| Age | Commit message (Collapse) | Author |
|---|
|
As explained in the previous patch, the existing Spectrum-2 ip6gre
implementation can be reused for Spectrum-1. Change the Spectrum-1
ip6gre operations structure to use the common operations.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are two main differences between Spectrum-1 and newer ASICs in
terms of IP-in-IP support:
1. In Spectrum-1, RIFs representing ip6gre tunnels require two entries
in the RIF table.
2. In Spectrum-2 and newer ASICs, packets ingress the underlay (during
encapsulation) and egress the underlay (during decapsulation) via a
special generic loopback RIF.
The first difference was handled in previous patches by adding the
'double_rif_entry' field to the Spectrum-1 operations structure of
ip6gre RIFs. The second difference is handled during RIF creation, by
only creating a generic loopback RIF in Spectrum-2 and newer ASICs.
Therefore, the ip6gre operations can be shared between Spectrum-1 and
newer ASIC in a similar fashion to how the ipgre operations are shared.
Rename the operations to not be Spectrum-2 specific and move them
earlier in the file so that they could later be used for Spectrum-1.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In Spectrum-1, loopback router interfaces (RIFs) used for IP-in-IP
encapsulation with an IPv6 underlay require two RIF entries and the RIF
index must be even.
Prepare for this change by extending the RIF parameters structure with a
'double_entry' field that indicates if the RIF being created requires
two RIF entries or not. Only set it for RIFs representing ip6gre tunnels
in Spectrum-1.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, each router interface (RIF) consumes one entry in the RIFs
table. This is going to change in subsequent patches where some RIFs
will consume two table entries.
Prepare for this change by parametrizing the RIF allocation size. For
now, always pass '1'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, each router interface (RIF) consumes one entry in the RIFs
table and there are no alignment constraints. This is going to change in
subsequent patches where some RIFs will consume two table entries and
their indexes will need to be aligned to the allocation size (even).
Prepare for this change by converting the RIF index allocation to use
gen_pool with the 'gen_pool_first_fit_order_align' algorithm.
No Kconfig changes necessary as mlxsw already selects
'GENERIC_ALLOCATOR'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
include/linux/bpf.h
1f6e04a1c7b8 ("bpf: Fix offset calculation error in __copy_map_value and zero_map_value")
aa3496accc41 ("bpf: Refactor kptr_off_tab into btf_record")
f71b2f64177a ("bpf: Refactor map->off_arr handling")
https://lore.kernel.org/all/20221114095000.67a73239@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mlxsw adjfine implementation in the spectrum_ptp.c file converts
scaled_ppm into ppb before updating a cyclecounter multiplier using the
standard "base * ppb / 1billion" calculation.
This can be re-written to use adjust_by_scaled_ppm, directly using the
scaled parts per million and reducing the amount of code required to
express this calculation.
We still calculate the parts per billion for passing into
mlxsw_sp_ptp_phc_adjfreq because this function requires the input to be in
parts per billion.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Amit Cohen <amcohen@nvidia.com>
Cc: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20221114213701.815132-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FDB entries that perform VXLAN encapsulation with an IPv6 underlay hold
a reference on a resource - the KVDL entry where the IPv6 underlay
destination IP is stored. For that, the driver maintains two hash tables:
1. Maps IPv6 to KVDL index
2. Maps {MAC, FID index} to IPv6 address
When a FDB entry is removed, the second table is used to find the relevant
IPv6 address and the first table is used to remove the reference count and
free the index if is not used anymore.
In order for a packet to be forwarded to a single remote VTEP, FDB
entries need to be configured at both the bridge and VXLAN devices' FDB
tables. Both entries are squashed into one {MAC, VLAN/VNI} -> IP entry
in the hardware. Therefore, in case one entry is removed, the entry will
be removed from the hardware and the remaining entry will be unmarked
with 'offload' flag since it is not offloaded anymore.
For example, the two FDB entries should be added to allow packets to be
forwarded via vx10:
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff self static dst 2001:db8:5::1
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff master static vlan 10
When one entry will be removed, the second one will not be offloaded
anymore. When the first entry (in VXLAN FDB) will be removed / will not be
offloaded anymore, the two mappings in IPv6 hash tables will be removed.
In case that the second entry is removed before the first one, unexpected
warnings[1][2] will be shown in user space as a result of removing the
first entry. The issue is that not offloaded entry is removed, the driver
tries to search the relevant entries in the hash tables, does not find them
and therefore warns.
Do not handle removing of not offloaded VXLAN FDB entries, as they were
already removed when the offload flag was removed.
[1]:
WARNING: CPU: 1 PID: 239 at drivers/net/ethernet/mellanox/mlxsw/spectrum_nve.c:914 mlxsw_sp_nve_ipv6_addr_map_del+0x6b/0x80 [mlxsw_spectrum]
...
Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015
Workqueue: mlxsw_core_ordered mlxsw_sp_switchdev_vxlan_fdb_event_work [mlxsw_spectrum]
RIP: 0010:mlxsw_sp_nve_ipv6_addr_map_del+0x6b/0x80 [mlxsw_spectrum]
...
Call Trace:
<TASK>
mlxsw_sp_port_fdb_tunnel_uc_op+0x6cf/0x7b0 [mlxsw_spectrum]
mlxsw_sp_switchdev_vxlan_fdb_event_work+0x17c/0x420 [mlxsw_spectrum]
? finish_task_switch.isra.0+0x8c/0x290
process_one_work+0x1cd/0x390
worker_thread+0x48/0x3c0
? process_one_work+0x390/0x390
kthread+0xe0/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
[2]:
WARNING: CPU: 0 PID: 239 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3035 mlxsw_sp_ipv6_addr_put+0x142/0x220 [mlxsw_spectrum]
...
Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015
Workqueue: mlxsw_core_ordered mlxsw_sp_switchdev_vxlan_fdb_event_work [mlxsw_spectrum]
RIP: 0010:mlxsw_sp_ipv6_addr_put+0x142/0x220 [mlxsw_spectrum]
...
Call Trace:
<TASK>
? mlxsw_sp_port_fdb_tun_uc_op6_sfd_write+0x5c1/0x610 [mlxsw_spectrum]
mlxsw_sp_port_fdb_tunnel_uc_op+0x6ec/0x7b0 [mlxsw_spectrum]
mlxsw_sp_switchdev_vxlan_fdb_event_work+0x17c/0x420 [mlxsw_spectrum]
? finish_task_switch.isra.0+0x8c/0x290
process_one_work+0x1cd/0x390
worker_thread+0x48/0x3c0
? process_one_work+0x390/0x390
kthread+0xe0/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 0860c7641634 ("mlxsw: spectrum_nve: Keep track of IPv6 addresses used by FDB entries")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/c186de8cbd28e3eb661e06f31f7f2f2dff30020f.1668184350.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add locked bridge port support by reacting to changes in the
'BR_PORT_LOCKED' flag. When set, enable security checks on the local
port via the previously added SPFSR register.
When security checks are enabled, an incoming packet will trigger an FDB
lookup with the packet's source MAC and the FID it was classified to. If
an FDB entry was not found or was found to be pointing to a different
port, the packet will be dropped. Such packets increment the
"discard_ingress_general" ethtool counter. For added visibility, user
space can trap such packets to the CPU by enabling the "locked_port"
trap. Example:
# devlink trap set pci/0000:06:00.0 trap locked_port action trap
Unlike other configurations done via bridge port flags (e.g., learning,
flooding), security checks are enabled in the device on a per-port basis
and not on a per-{port, VLAN} basis. As such, scenarios where user space
can configure different locking settings for different VLANs configured
on a port need to be vetoed. To that end, veto the following scenarios:
1. Locking is set on a bridge port that is a VLAN upper
2. Locking is set on a bridge port that has VLAN uppers
3. VLAN upper is configured on a locked bridge port
Examples:
# bridge link set dev swp1.10 locked on
Error: mlxsw_spectrum: Locked flag cannot be set on a VLAN upper.
# ip link add link swp1 name swp1.10 type vlan id 10
# bridge link set dev swp1 locked on
Error: mlxsw_spectrum: Locked flag cannot be set on a bridge port that has VLAN uppers.
# bridge link set dev swp1 locked on
# ip link add link swp1 name swp1.10 type vlan id 10
Error: mlxsw_spectrum: VLAN uppers are not supported on a locked port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Propagate extack to mlxsw_sp_port_attr_br_pre_flags_set() in order to
communicate error messages related to bridge port flag validation.
Example:
# bridge link set dev swp1 locked on
Error: mlxsw_spectrum: Unsupported bridge port flag.
More error messages will be added in subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In Spectrum, learning happens in parallel to the security checks.
Therefore, regardless of the result of the security checks, a learning
notification will be generated by the device and polled later on by the
driver.
Currently, the driver reacts to learning notifications by programming
corresponding FDB entries to the device. When a port is locked (i.e.,
has security checks enabled), this can no longer happen, as otherwise
any host will blindly gain authorization.
Instead, notify the learned entry as a locked entry to the bridge driver
that will in turn notify it to user space, in case MAB is enabled. User
space can then decide to authorize the host by clearing the "locked"
flag, which will cause the entry to be programmed to the device.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Subsequent patches will need to report locked FDB entries to the bridge
driver. Prepare for that by adding a 'locked' argument to
mlxsw_sp_fdb_call_notifiers() according to which the 'locked' bit is set
in the FDB notification info. For now, always pass 'false'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an API to enable or disable security checks on a local port. It will
be used by subsequent patches when the 'BR_PORT_LOCKED' flag is toggled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the Switch Port FDB Security Register (SPFSR) that allows enabling
and disabling security checks on a given local port. In Linux terms, it
allows locking / unlocking a port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Register the previously added packet traps with devlink. This allows
user space to tune their policers and in the case of the locked port
trap, user space can set its action to "trap" in order to gain
visibility into packets that were discarded by the device due to the
locked port check failure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove ndo_get_devlink_port which is no longer used alongside with the
implementations in drivers.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Benefit from the previously implemented tracking of netdev events in
devlink code and instead of calling devlink_port_type_eth_set() and
devlink_port_type_clear() to set devlink port type and link to related
netdev, use SET_NETDEV_DEVLINK_PORT() macro to assign devlink_port
pointer to netdevice which is about to be registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for 800Gbps speed, link modes of 100Gbps per lane.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"The most significant part of this update is the thermal control DT
initialization rework from Daniel Lezcano and the following conversion
of drivers to use the new API introduced by it
Apart from that, the maximum number of trip points in a thermal zone
is increased and there are some fixes and code cleanups
Specifics:
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after free
when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar)
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang)
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing)
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada)
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki)
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan)
- Drop redundant error message from da9062-thermal (zhaoxiao)
- Drop of_match_ptr() from thermal_mmio (Jean Delvare)"
* tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: core: Increase maximum number of trip points
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: Drop duplicate words from comments
thermal: move from strlcpy() with unused retval to strscpy()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
...
|
|
flexible array
To work around a misbehavior of the compiler's ability to see into
composite flexible array structs (as detailed in the coming memcpy()
hardening series[1]), split the memcpy() of the header and the payload
so no false positive run-time overflow warning will be generated.
[1] https://lore.kernel.org/linux-hardening/20220901065914.1417829-2-keescook@chromium.org
Cc: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20220927004033.1942992-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove all the code about SFTR-V2 Register which have been
deprecated since commit 77b7f83d5c25 ("mlxsw: Enable unified
bridge model").
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linux 6.0-rc5
|
|
Delete the redundant word 'in'.
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/.gitignore
sort the net-next version and use it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting from Spectrum-4, the maximum number of LAG IDs can be configured
by software via CONFIG_PROFILE command during driver initialization.
Add a dedicated instance of 'struct mlxsw_config_profile' for Spectrum-4
and set the 'max_lag' field to 128, which is the same amount of LAG entries
as in Spectrum-{2,3}. Without this configuration, firmware reserves 256
(the value of 'cap_max_lag' resource) entries at beginning of PGT table for
LAG identifiers, which means that less entries in PGT will be available.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the driver queries the maximum supported LAG ID from firmware.
This will not be accurate anymore once the driver will configure 'max_lag'
via CONFIG_PROFILE command.
For resource query, firmware returns the maximum LAG ID which is supported
by hardware. Software can configure firmware to do not allocate entries for
all the supported LAGs, and to limit LAG IDs. In this case, the resource
query will not return the actual maximum LAG ID.
Add a helper function for getting this value. In case that 'max_lag' field
was set during initialization, return the value which was used, otherwise,
query firmware for the maximum supported ID.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the device, LAG identifiers are stored in the port group table (PGT).
During initialization, firmware reserves a certain amount of entries at
the beginning of this table for LAG identifiers.
In Spectrum-4, the size of the PGT table did not increase, but the maximum
number of LAG identifiers was doubled, leaving less room for others entries
(e.g., flood entries) that also reside in the PGT.
Therefore, in order to avoid a regression and as long as there is no
explicit requirement to support 256 LAGs, mlxsw driver will configure the
firmware to allocate the same amount of LAG entries (128) as in
Spectrum-{2,3}. This configuration is done using 'max_lag' field in
CONFIG_PROFILE command. Extend 'struct mlxsw_config_profile' to support
'max_lag' field and configure firmware accordingly.
A next patch will adjust Spectrum-4 to configure 'max_lag' field.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting from Spectrum-4, the maximum number of LAG IDs can be configured
by software via CONFIG_PROFILE command during driver initialization.
Edit the comment of 'max_lag' field to mention that this field is reserved
in Spectrum-1/2/3 and describe firmware behavior.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These error paths return success but they should return -ENOMEM.
Fixes: 01328e23a476 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/YwjgwoJ3M7Kdq9VK@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel borkmann says:
====================
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 14 day(s) which contain
a total of 13 files changed, 61 insertions(+), 24 deletions(-).
The main changes are:
1) Fix BPF verifier's precision tracking around BPF ring buffer, from Kumar Kartikeya Dwivedi.
2) Fix regression in tunnel key infra when passing FLOWI_FLAG_ANYSRC, from Eyal Birger.
3) Fix insufficient permissions for bpf_sys_bpf() helper, from YiFei Zhu.
4) Fix splat from hitting BUG when purging effective cgroup programs, from Pu Lehui.
5) Fix range tracking for array poke descriptors, from Daniel Borkmann.
6) Fix corrupted packets for XDP_SHARED_UMEM in aligned mode, from Magnus Karlsson.
7) Fix NULL pointer splat in BPF sockmap sk_msg_recvmsg(), from Liu Jian.
8) Add READ_ONCE() to bpf_jit_limit when reading from sysctl, from Kuniyuki Iwashima.
9) Add BPF selftest lru_bug check to s390x deny list, from Daniel Müller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function mlxsw_core_port_type_get() is no longer used. So remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
port_type_set devlink op is no longer used by any mlxsw driver,
so remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are some IB leftovers that are no longer used in the code.
So remove them.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal control changes for v6.1-rc1 from Daniel Lezcano:
"- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already showed in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)"
* tag 'thermal-v6.1-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (46 commits)
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
thermal/core: Move set_trip_temp ops to the sysfs code
thermal/drivers/samsung: Switch to new of thermal API
regulator/drivers/max8976: Switch to new of thermal API
Input: sun4i-ts - switch to new of thermal API
iio/drivers/sun4i_gpadc: Switch to new of thermal API
hwmon/drivers/core: Switch to new of thermal API
hwmon: pm_bus: core: Switch to new of thermal API
ata/drivers/ahci_imx: Switch to new of thermal API
thermal/drivers/ti-soc: Switch to new of API
thermal/drivers/hisilicon: Switch to new of API
thermal/drivers/maxim: Switch to new of API
...
|
|
Implement line card operation callbacks got_active() / got_inactive().
The purpose of these callback to create / remove line card ports after
line card is getting active / inactive.
Implement line ports_remove_selected() callback to support line card
un-provisioning flow through 'devlink'.
Add line card operation registration and de-registration APIs.
Add module offset for line card. Offset for main board iz zero.
For line card in slot #n offset is calculated as (#n - 1) multiplied by
maximum modules number.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The interfaces for ports found on line card are created and removed
dynamically after line card is getting active or inactive.
Introduce per line card array with module to port mapping.
For each port get 'slot_index' through PMLP register and set port
mapping for the relevant [slot_index][module] entry.
Split module and port allocation into separate routines.
Split per line card port creation and removing into separate routines.
Motivation to re-use these routines for line card operations.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Perform ports allocation in a separate routine.
Motivation is to re-use this routine for ports found on line cards.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add 'slot_index' field to port structure.
Replace zero slot_index argument with 'slot_index' in 'ethtool'
related APIs.
Add 'slot_index' argument to port initialization and
de-initialization related APIs.
Motivation is to prepare minimal driver for modular system support.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extend i2c bus driver with interrupt handler to support system specific
hotplug events, related to line card state change.
Provide system IRQ line for interrupt handler. IRQ line Id could be
provided through the platform data if available, or could be set to the
default value.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add line card system event handler. Register it with core. It is
triggered by system interrupts raised from chassis programmable logic
devices to CPU. The purpose is to handle line card state changes over
I2C bus.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The purpose of system event handler is to handle system interrupts.
Such interrupts are raised to CPU from system programmable logic
devices, upon specific system wide changes, like line card activation
and deactivation.
The purpose is to create an alternative to trap mechanism, which
delivers these events to driver over PCI bus, but not available for
the driver working over I2C bus.
Mechanism is system dependent and applicable only for the systems
equipped with programmable devices with custom logic.
Add APIs for event handler registration and un-registration and API
which should be invoked from the registered callbacks when system
interrupt is raised to CPU.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, each line card is initialized using the following steps:
1. Initializing its various fields (e.g., slot index).
2. Creating the corresponding devlink object.
3. Enabling events (i.e., traps) for changes in line card status.
4. Querying and processing line card status.
Unlike traps, the IRQ that notifies the CPU about line card status
changes cannot be enabled / disabled on a per line card basis.
If a handler is registered before the line cards are initialized, the
handler risks accessing uninitialized memory.
On the other hand, if the handler is registered after initialization,
we risk missing events. For example, in step 4, the driver might see
that a line card is in ready state and will tell the device to enable
it. When enablement is done, the line card will be activated and the
IRQ will be triggered. Since a handler was not registered, the event
will be missed.
Solve this by splitting the initialization sequence into two steps
(1-2 and 3-4). In a subsequent patch, the handler will be registered
between both steps.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 451ef36bd229 ("ip_tunnels: Add new flow flags field to ip_tunnel_key")
added a "flow_flags" member to struct ip_tunnel_key which was later used by
the commit in the fixes tag to avoid dropping packets with sources that
aren't locally configured when set in bpf_set_tunnel_key().
VXLAN and GENEVE were made to respect this flag, ip tunnels like IPIP and GRE
were not.
This commit fixes this omission by making ip_tunnel_init_flow() receive
the flow flags from the tunnel key in the relevant collect_md paths.
Fixes: b8fff748521c ("bpf: Set flow flag to allow any source IP in bpf_tunnel_key")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Paul Chaignon <paul@isovalent.com>
Link: https://lore.kernel.org/bpf/20220818074118.726639-1-eyal.birger@gmail.com
|
|
This reverts commit 2dc2f760052da4925482ecdcdc5c94d4a599153c and
commit 6f73862fabd93213de157d9cc6ef76084311c628.
As discussed in the thread:
https://lore.kernel.org/all/f3c62ebe-7d59-c537-a010-bff366c8aeba@linaro.org/
the feature provided by commits 2dc2f760052da and 6f73862fabd93 is
actually already handled by the thermal framework via the cooling
device state aggregation, thus all this code is pointless.
The revert conflicts with the following changes:
- 7f4957be0d5b8: thermal: Use mode helpers in drivers
- 6a79507cfe94c: mlxsw: core: Extend thermal module with per QSFP module thermal zones
These conflicts were fixed and the resulting changes are in this patch.
Both reverts are in the same change as requested by Ido Schimmel:
https://lore.kernel.org/all/Yvz7+RUsmVco3Xpj@shredder/
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220817153040.2464245-1-daniel.lezcano@linaro.org
|
