summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2019-04-12nfp: split out common control message handling codeJakub Kicinski
BPF's control message handler seems like a good base to built on for request-reply control messages. Split it out to allow for reuse. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-12nfp: move vNIC reset before netdev initJakub Kicinski
During probe we clear vNIC configuration in case the device wasn't closed cleanly by previous driver. Move that code before netdev init, so netdev init can already try to apply its config parameters. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-12nfp: add a mutex lock for the vNIC ctrl BARJakub Kicinski
Soon we will try to write to the vNIC mailbox without RTNL held. Add a new mutex to protect access to specific parts of the PCI control BAR. Move the mailbox size checking to the mailbox lock() helper, where it can be more effective (happen prior to potential overwrite of other data). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-12nfp: opportunistically poll for reconfig resultDirk van der Merwe
If the reconfig was a quick update, we could have results available from firmware within 200us. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2019-04-08bnxt_en: Reset device on RX buffer errors.Michael Chan
If the RX completion indicates RX buffers errors, the RX ring will be disabled by firmware and no packets will be received on that ring from that point on. Recover by resetting the device. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08bnxt_en: Improve RX consumer index validity check.Michael Chan
There is logic to check that the RX/TPA consumer index is the expected index to work around a hardware problem. However, the potentially bad consumer index is first used to index into an array to reference an entry. This can potentially crash if the bad consumer index is beyond legal range. Improve the logic to use the consumer index for dereferencing after the validity check and log an error message. Fixes: fa7e28127a5a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: macb driver, check for SKBTX_HW_TSTAMPPaul Thomas
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been enabled for this skb. It does fix the issue where normal socks that aren't expecting a timestamp will not wake up on select, but when a user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work. Signed-off-by: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08ethtool: thunder_bgx: use ethtool.h constants for speed and duplexMichael Zhivich
Use constants provided by ethtool.h for speed and duplex values instead of raw integer constants to increase code readability. thunder_bgx already uses SPEED_UNKNOWN and DUPLEX_UNKNOWN constants, also provided by ethtool.h. Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constantMichael Zhivich
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant, which is defined as -1, resulting in value truncation and thus incorrect test results against SPEED_UNKNOWN. For example, the following test will print "False": u16 speed = SPEED_UNKNOWN; if (speed == SPEED_UNKNOWN) printf("True"); else printf("False"); Change storage of speed to use u32 to avoid this issue. Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constantMichael Zhivich
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant, which is defined as -1, resulting in value truncation and thus incorrect test results against SPEED_UNKNOWN. For example, the following test will print "False": u16 speed = SPEED_UNKNOWN; if (speed == SPEED_UNKNOWN) printf("True"); else printf("False"); Change storage of speed to use u32 to avoid this issue. Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08mlxsw: core: Add support for devlink info commandShalom Toledo
Expose the following ASIC information via devlink info command: - Driver name - Hardware revision - Firmware PSID - Running firmware version Standard output example: $ devlink dev info pci/0000:03:00.0 pci/0000:03:00.0: driver mlxsw_spectrum versions: fixed: hw.revision A0 fw.psid MT_2750110033 running: fw.version 13.1910.622 Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08mlxsw: reg: Add MGIR registerShalom Toledo
Add MGIR register. MGIR, Management General Information Register, allows software to query the hardware and firmware general information. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: fix keep_alive_timer not stop problemHuazhong Tan
When hclgevf_client_start() fails or VF driver unloaded, there is nobody to disable keep_alive_timer. So this patch fixes them. Fixes: a6d818e31d08 ("net: hns3: Add vport alive state checking support") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: remove resetting check in hclgevf_reset_task_scheduleHuazhong Tan
The checking of HCLGEVF_STATE_RST_HANDLING flag in the hclgevf_reset_task_schedule() will make some scheduling of reset pending fail. This flag will be checked in the hclgevf_reset_service_task(), it is unnecessary to check it in the hclgevf_reset_task_schedule(). So this patch removes it. Fixes: 35a1e50343bd ("net: hns3: Add VF Reset Service Task to support event handling") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: add error handler for initializing command queueHuazhong Tan
This patch adds error handler for the failure of command queue initialization both PF and VF. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: stop mailbox handling when command queue need re-initHuazhong Tan
If the command queue needs re-initialization, the mailbox handling task should do nothing, otherwise this task will just get some error print. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: handle pending reset while reset failHuazhong Tan
The ongoing lower-level reset will fail when there is a higher-level reset occurs, so the error handler should deal with this situation. Fixes: 6a5f6fa382f3 ("net: hns3: add error handler for hclgevf_reset()") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: do not request reset when hardware resettingHuazhong Tan
When hardware reset does not finish, the driver should not request a new reset, otherwise the ongoing hardware reset will get problem. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: ignore lower-level new coming resetHuazhong Tan
It is unnecessary to deal with the new coming reset if it is lower than the ongoing one. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: deactive the reset timer when reset successfullyHuazhong Tan
If the reset has been done successfully, the ongoing reset timer is unnecessary. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: adjust the timing of hns3_client_stop when unloadingHuazhong Tan
hns3_client_stop() should be called after unregister_netdev(), otherwise the ongoing reset task may start the client just after it. Fixes: a6d818e31d08 ("net: hns3: Add vport alive state checking support") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: not reset vport who not alive when PF resetHuazhong Tan
If a vport is not alive, it is unnecessary to notify it to reset before PF asserting a reset. So before inform vport to reset, we need to check its alive state firstly. Fixes: aa5c4f175be6 ("net: hns3: add reset handling for VF when doing PF reset") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: set up the vport alive state while reinitializingHuazhong Tan
When reinitializing, the vport alive state needs to be set up. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: hns3: set vport alive state to default while resettingHuazhong Tan
When resetting, the vport alive state should be set to default, otherwise the alive state of the vport whose driver not running is wrong before the timer to check it out. Fixes: a6d818e31d08 ("net: hns3: Add vport alive state checking support") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08ipv4: Flag fib_info with a fib_nh using IPv6 gatewayDavid Ahern
Until support is added to the offload drivers, they need to be able to reject routes with an IPv6 gateway. To that end add a flag to fib_info that indicates if any fib_nh has a v6 gateway. The flag allows the drivers to efficiently know the use of a v6 gateway without walking all fib_nh tied to a fib_info each time a route is added. Update mlxsw and rocker to reject the routes with extack message as to why. Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08ipv4: Add support to rtable for ipv6 gatewayDavid Ahern
Add support for an IPv6 gateway to rtable. Since a gateway is either IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides which address is in use. When dumping the route data, encode an ipv6 nexthop using RTA_VIA. Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08ipv4: Prepare rtable for IPv6 gatewayDavid Ahern
To allow the gateway to be either an IPv4 or IPv6 address, remove rt_uses_gateway from rtable and replace with rt_gw_family. If rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway to rt_gw4 to represent the IPv4 version. Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: Replace nhc_has_gw with nhc_gw_familyDavid Ahern
Allow the gateway in a fib_nh_common to be from a different address family than the outer fib{6}_nh. To that end, replace nhc_has_gw with nhc_gw_family and update users of nhc_has_gw to check nhc_gw_family. Now nhc_family is used to know if the nh_common is part of a fib_nh or fib6_nh (used for container_of to get to route family specific data), and nhc_gw_family represents the address family for the gateway. Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08r8169: disable ASPM againHeiner Kallweit
There's a significant number of reports that re-enabling ASPM causes different issues, ranging from decreased performance to system not booting at all. This affects only a minority of users, but the number of affected users is big enough that we better switch off ASPM again. This will hurt notebook users who are not affected by the issues, they may see decreased battery runtime w/o ASPM. With the PCI core folks is being discussed to add generic sysfs attributes to control ASPM. Once this is in place brave enough users can re-enable ASPM on their system. Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08Merge tag 'mlx5-updates-2019-04-02' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mamameed says: ==================== mlx5-updates-2019-04-02 This series provides misc updates to mlx5 driver 1) Aya Levin (1): Handle event of power detection in the PCIE slot 2) Eli Britstein (6): Some TC VLAN related updates and fixes to the previous VLAN modify action support patchset. Offload TC e-switch rules with egress/ingress VLAN devices 3) Max Gurtovoy (1): Fix double mutex initialization in esiwtch.c 4) Tariq Toukan (3): Misc small updates A write memory barrier is sufficient in EQ ci update Obsolete param field holding a constant value Unify logic of MTU boundaries 5) Tonghao Zhang (4): Misc updates to en_tc.c Make the log friendly when decapsulation offload not supported Remove 'parse_attr' argument in parse_tc_fdb_actions() Deletes unnecessary setting of esw_attr->parse_attr Return -EOPNOTSUPP when attempting to offload an unsupported action ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08cxgb4: Don't return EAGAIN when TCAM is full.Vishal Kulkarni
During hash filter programming, driver needs to return ENOSPC error intead of EAGAIN when TCAM is full. Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: xilinx: emaclite: add minimal ndo_do_ioctl hookAlexandru Ardelean
This hook only implements a minimal set of ioctl hooks to be able to access MII regs by using phytool. When using this simple MAC controller, it's pretty difficult to do debugging of the PHY chip without checking MII regs. Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-08net: xilinx: emaclite: add minimal ethtool opsAlexandru Ardelean
This set adds a minimal set of ethtool hooks to the driver, which provide a decent amount of link information via ethtool. With this change, running `ethtool ethX` in user-space provides all the neatly-formatted information about the link (what was negotiated, what is advertised, etc). Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-06net: hns: fix unsigned comparison to less than zeroColin Ian King
Currently mskid is unsigned and hence comparisons with negative error return values are always false. Fix this by making mskid an int. Fixes: f058e46855dc ("net: hns: fix ICMP6 neighbor solicitation messages discard problem") Addresses-Coverity: ("Operands don't affect result") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-06r8169: disable tx interrupt coalescing on RTL8168Heiner Kallweit
In contrast to switching rx irq coalescing off what fixed an issue, switching tx irq coalescing off is merely a latency optimization, therefore net-next. As part of this change: - Remove INTT_0 .. INTT_3 constants, they aren't used. - Remove comment in rtl_hw_start_8169(), we now have a detailed description by the code in rtl_set_coalesce(). - Due to switching irq coalescing off per default we don't need the initialization in rtl_hw_start_8168(). If ethtool is used to switch on coalescing then rtl_set_coalesce() will configure this register. For the sake of completeness: This patch just changes the default. Users still have the option to configure irq coalescing via ethtool. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Minor comment merge conflict in mlx5. Staging driver has a fixup due to the skb->xmit_more changes in 'net-next', but was removed in 'net'. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-05net/mlx5e: Unify logic of MTU boundariesTariq Toukan
Expose a new helper that wraps the logic for setting the netdevice's MTU boundaries. Use it for the different components (Eth, rep, IPoIB). Set the netdevice min MTU to ETH_MIN_MTU, and the max according to both the FW capability and the kernel definition. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Obsolete param field holding a constant valueTariq Toukan
The LRO WQE size is a constant, obsolete the parameter field that holds it. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5: A write memory barrier is sufficient in EQ ci updateTariq Toukan
Soften the memory barrier call of mb() by a sufficient wmb() in the consumer index update of the event queues. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Do not rewrite fields with the same matchEli Britstein
If we have a match for the same value of a rewrite field, there is no point for the rewrite. In order to save rewrite actions, and avoid entirely rewrite actions (if all rewrites are the same), ignore such rewrite fields. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Offload TC e-switch rules with ingress VLAN deviceEli Britstein
Offload TC rule on a VLAN device by matching the VLAN properties of the VLAN device and emulating vlan pop actions. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Offload TC e-switch rules with egress VLAN deviceEli Britstein
Upon redirection to an uplink VLAN device, emulate vlan push actions according to the VLAN properties of the VLAN device and redirect to the uplink. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Allow VLAN rewrite of prio field with the same matchEli Britstein
Changing the prio field of the VLAN is not supported. With commit 37410902874c ("net/mlx5e: Support VLAN modify action") zero value indicated "no-change". Allow the vid rewrite if the prio match is the same as the prio set value. Fixes: 37410902874c ("net/mlx5e: Support VLAN modify action") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Deny VLAN rewrite if there is no VLAN header matchEli Britstein
Rewrite of the packet in the VLAN offset may corrupt the packet if it's not VLAN tagged. Deny the rewrite in this case. Fixes: 37410902874c ("net/mlx5e: Support VLAN modify action") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Use helpers to get headers criteria and value pointersEli Britstein
The headers criteria and value pointers may be either of the inner packet, if a tunnel exists, or of the outer. Simplify the code by using helper functions to retrieve them. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Return -EOPNOTSUPP when attempting to offload an unsupported actionTonghao Zhang
* Now the encapsulation is not supported for mlx5 VFs. When we try to offload that action, the -EINVAL is returned, but not -EOPNOTSUPP. This patch changes the returned value and ignore to confuse user. The command is shown as below [1]. * When max modify header action is zero, we return -EOPNOTSUPP directly. In this way, we can ignore wrong message info (e.g. "mlx5: parsed 0 pedit actions, can't do more"). This happens when offloading pedit actions on mlx(cx4) VFs. The command is shown as below [2]. For example: (p2p1_0 is VF net device) [1] $ tc filter add dev p2p1_0 protocol ip parent ffff: prio 1 flower skip_sw \ src_mac e4:11:22:33:44:01 \ action tunnel_key set \ src_ip 1.1.1.100 \ dst_ip 1.1.1.200 \ dst_port 4789 id 100 \ action mirred egress redirect dev vxlan0 [2] $ tc filter add dev p2p1_0 parent ffff: protocol ip prio 1 \ flower skip_sw dst_mac 00:10:56:fb:64:e8 \ dst_ip 1.1.1.100 src_ip 1.1.1.200 \ action pedit ex munge eth src set 00:10:56:b4:5d:20 Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Deletes unnecessary setting of esw_attr->parse_attrTonghao Zhang
This patch deletes unnecessary setting of the esw_attr->parse_attr to parse_attr in parse_tc_fdb_actions() because it is already done by the mlx5e_flow_esw_attr_init() function. Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Remove 'parse_attr' argument in parse_tc_fdb_actions()Tonghao Zhang
This patch is a little improvement. Simplify the parse_tc_fdb_actions(). Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-05net/mlx5e: Make the log friendly when decapsulation offload not supportedTonghao Zhang
If we try to offload decapsulation actions to VFs hw, we get the log [1]. It's not friendly, because the kind of net device is null, and we don't know what '0' means. [1] "mlx5_core 0000:05:01.2 vf_0: decapsulation offload is not supported for net device (0)" Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
generated by cgit (git 2.34.1) at 2025-04-18 23:30:35 +0000