| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
|
|
In nfp_flower_spawn_vnic_reprs in the loop if initialization or the
allocations fail memory is leaked. Appropriate releases are added.
Fixes: b94524529741 ("nfp: flower: add per repr private data for LAG offload")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In nfp_flower_spawn_phy_reprs, in the for loop over eth_tbl if any of
intermediate allocations or initializations fail memory is leaked.
requiered releases are added.
Fixes: b94524529741 ("nfp: flower: add per repr private data for LAG offload")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build in
unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
* tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (63 commits)
genksyms: convert to SPDX License Identifier for lex.l and parse.y
modpost: use __section in the output to *.mod.c
modpost: use MODULE_INFO() for __module_depends
export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols
export.h: remove defined(__KERNEL__), which is no longer needed
kbuild: allow Clang to find unused static inline functions for W=1 build
kbuild: rename KBUILD_ENABLE_EXTRA_GCC_CHECKS to KBUILD_EXTRA_WARN
kbuild: refactor scripts/Makefile.extrawarn
merge_config.sh: ignore unwanted grep errors
kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)
modpost: add NOFAIL to strndup
modpost: add guid_t type definition
kbuild: add $(BASH) to run scripts with bash-extension
kbuild: remove ARCH_{CPP,A,C}FLAGS
kbuild,arc: add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3 for ARC
kbuild: Do not enable -Wimplicit-fallthrough for clang for now
kbuild: clean up subdir-ymn calculation in Makefile.clean
kbuild: remove unneeded '+' marker from cmd_clean
kbuild: remove clean-dirs syntax
kbuild: check clean srctree even earlier
...
|
|
Minor overlapping changes in the btusb and ixgbe drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flower control message replies are handled in different locations. The truly
high priority replies are handled in the BH (tasklet) context, while the
remaining replies are handled in a predefined Linux work queue. The work
queue handler orders replies into high and low priority groups, and always
start servicing the high priority replies within the received batch first.
Reply Type: Rtnl Lock: Handler:
CMSG_TYPE_PORT_MOD no BH tasklet (mtu)
CMSG_TYPE_TUN_NEIGH no BH tasklet
CMSG_TYPE_FLOW_STATS no BH tasklet
CMSG_TYPE_PORT_REIFY no WQ high
CMSG_TYPE_PORT_MOD yes WQ high (link/mtu)
CMSG_TYPE_MERGE_HINT yes WQ low
CMSG_TYPE_NO_NEIGH no WQ low
CMSG_TYPE_ACTIVE_TUNS no WQ low
CMSG_TYPE_QOS_STATS no WQ low
CMSG_TYPE_LAG_CONFIG no WQ low
A subset of control messages can block waiting for an rtnl lock (from both
work queue priority groups). The rtnl lock is heavily contended for by
external processes such as systemd-udevd, systemd-network and libvirtd,
especially during netdev creation, such as when flower VFs and representors
are instantiated.
Kernel netlink instrumentation shows that external processes (such as
systemd-udevd) often use successive rtnl_trylock() sequences, which can result
in an rtnl_lock() blocked control message to starve for longer periods of time
during rtnl lock contention, i.e. netdev creation.
In the current design a single blocked control message will block the entire
work queue (both priorities), and introduce a latency which is
nondeterministic and dependent on system wide rtnl lock usage.
In some extreme cases, one blocked control message at exactly the wrong time,
just before the maximum number of VFs are instantiated, can block the work
queue for long enough to prevent VF representor REIFY replies from getting
handled in time for the 40ms timeout.
The firmware will deliver the total maximum number of REIFY message replies in
around 300us.
Only REIFY and MTU update messages require replies within a timeout period (of
40ms). The MTU-only updates are already done directly in the BH (tasklet)
handler.
Move the REIFY handler down into the BH (tasklet) in order to resolve timeouts
caused by a blocked work queue waiting on rtnl locks.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent code changes to NFP allowed the offload of neighbour entries to FW
when the next hop device was an internal port. This allows for offload of
tunnel encap when the end-point IP address is applied to such a port.
Unfortunately, the neighbour event handler still rejects events that are
not associated with a repr dev and so the firmware neighbour table may get
out of sync for internal ports.
Fix this by allowing internal port neighbour events to be correctly
processed.
Fixes: 45756dfedab5 ("nfp: flower: allow tunnels to output to internal port")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal port TC offload is implemented through user-space applications
(such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect
block offload support in the NFP driver accepts both ingress qdisc binds
and egress binds if the device is an internal port. However, clsact sends
bind notification for both ingress and egress block binds which can lead
to the driver registering multiple callbacks and receiving multiple
notifications of new filters.
Fix this by rejecting ingress block bind callbacks when the port is
internal and only adding filter callbacks for egress binds.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor conflict in r8169, bug fix had two versions in net
and net-next, take the net-next hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the single target build descends into sub-directories in the
same way as the normal build, these dummy Makefiles are not needed
any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When processing FLOW_BLOCK_BIND command on indirect block, check that flow
block cb is not busy.
Fixes: 0d4fd02e7199 ("net: flow_offload: add flow_block_cb_is_busy() and use it")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge conflict of mlx5 resolved using instructions in merge
commit 9566e650bf7fdf58384bb06df634f7531ca3a97e.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc transparently maps the software priority number to hardware. Update
it to pass the major priority which is what most drivers expect. Update
drivers too so they do not need to lshift the priority field of the
flow_cls_common_offload object. The stmmac driver is an exception, since
this code assumes the tc software priority is fine, therefore, lshift it
just to be conservative.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
move tc indirect block to flow_offload and rename
it to flow indirect block.The nf_tables can use the
indr block architecture.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a tunnel packet arrives on the NFP card, its destination MAC is
looked up and MAC index returned for it. This index can help verify the
tunnel by, for example, ensuring that the packet arrived on the expected
port. If the packet is destined for a known MAC that is not connected to a
given physical port then the mac index can have a global value (e.g. when
a series of bonded ports shared the same MAC).
If the packet is to be detunneled at a bridge device or internal port like
an Open vSwitch VLAN port, then it should first match a 'pre-tunnel' rule
to direct it to that internal port.
Use the MAC index to indicate if a packet should match a pre-tunnel rule
before decap is allowed. Do this by tracking the number of internal ports
associated with a MAC address and, if the number if >0, set a bit in the
mac_index to forward the packet to the pre-tunnel table before continuing
with decap.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAC addresses along with an identifying index are offloaded to firmware to
allow tunnel decapsulation. If a tunnel packet arrives with a matching
destination MAC address and a verified index, it can continue on the
decapsulation process. This replicates the MAC verifications carried out
in the kernel network stack.
When a netdev is added to a bridge (e.g. OvS) then packets arriving on
that dev are directed through the bridge datapath instead of passing
through the network stack. Therefore, tunnelled packets matching the MAC
of that dev will not be decapped here.
Replicate this behaviour on firmware by removing offloaded MAC addresses
when a MAC representer is added to an OvS bridge. This can prevent any
false positive tunnel decaps.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-tunnel rules are TC flower and OvS rules that forward a packet to the
tunnel end point where it can then pass through the network stack and be
decapsulated. These are required if the tunnel end point is, say, an OvS
internal port.
Currently, firmware determines that a packet is in a tunnel and decaps it
if it has a known destination IP and MAC address. However, this bypasses
the flower pre-tunnel rule and so does not update the stats. Further to
this it ignores VLANs that may exist outside of the tunnel header.
Offload pre-tunnel rules to the NFP. This embeds the pre-tunnel rule into
the tunnel decap process based on (firmware) mac index and VLAN. This
means that decap can be carried out correctly with VLANs and that stats
can be updated for all kernel rules correctly.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-tunnel rules must direct packets to an internal port based on L2
information. Rules that egress to an internal port are already indicated
by a non-NULL device in its nfp_fl_payload struct. Verfiy the rest of the
match fields indicate that the rule is a pre-tunnel rule. This requires a
full match on the destination MAC address, an option VLAN field, and no
specific matches on other lower layer fields (with the exception of L4
proto and flags).
If a rule is identified as a pre-tunnel rule then mark it for offload to
the pre-tunnel table. Similarly, remove it from the pre-tunnel table on
rule deletion. The actual offloading of these commands is left to a
following patch.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-tunnel rules are used when the tunnel end-point is on an 'internal
port'. These rules are used to direct the tunnelled packets (based on outer
header fields) to the internal port where they can be detunnelled. The
rule must send the packet to ingress the internal port at the TC layer.
Currently FW does not support an action to send to ingress so cannot
offload such rules. However, in preparation for populating the pre-tunnel
table to represent such rules, check for rules that send to the ingress of
an internal port and mark them as such. Further validation of such rules
is left to subsequent patches.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP allows the merging of 2 flows together into a single offloaded flow.
In the kernel datapath the packet must match 1 flow, impliment its
actions, recirculate, match the 2nd flow and also impliment its actions.
Merging creates a single flow with all actions from the 2 original flows.
Firmware impliments a tunnel header push as the packet is about to egress
the card. Therefore, if the first merge rule candiate pushes a tunnel,
then the second rule can only have an egress action for a valid merge to
occur (or else the action ordering will be incorrect). This prevents the
pushing of a tunnel header followed by the pushing of a vlan header.
In order to support this behaviour, firmware allows VLAN information to
be encoded in the tunnel push action. If this is non zero then the fw will
push a VLAN after the tunnel header push meaning that 2 such flows with
these actions can be merged (with action order being maintained).
Support tunnel in VLAN pushes by encoding VLAN information in the tunnel
push action of any merge flow requiring this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS set actions to
firmware. Set actions update the outermost MPLS header. The offload
includes a mask to specify which fields should be set.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS pop actions to
firmware. The act_mpls TC module enforces that the next protocol is
supplied along with the pop action. Passing this to firmware allows it
to properly rebuild the underlying packet after the pop.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS push actions to
firmware.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904ff4 ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c8537 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flower rules on the NFP firmware are able to match on an IP protocol
field. When parsing rules in the driver, unknown IP protocols are only
rejected when further matches are to be carried out on layer 4 fields, as
the firmware will not be able to extract such fields from packets.
L4 protocol dissectors such as FLOW_DISSECTOR_KEY_PORTS are only parsed if
an IP protocol is specified. This leaves a loophole whereby a rule that
attempts to match on transport layer information such as port numbers but
does not explicitly give an IP protocol type can be incorrectly offloaded
(in this case with wildcard port numbers matches).
Fix this by rejecting the offload of flows that attempt to match on L4
information, not only when matching on an unknown IP protocol type, but
also when the protocol is wildcarded.
Fixes: 2a04784594f6 ("nfp: flower: check L4 matches on unknown IP protocols")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP firmware does not explicitly match on an ethernet type field. Rather,
each rule has a bitmask of match fields that can be used to infer the
ethernet type.
Currently, if a flower rule contains an unknown ethernet type, a check is
carried out for matches on other fields of the packet. If matches on
layer 3 or 4 are found, then the offload is rejected as firmware will not
be able to extract these fields from a packet with an ethernet type it
does not currently understand.
However, if a rule contains an unknown ethernet type without any L3 (or
above) matches then this will effectively be offloaded as a rule with a
wildcarded ethertype. This can lead to misclassifications on the firmware.
Fix this issue by rejecting all flower rules that specify a match on an
unknown ethernet type.
Further ensure correct offloads by moving the 'L3 and above' check to any
rule that does not specify an ethernet type and rejecting rules with
further matches. This means that we can still offload rules with a
wildcarded ethertype if they only match on L2 fields but will prevent
rules which match on further fields that we cannot be sure if the firmware
will be able to extract.
Fixes: af9d842c1354 ("nfp: extend flower add flow offload")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new GRE encapsulation support, which allows offload of filters
using tunnel_key set action in combination with actions that egress
to GRE type ports.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the existing tunnel matching support to include GRE decap
classification. Specifically matching existing tunnel fields for
NVGRE (GRE with protocol field set to TEB).
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously tunnel related functions in action offload only applied
to UDP tunnels. Rename these functions in preparation for new
tunnel types.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds IPv4 address and TTL/TOS helper functions, which is done in
preparation for compiling new tunnel types.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the key layer calculation function, in particular the tunnel
key layer calculation by introducing helper functions. This is done
in preparation for supporting GRE tunnel offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use extack messages in flower offload when compiling match and actions
messages that will configure hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use extack messages in flower offload, specifically focusing on
the extack use in add offload, remove offload and get stats paths.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matching on fields with a protocol that is unknown to hardware
is not strictly unsupported. Determine if hardware can offload
a filter with an unknown protocol by checking if any L4 fields
are being matched as well.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct nfp_tun_active_tuns {
...
struct route_ip_info {
__be32 ipv4;
__be32 egress_port;
__be32 extra[2];
} tun_info[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(struct nfp_tun_active_tuns) + sizeof(struct route_ip_info) * count
with:
struct_size(payload, tun_info, count)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add rcu locks when accessing netdev when processing route request
and tunnel keep alive messages received from hardware.
Fixes: 8e6a9046b66a ("nfp: flower vxlan neighbour offload")
Fixes: 856f5b135758 ("nfp: flower vxlan neighbour keep-alive")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on feedback from Jiri avoid carrying a pointer to the tcf_block
structure in the tc_cls_common_offload structure. Instead store
a flag in driver private data which indicates if offloads apply
to a shared block at block binding time.
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add stats request function that sends a stats request message to hw for
a specific police-filter. Process stats reply from hw and update the
stored qos structure.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add install and remove offload functionality for qos offloads. We
first check that a police filter can be implemented by the VF rate
limiting feature in hw, then we install the filter via the qos
infrastructure. Finally we implement the mechanism for removing
these types of filters.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce matchall filter offload infrastructure that is needed to
offload qos features like policing. Subsequent patches will make
use of police-filters for ingress rate limiting.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent addition to NFP introduced a function that formats a string with
a size_t variable. This is formatted with %ld which is fine on 64-bit
architectures but produces a compile warning on 32-bit architectures.
Fix this by using the z length modifier.
Fixes: a6156a6ab0f9 ("nfp: flower: handle merge hint messages")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nfp_flower_copy_pre_actions function introduces a case statement with
an intentional fallthrough. However, this generates a warning if built
with the -Wimplicit-fallthrough flag.
Remove the warning by adding a fall through comment.
Fixes: 1c6952ca587d ("nfp: flower: generate merge flow rule")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A merge flow is formed from 2 sub flows. The match fields of the merge are
the same as the first sub flow that has formed it, with the actions being
a combination of the first and second sub flow. Therefore, a merge flow
should replace sub flow 1 when offloaded.
Offload valid merge flows by using a new 'flow mod' message type to
replace an existing offloaded rule. Track the deletion of sub flows that
are linked to a merge flow and revert offloaded merge rules if required.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
