| Age | Commit message (Collapse) | Author |
|---|
|
ETHER_CLK_SEL_FREQ_SEL_2P5M is not 0 bit of the register. This is a
value, which is 0. Fix from BIT(0) to 0.
Reported-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Fixes: b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211223073633.101306-1-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the u32 variable to type u64 in a context where expression of
type u64 is required to avoid potential overflow.
Fixes: e9e3720002f6 ("net: stmmac: ptp: update tas basetime after ptp adjust")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://lore.kernel.org/r/20211223073928.37371-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KASAN reports an out-of-bounds read in rk_gmac_setup on the line:
while (ops->regs[i]) {
This happens for most platforms since the regs flexible array member is
empty, so the memory after the ops structure is being read here. It
seems that mostly this happens to contain zero anyway, so we get lucky
and everything still works.
To avoid adding redundant data to nearly all the ops structures, add a
new flag to indicate whether the regs field is valid and avoid this loop
when it is not.
Fixes: 3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To replicate the issue:-
1) Add 1 flower filter for VLAN Priority based frame steering:-
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
$ tc filter add dev $IFDEVNAME parent ffff: protocol 802.1Q \
flower vlan_prio 0 hw_tc 0
2) Get the 'pref' id
$ tc filter show dev $IFDEVNAME ingress
3) Delete a specific tc flower record (say pref 49151)
$ tc filter del dev $IFDEVNAME parent ffff: pref 49151
From dmesg, we will observe kernel NULL pointer ooops
[ 197.170464] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 197.171367] #PF: supervisor read access in kernel mode
[ 197.171367] #PF: error_code(0x0000) - not-present page
[ 197.171367] PGD 0 P4D 0
[ 197.171367] Oops: 0000 [#1] PREEMPT SMP NOPTI
<snip>
[ 197.171367] RIP: 0010:tc_setup_cls+0x20b/0x4a0 [stmmac]
<snip>
[ 197.171367] Call Trace:
[ 197.171367] <TASK>
[ 197.171367] ? __stmmac_disable_all_queues+0xa8/0xe0 [stmmac]
[ 197.171367] stmmac_setup_tc_block_cb+0x70/0x110 [stmmac]
[ 197.171367] tc_setup_cb_destroy+0xb3/0x180
[ 197.171367] fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
The above issue is due to previous incorrect implementation of
tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule()
to get struct flow_rule *rule which is no longer valid for tc filter
delete operation.
struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
struct flow_dissector *dissector = rule->match.dissector;
So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for
earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(),
this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload
record for 'RX frame steering' tc flower, currently used for VLAN
priority. The implementation has taken consideration for future extension
to include other type RX frame steering such as EtherType based.
v2:
- Clean up overly extensive backtrace and rewrite git message to better
explain the kernel NULL pointer issue.
Fixes: 0e039f5cf86c ("net: stmmac: add RX frame steering based on VLAN priority in tc flower")
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use page_pool_alloc_pages instead of page_pool_dev_alloc_pages, which
can give the gfp parameter, in the case of not supporting 64-bit width,
using 32-bit address memory can reduce a copy from swiotlb.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver assumes that split headers can be enabled/disabled without
stopping/starting the device, so it writes DMA_CHAN_CONTROL from
stmmac_set_features(). However, on my system (IP v5.10a without Split
Header support), simply writing DMA_CHAN_CONTROL when DMA is running
(for example, with the commands below) leads to a TX watchdog timeout.
host$ socat TCP-LISTEN:1024,fork,reuseaddr - &
device$ ethtool -K eth0 tso off
device$ ethtool -K eth0 tso on
device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024
<tx watchdog timeout>
Note that since my IP is configured without Split Header support, the
driver always just reads and writes the same value to the
DMA_CHAN_CONTROL register.
I don't have access to any platforms with Split Header support so I
don't know if these writes to the DMA_CHAN_CONTROL while DMA is running
actually work properly on such systems. I could not find anything in
the databook that says that DMA_CHAN_CONTROL should not be written when
the DMA is running.
But on systems without Split Header support, there is in any case no
need to call enable_sph() in stmmac_set_features() at all since SPH can
never be toggled, so we can avoid the watchdog timeout there by skipping
this call.
Fixes: 8c6fc097a2f4acf ("net: stmmac: gmac4+: Add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207a2d ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4961 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a6be ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.
To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.
Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.
As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.
Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bug report came up when we were testing the device driver
by fuzzing. It shows that buf1_len can get underflowed and be
0xfffffffc (4294967292).
This bug is triggerable with a compromised/malfunctioning device.
We found the bug through QEMU emulation tested the patch with
emulation. We did NOT test it on real hardware.
Attached is the bug report by fuzzing.
BUG: KASAN: use-after-free in stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
Read of size 4294967292 at addr ffff888016358000 by task ksoftirqd/0/9
CPU: 0 PID: 9 Comm: ksoftirqd/0 Tainted: G W 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
__kasan_report.cold+0x37/0x7c
? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
kasan_report+0xe/0x20
check_memory_region+0x15a/0x1d0
memcpy+0x20/0x50
stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
? stmmac_suspend+0x850/0x850 [stmmac]
? __next_timer_interrupt+0xba/0xf0
net_rx_action+0x363/0xbd0
? call_timer_fn+0x240/0x240
? __switch_to_asm+0x40/0x70
? napi_busy_loop+0x520/0x520
? __schedule+0x839/0x15a0
__do_softirq+0x18c/0x634
? takeover_tasklets+0x5f0/0x5f0
run_ksoftirqd+0x15/0x20
smpboot_thread_fn+0x2f1/0x6b0
? smpboot_unregister_percpu_thread+0x160/0x160
? __kthread_parkme+0x80/0x100
? smpboot_unregister_percpu_thread+0x160/0x160
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent addition of timestamp correction to compensate the CDC error
introduced a subtle signed/unsigned bug in stmmac_get_tx_hwtstamp() while
it managed for some obscure reason to avoid that in stmmac_get_rx_hwtstamp().
The issue is:
s64 adjust = 0;
u64 ns;
adjust += -(2 * (NSEC_PER_SEC / priv->plat->clk_ptp_rate));
ns += adjust;
works by chance on 64bit, but falls apart on 32bit because the compiler
knows that adjust fits into 32bit and then treats the addition as a u64 +
u32 resulting in an off by ~2 seconds failure.
The RX variant uses an u64 for adjust and does the adjustment via
ns -= adjust;
because consistency is obviously overrated.
Get rid of the pointless zero initialized adjust variable and do:
ns -= (2 * NSEC_PER_SEC) / priv->plat->clk_ptp_rate;
which is obviously correct and spares the adjust obfuscation. Aside of that
it yields a more accurate result because the multiplication takes place
before the integer divide truncation and not afterwards.
Stick the calculation into an inline so it can't be accidentally
disimproved. Return an u32 from that inline as the result is guaranteed
to fit which lets the compiler optimize the substraction.
Cc: stable@vger.kernel.org
Fixes: 3600be5f58c1 ("net: stmmac: add timestamp correction to rid CDC sync error")
Reported-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Benedikt Spranger <b.spranger@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel EHL
Link: https://lore.kernel.org/r/87mtm578cs.ffs@tglx
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to upstream commit 5ec55823438e("net: stmmac:
add clocks management for gmac driver"), it improve clocks
management for stmmac driver. So, it is necessary to implement
the runtime callback in dwmac-socfpga driver because it doesn't
use the common stmmac_pltfr_pm_ops instance. Otherwise, clocks
are not disabled when system enters suspend status.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit fe28c53ed71d ("net: stmmac: fix taprio configuration when
base_time is in the past") allowed some base time values in the past,
but apparently not all, the base-time value of 0 (Jan 1st 1970) is still
explicitly denied by the driver.
Remove the bogus check.
Fixes: b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of simnple overlapping additions.
With a build fix from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334bf2 ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some old IPs do not provide the hardware feature register.
On these IPs, this register is read 0x00000000.
In old driver version, this feature was handled but a regression came
with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function").
Indeed, this commit removes the return value in dma->get_hw_feature().
This return value was used to indicate the validity of retrieved
information and used later on in stmmac_hw_init() to override
priv->plat data if this hardware feature were valid.
This patch restores the return code in ->get_hw_feature() in order
to indicate the hardware feature validity and override priv->plat
data only if this hardware feature is valid.
Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006180944.GA913477@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current implementation enable PCS EEE feature in the event of link
up, but PCS EEE feature is not disabled on link down.
This patch makes sure PCE EEE feature is disabled on link down.
Fixes: 656ed8b015f1 ("net: stmmac: fix EEE init issue when paired with EEE capable PHYs")
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
while getting rid of a runtime PM warning ended up breaking ethernet
on rk3399 based devices. By dropping an extra reference to the device,
the commit ends up enabling suspend / resume of the ethernet device -
which appears to be broken.
While the issue with runtime pm is being investigated, partially
revert commit 2d26f6e39afb to restore the network on rk3399.
Fixes: 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Cc: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210929135049.3426058-1-punitagrawal@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/phy/bcm7xxx.c
d88fd1b546ff ("net: phy: bcm7xxx: Fixed indirect MMD operations")
f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165")
net/sched/sch_api.c
b193e15ac69d ("net: prevent user from passing illegal stab size")
69508d43334e ("net_sched: Use struct_size() and flex_array_size() helpers")
Both cases trivial - adjacent code additions.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When STMMAC is paired with Energy-Efficient Ethernet(EEE) capable PHY,
and the PHY is advertising EEE by default, we need to enable EEE on the
xPCS side too, instead of having user to manually trigger the enabling
config via ethtool.
Fixed this by adding xpcs_config_eee() call in stmmac_eee_init().
Fixes: 7617af3d1a5e ("net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet")
Cc: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My previous patch had an off-by-one error in the added sanity
check, the arrays are MTL_MAX_{RX,TX}_QUEUES long, so if that
index is that number, it has overflown.
The patch silenced the warning anyway because the strings could
no longer overlap with the input, but they could still overlap
with other fields.
Fixes: 3e0d5699a975 ("net: stmmac: fix gcc-10 -Wrestrict warning")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-10 and later warn about a theoretical array overrun when
accessing priv->int_name_rx_irq[i] with an out of bounds value
of 'i':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_request_irq_multi_msi':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3528:17: error: 'snprintf' argument 4 may overlap destination object 'dev' [-Werror=restrict]
3528 | snprintf(int_name, int_name_len, "%s:%s-%d", dev->name, "tx", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3404:60: note: destination object referenced by 'restrict'-qualified argument 1 was declared here
3404 | static int stmmac_request_irq_multi_msi(struct net_device *dev)
| ~~~~~~~~~~~~~~~~~~~^~~
The warning is a bit strange since it's not actually about the array
bounds but rather about possible string operations with overlapping
arguments, but it's not technically wrong.
Avoid the warning by adding an extra bounds check.
Fixes: 8532f613bc78 ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX")
Link: https://lore.kernel.org/all/20210421134743.3260921-1-arnd@kernel.org/
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use __maybe_unused for noirq_suspend()/noirq_resume() hooks to avoid
build warning with !CONFIG_PM_SLEEP:
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:796:12: error: 'stmmac_pltfr_noirq_resume' defined but not used [-Werror=unused-function]
796 | static int stmmac_pltfr_noirq_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:775:12: error: 'stmmac_pltfr_noirq_suspend' defined but not used [-Werror=unused-function]
775 | static int stmmac_pltfr_noirq_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: 276aae377206 ("net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 5f58591323bf ("net: stmmac: delete the eee_ctrl_timer after
napi disabled"), this patch tries to fix system hang caused by eee_ctrl_timer,
unfortunately, it only can resolve it for system reboot stress test. System
hang also can be reproduced easily during system suspend/resume stess test
when mount NFS on i.MX8MP EVK board.
In stmmac driver, eee feature is combined to phylink framework. When do
system suspend, phylink_stop() would queue delayed work, it invokes
stmmac_mac_link_down(), where to deactivate eee_ctrl_timer synchronizly.
In above commit, try to fix issue by deactivating eee_ctrl_timer obviously,
but it is not enough. Looking into eee_ctrl_timer expire callback
stmmac_eee_ctrl_timer(), it could enable hareware eee mode again. What is
unexpected is that LPI interrupt (MAC_Interrupt_Enable.LPIEN bit) is always
asserted. This interrupt has chance to be issued when LPI state entry/exit
from the MAC, and at that time, clock could have been already disabled.
The result is that system hang when driver try to touch register from
interrupt handler.
The reason why above commit can fix system hang issue in stmmac_release()
is that, deactivate eee_ctrl_timer not just after napi disabled, further
after irq freed.
In conclusion, hardware would generate LPI interrupt when clock has been
disabled during suspend or resume, since hardware is in eee mode and LPI
interrupt enabled.
Interrupts from MAC, MTL and DMA level are enabled and never been disabled
when system suspend, so postpone clocks management from suspend stage to
noirq suspend stage should be more safe.
Fixes: 5f58591323bf ("net: stmmac: delete the eee_ctrl_timer after napi disabled")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can reproduce this issue with below steps:
1) enable WoL on the host
2) host system suspended
3) remote client send out wakeup packets
We can see that host system resume back, but can't work, such as ping failed.
After a bit digging, this issue is introduced by the commit 46f69ded988d
("net: stmmac: Use resolved link config in mac_link_up()"), which use
the finalised link parameters in mac_link_up() rather than the
parameters in mac_config().
There are two scenarios for MAC suspend/resume in STMMAC driver:
1) MAC suspend with WoL inactive, stmmac_suspend() call
phylink_mac_change() to notify phylink machine that a change in MAC
state, then .mac_link_down callback would be invoked. Further, it will
call phylink_stop() to stop the phylink instance. When MAC resume back,
firstly phylink_start() is called to start the phylink instance, then
call phylink_mac_change() which will finally trigger phylink machine to
invoke .mac_config and .mac_link_up callback. All is fine since
configuration in these two callbacks will be initialized, that means MAC
can restore the state.
2) MAC suspend with WoL active, phylink_mac_change() will put link
down, but there is no phylink_stop() to stop the phylink instance, so it
will link up again, that means .mac_config and .mac_link_up would be
invoked before system suspended. After system resume back, it will do
DMA initialization and SW reset which let MAC lost the hardware setting
(i.e MAC_Configuration register(offset 0x0) is reset). Since link is up
before system suspended, so .mac_link_up would not be invoked after
system resume back, lead to there is no chance to initialize the
configuration in .mac_link_up callback, as a result, MAC can't work any
longer.
After discussed with Russell King [1], we confirm that phylink framework
have not take WoL into consideration yet. This patch calls
phylink_suspend()/phylink_resume() functions which is newly introduced
by Russell King to fix this issue.
[1] https://lore.kernel.org/netdev/20210901090228.11308-1-qiangqing.zhang@nxp.com/
Fixes: 46f69ded988d ("net: stmmac: Use resolved link config in mac_link_up()")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the return value when phy_mode < 0.
Signed-off-by: zhaoxiao <long870912@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tx_done is not used for napi_complete_done(). Thus, NAPI busy polling
mechanism by gro_flush_timeout and napi_defer_hard_irqs will not able
be triggered after a packet is transmitted when there is no receive
packet.
Fix this by taking the maximum value between tx_done and rx_done as
overall budget completed by the rxtx NAPI poll to ensure XDP Tx ZC
operation is continuously polling for next Tx frame. This gives
benefit of lower packet submission processing latency and jitter
under XDP Tx ZC mode.
Performance of tx-only using xdp-sock on Intel ADL-S platform is
the same with and without this patch.
root@intel-corei7-64:~# ./xdpsock -i enp0s30f4 -t -z -q 1 -n 10
sock0@enp0s30f4:1 txonly xdp-drv
pps pkts 10.00
rx 0 0
tx 511630 8659520
sock0@enp0s30f4:1 txonly xdp-drv
pps pkts 10.00
rx 0 0
tx 511625 13775808
sock0@enp0s30f4:1 txonly xdp-drv
pps pkts 10.00
rx 0 0
tx 511619 18892032
Fixes: 132c32ee5bc0 ("net: stmmac: Add TX via XDP zero-copy socket")
Cc: <stable@vger.kernel.org> # 5.13.x
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/wwan/mhi_wwan_mbim.c - drop the extra arg.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure a valid XSK buffer before proceed to free the xdp buffer.
The following kernel panic is observed without this patch:
RIP: 0010:xp_free+0x5/0x40
Call Trace:
stmmac_napi_poll_rxtx+0x332/0xb30 [stmmac]
? stmmac_tx_timer+0x3c/0xb0 [stmmac]
net_rx_action+0x13d/0x3d0
__do_softirq+0xfc/0x2fb
? smpboot_register_percpu_thread+0xe0/0xe0
run_ksoftirqd+0x32/0x70
smpboot_thread_fn+0x1d8/0x2c0
kthread+0x169/0x1a0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
---[ end trace 0000000000000002 ]---
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.
Fix this by changing the XDP pool setup sequence to:
1. disable napi before free xsk_pool
2. enable napi after init xsk_pool
The following kernel panic is observed without this patch:
RIP: 0010:xsk_uses_need_wakeup+0x5/0x10
Call Trace:
stmmac_napi_poll_rxtx+0x3a9/0xae0 [stmmac]
__napi_poll+0x27/0x130
net_rx_action+0x233/0x280
__do_softirq+0xe2/0x2b6
run_ksoftirqd+0x1a/0x20
smpboot_thread_fn+0xac/0x140
? sort_range+0x20/0x20
kthread+0x124/0x150
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
---[ end trace a77c8956b79ac107 ]---
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 2c896fb02e7f65299646f295a007bda043e0f382
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.
In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.
The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.
Fixes: 5ec55823438e850c91c6b92aec93fb04ebde29e2 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.
Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.
The following kernel panic is observed without this patch:
RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---
Fixes: b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a955318fe67e ("stmmac: align RX buffers"),
which breaks at least one platform (Nvidia Jetson-X1), causing
packet corruption. This is 100% reproducible, and reverting
the patch results in a working system again.
Given that it is "only" a performance optimisation, let's
return to a known working configuration until we can have a
good understanding of what is happening here.
Fixes: a955318fe67e ("stmmac: align RX buffers")
Cc: Matteo Croce <mcroce@linux.microsoft.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/netdev/871r71azjw.wl-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820183002.457226-1-maz@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adding ethtool per-queue statistics support to show number of interrupts
generated at DMA tx and DMA rx. All the counters are incremented at
dwmac4_dma_interrupt function.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding generic ethtool per-queue statistic framework to display the
statistics for each rx/tx queue. In future, users can avail it to add
more per-queue specific counters. Number of rx/tx queues displayed is
depending on the available rx/tx queues in that particular MAC config
and this number is limited up to the MTL_MAX_{RX|TX}_QUEUES defined
in the driver.
Ethtool per-queue statistic display will look like below, when users
start adding more counters.
Example:
q0_tx_statA:
q0_tx_statB:
q0_tx_statC:
|
q0_tx_statX:
.
.
.
qMAX_tx_statA:
qMAX_tx_statB:
qMAX_tx_statC:
|
qMAX_tx_statX:
q0_rx_statA:
q0_rx_statB:
q0_rx_statC:
|
q0_rx_statX:
.
.
.
qMAX_rx_statA:
qMAX_rx_statB:
qMAX_rx_statC:
|
qMAX_rx_statX:
In addition, this patch has the support on displaying the number of
packets received and transmitted per queue.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA channel status "Transmit buffer unavailable(TBU)" bit is not
considered as a successful dma tx. Hence, it should not affect
all the irq count statistic.
Fixes: 1103d3a5531c ("net: stmmac: dwmac4: Also use TBU interrupt to clean TX path")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicting commits, all resolutions pretty trivial:
drivers/bus/mhi/pci_generic.c
5c2c85315948 ("bus: mhi: pci-generic: configurable network interface MRU")
56f6f4c4eb2a ("bus: mhi: pci_generic: Apply no-op for wake using sideband wake boolean")
drivers/nfc/s3fwrn5/firmware.c
a0302ff5906a ("nfc: s3fwrn5: remove unnecessary label")
46573e3ab08f ("nfc: s3fwrn5: fix undefined parameter values in dev_err()")
801e541c79bb ("nfc: s3fwrn5: fix undefined parameter values in dev_err()")
MAINTAINERS
7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
8a7b46fa7902 ("MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assign dwmac5_est_irq_status to est_irq_status callback function for
GMAC 4.10 and 5.10. With this, EST related interrupts could be handled
properly.
Fixes: e49aa315cb01 ("net: stmmac: EST interrupts handling and error reporting")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Acked-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
