| Age | Commit message (Collapse) | Author |
|---|
|
Revert "net: stmmac: Use interrupt mode INTM=1 for per channel irq"
This reverts commit 36af9f25ddfd311da82628f194c794786467cb12.
Revert "net: stmmac: Add support for TX/RX channel interrupt"
This reverts commit 9072e03d32088137a435ddf3aa95fd6e038d69d8.
Revert "net: stmmac: Make MSI interrupt routine generic"
This reverts commit 477bd4beb93bf9ace9bda71f1437b191befa9cf4.
Revert "dt-bindings: net: snps,dwmac: per channel irq"
This reverts commit 67d47c8ada0f8795bfcdb85cc8f2ad3ce556674b.
Device tree bindings need to be reviewed.
Link: https://lore.kernel.org/all/2df9fe3e-7971-4aa2-89a9-0e085b3b00d7@linaro.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable TX/RX channel interrupt registration for MAC that interrupts CPU
through shared peripheral interrupt (SPI).
Per channel interrupts and interrupt-names are registered through,
Eg: 4 tx and 4 rx channels:
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "dma_tx0",
"dma_tx1",
"dma_tx2",
"dma_tx3",
"dma_rx0",
"dma_rx1",
"dma_rx2",
"dma_rx3";
Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently a MDIO bus is created if the devicetree description is either:
1. Not fixed-link
2. fixed-link but contains a MDIO bus as well
The "1" case above isn't always accurate. If there's a phy-handle,
it could be referencing a phy on another MDIO controller's bus[1]. In
this case, where the MDIO bus is not described at all, currently
stmmac will make a MDIO bus and scan its address space to discover
phys (of which there are none). This process takes time scanning a bus
that is known to be empty, delaying time to complete probe.
There are also a lot of upstream devicetrees[2] that expect a MDIO bus
to be created, scanned for phys, and the first one found connected
to the MAC. This case can be inferred from the platform description by
not having a phy-handle && not being fixed-link. This hits case "1" in
the current driver's logic, and must be handled in any logic change here
since it is a valid legacy dt-binding.
Let's improve the logic to create a MDIO bus if either:
- Devicetree contains a MDIO bus
- !fixed-link && !phy-handle (legacy handling)
This way the case where no MDIO bus should be made is handled, as well
as retaining backwards compatibility with the valid cases.
Below devicetree snippets can be found that explain some of
the cases above more concretely.
Here's[0] a devicetree example where the MAC is both fixed-link and
driving a switch on MDIO (case "2" above). This needs a MDIO bus to
be created:
&fec1 {
phy-mode = "rmii";
fixed-link {
speed = <100>;
full-duplex;
};
mdio1: mdio {
switch0: switch0@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
};
};
};
Here's[1] an example where there is no MDIO bus or fixed-link for
the ethernet1 MAC, so no MDIO bus should be created since ethernet0
is the MDIO master for ethernet1's phy:
ðernet0 {
phy-mode = "sgmii";
phy-handle = <&sgmii_phy0>;
mdio {
compatible = "snps,dwmac-mdio";
sgmii_phy0: phy@8 {
compatible = "ethernet-phy-id0141.0dd4";
reg = <0x8>;
device_type = "ethernet-phy";
};
sgmii_phy1: phy@a {
compatible = "ethernet-phy-id0141.0dd4";
reg = <0xa>;
device_type = "ethernet-phy";
};
};
};
ðernet1 {
phy-mode = "sgmii";
phy-handle = <&sgmii_phy1>;
};
Finally there's descriptions like this[2] which don't describe the
MDIO bus but expect it to be created and the whole address space
scanned for a phy since there's no phy-handle or fixed-link described:
&gmac {
phy-supply = <&vcc_lan>;
phy-mode = "rmii";
snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
};
[0] https://elixir.bootlin.com/linux/v6.5-rc5/source/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
[1] https://elixir.bootlin.com/linux/v6.6-rc5/source/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
[2] https://elixir.bootlin.com/linux/v6.6-rc5/source/arch/arm64/boot/dts/rockchip/rk3368-r88.dts#L164
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (or adjacent changes of note).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The second parameter of stmmac_pltfr_init() needs the pointer of
"struct plat_stmmacenet_data". So, correct the parameter typo when calling the
function.
Otherwise, it may cause this alignment exception when doing suspend/resume.
[ 49.067201] CPU1 is up
[ 49.135258] Internal error: SP/PC alignment exception: 000000008a000000 [#1] PREEMPT SMP
[ 49.143346] Modules linked in: soc_imx9 crct10dif_ce polyval_ce nvmem_imx_ocotp_fsb_s400 polyval_generic layerscape_edac_mod snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_imx_card snd_soc_wm8962 el_enclave snd_soc_fsl_micfil rtc_pcf2127 rtc_pcf2131 flexcan can_dev snd_soc_fsl_xcvr snd_soc_fsl_sai imx8_media_dev(C) snd_soc_fsl_utils fuse
[ 49.173393] CPU: 0 PID: 565 Comm: sh Tainted: G C 6.5.0-rc4-next-20230804-05047-g5781a6249dae #677
[ 49.183721] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[ 49.189190] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 49.196140] pc : 0x80800052
[ 49.198931] lr : stmmac_pltfr_resume+0x34/0x50
[ 49.203368] sp : ffff800082f8bab0
[ 49.206670] x29: ffff800082f8bab0 x28: ffff0000047d0ec0 x27: ffff80008186c170
[ 49.213794] x26: 0000000b5e4ff1ba x25: ffff800081e5fa74 x24: 0000000000000010
[ 49.220918] x23: ffff800081fe0000 x22: 0000000000000000 x21: 0000000000000000
[ 49.228042] x20: ffff0000001b4010 x19: ffff0000001b4010 x18: 0000000000000006
[ 49.235166] x17: ffff7ffffe007000 x16: ffff800080000000 x15: 0000000000000000
[ 49.242290] x14: 00000000000000fc x13: 0000000000000000 x12: 0000000000000000
[ 49.249414] x11: 0000000000000001 x10: 0000000000000a60 x9 : ffff800082f8b8c0
[ 49.256538] x8 : 0000000000000008 x7 : 0000000000000001 x6 : 000000005f54a200
[ 49.263662] x5 : 0000000001000000 x4 : ffff800081b93680 x3 : ffff800081519be0
[ 49.270786] x2 : 0000000080800052 x1 : 0000000000000000 x0 : ffff0000001b4000
[ 49.277911] Call trace:
[ 49.280346] 0x80800052
[ 49.282781] platform_pm_resume+0x2c/0x68
[ 49.286785] dpm_run_callback.constprop.0+0x74/0x134
[ 49.291742] device_resume+0x88/0x194
[ 49.295391] dpm_resume+0x10c/0x230
[ 49.298866] dpm_resume_end+0x18/0x30
[ 49.302515] suspend_devices_and_enter+0x2b8/0x624
[ 49.307299] pm_suspend+0x1fc/0x348
[ 49.310774] state_store+0x80/0x104
[ 49.314258] kobj_attr_store+0x18/0x2c
[ 49.318002] sysfs_kf_write+0x44/0x54
[ 49.321659] kernfs_fop_write_iter+0x120/0x1ec
[ 49.326088] vfs_write+0x1bc/0x300
[ 49.329485] ksys_write+0x70/0x104
[ 49.332874] __arm64_sys_write+0x1c/0x28
[ 49.336783] invoke_syscall+0x48/0x114
[ 49.340527] el0_svc_common.constprop.0+0xc4/0xe4
[ 49.345224] do_el0_svc+0x38/0x98
[ 49.348526] el0_svc+0x2c/0x84
[ 49.351568] el0t_64_sync_handler+0x100/0x12c
[ 49.355910] el0t_64_sync+0x190/0x194
[ 49.359567] Code: ???????? ???????? ???????? ???????? (????????)
[ 49.365644] ---[ end trace 0000000000000000 ]---
Fixes: 97117eb51ec8 ("net: stmmac: platform: provide stmmac_pltfr_init()")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now there's no external users of these two functions, make them static
so that there aren't any new usages of stmmac_probe_config_dt().
To avoid forward declaration, move stmmac_remove_config_dt() location.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now, all users of the old stmmac_pltfr_remove() are converted to the
devres helper, it's time to rename stmmac_pltfr_remove_no_dt() back to
stmmac_pltfr_remove() and remove the old stmmac_pltfr_remove().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.
So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Stein reports that commit a014c35556b9 ("net: stmmac: clarify
difference between "interface" and "phy_interface"") caused breakage,
because plat->mac_interface will never be negative. Fix this by using
the "rc" temporary variable in stmmac_probe_config_dt().
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/E1qayn0-006Q8J-GE@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clarify the difference between "interface" and "phy_interface" in
struct plat_stmmacenet_data, both by adding a comment, and also
renaming "interface" to be "mac_interface". The difference between
these are:
MAC ----- optional PCS ----- SerDes ----- optional PHY ----- Media
^ ^
mac_interface phy_interface
Note that phylink currently only deals with phy_interface.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZq83-005tts-6K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All users of plat->phylink_node first convert it to a fwnode. Rather
than repeatedly convert to a fwnode, store it as a fwnode. To reflect
this change, call it plat->port_node instead - it is used for more
than just phylink.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAX8-005pTo-OT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-13-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-6-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a devres variant of stmmac_pltfr_probe() which allows users to
skip calling stmmac_pltfr_remove() at driver detach.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-11-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a devres variant of stmmac_probe_config_dt() that allows users to
skip calling stmmac_remove_config_dt() at driver detach.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-9-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a variant of stmmac_pltfr_remove() that only frees resources
allocated by stmmac_pltfr_probe() and - unlike stmmac_pltfr_remove() -
does not call stmmac_remove_config_dt().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-8-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement stmmac_pltfr_probe() which is the logical API counterpart
for stmmac_pltfr_remove(). It calls the platform's init() callback and
then probes the stmmac device.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-6-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a helper wrapper around calling the platform's exit() callback.
This allows users to skip checking if the callback exists.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-4-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a helper wrapper around calling the platform's init() callback.
This allows users to skip checking if the callback exists.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-2-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function returns zero unconditionally. Change it to return void instead
which simplifies some callers as error handing becomes unnecessary.
The function is also used for some drivers as remove callback. Switch these
to the .remove_new() callback. For some others no error can happen in the
remove callback now, convert them to .remove_new(), too.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add "snps,dwmac-5.20" compatible string for 5.20 version that can avoid
to define some platform data in the glue layer.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some of the devlink bits were tricky, but I think I got it right.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting 'snps,force_thresh_dma_mode' DT property, the following
warning is always emitted, regardless the status of force_sf_dma_mode:
dwmac-starfive 10020000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
Do not print the rather misleading message when DMA store and forward
mode is already disabled.
Fixes: e2a240c7d3bc ("driver:net:stmmac: Disable DMA store and forward mode if platform data force_thresh_dma_mode is set.")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230210202126.877548-1-cristian.ciocaltea@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The function returns zero unconditionally. Change it to return void instead
which simplifies some callers as error handing becomes unnecessary.
This also makes it more obvious that most platform remove callbacks always
return zero.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230211112431.214252-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In dt-binding snps,dwmac.yaml, some properties under "snps,axi-config"
node are named without "axi_" prefix, but the driver expects the
prefix. Since the dt-binding has been there for a long time, we'd
better make driver match the binding for compatibility.
Fixes: afea03656add ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221202161739.2203-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Parse new property 'snps,clk-csr' firstly because the new property
is documented in binding file, if failed, fall back to old property
'clk_csr' for legacy case
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor spell fix related to 'stmmac_clk_csr_set()' inside a
comment used in the 'stmmac_probe_config_dt()' function.
Cc: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20220924104514.1666947-1-bhupesh.sharma@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current stmmac driver will prepare/enable ptp_ref clock in
stmmac_init_tstamp_counter().
The stmmac_pltfr_noirq_suspend will disable it once in suspend flow.
But in resume flow,
stmmac_pltfr_noirq_resume --> stmmac_init_tstamp_counter
stmmac_resume --> stmmac_hw_setup --> stmmac_init_ptp --> stmmac_init_tstamp_counter
ptp_ref clock reference counter increases twice, which leads to unbalance
ptp clock when resume back.
Move ptp_ref clock prepare/enable out of stmmac_init_tstamp_counter to fix it.
Fixes: 0735e639f129d ("net: stmmac: skip only stmmac_ptp_register when resume from suspend")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 9cbadf094d9d ("net: stmmac: support max-speed device tree
property"), when DT platforms don't set "max-speed", max_speed is set to
-1; for non-DT platforms, it stays the default 0.
Prior to commit eeef2f6b9f6e ("net: stmmac: Start adding phylink support"),
the check for a valid max_speed setting was to check if it was greater
than zero. This commit got it right, but subsequent patches just checked
for non-zero, which is incorrect for DT platforms.
In commit 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
the conversion switched completely to checking for non-zero value as a
valid value, which caused 1000base-T to stop getting advertised by
default.
Instead of trying to fix all the checks, simply leave max_speed alone if
DT property parsing fails.
Fixes: 9cbadf094d9d ("net: stmmac: support max-speed device tree property")
Fixes: 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220331184832.16316-1-wens@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.
To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.
Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.
As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.
Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use __maybe_unused for noirq_suspend()/noirq_resume() hooks to avoid
build warning with !CONFIG_PM_SLEEP:
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:796:12: error: 'stmmac_pltfr_noirq_resume' defined but not used [-Werror=unused-function]
796 | static int stmmac_pltfr_noirq_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:775:12: error: 'stmmac_pltfr_noirq_suspend' defined but not used [-Werror=unused-function]
775 | static int stmmac_pltfr_noirq_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: 276aae377206 ("net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 5f58591323bf ("net: stmmac: delete the eee_ctrl_timer after
napi disabled"), this patch tries to fix system hang caused by eee_ctrl_timer,
unfortunately, it only can resolve it for system reboot stress test. System
hang also can be reproduced easily during system suspend/resume stess test
when mount NFS on i.MX8MP EVK board.
In stmmac driver, eee feature is combined to phylink framework. When do
system suspend, phylink_stop() would queue delayed work, it invokes
stmmac_mac_link_down(), where to deactivate eee_ctrl_timer synchronizly.
In above commit, try to fix issue by deactivating eee_ctrl_timer obviously,
but it is not enough. Looking into eee_ctrl_timer expire callback
stmmac_eee_ctrl_timer(), it could enable hareware eee mode again. What is
unexpected is that LPI interrupt (MAC_Interrupt_Enable.LPIEN bit) is always
asserted. This interrupt has chance to be issued when LPI state entry/exit
from the MAC, and at that time, clock could have been already disabled.
The result is that system hang when driver try to touch register from
interrupt handler.
The reason why above commit can fix system hang issue in stmmac_release()
is that, deactivate eee_ctrl_timer not just after napi disabled, further
after irq freed.
In conclusion, hardware would generate LPI interrupt when clock has been
disabled during suspend or resume, since hardware is in eee mode and LPI
interrupt enabled.
Interrupts from MAC, MTL and DMA level are enabled and never been disabled
when system suspend, so postpone clocks management from suspend stage to
noirq suspend stage should be more safe.
Fixes: 5f58591323bf ("net: stmmac: delete the eee_ctrl_timer after napi disabled")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "plat->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.
Fixes: b9f0b2f634c0 ("net: stmmac: platform: fix probe for ACPI devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().
Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().
Fixes: commit d2ed0a7755fe ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently assuming that GMAC_AHB_RESET will already be deasserted
by the bootloader. However if this has not been done, probing of the GMAC
will fail. To remedy this we must ensure GMAC_AHB_RESET has been deasserted
prior to probing.
v2 changes:
- remove NULL condition check for stmmac_ahb_rst in stmmac_main.c
- unwrap dev_err() message in stmmac_main.c
- add PTR_ERR() around plat->stmmac_ahb_rst in stmmac_platform.c
v3 changes:
- add error pointer to dev_err() output
- add reset_control_assert(stmmac_ahb_rst) in stmmac_dvr_remove
- revert PTR_ERR() around plat->stmmac_ahb_rst since this is performed
on the returned value of ret by the calling function
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The statement of the last "if (xxx)" branch is the same as the "else"
branch. Delete it to simplify code.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of the CONFIG_PM_SLEEP ifdefery to fix the build error
and use __maybe_unused for the suspend()/resume() hooks to avoid
build warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:21:
error: 'stmmac_runtime_suspend' undeclared here (not in a function); did you mean 'stmmac_suspend'?
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:342:21: note: in definition of macro 'SET_RUNTIME_PM_OPS'
342 | .runtime_suspend = suspend_fn, \
| ^~~~~~~~~~
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:45:
error: 'stmmac_runtime_resume' undeclared here (not in a function)
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:343:20: note: in definition of macro 'SET_RUNTIME_PM_OPS'
343 | .runtime_resume = resume_fn, \
| ^~~~~~~~~
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch intends to add clocks management for stmmac driver:
If CONFIG_PM enabled:
1. Keep clocks disabled after driver probed.
2. Enable clocks when up the net device, and disable clocks when down
the net device.
If CONFIG_PM disabled:
Keep clocks always enabled after driver probed.
Note:
1. It is fine for ethtool, since the way of implementing ethtool_ops::begin
in stmmac is only can be accessed when interface is enabled, so the clocks
are ticked.
2. The MDIO bus has a different life cycle to the MAC, need ensure
clocks are enabled when _mdio_read/write() need clocks, because these
functions can be called while the interface it not opened.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the devm_reset_control_get_optional() and devm_clk_get_optional()
rather than open coding them.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201112092606.5173aa6f@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add "snps,dwmac-5.10a" compatible string for 5.10a version that can
avoid to define some plat data in glue layer.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_ioremap_resource() to simplify code, which
contains platform_get_resource and devm_ioremap_resource.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The specification of a "eth-ck" and a "ptp_ref" clock is optional per
the binding and the driver handles them gracefully.
Demote the output to an info message accordingly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
