| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This will be useful for shortcutting some software packet parsing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
PCI legacy interrupts are level-triggered, and we cannot mask them up
on an isolated device. Instead, disable the IRQ at the controller
until we have recovered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We should not use net_device::dev_id to indicate the port number, as
this affects the way the local part of IPv6 addresses is normally
generated.
This field was intended for use where multiple devices may share a
single assigned MAC address and need to have different IPv6 addresses.
Siena's two ports each have their own MAC addresses.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
efx_start_datapath() asserts that we can fit 2 RX scatter buffers plus
a software structure, each appropriately aligned, into a single page.
Where L1_CACHE_BYTES == 256 and PAGE_SIZE == 4096, which is the case
on s390, this assertion fails.
The current scatter buffer size is also not a multiple of 64 or 128,
which are more common cache line sizes. If we can make both the start
and end of a scatter buffer cache-aligned, this will reduce the need
for read-modify-write operations on inter- processor links.
Fix the alignment by reducing EFX_RX_USR_BUF_SIZE to 2048 - 256 ==
1792. (We could use 2048 - L1_CACHE_BYTES, but EFX_RX_USR_BUF_SIZE
also affects user-level networking where a larger amount of
housekeeping data may be needed. Although this version of the driver
does not support user-level networking, I prefer to keep scattering
behaviour consistent with the out-of-tree version.)
This still doesn't fix the s390 build because like most architectures
it has NET_IP_ALIGN == 2. When NET_IP_ALIGN != 0 we cannot achieve
cache line alignment at either the start or end of a scatter buffer,
so there is actually no point in padding the buffers to a multiple of
the cache line size. All we need is 4-byte alignment of the network
header, so do that.
Adjust the assertions accordingly.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The two architectures that define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
(powerpc and x86) now both define NET_IP_ALIGN as 0, so there is no
need for this optimisation any more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocating 2 buffers per page is insanely inefficient when MTU is 1500
and PAGE_SIZE is 64K (as it usually is on POWER). Allocate as many as
we can fit, and choose the refill batch size at run-time so that we
still always use a whole page at once.
[bwh: Fix loop condition to allow for compound pages; rebase]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This condition is brittle and we have lots of flags to spare.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
On POWER systems, DMA mapping/unmapping operations are very expensive.
These changes reduce these costs by trying to reuse DMA mapped pages.
After all the buffers associated with a page have been processed and
passed up, the page is placed into a ring (if there is room). For
each page that is required for a refill operation, a page in the ring
is examined to determine if its page count has fallen to 1, ie. the
kernel has released its reference to these packets. If this is the
case, the page can be immediately added back into the RX descriptor
ring, without having to re-map it for DMA.
If the kernel is still holding a reference to this page, it is removed
from the ring and unmapped for DMA. Then a new page, which can
immediately be used by RX buffers in the descriptor ring, is allocated
and DMA mapped.
The time a page needs to spend in the recycle ring before the kernel
has released its page references is based on the number of buffers
that use this page. As large pages can hold more RX buffers, the RX
recycle ring can be shorter. This reduces memory usage on POWER
systems, while maintaining the performance gain achieved by recycling
pages, following the driver change to pack more than two RX buffers
into large pages.
When an IOMMU is not present, the recycle ring can be small to reduce
memory usage, since DMA mapping operations are inexpensive.
With a small recycle ring, attempting to refill the descriptor queue
with more buffers than the equivalent size of the recycle ring could
ultimately lead to memory leaks if page entries in the recycle ring
were overwritten. To prevent this, the check to see if the recycle
ring is full is changed to check if the next entry to be written is
NULL.
[bwh: Combine and rebase several commits so this is complete
before the following buffer-packing changes. Remove module
parameter.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Enable RX DMA scattering iff an RX buffer large enough for the current
MTU will not fit into a single page and the NIC supports DMA
scattering for kernel-mode RX queues.
On Falcon and Siena, the RX_USR_BUF_SIZE field is used as the DMA
limit for both all RX queues with scatter enabled. Set it to 1824,
matching what Onload uses now.
Maintain a statistic for frames truncated due to lack of descriptors
(rx_nodesc_trunc). This is distinct from rx_frm_trunc which may be
incremented when scattering is disabled and implies an over-length
frame.
Whenever an MTU change causes scattering to be turned on or off,
update filters that point to the PF queues, but leave others
unchanged, as VF drivers assume scattering is off.
Add n_frags parameters to various functions, and make them iterate:
- efx_rx_packet()
- efx_recycle_rx_buffers()
- efx_rx_mk_skb()
- efx_rx_deliver()
Make efx_handle_rx_event() responsible for updating
efx_rx_queue::removed_count.
Change the RX pipeline state to a starting ring index and number of
fragments, and make __efx_rx_packet() responsible for clearing it.
Based on earlier versions by David Riddoch and Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Adjust rx_buf->page_offset when we eat the RX hash prefix. Remove
efx_rx_buf_offset(), which is now redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Replace efx_nic::rx_buffer_len with efx_nic::rx_dma_len, the maximum
RX DMA length.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The Linux side of EEH is triggered by MMIO reads, but this
driver's data path does not issue any MMIO reads (except in
legacy interrupt mode). Therefore add a monitor function
to poll EEH periodically.
When preparing to reset the device based on our own error
detection, also poll EEH and defer to its recovery mechanism
if appropriate.
[bwh: Use a separate condition for the initial link poll; fix some
style errors]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
[bwh: Remove more dead code, and make efx_ptp_rx() pull the data it
needs into the header area.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Instead of having efx_ptp_rx() call netif_receive_skb() for an invalid
PTP packet, make it return false for rejected packets and have
efx_rx_deliver() pass them up.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.
[bwh: Minor fixes to coding style]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Receiving pause frames can block TX queue flushes. Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:
- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
as part of net driver modules. (This also fixes cases where the PTP
subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
drivers but are built separately
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are now standard functions for dealing with little-endian bit
arrays, so use them instead of our own implementations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The key new feature for 3.2 is PTP support.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Allows an extra channel to override the standard receive_skb handler
and also for extra non generic operations to be performed on remove.
Also set default rx strategy so only skbs can be delivered to the
PTP receive function.
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The PTP channel will have its own RX queue even though it's not
a regular traffic channel.
Original work by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
STATE_INIT and STATE_FINI are equivalent and represent incompletely
initialised states; combine them as STATE_UNINIT.
Rename STATE_RUNNING to STATE_READY, to avoid confusion with
netif_running() and IFF_RUNNING.
The comments do not quite match current usage, but this will be
corrected in subsequent fixes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
TSO header buffers contain a control structure immediately followed by
the packet headers, and are kept on a free list when not in use. This
complicates buffer management and tends to result in cache read misses
when we recycle such buffers (particularly if DMA-coherent memory
requires caches to be disabled).
Replace the free list with a simple mapping by descriptor index. We
know that there is always a payload descriptor between any two
descriptors with TSO header buffers, so we can allocate only one
such buffer for each two descriptors.
While we're at it, use a standard error code for allocation failure,
not -1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We now have a definite upper bound on the number of descriptors per
skb; use that to stop the queue when the next packet might not fit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add a flags field to struct efx_tx_buffer, replacing the
continuation and map_single booleans.
Since a single descriptor cannot be both a TSO header and the last
descriptor for an skb, unionise efx_tx_buffer::{skb,tsoh} and add
flags for validity of these fields.
Clear all flags in free buffers (whereas previously the continuation
flag would be set).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. Fix potential badness when running a self-test with SR-IOV enabled.
2. Fix calculation of some interface statistics that could run backward.
3. Miscellaneous cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.
On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again. So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.
In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting. Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently allows for SFP+ eeprom to be returned using the ethtool API.
This can be extended in future to handle different eeprom formats
and sizes
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh: Drop redundant validation, comment, whitespace]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
There was no runtime control of the fast_fill_limit in any case, so purged
that field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This member has never been used in a production version of the driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
efx_for_each_possible_channel_tx_queue() should do nothing for RX-only
or extra channels. The current definition results in allocating
additional unused hardware TX queues when using the mqprio qdisc and
either separate_tx_channels or SR-IOV.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Each port has a block of 64-bit SRAM that is divided between buffer
table and descriptor cache regions at initialisation time. Currently
we use a fixed allocation, but it needs to be changed to support
larger numbers of queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Abstract some of the channel operations to allow for 'extra'
channels that do not have RX or TX queues.
- Try to assign a channel to each extra channel type that is enabled
for the NIC, but gracefully degrade if we can't allocate sufficient
MSI-X vectors
- Allow each extra channel type to generate its own channel name
- Allow channel types to disable reallocation and reinitialisation
of their channels
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The TX DMA engine issues upstream read requests when there is room in
the TX FIFO for the completion. However, the fetches for the rest of
the packet might be delayed by any back pressure. Since a flush must
wait for an EOP, the entire flush may be delayed by back pressure.
Mitigate this by disabling flow control before the flushes are
started. Since PF and VF flushes run in parallel introduce
fc_disable, a reference count of the number of flushes outstanding.
The same principle could be applied to Falcon, but that
would bring with it its own testing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
When SR-IOV is enabled we may receive FLR (Function-Level Reset)
events, associated queue flush events and requests from VF drivers at
any time. Therefore we need to keep event queues and interrupts
enabled whenever possible.
Currently we stop interrupt-driven event processing before flushing RX
and TX queues; efx_nic_flush_queues() then polls event queues for
flush events and discards any others it finds. Change it to work with
the regular event handling functions.
Currently efx_start_channel() fills RX queues synchronously when a
device is brought up. This could now race with NAPI, so change it to
send fill events.
This was almost entirely written by Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Replace checksummed and discard booleans from efx_handle_rx_event()
with a bitmask, added to the flags field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Currently we use type u64 for byte counts, which can very quickly
exceed 2^32, and unsigned long for packet counts, which do not. But
it can still take only 20-something minutes to send or receive 2^32
packets, and not all tools properly handle overflow even if they
sample more often than this.
The MAC statistics are all updated synchronously, so it costs very
little to make them all 64-bit regardless of native word size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Interrupts are normally generated by the event queues, moderated by
timers. However, they may also be triggered by detection of a 'fatal'
error condition (e.g. memory parity error) or by the host writing to
certain CSR fields as part of a self-test.
The IRQ level/index used for these on Falcon rev B0 and Siena is set
by the KER_INT_LEVE_SEL field and cached by the driver in
efx_nic::fatal_irq_level. Since this value is also relevant to
self-tests rename the field to just 'irq_level'.
Avoid unnecessary cache traffic by using a per-channel 'last_irq_cpu'
field and only writing to the per-controller field when the interrupt
matches efx_nic::irq_level. Remove the volatile qualifier and use
ACCESS_ONCE in the places we read these fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
