| Age | Commit message (Collapse) | Author |
|---|
|
In case the interface is not used, power down the integrated GPHY during
suspend. Similarly to bcmgenet_open(), bcmgenet_resume() powers on the GPHY
prior to any UniMAC activity.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If bcmgenet_power_down() fails, we would want to propagate a return
value from bcmgenet_wol_power_down_cfg() to know about this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This improves performance for routing and local rx
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The start-of-frame and end-of-frame bits were accidentally swapped.
In the current code it does not make any difference, since they are
always used together.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NetCP 1.5 available on newer K2 SoCs such as K2E and K2L introduced 3
variants of the ethss subsystem, 9 port, 5 port and 2 port. These have
one host port towards the CPU and N external slave ports.
To customize the driver for these new ethss sub systems, multiple
compatibility strings are introduced. Currently some of parameters that
are different on different variants such as number of ALE ports, stats
modules and number of ports are defined through constants. These are now
changed to variables in gbe_priv data that get set based on the
compatibility string. This is required as there are no hardware
identification registers available to distinguish among the variants
of NetCP 1.5 ethss. However there is identification register available
to differentiate between NetCP 1.4 vs NetCP 1.5 and the same is made use
of in the code to differentiate them.
For more reading on the details of this peripheral, please refer to the
User Guide available at http://www.ti.com/lit/pdf/spruhz3
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following checkpatch error. It seems to have passed checkpatch
last time when original code was introduced.
ERROR: Macros with complex values should be enclosed in parentheses
#172: FILE: drivers/net/ethernet/ti/netcp_ethss.c:869:
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keystone netcp driver re-uses davinci mdio driver. So enable it
by default for keystone netcp driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethss has multiple modules within the sub system
- switch sub system
- sgmii
- mdio
- switch module
NetCP driver re-uses existing davinci mdio driver. It requires to
have its own register region to map the reg space. So restructure
the code to use separate reg region for the individual modules it
manages. Use range property to define register space of NetCP and
use reg property to define individual reg spaces. So MDIO will have
its own reg space to map. This is a pre-requisite to enable MDIO
driver for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
10G switch requires forward port number in the taginfo field,
where as it should be in packet_info field for necp 1.4 Ethss. So
fill this value correctly in the knav dma descriptor.
Also rename dma_psflags field in struct netcp_tx_pipe to switch_to_port
as it contain no flag, but the switch port number for forwarding the
packet. Add a flag to hold the new flag, SWITCH_TO_PORT_IN_TAGINFO which
will be set for 10G. This can also used in the future for other flags for
the tx_pipe.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Home routers based on ARM SoCs like BCM4708 also have bcma bus with core
supported by bgmac.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netif_carrier_off() first, since that will prevent the stack from
queuing more packets to this IF. This operation is fast, and should
behave much nicer when trying to bring down an interface under load.
Reported-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use netif_carrier_off() first, since that will prevent the stack from
queuing more packets to this IF. This operation is fast, and should
behave much nicer when trying to bring down an interface under load.
Reported-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The call to e1000e_write_protect_nvm_ich8lan() is no longer supported by HW.
Access to these registers causes a system freeze in A step hardware and is
ignored in B step hardware. This function must not be called in hardware
newer than LPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the napi_alloc_skb function to allocate an skb when running within
the softirq context to avoid calls to local_irq_save/restore.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rx coalescing value is internally converted from usecs to a value
that the hardware can use. When reporting the Rx coalescing value, this
internal value is converted back to usecs. During the conversion from
and back to usecs some rounding occurs. So, for example, when setting an
Rx usec of 30, it will be reported as 29. Fix this reporting issue by
keeping the original usec value and using that during reporting.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tx coalescing support in the driver was a software implementation
for something lacking in the hardware. Using hrtimers, the idea was to
trigger a timer interrupt after having queued a packet for transmit.
Unfortunately, as the timer value was lowered, the timer expired before
the hardware actually did the transmit and so it was racey and resulted
in unnecessary interrupts.
Remove the Tx coalescing support and hrtimer and replace with a Tx timer
that is used as a reclaim timer in case of inactivity.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware supplies a value that indicates the DMA range that it
is capable of using. Use this value rather than hard-coding it in
the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new lighter weight memory barriers when working with the device
descriptors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clarify that the queues referred to in a message when the device is
brought up are hardware queues and not necessarily related to the
Linux network queues.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the setting of the transceiver type when retrieving the device
settings using ethtool and instead set the transceiver type in the
phy_driver structure flags field. Change the transceiver type to be
internal, also.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make PCI Device ID Tables be "const" to move them out of the data segment and
remove a redundant check on CH_PCI_DEVICE_ID_TABLE_DEFINE_BEGIN in
t4_pci_id_tbl.h to guard the contents of the include file.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the phys_port_name operation. Port names are pulled from the
rocker hardware model in qemu and default to the qemu name + port id.
e.g.,
sw1p1: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:12:35:01 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
where 'sw1' comes from the qemu command line -device rocker,name=sw1, and
'p1' is port 1.
Patch is adapted from Scott's phys_port_id patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb04b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ndo_set_tx_maxrate support.
To support per tx queue maxrate limit, we use the update-qp firmware
command to do run-time rate setting for the qp that serves this tx ring.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Added resource initialization based on port-id field
- Enabled second SGMII 1G interface
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
