| Age | Commit message (Collapse) | Author |
|---|
|
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b929 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently using plain XDP/ZC sockets on stmmac results in a kernel crash:
|[ 255.822584] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
|[...]
|[ 255.822764] Call trace:
|[ 255.822766] stmmac_tx_clean.constprop.0+0x848/0xc38
The program counter indicates xsk_tx_metadata_complete(). It works on
compl->tx_timestamp, which is not set by xsk_tx_metadata_to_compl() due to
missing meta data. Therefore, call xsk_tx_metadata_complete() only when
meta data is actually used.
Tested on imx93 without XDP, with XDP and with XDP/ZC.
Fixes: 1347b419318d ("net: stmmac: Add Tx HWTS support to XDP ZC")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/netdev/87r0h7wg8u.fsf@kurt.kurt.home/
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20240222-stmmac_xdp-v2-1-4beee3a037e4@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix EST offset for dwmac 5.10.
Currently configuring Qbv doesn't work as expected. The schedule is
configured, but never confirmed:
|[ 128.250219] imx-dwmac 428a0000.ethernet eth1: configured EST
The reason seems to be the refactoring of the EST code which set the wrong
EST offset for the dwmac 5.10. After fixing this it works as before:
|[ 106.359577] imx-dwmac 428a0000.ethernet eth1: configured EST
|[ 128.430715] imx-dwmac 428a0000.ethernet eth1: EST: SWOL has been switched
Tested on imx93.
Fixes: c3f3b97238f6 ("net: stmmac: Refactor EST implementation")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240220-stmmac_est-v1-1-c41f9ae2e7b7@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If 'dev' or 'data' is NULL, the 'priv' variable has an incorrect address
when dereferencing calling netdev_err().
Since we get as 'dev_id' or 'data' what was passed as the 'dev' argument
to request_irq() during interrupt initialization (that is, the net_device
and rx/tx queue pointers initialized at the time of the call) and since
there are usually no checks for the 'dev_id' argument in such handlers
in other drivers, remove these checks from the handlers in stmmac driver.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8532f613bc78 ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX")
Signed-off-by: Pavel Sakharov <p.sakharov@ispras.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained by a comment in <linux/u64_stats_sync.h>, write side of struct
u64_stats_sync must ensure mutual exclusion, or one seqcount update could
be lost on 32-bit platforms, thus blocking readers forever. Such lockups
have been observed in real world after stmmac_xmit() on one CPU raced with
stmmac_napi_poll_tx() on another CPU.
To fix the issue without introducing a new lock, split the statics into
three parts:
1. fields updated only under the tx queue lock,
2. fields updated only during NAPI poll,
3. fields updated only from interrupt context,
Updates to fields in the first two groups are already serialized through
other locks. It is sufficient to split the existing struct u64_stats_sync
so that each group has its own.
Note that tx_set_ic_bit is updated from both contexts. Split this counter
so that each context gets its own, and calculate their sum to get the total
value in stmmac_get_ethtool_stats().
For the third group, multiple interrupts may be processed by different CPUs
at the same time, but interrupts on the same CPU will not nest. Move fields
from this group to a newly created per-cpu struct stmmac_pcpu_stats.
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Link: https://lore.kernel.org/netdev/Za173PhviYg-1qIn@torres.zugschlus.de/t/
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 56e58d6c8a56 ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a56 ("net: stmmac: Implement Safety Features in XGMAC core")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSO and TBS cannot coexist. For now we set i.MX Ethernet QOS controller to
use the first TX queue with TSO and the rest for TBS.
TX queues with TBS can support etf qdisc hw offload.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With the dma conf being reallocated on each call to stmmac_open(), any
information in there is lost, unless we specifically handle it.
The STMMAC_TBS_EN bit is set when adding an etf qdisc, and the etf qdisc
therefore would stop working when link was set down and then back up.
Fixes: ba39b344e924 ("net: ethernet: stmicro: stmmac: generate stmmac dma conf before open")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
BTW: my hardware's synopsys id is 0x37.
Fixes: c5e4ddbdfa11 ("net: stmmac: Add support for optional reset control")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/AS8P193MB1285A810BD78C111E7F6AA34E4752@AS8P193MB1285.EURP193.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some DSA tagging protocols change the EtherType field in the MAC header
e.g. DSA_TAG_PROTO_(DSA/EDSA/BRCM/MTK/RTL4C_A/SJA1105). On TX these tagged
frames are ignored by the checksum offload engine and IP header checker of
some stmmac cores.
On RX, the stmmac driver wrongly assumes that checksums have been computed
for these tagged packets, and sets CHECKSUM_UNNECESSARY.
Add an additional check in the stmmac TX and RX hotpaths so that COE is
deactivated for packets with ethertypes that will not trigger the COE and
IP header checks.
Fixes: 6b2c6e4a938f ("net: stmmac: propagate feature flags to vlan")
Cc: <stable@vger.kernel.org>
Reported-by: Richard Tresidder <rtresidd@electromag.com.au>
Link: https://lore.kernel.org/netdev/e5c6c75f-2dfa-4e50-a1fb-6bf4cdb617c2@electromag.com.au/
Reported-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://lore.kernel.org/netdev/c57283ed-6b9b-b0e6-ee12-5655c1c54495@bootlin.com/
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
calls
We found the following dmesg calltrace when testing the GMAC NIC notebook:
[9.448656] ------------[ cut here ]------------
[9.448658] Unbalanced IRQ 43 wake disable
[9.448673] WARNING: CPU: 3 PID: 1083 at kernel/irq/manage.c:688 irq_set_irq_wake+0xe0/0x128
[9.448717] CPU: 3 PID: 1083 Comm: ethtool Tainted: G O 4.19 #1
[9.448773] ...
[9.448774] Call Trace:
[9.448781] [<9000000000209b5c>] show_stack+0x34/0x140
[9.448788] [<9000000000d52700>] dump_stack+0x98/0xd0
[9.448794] [<9000000000228610>] __warn+0xa8/0x120
[9.448797] [<9000000000d2fb60>] report_bug+0x98/0x130
[9.448800] [<900000000020a418>] do_bp+0x248/0x2f0
[9.448805] [<90000000002035f4>] handle_bp_int+0x4c/0x78
[9.448808] [<900000000029ea40>] irq_set_irq_wake+0xe0/0x128
[9.448813] [<9000000000a96a7c>] stmmac_set_wol+0x134/0x150
[9.448819] [<9000000000be6ed0>] dev_ethtool+0x1368/0x2440
[9.448824] [<9000000000c08350>] dev_ioctl+0x1f8/0x3e0
[9.448827] [<9000000000bb2a34>] sock_ioctl+0x2a4/0x450
[9.448832] [<900000000046f044>] do_vfs_ioctl+0xa4/0x738
[9.448834] [<900000000046f778>] ksys_ioctl+0xa0/0xe8
[9.448837] [<900000000046f7d8>] sys_ioctl+0x18/0x28
[9.448840] [<9000000000211ab4>] syscall_common+0x20/0x34
[9.448842] ---[ end trace 40c18d9aec863c3e ]---
Multiple disable_irq_wake() calls will keep decreasing the IRQ
wake_depth, When wake_depth is 0, calling disable_irq_wake() again,
will report the above calltrace.
Due to the need to appear in pairs, we cannot call disable_irq_wake()
without calling enable_irq_wake(). Fix this by making sure there are
no unbalanced disable_irq_wake() calls.
Fixes: 3172d3afa998 ("stmmac: support wake up irq from external sources (v3)")
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240112021249.24598-1-maqianga@uniontech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently get/set_link_ksettings ethtool ops are dependent on PCS.
When PCS is integrated, it will not have separate link config.
Bypass configuring and checking PCS for integrated PCS.
Fixes: aa571b6275fb ("net: stmmac: add new switch to struct plat_stmmacenet_data")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge in late fixes to prepare for the 6.8 net-next PR
No conflicts.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Revert "net: stmmac: Use interrupt mode INTM=1 for per channel irq"
This reverts commit 36af9f25ddfd311da82628f194c794786467cb12.
Revert "net: stmmac: Add support for TX/RX channel interrupt"
This reverts commit 9072e03d32088137a435ddf3aa95fd6e038d69d8.
Revert "net: stmmac: Make MSI interrupt routine generic"
This reverts commit 477bd4beb93bf9ace9bda71f1437b191befa9cf4.
Revert "dt-bindings: net: snps,dwmac: per channel irq"
This reverts commit 67d47c8ada0f8795bfcdb85cc8f2ad3ce556674b.
Device tree bindings need to be reviewed.
Link: https://lore.kernel.org/all/2df9fe3e-7971-4aa2-89a9-0e085b3b00d7@linaro.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable per DMA channel interrupt that uses shared peripheral
interrupt (SPI), so only per channel TX and RX intr (TI/RI)
are handled by TX/RX ISR without calling common interrupt ISR.
Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable TX/RX channel interrupt registration for MAC that interrupts CPU
through shared peripheral interrupt (SPI).
Per channel interrupts and interrupt-names are registered through,
Eg: 4 tx and 4 rx channels:
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "dma_tx0",
"dma_tx1",
"dma_tx2",
"dma_tx3",
"dma_rx0",
"dma_rx1",
"dma_rx2",
"dma_rx3";
Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no support for per DMA channel interrupt for non-MSI platform,
where the MAC's per channel interrupt hooks up to interrupt controller(GIC)
through shared peripheral interrupt(SPI) to handle interrupt from TX/RX
transmit channel.
This patch generalize the existing MSI ISR to also support non-MSI
platform.
Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix per-queue statistics for devices with more than one queue.
The output data pointer is currently reset in each loop iteration,
effectively summing all queue statistics in the first four u64 values.
The summary values are not even labeled correctly. For example, if eth0 has
2 queues, ethtool -S eth0 shows:
q0_tx_pkt_n: 374 (actually tx_pkt_n over all queues)
q0_tx_irq_n: 23 (actually tx_normal_irq_n over all queues)
q1_tx_pkt_n: 462 (actually rx_pkt_n over all queues)
q1_tx_irq_n: 446 (actually rx_normal_irq_n over all queues)
q0_rx_pkt_n: 0
q0_rx_irq_n: 0
q1_rx_pkt_n: 0
q1_rx_irq_n: 0
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c
23c93c3b6275 ("bnxt_en: do not map packet buffers twice")
6d1add95536b ("bnxt_en: Modify TX ring indexing logic.")
tools/testing/selftests/net/Makefile
2258b666482d ("selftests: add vlan hw filter tests")
a0bc96c0cd6e ("selftests: net: verify fq per-band packet limit")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag")
Cc: <stable@vger.kernel.org> # 6.6
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently a MDIO bus is created if the devicetree description is either:
1. Not fixed-link
2. fixed-link but contains a MDIO bus as well
The "1" case above isn't always accurate. If there's a phy-handle,
it could be referencing a phy on another MDIO controller's bus[1]. In
this case, where the MDIO bus is not described at all, currently
stmmac will make a MDIO bus and scan its address space to discover
phys (of which there are none). This process takes time scanning a bus
that is known to be empty, delaying time to complete probe.
There are also a lot of upstream devicetrees[2] that expect a MDIO bus
to be created, scanned for phys, and the first one found connected
to the MAC. This case can be inferred from the platform description by
not having a phy-handle && not being fixed-link. This hits case "1" in
the current driver's logic, and must be handled in any logic change here
since it is a valid legacy dt-binding.
Let's improve the logic to create a MDIO bus if either:
- Devicetree contains a MDIO bus
- !fixed-link && !phy-handle (legacy handling)
This way the case where no MDIO bus should be made is handled, as well
as retaining backwards compatibility with the valid cases.
Below devicetree snippets can be found that explain some of
the cases above more concretely.
Here's[0] a devicetree example where the MAC is both fixed-link and
driving a switch on MDIO (case "2" above). This needs a MDIO bus to
be created:
&fec1 {
phy-mode = "rmii";
fixed-link {
speed = <100>;
full-duplex;
};
mdio1: mdio {
switch0: switch0@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
};
};
};
Here's[1] an example where there is no MDIO bus or fixed-link for
the ethernet1 MAC, so no MDIO bus should be created since ethernet0
is the MDIO master for ethernet1's phy:
ðernet0 {
phy-mode = "sgmii";
phy-handle = <&sgmii_phy0>;
mdio {
compatible = "snps,dwmac-mdio";
sgmii_phy0: phy@8 {
compatible = "ethernet-phy-id0141.0dd4";
reg = <0x8>;
device_type = "ethernet-phy";
};
sgmii_phy1: phy@a {
compatible = "ethernet-phy-id0141.0dd4";
reg = <0xa>;
device_type = "ethernet-phy";
};
};
};
ðernet1 {
phy-mode = "sgmii";
phy-handle = <&sgmii_phy1>;
};
Finally there's descriptions like this[2] which don't describe the
MDIO bus but expect it to be created and the whole address space
scanned for a phy since there's no phy-handle or fixed-link described:
&gmac {
phy-supply = <&vcc_lan>;
phy-mode = "rmii";
snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
};
[0] https://elixir.bootlin.com/linux/v6.5-rc5/source/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
[1] https://elixir.bootlin.com/linux/v6.6-rc5/source/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
[2] https://elixir.bootlin.com/linux/v6.6-rc5/source/arch/arm64/boot/dts/rockchip/rk3368-r88.dts#L164
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/intel/iavf/iavf_ethtool.c
3a0b5a2929fd ("iavf: Introduce new state machines for flow director")
95260816b489 ("iavf: use iavf_schedule_aq_request() helper")
https://lore.kernel.org/all/84e12519-04dc-bd80-bc34-8cf50d7898ce@intel.com/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
c13e268c0768 ("bnxt_en: Fix HWTSTAMP_FILTER_ALL packet timestamp logic")
c2f8063309da ("bnxt_en: Refactor RX VLAN acceleration logic.")
a7445d69809f ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
1c7fd6ee2fe4 ("bnxt_en: Rename some macros for the P5 chips")
https://lore.kernel.org/all/20231211110022.27926ad9@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
bd6781c18cb5 ("bnxt_en: Fix wrong return value check in bnxt_close_nic()")
84793a499578 ("bnxt_en: Skip nic close/open when configuring tstamp filters")
https://lore.kernel.org/all/20231214113041.3a0c003c@canb.auug.org.au/
drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c
3d7a3f2612d7 ("net/mlx5: Nack sync reset request when HotPlug is enabled")
cecf44ea1a1f ("net/mlx5: Allow sync reset flow when BF MGT interface device is present")
https://lore.kernel.org/all/20231211110328.76c925af@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Many hardware configurations have the MDIO bus disabled, and are instead
using some other MDIO bus to talk to the MAC's phy.
of_mdiobus_register() returns -ENODEV in this case. Let's handle it
gracefully instead of failing to probe the MAC.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20231212-b4-stmmac-handle-mdio-enodev-v2-1-600171acf79f@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In 10M SGMII mode all the packets are being dropped due to wrong Rx clock.
SGMII 10MBPS mode needs RX clock divider programmed to avoid drops in Rx.
Update configure SGMII function with Rx clk divider programming.
Fixes: 463120c31c58 ("net: stmmac: dwmac-qcom-ethqos: add support for SGMII")
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20231212092208.22393-1-quic_snehshah@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device binds to proper PCI ID (LOONGSON, 0x7a03), already listed in DTS,
so checking for some other compatible does not make sense. It cannot be
bound to unsupported platform.
Drop useless, incorrect (space in between) and undocumented compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Generic code will use mdio. If it is not initialized before use,
the kernel will Oops.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Complete all counters on XGMAC Core.
These can be useful for debugging.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/stmicro/stmmac/dwmac5.c
drivers/net/ethernet/stmicro/stmmac/dwmac5.h
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
drivers/net/ethernet/stmicro/stmmac/hwif.h
37e4b8df27bc ("net: stmmac: fix FPE events losing")
c3f3b97238f6 ("net: stmmac: Refactor EST implementation")
https://lore.kernel.org/all/20231206110306.01e91114@canb.auug.org.au/
Adjacent changes:
net/ipv4/tcp_ao.c
9396c4ee93f9 ("net/tcp: Don't store TCP-AO maclen on reqsk")
7b0f570f879a ("tcp: Move TCP-AO bits from cookie_v[46]_check() to tcp_ao_syncookie().")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for cycle-time-extension. TER GCL-register needs to be
updated with the cycle-time-extension. Width of TER register is EST
time interval width + 7 bits.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-4-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor EST implementation by moving common code for DWMAC4 and
DWXGMAC IPs into a separate EST module. EST implementation for DWMAC4
and DWXGMAC differs only for CSR base address, PTOV field offset
width, and PTOV clock multiplier value.
Thanks, Serge Semin and Jakub Kicinski for the suggestions on
refactoring EST implementation into a separate EST module.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-3-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enabled the following EST related interrupts:
1) Constant Gate Control Error (CGCE)
2) Head-of-Line Blocking due to Scheduling (HLBS)
3) Head-of-Line Blocking due to Frame Size (HLBF)
4) Base Time Register error (BTRE)
5) Switch to S/W owned list Complete (SWLC)
Also, add EST errors into the ethtool statistic.
The commit e49aa315cb01 ("net: stmmac: EST interrupts handling and
error reporting") and commit 9f298959191b ("net: stmmac: Add EST
errors into ethtool statistic") add EST interrupts handling and error
reporting support to DWMAC4 core. This patch enables the same support
for XGMAC.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-2-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-11-30
We've added 30 non-merge commits during the last 7 day(s) which contain
a total of 58 files changed, 1598 insertions(+), 154 deletions(-).
The main changes are:
1) Add initial TX metadata implementation for AF_XDP with support in mlx5
and stmmac drivers. Two types of offloads are supported right now, that
is, TX timestamp and TX checksum offload, from Stanislav Fomichev with
stmmac implementation from Song Yoong Siang.
2) Change BPF verifier logic to validate global subprograms lazily instead
of unconditionally before the main program, so they can be guarded using
BPF CO-RE techniques, from Andrii Nakryiko.
3) Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter, from Jiri Olsa.
4) Use pkg-config in BPF selftests to determine ld flags which is
in particular needed for linking statically, from Akihiko Odaki.
5) Fix a few BPF selftest failures to adapt to the upcoming LLVM18,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (30 commits)
bpf/tests: Remove duplicate JSGT tests
selftests/bpf: Add TX side to xdp_hw_metadata
selftests/bpf: Convert xdp_hw_metadata to XDP_USE_NEED_WAKEUP
selftests/bpf: Add TX side to xdp_metadata
selftests/bpf: Add csum helpers
selftests/xsk: Support tx_metadata_len
xsk: Add option to calculate TX checksum in SW
xsk: Validate xsk_tx_metadata flags
xsk: Document tx_metadata_len layout
net: stmmac: Add Tx HWTS support to XDP ZC
net/mlx5e: Implement AF_XDP TX timestamp and checksum offload
tools: ynl: Print xsk-features from the sample
xsk: Add TX timestamp and TX checksum offload support
xsk: Support tx_metadata_len
selftests/bpf: Use pkg-config for libelf
selftests/bpf: Override PKG_CONFIG for static builds
selftests/bpf: Choose pkg-config for the target
bpftool: Add support to display uprobe_multi links
selftests/bpf: Add link_info test for uprobe_multi link
selftests/bpf: Use bpf_link__destroy in fill_link_info tests
...
====================
Conflicts:
Documentation/netlink/specs/netdev.yaml:
839ff60df3ab ("net: page_pool: add nlspec for basic access to page pools")
48eb03dd2630 ("xsk: Add TX timestamp and TX checksum offload support")
https://lore.kernel.org/all/20231201094705.1ee3cab8@canb.auug.org.au/
While at it also regen, tree is dirty after:
48eb03dd2630 ("xsk: Add TX timestamp and TX checksum offload support")
looks like code wasn't re-rendered after "render-max" was removed.
Link: https://lore.kernel.org/r/20231130145708.32573-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch enables transmit hardware timestamp support to XDP zero copy
via XDP Tx metadata framework.
This patchset is tested with tools/testing/selftests/bpf/xdp_hw_metadata
on Intel Tiger Lake platform. Below are the test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
sudo hwstamp_ctl -i <interface name> -t 1 -r 1
Command on Link Partner:
echo -n xdp | nc -u -q1 <destination IPv4 addr> 9091
Result:
xsk_ring_cons__peek: 1
0x55bbbf08b6d0: rx_desc[2]->addr=8c100 addr=8c100 comp_addr=8c100 EoP
No rx_hash err=-95
rx_timestamp: 1677762688429141540 (sec:1677762688.4291)
HW RX-time: 1677762688429141540 (sec:1677762688.4291) delta to User RX-time sec:0.0003 (250.665 usec)
XDP RX-time: 1677762688429375597 (sec:1677762688.4294) delta to User RX-time sec:0.0000 (16.608 usec)
0x55bbbf08b6d0: ping-pong with csum=561c (want f488) csum_start=34 csum_offset=6
0x55bbbf08b6d0: complete tx idx=2 addr=2008
tx_timestamp: 1677762688431127273 (sec:1677762688.4311)
HW TX-complete-time: 1677762688431127273 (sec:1677762688.4311) delta to User TX-complete-time sec:0.0083 (8331.655 usec)
XDP RX-time: 1677762688429375597 (sec:1677762688.4294) delta to User TX-complete-time sec:0.0101 (10083.331 usec)
HW RX-time: 1677762688429141540 (sec:1677762688.4291) delta to HW TX-complete-time sec:0.0020 (1985.733 usec)
0x55bbbf08b6d0: complete rx idx=130 addr=8c100
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20231127190319.1190813-6-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Commit aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/intel/ice/ice_main.c
c9663f79cd82 ("ice: adjust switchdev rebuild path")
7758017911a4 ("ice: restore timestamp configuration after device reset")
https://lore.kernel.org/all/20231121211259.3348630-1-anthony.l.nguyen@intel.com/
Adjacent changes:
kernel/bpf/verifier.c
bb124da69c47 ("bpf: keep track of max number of bpf_loop callback iterations")
5f99f312bd3b ("bpf: add register bounds sanity checks and sanitization")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current implementation supports driver level VLAN tag stripping only.
The features is always on if CONFIG_VLAN_8021Q is enabled in kernel
config and is not user configurable.
This patch add support to MAC level VLAN tag stripping and can be
configured through ethtool. If the rx-vlan-offload is off, the VLAN tag
will be stripped by driver. If the rx-vlan-offload is on, the VLAN tag
will be stripped by MAC.
Command: ethtool -K <interface> rx-vlan-offload off | on
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Signed-off-by: Gan, Yi Fang <yi.fang.gan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code to show extended descriptor is identical to normal one.
Consolidate the code to remove duplication.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/a2a5c5ce9338bdea60ec71d7eeb00fe757281557.1700372381.git.baruch@tkos.co.il
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
One newline per line should be enough. Reduce the verbosity of
descriptors dump.
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/444f3b1dd409fdb14ed2a1ae7679a86b110dadcd.1700372381.git.baruch@tkos.co.il
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dma_rx_size can be set as low as 64. Rx budget might be higher than
that. Make sure to not overrun allocated rx buffers when budget is
larger.
Leave one descriptor unused to avoid wrap around of 'dirty_rx' vs
'cur_rx'.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Link: https://lore.kernel.org/r/d95413e44c97d4692e72cec13a75f894abeb6998.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The while loop condition verifies 'count < limit'. Neither value change
before the 'count >= limit' check. As is this check is dead code. But
code inspection reveals a code path that modifies 'count' and then goto
'drain_data' and back to 'read_again'. So there is a need to verify
count value sanity after 'read_again'.
Move 'read_again' up to fix the count limit check.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/d9486296c3b6b12ab3a0515fcd47d56447a07bfc.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
From XGMAC Core 3.20 and later, each Flexible PPS has individual PPSEN bit
to select Fixed mode or Flexible mode. The PPSEN must be set, or it stays
in Fixed PPS mode by default.
XGMAC Core prior 3.20, only PPSEN0(bit 4) is writable. PPSEN{1,2,3} are
read-only reserved, and they are already in Flexible mode by default, our
new code always set PPSEN{1,2,3} do not make things worse ;-)
Fixes: 95eaf3cd0a90 ("net: stmmac: dwxgmac: Add Flexible PPS support")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/mac80211/rx.c
91535613b609 ("wifi: mac80211: don't drop all unprotected public action frames")
6c02fab72429 ("wifi: mac80211: split ieee80211_drop_unencrypted_mgmt() return value")
Adjacent changes:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c
61471264c018 ("net: ethernet: apm: Convert to platform remove callback returning void")
d2ca43f30611 ("net: xgene: Fix unused xgene_enet_of_match warning for !CONFIG_OF")
net/vmw_vsock/virtio_transport.c
64c99d2d6ada ("vsock/virtio: support to send non-linear skb")
53b08c498515 ("vsock/virtio: initialize the_virtio_vsock before using VQs")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Upon boot up, the driver will configure the MAC capabilities based on
the maximum number of tx and rx queues. When the user changes the
tx queues to single queue, the MAC should be capable of supporting Half
Duplex, but the driver does not update the MAC capabilities when it is
configured so.
Using the stmmac_reinit_queues() to check the number of tx queues
and set the MAC capabilities accordingly.
Fixes: 0366f7e06a6b ("net: stmmac: add ethtool support for get/set channels")
Cc: <stable@vger.kernel.org> # 5.17+
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Gan, Yi Fang <yi.fang.gan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8fce33317023 ("net: stmmac: Rework coalesce timer and fix
multi-queue races") decreased the TX coalesce timer from 40ms to 1ms.
This caused some performance regression on some target (regression was
reported at least on ipq806x) in the order of 600mbps dropping from
gigabit handling to only 200mbps.
The problem was identified in the TX timer getting armed too much time.
While this was fixed and improved in another commit, performance can be
improved even further by increasing the timer delay a bit moving from
1ms to 5ms.
The value is a good balance between battery saving by prevending too
much interrupt to be generated and permitting good performance for
internet oriented devices.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
