ performance issue (patch 1), cleanups related to the fix for the IRQ performance problem (patches 2-6), and then extends the fragmented completion queue support that already exists in the net side of the driver to the ib side of the driver (patch 7). * Mostly IB, with 5 patches to net that are needed to support the remaining 10 patches to the IB subsystem. This series extends the current 'representor' framework when the mlx5 driver is in switchdev mode from being a netdev only construct to being a netdev/IB dev construct. The IB dev is limited to raw Eth queue pairs only, but by having an IB dev of this type attached to the representor for a switchdev port, it enables DPDK to work on the switchdev device. * All net related, but needed as infrastructure for the rdma driver - Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers - SRP performance updates - IB uverbs write path cleanup patch series from Leon - Add RDMA_CM support to ib_srpt. This is disabled by default. Users need to set the port for ib_srpt to listen on in configfs in order for it to be enabled (/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port) - TSO and Scatter FCS support in mlx4 - Refactor of modify_qp routine to resolve problems seen while working on new code that is forthcoming - More refactoring and updates of RDMA CM for containers support from Parav - mlx5 'fine grained packet pacing', 'ipsec offload' and 'device memory' user API features - Infrastructure updates for the new IOCTL interface, based on increased usage - ABI compatibility bug fixes to fully support 32 bit userspace on 64 bit kernel as was originally intended. See the commit messages for extensive details - Syzkaller bugs and code cleanups motivated by them" * tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (199 commits) IB/rxe: Fix for oops in rxe_register_device on ppc64le arch IB/mlx5: Device memory mr registration support net/mlx5: Mkey creation command adjustments IB/mlx5: Device memory support in mlx5_ib net/mlx5: Query device memory capabilities IB/uverbs: Add device memory registration ioctl support IB/uverbs: Add alloc/free dm uverbs ioctl support IB/uverbs: Add device memory capabilities reporting IB/uverbs: Expose device memory capabilities to user RDMA/qedr: Fix wmb usage in qedr IB/rxe: Removed GID add/del dummy routines RDMA/qedr: Zero stack memory before copying to user space IB/mlx5: Add ability to hash by IPSEC_SPI when creating a TIR IB/mlx5: Add information for querying IPsec capabilities IB/mlx5: Add IPsec support for egress and ingress {net,IB}/mlx5: Add ipsec helper IB/mlx5: Add modify_flow_action_esp verb IB/mlx5: Add implementation for create and destroy action_xfrm IB/uverbs: Introduce ESP steering match filter IB/uverbs: Add modify ESP flow_action ...
2018-04-03net/mlx4_core: Report PCIe link properties with pcie_print_link_status()Tal Gilboa
Use pcie_print_link_status() to report PCIe link speed and possible limitations instead of implementing this in the driver itself. Signed-off-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> [bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2018-04-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c, we had some overlapping changes: 1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE --> MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE 2) In 'net-next' params->log_rq_size is renamed to be params->log_rq_mtu_frames. 3) In 'net-next' params->hard_mtu is added. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-01net/mlx4_en: CHECKSUM_COMPLETE support for fragmentsEric Dumazet
Refine the RX check summing handling to propagate the hardware provided checksum so that we do not have to compute it later in software. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Acked-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-27net/mlx4_core: Fix memory leak while delete slave's resourcesMoshe Shemesh
mlx4_delete_all_resources_for_slave in resource tracker should free all memory allocated for a slave. While releasing memory of fs_rule, it misses releasing memory of fs_rule->mirr_mbox. Fixes: 78efed275117 ('net/mlx4_core: Support mirroring VF DMFS rules on both ports') Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-27net/mlx4_en: Fix mixed PFC and Global pause user control requestsEran Ben Elisha
Global pause and PFC configuration should be mutually exclusive (i.e. only one of them at most can be set). However, once PFC was turned off, driver automatically turned Global pause on. This is a bug. Fix the driver behaviour to turn off PFC/Global once the user turned the other on. This also fixed a weird behaviour that at a current time, the profile had both PFC and global pause configuration turned on, which is Hardware-wise impossible and caused returning false positive indication to query tools. In addition, fix error code when setting global pause or PFC to change metadata only upon successful change. Also, removed useless debug print. Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands") Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-26ethernet: Use octal not symbolic permissionsJoe Perches
Prefer the direct use of octal for permissions. Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace and some typing. Miscellanea: o Whitespace neatening around these conversions. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-15RDMA/mlx4: Move flag constants to uapi headerJason Gunthorpe
MLX4_USER_DEV_CAP_LARGE_CQE (via mlx4_ib_alloc_ucontext_resp.dev_caps) and MLX4_IB_QUERY_DEV_RESP_MASK_CORE_CLOCK_OFFSET (via mlx4_uverbs_ex_query_device_resp.comp_mask) are copied directly to userspace and form part of the uAPI. Move them to the uapi header where they belong. Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-07net/mlx4_en: try to use high order pages for RX ringsEric Dumazet
RX rings can fit most of the time in a contiguous piece of memory, so lets use kvzalloc_node/kvfree instead of vzalloc_node/vfree Note that kvzalloc_node() automatically falls back to another node, there is no need to do the fallback ourselves. Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27net/mlx4_en: RX csum, pre-define enabled protocols for IP status maskingTariq Toukan
Pre-define a mask for IP status of a completion, that tests the MLX4_CQE_STATUS_IPV6 only in case CONFIG_IPV6 is enabled. Use it for IP status testing upon completion, instead of separating the datapath into two flows. This takes common code structures (such as closing parenthesis) back to their original place, and makes code more readable. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Suggested-by: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27net/mlx4_en: Combine checks of end-cases in RX completion functionTariq Toukan
Combine two end-cases in the same if statement with a single return value. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27net/mlx4_en: Remove unnecessary warn print in reset configEran Ben Elisha
In mlx4_en_reset_config, there was a redundant warn print that was left from previous versions of this function. No warn is needed anymore. This warn can be confusing when RX-FCS is changed: Turn OFF RX-FCS: mlx4_en: eth1: Changing device configuration rx filter(0) rx vlan(1) Turn ON RX-FCS: mlx4_en: eth1: Changing device configuration rx filter(0) rx vlan(1) Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27net/mlx4_en: Add physical RX/TX bytes/packets countersEran Ben Elisha
Add physical RX/TX packets/bytes counters into ethtool output to monitor all traffic that was received and transmitted on the port. These counters are available only for none Virtual Function. Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Significantly shrink the core networking routing structures. Result of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf 2) Add netdevsim driver for testing various offloads, from Jakub Kicinski. 3) Support cross-chip FDB operations in DSA, from Vivien Didelot. 4) Add a 2nd listener hash table for TCP, similar to what was done for UDP. From Martin KaFai Lau. 5) Add eBPF based queue selection to tun, from Jason Wang. 6) Lockless qdisc support, from John Fastabend. 7) SCTP stream interleave support, from Xin Long. 8) Smoother TCP receive autotuning, from Eric Dumazet. 9) Lots of erspan tunneling enhancements, from William Tu. 10) Add true function call support to BPF, from Alexei Starovoitov. 11) Add explicit support for GRO HW offloading, from Michael Chan. 12) Support extack generation in more netlink subsystems. From Alexander Aring, Quentin Monnet, and Jakub Kicinski. 13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From Russell King. 14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso. 15) Many improvements and simplifications to the NFP driver bpf JIT, from Jakub Kicinski. 16) Support for ipv6 non-equal cost multipath routing, from Ido Schimmel. 17) Add resource abstration to devlink, from Arkadi Sharshevsky. 18) Packet scheduler classifier shared filter block support, from Jiri Pirko. 19) Avoid locking in act_csum, from Davide Caratti. 20) devinet_ioctl() simplifications from Al viro. 21) More TCP bpf improvements from Lawrence Brakmo. 22) Add support for onlink ipv6 route flag, similar to ipv4, from David Ahern. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits) tls: Add support for encryption using async offload accelerator ip6mr: fix stale iterator net/sched: kconfig: Remove blank help texts openvswitch: meter: Use 64-bit arithmetic instead of 32-bit tcp_nv: fix potential integer overflow in tcpnv_acked r8169: fix RTL8168EP take too long to complete driver initialization. qmi_wwan: Add support for Quectel EP06 rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK ipmr: Fix ptrdiff_t print formatting ibmvnic: Wait for device response when changing MAC qlcnic: fix deadlock bug tcp: release sk_frag.page in tcp_disconnect ipv4: Get the address of interface correctly. net_sched: gen_estimator: fix lockdep splat net: macb: Handle HRESP error net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring ipv6: addrconf: break critical section in addrconf_verify_rtnl() ipv6: change route cache aging logic i40e/i40evf: Update DESC_NEEDED value to reflect larger value bnxt_en: cleanup DIM work on device shutdown ...
2018-01-30Merge tag v4.15 of ↵Jason Gunthorpe
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git To resolve conflicts in: drivers/infiniband/hw/mlx5/main.c drivers/infiniband/hw/mlx5/qp.c From patches merged into the -rc cycle. The conflict resolution matches what linux-next has been carrying. Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
generated by cgit (git 2.34.1) at 2025-06-01 17:02:15 +0000