summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2021-08-19net: dpaa2-switch: disable the control interface on error pathVladimir Oltean
Currently dpaa2_switch_takedown has a funny name and does not do the opposite of dpaa2_switch_init, which makes probing fail when we need to handle an -EPROBE_DEFER. A sketch of what dpaa2_switch_init does: dpsw_open dpaa2_switch_detect_features dpsw_reset for (i = 0; i < ethsw->sw_attr.num_ifs; i++) { dpsw_if_disable dpsw_if_set_stp dpsw_vlan_remove_if_untagged dpsw_if_set_tci dpsw_vlan_remove_if } dpsw_vlan_remove alloc_ordered_workqueue dpsw_fdb_remove dpaa2_switch_ctrl_if_setup When dpaa2_switch_takedown is called from the error path of dpaa2_switch_probe(), the control interface, enabled by dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled, because dpaa2_switch_takedown does not call dpaa2_switch_ctrl_if_teardown. Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this means that a second probe of the driver will happen with the control interface directly enabled. This will trigger a second error: [ 93.273528] fsl_dpaa2_switch dpsw.0: dpsw_ctrl_if_set_pools() failed [ 93.281966] fsl_dpaa2_switch dpsw.0: fsl_mc_driver_probe failed: -13 [ 93.288323] fsl_dpaa2_switch: probe of dpsw.0 failed with error -13 Which if we investigate the /dev/dpaa2_mc_console log, we find out is caused by: [E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in reasonable limits, no reason to change STP state, re-add VLANs etc), and rename it to something more conventional, like dpaa2_switch_teardown. Fixes: 613c0a5810b7 ("staging: dpaa2-switch: enable the control interface") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-19iavf: Fix ping is lost after untrusted VF had tried to change MACSylwester Dziedziuch
Make changes to MAC address dependent on the response of PF. Disallow changes to HW MAC address and MAC filter from untrusted VF, thanks to that ping is not lost if VF tries to change MAC. Add a new field in iavf_mac_filter, to indicate whether there was response from PF for given filter. Based on this field pass or discard the filter. If untrusted VF tried to change it's address, it's not changed. Still filter was changed, because of that ping couldn't go through. Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan G <Gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-19i40e: Fix ATR queue selectionArkadiusz Kubalewski
Without this patch, ATR does not work. Receive/transmit uses queue selection based on SW DCB hashing method. If traffic classes are not configured for PF, then use netdev_pick_tx function for selecting queue for packet transmission. Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx, which ensures that packet is transmitted/received from CPU that is running the application. Reproduction steps: 1. Load i40e driver 2. Map each MSI interrupt of i40e port for each CPU 3. Disable ntuple, enable ATR i.e.: ethtool -K $interface ntuple off ethtool --set-priv-flags $interface flow-director-atr 4. Run application that is generating traffic and is bound to a single CPU, i.e.: taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10 5. Observe behavior: Application's traffic should be restricted to the CPU provided in taskset. Fixes: 89ec1f0886c1 ("i40e: Fix queue-to-TC mapping on Tx") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-18net: mscc: ocelot: allow forwarding from bridge ports to the tag_8021q CPU portVladimir Oltean
Currently we are unable to ping a bridge on top of a felix switch which uses the ocelot-8021q tagger. The packets are dropped on the ingress of the user port and the 'drop_local' counter increments (the counter which denotes drops due to no valid destinations). Dumping the PGID tables, it becomes clear that the PGID_SRC of the user port is zero, so it has no valid destinations. But looking at the code, the cpu_fwd_mask (the bit mask of DSA tag_8021q ports) is clearly missing from the forwarding mask of ports that are under a bridge. So this has always been broken. Looking at the version history of the patch, in v7 https://patchwork.kernel.org/project/netdevbpf/patch/20210125220333.1004365-12-olteanv@gmail.com/ the code looked like this: /* Standalone ports forward only to DSA tag_8021q CPU ports */ unsigned long mask = cpu_fwd_mask; (...) } else if (ocelot->bridge_fwd_mask & BIT(port)) { mask |= ocelot->bridge_fwd_mask & ~BIT(port); while in v8 (the merged version) https://patchwork.kernel.org/project/netdevbpf/patch/20210129010009.3959398-12-olteanv@gmail.com/ it looked like this: unsigned long mask; (...) } else if (ocelot->bridge_fwd_mask & BIT(port)) { mask = ocelot->bridge_fwd_mask & ~BIT(port); So the breakage was introduced between v7 and v8 of the patch. Fixes: e21268efbe26 ("net: dsa: felix: perform switch setup for tag_8021q") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210817160425.3702809-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-17ixgbe, xsk: clean up the resources in ixgbe_xsk_pool_enable error pathWang Hai
In ixgbe_xsk_pool_enable(), if ixgbe_xsk_wakeup() fails, We should restore the previous state and clean up the resources. Add the missing clear af_xdp_zc_qps and unmap dma to fix this bug. Fixes: d49e286d354e ("ixgbe: add tracking of AF_XDP zero-copy state for each queue pair") Fixes: 4a9b32f30f80 ("ixgbe: fix potential RX buffer starvation for AF_XDP") Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210817203736.3529939-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-17net: qlcnic: add missed unlock in qlcnic_83xx_flash_read32Dinghao Liu
qlcnic_83xx_unlock_flash() is called on all paths after we call qlcnic_83xx_lock_flash(), except for one error path on failure of QLCRD32(), which may cause a deadlock. This bug is suggested by a static analysis tool, please advise. Fixes: 81d0aeb0a4fff ("qlcnic: flash template based firmware reset recovery") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-16bnxt_en: Add missing DMA memory barriersMichael Chan
Each completion ring entry has a valid bit to indicate that the entry contains a valid completion event. The driver's main poll loop __bnxt_poll_work() has the proper dma_rmb() to make sure the valid bit of the next entry has been checked before proceeding further. But when we call bnxt_rx_pkt() to process the RX event, the RX completion event consists of two completion entries and only the first entry has been checked to be valid. We need the same barrier after checking the next completion entry. Add missing dma_rmb() barriers in bnxt_rx_pkt() and other similar locations. Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.") Reported-by: Lance Richardson <lance.richardson@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Lance Richardson <lance.richardson@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16bnxt_en: Disable aRFS if running on 212 firmwareMichael Chan
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple filters are inserted and deleted by the 212 firmware. Fixes: ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16qed: Fix null-pointer dereference in qed_rdma_create_qp()Shai Malin
Fix a possible null-pointer dereference in qed_rdma_create_qp(). Changes from V2: - Revert checkpatch fixes. Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16qed: qed ll2 race condition fixesShai Malin
Avoiding qed ll2 race condition and NULL pointer dereference as part of the remove and recovery flows. Changes form V1: - Change (!p_rx->set_prod_addr). - qed_ll2.c checkpatch fixes. Change from V2: - Revert "qed_ll2.c checkpatch fixes". Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-13ice: Fix perout start time roundingMaciej Machnikowski
Internal tests found out that the latest code doesn't bring up 1PPS out as expected. As a result of incorrect define used to round the time up the time was round down to the past second boundary. Fix define used for rounding to properly round up to the next Top of second in ice_ptp_cfg_clkout to fix it. Fixes: 172db5f91d5f ("ice: add support for auxiliary input/output pins") Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210813165018.2196013-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: count Tx dropsJakub Kicinski
Drivers should count packets they are dropping. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: make sure xmit_more + errors does not miss doorbellsJakub Kicinski
skbs are freed on error and not put on the ring. We may, however, be in a situation where we're freeing the last skb of a batch, and there is a doorbell ring pending because of xmit_more() being true earlier. Make sure we ring the door bell in such situations. Since errors are rare don't pay attention to xmit_more() and just always flush the pending frames. The busy case should be safe to be left alone because it can only happen if start_xmit races with completions and they both enable the queue. In that case the kick can't be pending. Noticed while reading the code. Fixes: 4d172f21cefe ("bnxt_en: Implement xmit_more.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: disable napi before canceling DIMJakub Kicinski
napi schedules DIM, napi has to be disabled first, then DIM canceled. Noticed while reading the code. Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown") Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: don't lock the tx queue from napi pollJakub Kicinski
We can't take the tx lock from the napi poll routine, because netpoll can poll napi at any moment, including with the tx lock already held. The tx lock is protecting against two paths - the disable path, and (as Michael points out) the NETDEV_TX_BUSY case which may occur if NAPI completions race with start_xmit and both decide to re-enable the queue. For the disable/ifdown path use synchronize_net() to make sure closing the device does not race we restarting the queues. Annotate accesses to dev_state against data races. For the NAPI cleanup vs start_xmit path - appropriate barriers are already in place in the main spot where Tx queue is stopped but we need to do the same careful dance in the TX_BUSY case. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-12net: mscc: Fix non-GPL export of regmap APIsMark Brown
The ocelot driver makes use of regmap, wrapping it with driver specific operations that are thin wrappers around the core regmap APIs. These are exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap exports which is frowned upon. Add _GPL suffixes to at least the APIs that are doing register I/O. Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted ↵Vladimir Oltean
by drivers towards the bridge The blamed commit added a new field to struct switchdev_notifier_fdb_info, but did not make sure that all call paths set it to something valid. For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE notifier, and since the 'is_local' flag is not set, it contains junk from the stack, so the bridge might interpret those notifications as being for local FDB entries when that was not intended. To avoid that now and in the future, zero-initialize all switchdev_notifier_fdb_info structures created by drivers such that all newly added fields to not need to touch drivers again. Fixes: 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-10Merge tag 'mlx5-fixes-2021-08-09' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2021-08-09 This series introduces fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-09net/mlx5: Fix return value from tracer initializationAya Levin
Check return value of mlx5_fw_tracer_start(), set error path and fix return value of mlx5_fw_tracer_init() accordingly. Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Synchronize correct IRQ when destroying CQShay Drory
The CQ destroy is performed based on the IRQ number that is stored in cq->irqn. That number wasn't set explicitly during CQ creation and as expected some of the API users of mlx5_core_create_cq() forgot to update it. This caused to wrong synchronization call of the wrong IRQ with a number 0 instead of the real one. As a fix, set the IRQ number directly in the mlx5_core_create_cq() and update all users accordingly. Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices") Fixes: ef1659ade359 ("IB/mlx5: Add DEVX support for CQ events") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5e: TC, Fix error handling memory leakChris Mi
Free the offload sample action on error. Fixes: f94d6389f6a8 ("net/mlx5e: TC, Add support to offload sample action") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Destroy pool->mutexShay Drory
Destroy pool->mutex when we destroy the pool. Fixes: c36326d38d93 ("net/mlx5: Round-Robin EQs over IRQs") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Set all field of mlx5_irq before inserting it to the xarrayShay Drory
Currently irq->pool is set after the irq is insert to the xarray. Set irq->pool before the irq is inserted to the xarray. Fixes: 71e084e26414 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Fix order of functions in mlx5_irq_detach_nb()Shay Drory
Change order of functions in mlx5_irq_detach_nb() so it will be a mirror of mlx5_irq_attach_nb. Fixes: 71e084e26414 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Block switchdev mode while devlink traps are activeAya Levin
Since switchdev mode can't support devlink traps, verify there are no active devlink traps before moving eswitch to switchdev mode. If there are active traps, prevent the switchdev mode configuration. Fixes: eb3862a0525d ("net/mlx5e: Enable traps according to link state") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5e: Destroy page pool after XDP SQ to fix use-after-freeMaxim Mikityanskiy
mlx5e_close_xdpsq does the cleanup: it calls mlx5e_free_xdpsq_descs to free the outstanding descriptors, which relies on mlx5e_page_release_dynamic and page_pool_release_page. However, page_pool_destroy is already called by this point, because mlx5e_close_rq runs before mlx5e_close_xdpsq. This commit fixes the use-after-free by swapping mlx5e_close_xdpsq and mlx5e_close_rq. The commit cited below started calling page_pool_destroy directly from the driver. Previously, the page pool was destroyed under a call_rcu from xdp_rxq_info_unreg_mem_model, which would defer the deallocation until after the XDPSQ is cleaned up. Fixes: 1da4bbeffe41 ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Bridge, fix ageing timeVlad Buslov
Ageing time is not converted from clock_t to jiffies which results incorrect ageing timeout calculation in workqueue update task. Fix it by applying clock_t_to_jiffies() to provided value. Fixes: c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5e: Avoid creating tunnel headers for local routeRoi Dayan
It could be local and remote are on the same machine and the route result will be a local route which will result in creating encap id with src/dst mac address of 0. Fixes: a54e20b4fcae ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: DR, Add fail on error check on decapAlex Vesker
While processing encapsulated packet on RX, one of the fields that is checked is the inner packet length. If the length as specified in the header doesn't match the actual inner packet length, the packet is invalid and should be dropped. However, such packet caused the NIC to hang. This patch turns on a 'fail_on_error' HW bit which allows HW to drop such an invalid packet while processing RX packet and trying to decap it. Fixes: ad17dc8cf910 ("net/mlx5: DR, Move STEv0 action apply logic") Signed-off-by: Alex Vesker <valex@nvidia.com> Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Don't skip subfunction cleanup in case of error in module initLeon Romanovsky
Clean SF resources if mlx5 eth failed to initialize. Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09iavf: Set RSS LUT and key in reset handle pathMd Fahad Iqbal Polash
iavf driver should set RSS LUT and key unconditionally in reset path. Currently, the driver does not do that. This patch fixes this issue. Fixes: 2c86ac3c7079 ("i40evf: create a generic config RSS function") Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-08-09ice: don't remove netdev->dev_addr from uc sync listBrett Creeley
In some circumstances, such as with bridging, it's possible that the stack will add the device's own MAC address to its unicast address list. If, later, the stack deletes this address, the driver will receive a request to remove this address. The driver stores its current MAC address as part of the VSI MAC filter list instead of separately. So, this causes a problem when the device's MAC address is deleted unexpectedly, which results in traffic failure in some cases. The following configuration steps will reproduce the previously mentioned problem: > ip link set eth0 up > ip link add dev br0 type bridge > ip link set br0 up > ip addr flush dev eth0 > ip link set eth0 master br0 > echo 1 > /sys/class/net/br0/bridge/vlan_filtering > modprobe -r veth > modprobe -r bridge > ip addr add 192.168.1.100/24 dev eth0 The following ping command fails due to the netdev->dev_addr being deleted when removing the bridge module. > ping <link partner> Fix this by making sure to not delete the netdev->dev_addr during MAC address sync. After fixing this issue it was noticed that the netdev_warn() in .set_mac was overly verbose, so make it at netdev_dbg(). Also, there is a possibility of a race condition between .set_mac and .set_rx_mode. Fix this by calling netif_addr_lock_bh() and netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr is going to be updated in .set_mac. Fixes: e94d44786693 ("ice: Implement filter sync, NDO operations and bump version") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Liang Li <liali@redhat.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-08-09ice: Stop processing VF messages during teardownAnirudh Venkataramanan
When VFs are setup and torn down in quick succession, it is possible that a VF is torn down by the PF while the VF's virtchnl requests are still in the PF's mailbox ring. Processing the VF's virtchnl request when the VF itself doesn't exist results in undefined behavior. Fix this by adding a check to stop processing virtchnl requests when VF teardown is in progress. Fixes: ddf30f7ff840 ("ice: Add handler to configure SR-IOV") Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-08-09ice: Prevent probing virtual functionsAnirudh Venkataramanan
The userspace utility "driverctl" can be used to change/override the system's default driver choices. This is useful in some situations (buggy driver, old driver missing a device ID, trying a workaround, etc.) where the user needs to load a different driver. However, this is also prone to user error, where a driver is mapped to a device it's not designed to drive. For example, if the ice driver is mapped to driver iavf devices, the ice driver crashes. Add a check to return an error if the ice driver is being used to probe a virtual function. Fixes: 837f08fdecbe ("ice: Add basic driver framework for Intel(R) E800 Series") Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-08-09net: ethernet: ti: cpsw: fix min eth packet size for non-switch use-casesGrygorii Strashko
The CPSW switchdev driver inherited fix from commit 9421c9015047 ("net: ethernet: ti: cpsw: fix min eth packet size") which changes min TX packet size to 64bytes (VLAN_ETH_ZLEN, excluding ETH_FCS). It was done to fix HW packed drop issue when packets are sent from Host to the port with PVID and un-tagging enabled. Unfortunately this breaks some other non-switch specific use-cases, like: - [1] CPSW port as DSA CPU port with DSA-tag applied at the end of the packet - [2] Some industrial protocols, which expects min TX packet size 60Bytes (excluding FCS). Fix it by configuring min TX packet size depending on driver mode - 60Bytes (ETH_ZLEN) for multi mac (dual-mac) mode - 64Bytes (VLAN_ETH_ZLEN) for switch mode and update it during driver mode change and annotate with READ_ONCE()/WRITE_ONCE() as it can be read by napi while writing. [1] https://lore.kernel.org/netdev/20210531124051.GA15218@cephalopod/ [2] https://e2e.ti.com/support/arm/sitara_arm/f/791/t/701669 Cc: stable@vger.kernel.org Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Reported-by: Ben Hutchings <ben.hutchings@essensium.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-08bnxt_en: Use register window 6 instead of 5 to read the PHCMichael Chan
Some older Broadcom debug tools use window 5 and may conflict, so switch to use window 6 instead. Fixes: 118612d519d8 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods") Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-08bnxt_en: Update firmware call to retrieve TX PTP timestampMichael Chan
New firmware interface requires the PTP sequence ID header offset to be passed to the firmware to properly find the matching timestamp for all protocols. Fixes: 83bb623c968e ("bnxt_en: Transmit and retrieve packet timestamps") Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-08bnxt_en: Update firmware interface to 1.10.2.52Michael Chan
The key change is the firmware call to retrieve the PTP TX timestamp. The header offset for the PTP sequence number field is now added. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-07r8169: change the L0/L1 entrance latencies for RTL8106eHayes Wang
The original L0 and L1 entrance latencies of RTL8106e are 4us. And they cause the delay of link-up interrupt when enabling ASPM. Change the L0 entrance latency to 7us and L1 entrance latency to 32us. Then, they could avoid the issue. Tested-by: Koba Ko <koba.ko@canonical.com> Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-07Revert "r8169: avoid link-up interrupt issue on RTL8106e if user enables ASPM"Hayes Wang
This reverts commit 1ee8856de82faec9bc8bd0f2308a7f27e30ba207. This is used to re-enable ASPM on RTL8106e, if it is possible. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-06net: mvvp2: fix short frame size on s390John Hubbard
On s390, the following build warning occurs: drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in conversion from 'long unsigned int' to 'int' changes value from '18446744073709551584' to '-32' [-Woverflow] 844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE) This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is already 64-byte aligned) on some architectures, actually gets ALIGN'd up to 512 bytes in the s390 case. So then, when this is invoked: MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE) ...that turns into: 704 - 224 - 512 == -32 ...which is not a good frame size to end up with! The warning above is a bit lucky: it notices a signed/unsigned bad behavior here, which leads to the real problem of a frame that is too short for its contents. Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is just exactly big enough. (The other values can't readily be changed without causing a lot of other problems.) Fixes: 07dd0a7aae7f ("mvpp2: add basic XDP support") Cc: Sven Auhagen <sven.auhagen@voleatech.de> Cc: Matteo Croce <mcroce@microsoft.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-05net: vxge: fix use-after-free in vxge_device_unregisterPavel Skripkin
Smatch says: drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev); drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev); drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev); drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev); Since vdev pointer is netdev private data accessing it after free_netdev() call can cause use-after-free bug. Fix it by moving free_netdev() call at the end of the function Fixes: 6cca200362b4 ("vxge: cleanup probe error paths") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-05net: fec: fix use-after-free in fec_drv_removePavel Skripkin
Smatch says: drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev); drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev); Since fep pointer is netdev private data, accessing it after free_netdev() call can cause use-after-free bug. Fix it by moving free_netdev() call at the end of the function Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: a31eda65ba21 ("net: fec: fix clock count mis-match") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-05net: ethernet: ti: am65-cpsw: fix crash in ↵Grygorii Strashko
am65_cpsw_port_offload_fwd_mark_update() The am65_cpsw_port_offload_fwd_mark_update() causes NULL exception crash when there is at least one disabled port and any other port added to the bridge first time. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000858 pc : am65_cpsw_port_offload_fwd_mark_update+0x54/0x68 lr : am65_cpsw_netdevice_event+0x8c/0xf0 Call trace: am65_cpsw_port_offload_fwd_mark_update+0x54/0x68 notifier_call_chain+0x54/0x98 raw_notifier_call_chain+0x14/0x20 call_netdevice_notifiers_info+0x34/0x78 __netdev_upper_dev_link+0x1c8/0x290 netdev_master_upper_dev_link+0x1c/0x28 br_add_if+0x3f0/0x6d0 [bridge] Fix it by adding proper check for port->ndev != NULL. Fixes: 2934db9bcb30 ("net: ti: am65-cpsw-nuss: Add netdevice notifiers") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-05bnx2x: fix an error code in bnx2x_nic_load()Dan Carpenter
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current code returns success. Fixes: ad5afc89365e ("bnx2x: Separate VF and PF logic") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04net/prestera: Fix devlink groups leakage in error flowLeon Romanovsky
Devlink trap group is registered but not released in error flow, add the missing devlink_trap_groups_unregister() call. Fixes: 0a9003f45e91 ("net: marvell: prestera: devlink: add traps/groups implementation") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03nfp: update ethtool reporting of pauseframe controlFei Qin
Pauseframe control is set to symmetric mode by default on the NFP. Pause frames can not be configured through ethtool now, but ethtool can report the supported mode. Fixes: 265aeb511bd5 ("nfp: add support for .get_link_ksettings()") Signed-off-by: Fei Qin <fei.qin@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03net: sparx5: fix bitmask on 32-bit targetsArnd Bergmann
I saw the build failure that was fixed in commit 6387f65e2acb ("net: sparx5: fix compiletime_assert for GCC 4.9") and noticed another issue that was introduced in the same patch: Using GENMASK() to create a 64-bit mask does not work on 32-bit architectures. This probably won't ever happen on this driver since it's specific to a 64-bit SoC, but it's better to write it portably, so use GENMASK_ULL() instead. Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-02net: sparx5: fix compiletime_assert for GCC 4.9Jakub Kicinski
Stephen reports sparx5 broke GCC 4.9 build. Move the compiletime_assert() out of the static function. Compile-tested only, no object code changes. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-02net: natsemi: Fix missing pci_disable_device() in probe and removeWang Hai
Replace pci_enable_device() with pcim_enable_device(), pci_disable_device() and pci_release_regions() will be called in release automatically. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-04-16 17:20:22 +0000