| Age | Commit message (Collapse) | Author |
|---|
|
During chip initialization, ports that use SGMII / QSGMII to interface to
external phys need to be configured on the VSC7513 and VSC7514. Expose this
configuration routine, so it can be used by DSA drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot-switch driver can utilize the phylink_mac_config routine. Move
this to the ocelot library location and export the symbol to make this
possible.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove ndo_get_devlink_port which is no longer used alongside with the
implementations in drivers.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Benefit from the previously implemented tracking of netdev events in
devlink code and instead of calling devlink_port_type_eth_set() and
devlink_port_type_clear() to set devlink port type and link to related
netdev, use SET_NETDEV_DEVLINK_PORT() macro to assign devlink_port
pointer to netdevice which is about to be registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move the logic from the ocelot switchdev driver's ocelot_get_stats64()
method to the common switch lib and reuse it for the DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_port_fdb_do_dump() is only used by ocelot_net.c, so move it
there.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if_link.h says:
* @rx_dropped: Number of packets received but not processed,
* e.g. due to lack of resources or unsupported protocol.
* For hardware interfaces this counter may include packets discarded
* due to L2 address filtering but should not include packets dropped
* by the device due to buffer exhaustion which are counted separately in
* @rx_missed_errors (since procfs folds those two counters together).
Currently we report "stats->rx_dropped = dev->stats.rx_dropped", the
latter being incremented by various entities in the stack. This is not
wrong, but we'd like to move ocelot_get_stats64() in the common ocelot
switch lib which is independent of struct net_device.
To do that, report the hardware RX drop counters instead. These drops
are due to policer action, or due to no destinations. When we have no
memory in the queue system, report this through rx_missed_errors, as
instructed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot->stats
Rather than reading the stats64 counters directly from the 32-bit
hardware, it's better to rely on the output produced by the periodic
ocelot_port_update_stats().
It would be even better to call ocelot_port_update_stats() right from
ocelot_get_stats64() to make sure we report the current values rather
than the ones from 2 seconds ago. But we need to export
ocelot_port_update_stats() from the switch lib towards the switchdev
driver for that, and future work will largely undo that.
There are more ocelot-based drivers waiting to be introduced, an example
of which is the SPI-controlled VSC7512. In that driver's case, it will
be impossible to call ocelot_port_update_stats() from ndo_get_stats64
context, since the latter is atomic, and reading the stats over SPI is
sleepable. So the compromise taken here, which will also hold going
forward, is to report 64-bit counters to stats64, which are not 100% up
to date.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 2 methods can run concurrently, and one will change the window of
counters (SYS_STAT_CFG_STAT_VIEW) that the other sees. The fix is
similar to what commit 7fbf6795d127 ("net: mscc: ocelot: fix mutex lock
error during ethtool stats read") has done for ethtool -S.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
align the extack argument of the ocelot_port_fdb_del()
function.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Link: https://lore.kernel.org/r/20220520002040.4442-1-eng.alaamohamedsoliman.am@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add extack support to .ndo_fdb_del in netdevice.h and
all related methods.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot switches perform port-based ingress mirroring if
ANA:PORT:PORT_CFG field SRC_MIRROR_ENA is set, and egress mirroring if
the port is in ANA:ANA:EMIRRORPORTS.
Both ingress-mirrored and egress-mirrored frames are copied to the port
mask from ANA:ANA:MIRRORPORTS.
So the choice of limiting to a single mirror port via ocelot_mirror_get()
and ocelot_mirror_put() may seem bizarre, but the hardware model doesn't
map very well to the user space model. If the user wants to mirror the
ingress of swp1 towards swp2 and the ingress of swp3 towards swp4, we'd
have to program ANA:ANA:MIRRORPORTS with BIT(2) | BIT(4), and that would
make swp1 be mirrored towards swp4 too, and swp3 towards swp2. But there
are no tc-matchall rules to describe those actions.
Now, we could offload a matchall rule with multiple mirred actions, one
per desired mirror port, and force the user to stick to the multi-action
rule format for subsequent matchall filters. But both DSA and ocelot
have the flow_offload_has_one_action() check for the matchall offload,
plus the fact that it will get cumbersome to cross-check matchall
mirrors with flower mirrors (which will be added in the next patch).
As a result, we limit the configuration to a single mirror port, with
the possibility of lifting the restriction in the future.
Frames injected from the CPU don't get egress-mirrored, since they are
sent with the BYPASS bit in the injection frame header, and this
bypasses the analyzer module (effectively also the mirroring logic).
I don't know what to do/say about this.
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress \
matchall skip_sw \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for adding port mirroring support to the ocelot driver,
the dispatching function ocelot_setup_tc_cls_matchall() must be free of
action-specific code. Move port policer creation and deletion to
separate functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the blamed commit, the call to the function
switchdev_bridge_port_offload was passing the wrong argument for
atomic_nb. It was ocelot_netdevice_nb instead of ocelot_swtchdev_nb.
This patch fixes this issue.
Fixes: 4e51bf44a03af6 ("net: bridge: move the switchdev object replay helpers to "push" mode")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to get mac from device-tree using of_get_ethdev_address.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethernet frames can be extracted or injected autonomously to or from
the device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list
data structures in memory are used for injecting or extracting Ethernet
frames. The FDMA generates interrupts when frame extraction or
injection is done and when the linked lists need updating.
The FDMA is shared between all the ethernet ports of the switch and
uses a linked list of descriptors (DCB) to inject and extract packets.
Before adding descriptors, the FDMA channels must be stopped. It would
be inefficient to do that each time a descriptor would be added so the
channels are restarted only once they stopped.
Both channels uses ring-like structure to feed the DCBs to the FDMA.
head and tail are never touched by hardware and are completely handled
by the driver. On top of that, page recycling has been added and is
mostly taken from gianfar driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Co-developed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit adds support for changing MTU for the ocelot register based
interface. For ocelot, JUMBO frame size can be set up to 25000 bytes
but has been set to 9000 which is a saner value and allows for maximum
gain of performance with FDMA.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ocelot_net has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the phy interface mode bitmap for the MSCC Ocelot driver with
the interface modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This converts instances of
bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS)
to
linkmode_foo(args...)
I manually fixed up some lines to prevent them from being excessively
long. Otherwise, this change was generated with the following semantic
patch:
// Generated with
// echo linux/linkmode.h > includes
// git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \
// | sort | uniq | tee new_includes | wc -l && mv new_includes includes
// and repeating until the number stopped going up
@i@
@@
(
#include <linux/acpi_mdio.h>
|
#include <linux/brcmphy.h>
|
#include <linux/dsa/loop.h>
|
#include <linux/dsa/sja1105.h>
|
#include <linux/ethtool.h>
|
#include <linux/ethtool_netlink.h>
|
#include <linux/fec.h>
|
#include <linux/fs_enet_pd.h>
|
#include <linux/fsl/enetc_mdio.h>
|
#include <linux/fwnode_mdio.h>
|
#include <linux/linkmode.h>
|
#include <linux/lsm_audit.h>
|
#include <linux/mdio-bitbang.h>
|
#include <linux/mdio.h>
|
#include <linux/mdio-mux.h>
|
#include <linux/mii.h>
|
#include <linux/mii_timestamper.h>
|
#include <linux/mlx5/accel.h>
|
#include <linux/mlx5/cq.h>
|
#include <linux/mlx5/device.h>
|
#include <linux/mlx5/driver.h>
|
#include <linux/mlx5/eswitch.h>
|
#include <linux/mlx5/fs.h>
|
#include <linux/mlx5/port.h>
|
#include <linux/mlx5/qp.h>
|
#include <linux/mlx5/rsc_dump.h>
|
#include <linux/mlx5/transobj.h>
|
#include <linux/mlx5/vport.h>
|
#include <linux/of_mdio.h>
|
#include <linux/of_net.h>
|
#include <linux/pcs-lynx.h>
|
#include <linux/pcs/pcs-xpcs.h>
|
#include <linux/phy.h>
|
#include <linux/phy_led_triggers.h>
|
#include <linux/phylink.h>
|
#include <linux/platform_data/bcmgenet.h>
|
#include <linux/platform_data/xilinx-ll-temac.h>
|
#include <linux/pxa168_eth.h>
|
#include <linux/qed/qed_eth_if.h>
|
#include <linux/qed/qed_fcoe_if.h>
|
#include <linux/qed/qed_if.h>
|
#include <linux/qed/qed_iov_if.h>
|
#include <linux/qed/qed_iscsi_if.h>
|
#include <linux/qed/qed_ll2_if.h>
|
#include <linux/qed/qed_nvmetcp_if.h>
|
#include <linux/qed/qed_rdma_if.h>
|
#include <linux/sfp.h>
|
#include <linux/sh_eth.h>
|
#include <linux/smsc911x.h>
|
#include <linux/soc/nxp/lpc32xx-misc.h>
|
#include <linux/stmmac.h>
|
#include <linux/sunrpc/svc_rdma.h>
|
#include <linux/sxgbe_platform.h>
|
#include <net/cfg80211.h>
|
#include <net/dsa.h>
|
#include <net/mac80211.h>
|
#include <net/selftests.h>
|
#include <rdma/ib_addr.h>
|
#include <rdma/ib_cache.h>
|
#include <rdma/ib_cm.h>
|
#include <rdma/ib_hdrs.h>
|
#include <rdma/ib_mad.h>
|
#include <rdma/ib_marshall.h>
|
#include <rdma/ib_pack.h>
|
#include <rdma/ib_pma.h>
|
#include <rdma/ib_sa.h>
|
#include <rdma/ib_smi.h>
|
#include <rdma/ib_umem.h>
|
#include <rdma/ib_umem_odp.h>
|
#include <rdma/ib_verbs.h>
|
#include <rdma/iw_cm.h>
|
#include <rdma/mr_pool.h>
|
#include <rdma/opa_addr.h>
|
#include <rdma/opa_port_info.h>
|
#include <rdma/opa_smi.h>
|
#include <rdma/opa_vnic.h>
|
#include <rdma/rdma_cm.h>
|
#include <rdma/rdma_cm_ib.h>
|
#include <rdma/rdmavt_cq.h>
|
#include <rdma/rdma_vt.h>
|
#include <rdma/rdmavt_qp.h>
|
#include <rdma/rw.h>
|
#include <rdma/tid_rdma_defs.h>
|
#include <rdma/uverbs_ioctl.h>
|
#include <rdma/uverbs_named_ioctl.h>
|
#include <rdma/uverbs_std_types.h>
|
#include <rdma/uverbs_types.h>
|
#include <soc/mscc/ocelot.h>
|
#include <soc/mscc/ocelot_ptp.h>
|
#include <soc/mscc/ocelot_vcap.h>
|
#include <trace/events/ib_mad.h>
|
#include <trace/events/rdma_core.h>
|
#include <trace/events/rdma.h>
|
#include <trace/events/rpcrdma.h>
|
#include <uapi/linux/ethtool.h>
|
#include <uapi/linux/ethtool_netlink.h>
|
#include <uapi/linux/mdio.h>
|
#include <uapi/linux/mii.h>
)
@depends on i@
expression list args;
@@
(
- bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_zero(args)
|
- bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_copy(args)
|
- bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_and(args)
|
- bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_or(args)
|
- bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_empty(args)
|
- bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_andnot(args)
|
- bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_equal(args)
|
- bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_intersects(args)
|
- bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_subset(args)
)
Add missing linux/mii.h include to mellanox. -DaveM
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot switchdev driver does not include the CPU port in the list of
flooding destinations for unknown traffic, instead that traffic is
supposed to match FDB entries to reach the CPU.
The addresses it installs are:
(a) the station MAC address, in ocelot_probe_port() and later during
runtime in ocelot_port_set_mac_address(). These are the VLAN-unaware
addresses. The VLAN-aware addresses are in ocelot_vlan_vid_add().
(b) multicast addresses added with dev_mc_add() (not bridge host MDB
entries) in ocelot_mc_sync()
(c) multicast destination MAC addresses for MRP in ocelot_mrp_save_mac(),
to make sure those are dropped (not forwarded) by the bridging
service, just trapped to the CPU
So we can see that the logic is slightly buggy ever since the initial
commit a556c76adc05 ("net: mscc: Add initial Ocelot switch support").
This is because, when ocelot_probe_port() runs, the port pvid is 0.
Then we join a VLAN-aware bridge, the pvid becomes 1, we call
ocelot_port_set_mac_address(), this learns the new MAC address in VID 1
(also fails to forget the old one, since it thinks it's in VID 1, but
that's not so important). Then when we leave the VLAN-aware bridge,
outside world is unable to ping our new MAC address because it isn't
learned in VID 0, the VLAN-unaware pvid.
[ note: this is strictly based on static analysis, I don't have hardware
to test. But there are also many more corner cases ]
The basic idea is that we should have a separation of concerns, and the
FDB entries used for standalone operation should be managed by the
driver, and the FDB entries used by the bridging service should be
managed by the bridge. So the standalone and VLAN-unaware bridge FDB
entries should not follow the bridge PVID, because that will only be
active when the bridge is VLAN-aware. So since the port pvid is
coincidentally zero during probe time, just make those entries
statically go to VID 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5fe ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b3250 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following coccicheck warning:
drivers/net/ethernet/mscc/ocelot.c:474:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot.c:476:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot_net.c:1627:duplicated argument
to & or |
These DEV_CLOCK_CFG_MAC_TX_RST are duplicate here.
Here should be DEV_CLOCK_CFG_MAC_RX_RST.
Fixes: e6e12df625f2 ("net: mscc: ocelot: convert to phylink")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to transmit more restrictions in future patches, convert this
one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are cases where we would like to continue probing the switch even
if one port has failed to probe. When that happens, we need to
unregister a devlink_port of type DEVLINK_PORT_FLAVOUR_PHYSICAL and
re-register it of type DEVLINK_PORT_FLAVOUR_UNUSED.
This is fine, except when calling devlink_port_attrs_set on a structure
on which devlink_port_register has been previously called, there is a
WARN_ON in devlink_port_attrs_set that devlink_port->devlink must be
NULL.
So don't assume that the memory behind dlp is clean when calling
ocelot_port_devlink_init, just zero-initialize it.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:
- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
which are written with their hardware default values, also runtime
invariants. So it makes no sense to write these during every .ndo_open.
- PORTID_VAL: this field has an out-of-reset value of zero for all ports
and must be initialized by software. Additionally, the
ocelot_setup_logical_port_ids() code path sets up different logical
port IDs for the ports in a hardware LAG, and we absolutely don't want
.ndo_open to interfere there and reset those values.
So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.
ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.
So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The point with a *dev and a *brport_dev is that when we have a LAG net
device that is a bridge port, *dev is an ocelot net device and
*brport_dev is the bonding/team net device. The ocelot net device
beneath the LAG does not exist from the bridge's perspective, so we need
to sync the switchdev objects belonging to the brport_dev and not to the
dev.
Fixes: e4bd44e89dcf ("net: ocelot: replay switchdev events when joining bridge")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a switchdev port leaves a LAG that is a bridge port, the switchdev
objects and port attributes offloaded to that port are not removed:
ip link add br0 type bridge
ip link add bond0 type bond mode 802.3ad
ip link set swp0 master bond0
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 nomaster
VLAN 100 will remain installed on swp0 despite it going into standalone
mode, because as far as the bridge is concerned, nothing ever happened
to its bridge port.
Let's extend the bridge vlan, fdb and mdb replay functions to take a
'bool adding' argument, and make DSA and ocelot call the replay
functions with 'adding' as false from the switchdev unsync path, for the
switch port that leaves the bridge.
Note that this patch in itself does not salvage anything, because in the
current pull mode of operation, DSA still needs to call the replay
helpers with adding=false. This will be done in another patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a slight inconvenience in the switchdev replay helpers added
recently, and this is when:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 master bond0
ip link set swp1 master bond0
Since the underlying driver (currently only DSA) asks for a replay of
VLANs when swp0 and swp1 join the LAG because it is bridged, what will
happen is that DSA will try to react twice on the VLAN event for swp0.
This is not really a huge problem right now, because most drivers accept
duplicates since the bridge itself does, but it will become a problem
when we add support for replaying switchdev object deletions.
Let's fix this by adding a blank void *ctx in the replay helpers, which
will be passed on by the bridge in the switchdev notifications. If the
context is NULL, everything is the same as before. But if the context is
populated with a valid pointer, the underlying switchdev driver
(currently DSA) can use the pointer to 'see through' the bridge port
(which in the example above is bond0) and 'know' that the event is only
for a particular physical port offloading that bridge port, and not for
all of them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case where the driver asks for a replay of a certain type of
event (port object or attribute) for a bridge port that is a LAG, it may
do so because this port has just joined the LAG.
But there might already be other switchdev ports in that LAG, and it is
preferable that those preexisting switchdev ports do not act upon the
replayed event.
The solution is to add a context to switchdev events, which is NULL most
of the time (when the bridge layer initiates the call) but which can be
set to a value controlled by the switchdev driver when a replay is
requested. The driver can then check the context to figure out if all
ports within the LAG should act upon the switchdev event, or just the
ones that match the context.
We have to modify all switchdev_handle_* helper functions as well as the
prototypes in the drivers that use these helpers too, because these
helpers hide the underlying struct switchdev_notifier_info from us and
there is no way to retrieve the context otherwise.
The context structure will be populated and used in later patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not using this driver, I did not realize it doesn't react to
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE notifications, but it implements just
the bridge bypass operations (.ndo_fdb_{add,del}). So the call to
br_fdb_replay just produces notifications that are ignored, delete it
for now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
