| Age | Commit message (Collapse) | Author |
|---|
|
If the PTP_PEROUT_DUTY_CYCLE flag is set, then check if the
request_on value in ptp_perout_request matches the pre-defined
values or a toggle option.
Return a failure if the value is not supported.
Preserve the old behaviors if the PTP_PEROUT_DUTY_CYCLE flag is not
set.
Tested with an oscilloscope on EVB-LAN7430:
e.g., to output PPS 1sec period 500mS on (high) to GPIO 2.
./testptp -L 2,2
./testptp -p 1000000000 -w 500000000
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Link: https://lore.kernel.org/r/1634046593-64312-1-git-send-email-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in
other typical Linux drivers. The usage of phylib allows to
specify fixed-link parameters in the device tree.
. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).
Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing
as soon as the Corona measures allow this.
. All review findings of Andrew Lunn are included
Example:
--------
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of overlapping changes and parallel additions, stuff
like that.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 823eb2a3c4c7 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.
The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output
The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/microchip/lan743x_ptp.c:980:6: warning:
symbol 'lan743x_ptp_set_sync_ts_insert' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
timekeeping_clocktai64() has been renamed to ktime_get_clocktai_ts64()
for consistency with the other ktime_get_* access functions.
Rename the new caller that has come up as well.
Question: this is the only ptp driver that sets the hardware time
to the current system time in TAI. Why does it do that?
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building without CONFIG_PTP_1588_CLOCK results in multiple failures,
this was obviously not well tested:
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_isr':
drivers/net/ethernet/microchip/lan743x_ptp.c:781:28: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
ptp_schedule_worker(ptp->ptp_clock, 0);
^~~~~~~~~
tx_ts_lock
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_open':
drivers/net/ethernet/microchip/lan743x_ptp.c:879:6: error: unused variable 'ret' [-Werror=unused-variable]
int ret = -ENODEV;
^~~
At top level:
drivers/net/ethernet/microchip/lan743x_ptp.c:63:13: error: 'lan743x_ptp_tx_ts_enqueue_ts' defined but not used [-Werror=unused-function]
static void lan743x_ptp_tx_ts_enqueue_ts(struct lan743x_adapter *adapter,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
drivers/net/ethernet/microchip/lan743x_ethtool.c: In function 'lan743x_ethtool_get_ts_info':
drivers/net/ethernet/microchip/lan743x_ethtool.c:558:19: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
Those #ifdef checks are hard to get right, replace them all with
IS_ENABLED() checks that leave the same code visible to the compiler
but let it optimize out the unused bits based on the configuration.
Fixes: 07624df1c9ef ("lan743x: lan743x: Add PTP support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicated include.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP support includes:
Ingress, and egress timestamping.
One step timestamping available.
PTP clock support.
Periodic output support.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
