| Age | Commit message (Collapse) | Author |
|---|
|
memset the command buffers rather than the pointers to them.
Fixes: b3f63c3d5e2c ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the lost of Ethernet port on low memory system,
when driver frees its resources and fails to allocate new resources.
Issue could happen while changing number of channels, rings size or
changing the timestamp configuration.
This fix is necessary because of removing vmap use in the code.
When vmap was in use driver could allocate non-contiguous memory
and make it contiguous with vmap. Now it could fail to allocate
a large chunk of contiguous memory and lose the port.
Current code tries to allocate new resources and then upon success
frees the old resources.
Fixes: 73898db04301 ('net/mlx4: Avoid wrong virtual mappings')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Filters cleanup should be done once before destroying net device,
since filters list is contained in the private data.
Fixes: 1eb8c695bda9 ('net/mlx4_en: Add accelerated RFS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The label lio_xmit_failed is used 3 times through liquidio_xmit() but it
always makes a call to dma_unmap_single() using potentially
uninitialized variables from "ndata" variable. Out of the 3 gotos, 2 run
after ndata has been initialized, and had a prior dma_map_single() call.
Fix this by adding a new error label: lio_xmit_dma_failed which does
this dma_unmap_single() and then processed with the lio_xmit_failed
fallthrough.
Fixes: f21fb3ed364bb ("Add support of Cavium Liquidio ethernet adapters")
Reported-by: coverity (CID 1309740)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case nb8800_receive() fails to allocate a fragment, we would leak the
SKB freshly allocated and just return, instead, free it.
Reported-by: coverity (CID 1341750)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should be using a logical check here instead of a bitwise operation
to check if the device is closed already in et131x_tx_timeout().
Reported-by: coverity (CID 146498)
Fixes: 38df6492eb511 ("et131x: Add PCIe gigabit ethernet driver et131x to drivers/net")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.
Fixes: 9cde94506eacf ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets entering the switch are mapped to a Switch Priority (SP)
according to their PCP value (untagged frames are mapped to SP 0).
The packets are classified to a priority group (PG) buffer in the port's
headroom according to their SP.
The switch maintains another mapping (SP to IEEE priority), which is
used to generate PFC frames for lossless PGs. This mapping is
initialized to IEEE = SP % 8.
Therefore, when mapping SP 'x' to PG 'y' we create a situation in which
an IEEE priority is mapped to two different PGs:
IEEE 'x' ---> SP 'x' ---> PG 'y'
IEEE 'x' ---> SP 'x + 8' ---> PG '0' (default)
Which is invalid, as a flow can use only one PG buffer.
Fix this by mapping both SP 'x' and 'x + 8' to the same PG buffer.
Fixes: 8e8dfe9fdf06 ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of supported traffic classes that can have ETS and PFC
simultaneously enabled is not subject to user configuration, so make
sure we always initialize them to the correct values following a set
operation.
Fixes: 8e8dfe9fdf06 ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Fixes: d81a6bdb87ce ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't have PAUSE frames and PFC both enabled on the same port, but
the fact that ieee_setpfc() was called doesn't necessarily mean PFC is
enabled.
Only emit errors when PAUSE frames and PFC are enabled simultaneously.
Fixes: d81a6bdb87ce ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device supports link autonegotiation, so let the user know about it
by indicating support via ethtool ops.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting a new speed we need to disable and enable the port for the
changes to take effect. We currently only do that if the operational
state of the port is up. However, setting a new speed following link
training failure will require us to explicitly set the port down and then
up.
Instead, disable and enable the port based on its administrative state.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the q_vector initialization routine sets the affinity_mask
of a q_vector based on v_idx value. Meaning a loop iterates on v_idx,
which is an incremental value, and the cpumask is created based on
this value.
This is a problem in systems with multiple logical CPUs per core (like in
SMT scenarios). If we disable some logical CPUs, by turning SMT off for
example, we will end up with a sparse cpu_online_mask, i.e., only the first
CPU in a core is online, and incremental filling in q_vector cpumask might
lead to multiple offline CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
This patch changes the way q_vector's affinity_mask is created: it iterates
on v_idx, but consumes the CPU index from the cpu_online_mask instead of
just using the v_idx incremental value.
No functional changes were introduced.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the function ixgbe_poll() returns 0 when it clean completely
the rx rings, but this foul budget accounting in core code.
Fix this returning the actual work done, capped to weight - 1, since
the core doesn't allow to return the full budget when the driver modifies
the napi status
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch sets VSI broadcast promiscuous mode during VSI add sequence
and prevents adding MAC filter if specified MAC address is broadcast.
Change-ID: Ia62251fca095bc449d0497fc44bec3a5a0136773
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are a couple of issues I found in i40e_rx_checksum while doing some
recent testing. As a result I have found the Rx checksum logic is pretty
much broken and returning that the checksum is valid for tunnels in cases
where it is not.
First the inner types are not the correct values to use to test for if a
tunnel is present or not. In addition the inner protocol types are not a
bitmask as such performing an OR of the values doesn't make sense. I have
instead changed the code so that the inner protocol types are used to
determine if we report CHECKSUM_UNNECESSARY or not. For anything that does
not end in UDP, TCP, or SCTP it doesn't make much sense to report a
checksum offload since it won't contain a checksum anyway.
This leaves us with the need to set the csum_level based on some value.
For that purpose I am using the tunnel_type field. If the tunnel type is
GRENAT or greater then this means we have a GRE or UDP tunnel with an inner
header. In the case of GRE or UDP we will have a possible checksum present
so for this reason it should be safe to set the csum_level to 1 to indicate
that we are reporting the state of the inner header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Start all tx queues (including inactive ones) when opening the netdev.
Stop all tx queues (including inactive ones) when closing the netdev.
This is a workaround for the tx timeout watchdog false alarm issue in
which the netdev watchdog is polling all the tx queues which may include
inactive queues and thus once lowering the real tx queues number
(ethtool -L) it will generate tx timeout watchdog false alarms.
Fixes: 3947ca185999 ('net/mlx5e: Implement ndo_tx_timeout callback')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change netif_tx_queue_stopped to netif_xmit_stopped. This will show
when queues are stopped due to byte queue limits.
Fixes: 3947ca185999 ('net/mlx5e: Implement ndo_tx_timeout callback')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though the hardware can be doing zero padding, we want the SKB to
be going out on the wire with the appropriate size. This fixes packet
truncations observed with e.g: ARP packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case any operation fails before we can successfully go the point
where we would register a MDIO bus, we would be going to an error label
which involves unregistering then freeing this yet to be created MDIO
bus. Update all error paths to go to label free which is the only one
valid until either the clock is enabled, or the MDIO bus is allocated
and registered. This fixes kernel oops observed while trying to
dereference the MDIO bus structure which is not yet allocated.
Fixes: a1702857724f ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During commit b54b8c2d6e3c
("net: ezchip: adapt driver to little endian architecture")
adapting to little endian architecture,
zeroing of controller was left out.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, if there is no VNIC server available during the driver
probe, the driver should wait until it receives an initialization
request from the VNIC Server to start the login process. Recent testing
has show that this is incorrectly handled in the current driver.
The proposed solution handles this initialization request by scheduling
a task in the shared workqueue that completes the login process and
registers the net device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch creates a function that handles sub-CRQ IRQ creation
separately from sub-CRQ initialization. Another function is then needed
to release sub-CRQ resources prior to sub-CRQ IRQ creation.
These additions allow the driver probe function to be simplified,
specifically during the VNIC Server login process. A timeout is also
included while waiting for completion of the login process in case
the VNIC Server is not available or some other error occurs.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQ mappings were not being properly disposed when releasing sub-CRQ's.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since ibmvnic uses multiple tx queues, start and stop all queues when
opening and closing devices.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change t4fw_version.h to update latest firmware version number
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GCC complains on unused-but-set-variable, clean this up.
Fixes: 23898c763f4a ('net/mlx5: E-Switch, Modify node guid on vf set MAC')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a788a4a040e003574b8ad17115706ab1601ec572.
This patch is wrong, the type returned doesn't fit
what the error pointer macros expect.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is likely that checking 'fman->fifo_offset' instead of
'fman->cam_offset' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt worker code for the enc28j60 relies only on the TXIF flag to
determinate if the packet transmission was completed. However the datasheet
specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
transmit abort. Also in section 12.1.4 that TXIF will be set
when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
during transmission errors.
This causes a race condition, since the worker code will invoke
enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
called, the worker from the interrupt handler will enter the path for error
handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
and releasing the packet scheduled for transmission, causing a kernel crash with
due a NULL pointer.
These crashes due a NULL pointer were observed under stress conditions of the
device. A BUG_ON() sequence was used to validate the issue was fixed, and has
been running without problems for 2 years now.
Signed-off-by: Diego Dompe <dompe@hpe.com>
Acked-by: Sergio Valverde <sergio.valverde@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(resent due to overhelpful mail client corrupting patch)
At least on Meson GXBB, the CORE_IRQ_MTL_RX_OVERFLOW interrupt is thrown
with the stmmac1000 driver, which does not support set_rx_tail_ptr. With
this patch and the clock fixes, 1G ethernet works on ODROID-C2.
Signed-off-by: Matt Corallo <git@bluematt.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 64bits kernels, device stats are 64bits wide, not 32bits.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Link UP/Down prints to kernel log when link state changes
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Valid weight assigned to ETS TClass values are 1-100
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default fallback function used by mlx5e select queue can return
any TX queues in range [0..dev->num_real_tx_queues).
The current implementation assumes that the fallback function returns
a number in the range [0.. number of channels). Actually
dev->num_real_tx_queues = (number of channels) * dev->num_tc;
which is more than the expected range if num_tc is configured and could
lead to crashes.
To fix this we test if num_tc is not configured we can safely return the
fallback suggestion, if not we will reciprocal_scale the fallback
result and normalize it to the desired range.
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ConnectX4-Lx uses an inline wqe mode that currently defaults to
requiring the entire L2 header be included in the wqe.
This patch fixes mlx5e_get_inline_hdr_size() to account for
all L2 headers (VLAN, QinQ, etc) using skb_network_offset(skb).
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a timeout to avoid an infinite loop waiting for RQ's to flush. This
occurs during AER/EEH and will also happen if the device stops posting
completions due to internal error or reset, or if moving the RQ to the
error state fails. Also cleanup posted receive resources when closing
the RQ.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add callback to handle TX timeouts.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid an infinite loop by timing out waiting for the SQ to flush. Also
clean up the TX descriptors if that happens.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get fw response.
Add delayed callback timeout work before posting the command to fw.
In case of real fw command completion we will cancel the delayed work.
In case of fw command timeout the callback timeout handler will be
called and it will simulate fw completion with timeout error.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call command completion handler in case of timeout when working in
interrupts mode.
Avoid flushing the commands workqueue after acquiring the semaphores to
prevent a potential deadlock.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device ID for VFs is in a different location than PFs. This results
in the poll always timing out for VFs. There's no good way to read the
VF device ID without using the PF's configuration space. Switch to waiting
for the health poll to start incrementing. Also remove the 1s sleep
at the beginning.
fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages. The prevents timing out waiting
for extra pages that were actually cleaned up previously.
fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In internal error state the health poll thread will eventually call
synchronize_irq() (to safely trigger command completions) which might
sleep, so we are calling sleeping function from atomic context which is
invalid.
Here we move trigger_cmd_completions(dev) to enter error state which is
the earliest stage in error state handling.
This way we won't need to wait for next health poll to trigger command
completions and will solve the scheduling while atomic issue.
mlx5_enter_error_state can be called from two contexts, protect it with
dev->intf_state_lock
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of internal error state we will simulate the commands status
through the return value translation function, but we need to simulate
all the teardown fw commands as successful so we will not have fw
command failure prints.
This also fix memory leaks that happen because we skip teardown stages
due to failed fw commands.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mvneta_mdio_probe() fails, a kernel warning is triggered due to
missing cleanup in the error path. Add the necessary cleanup.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 281 at kernel/irq/manage.c:1814 __free_percpu_irq+0xfc/0x130
percpu IRQ 38 still enabled on CPU0!
Modules linked in: bnep bluetooth xhci_plat_hcd xhci_hcd marvell_cesa armada_thermal des_generic ehci_orion mcp3021 spi_orion sfp mdio_i2c evbug fuse
CPU: 1 PID: 281 Comm: connmand Not tainted 4.7.0-rc2+ #53
Hardware name: Marvell Armada 380/385 (Device Tree)
Backtrace:
[<c0013488>] (dump_backtrace) from [<c00137d0>] (show_stack+0x18/0x1c)
r6:60010093 r5:ffffffff r4:00000000 r3:dc8ba500
[<c00137b8>] (show_stack) from [<c02c6fe0>] (dump_stack+0xa4/0xdc)
[<c02c6f3c>] (dump_stack) from [<c002d4ec>] (__warn+0xd8/0x104)
r6:c081e6a0 r5:00000000 r4:edfe5d50 r3:dc8ba500
[<c002d414>] (__warn) from [<c002d5d0>] (warn_slowpath_fmt+0x40/0x48)
r10:a0010013 r8:c09356f8 r7:00000026 r6:ef11a260 r5:edd7b980 r4:ef11a200
[<c002d594>] (warn_slowpath_fmt) from [<c008c8e0>] (__free_percpu_irq+0xfc/0x130)
r3:00000026 r2:c081e7ac
[<c008c7e4>] (__free_percpu_irq) from [<c008c95c>] (free_percpu_irq+0x48/0x74)
r10:00008914 r8:00000000 r7:ffffffed r6:c09356f8 r5:00000026 r4:ef11a200
[<c008c914>] (free_percpu_irq) from [<c043dd70>] (mvneta_open+0x118/0x134)
r6:ffffffed r5:ef01e640 r4:ef01e000 r3:ef01e000
[<c043dc58>] (mvneta_open) from [<c055f5b4>] (__dev_open+0xa4/0x108)
r7:ef01e030 r6:c06ff3d8 r5:ffff9003 r4:ef01e000
[<c055f510>] (__dev_open) from [<c055f844>] (__dev_change_flags+0x94/0x150)
r7:00001002 r6:00000001 r5:ffff9003 r4:ef01e000
[<c055f7b0>] (__dev_change_flags) from [<c055f938>] (dev_change_flags+0x20/0x50)
r8:00000000 r7:c09334c8 r6:00001002 r5:00000148 r4:ef01e000 r3:00008914
[<c055f918>] (dev_change_flags) from [<c05de044>] (devinet_ioctl+0x6f4/0x7e0)
r8:00000000 r7:c09334c8 r6:00000000 r5:ee87200c r4:00000000 r3:00008914
[<c05dd950>] (devinet_ioctl) from [<c05e0168>] (inet_ioctl+0x1b8/0x1c8)
r10:beb4499c r9:edfe4000 r8:ecf13280 r7:c096cf00 r6:beb4499c r5:eef7c240
r4:00008914
[<c05dffb0>] (inet_ioctl) from [<c053c898>] (sock_ioctl+0x78/0x300)
[<c053c820>] (sock_ioctl) from [<c0155ecc>] (do_vfs_ioctl+0x98/0xa60)
r7:00000011 r6:00008914 r5:00000011 r4:c01568d0
[<c0155e34>] (do_vfs_ioctl) from [<c01568d0>] (SyS_ioctl+0x3c/0x60)
r10:00000000 r9:edfe4000 r8:beb4499c r7:00000011 r6:00008914 r5:ecf13280
r4:ecf13280
[<c0156894>] (SyS_ioctl) from [<c000fe60>] (ret_fast_syscall+0x0/0x1c)
r8:c0010004 r7:00000036 r6:00000011 r5:000a2978 r4:00000000 r3:00009003
---[ end trace 711f625d5b04b3a7 ]---
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call wmb() to ensure writes are complete before
hardware fetches updated Tx descriptors.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
initialize ret_val
Now ixgbevf_write/read_posted_mbx use -IXGBE_ERR_MBX as the initiative
return value, but it's incorrect, cause in ixgbevf_vlan_rx_add_vid(),
it use err == IXGBE_ERR_MBX, the err returned from mac.ops.set_vfta,
and in ixgbevf_set_vfta_vf, it return from write/read_posted. so we
should initialize err with IXGBE_ERR_MBX, instead of -IXGBE_ERR_MBX.
With this fix, the other functions that called it also can work well,
cause they only care about if err is 0 or not.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
