summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2019-12-30cxgb4/cxgb4vf: fix flow control display for auto negotiationRahul Lakkireddy
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when _only_ Rx pause is enabled, both symmetric and asymmetric pause towards local device must be enabled. Also, firmware returns the local device's flow control pause params as part of advertised capabilities and negotiated params as part of current link attributes. So, fix up ethtool's flow control pause params fetch logic to read from acaps, instead of linkattr. [1] https://standards.ieee.org/standard/802_3-2005.html Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities") Signed-off-by: Surendra Mobiya <surendra@chelsio.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-29mlxsw: spectrum: Use dedicated policer for VRRP packetsIdo Schimmel
Currently, VRRP packets and packets that hit exceptions during routing (e.g., MTU error) are policed using the same policer towards the CPU. This means, for example, that misconfiguration of the MTU on a routed interface can prevent VRRP packets from reaching the CPU, which in turn can cause the VRRP daemon to assume it is the Master router. Fix this by using a dedicated policer for VRRP packets. Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-29mlxsw: spectrum_router: Skip loopback RIFs during MAC validationAmit Cohen
When a router interface (RIF) is created the MAC address of the backing netdev is verified to have the same MSBs as existing RIFs. This is required in order to avoid changing existing RIF MAC addresses that all share the same MSBs. Loopback RIFs are special in this regard as they do not have a MAC address, given they are only used to loop packets from the overlay to the underlay. Without this change, an error is returned when trying to create a RIF after the creation of a GRE tunnel that is represented by a loopback RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which does not share the same MSBs as physical interfaces. Adding an IP address to any physical interface results in: Error: mlxsw_spectrum: All router interface MAC addresses must have the same prefix. Fix this by skipping loopback RIFs during MAC validation. Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCsMartin Blumenstingl
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate can be adjusted at runtime. So far we have been running MPLL2 with ~250MHz (and the internal m250_div with value 1), which worked enough that we could transfer data with an TX delay of 4ns. Unfortunately there is high packet loss with an RGMII PHY when transferring data (receiving data works fine though). Odroid-C1's u-boot is running with a TX delay of only 2ns as well as the internal m250_div set to 2 - no lost (TX) packets can be observed with that setting in u-boot. Manual testing has shown that the TX packet loss goes away when using the following settings in Linux (the vendor kernel uses the same settings): - MPLL2 clock set to ~500MHz - m250_div set to 2 - TX delay set to 2ns on the MAC side Update the m250_div divider settings to only accept dividers greater or equal 2 to fix the TX delay generated by the MAC. iperf3 results before the change: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender [ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver iperf3 results after the change (including an updated TX delay of 2ns): [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender [ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26bnx2x: Fix accounting of vlan resources among the PFsManish Chopra
While testing max vlan configuration on the PF, firmware gets assert as driver was configuring number of vlans more than what is supported per port/engine, it was figured out that there is an implicit vlan (hidden default vlan consuming hardware cam entry resource) which is configured default for all the clients (PF/VFs) on client_init ramrod by the adapter implicitly, so when allocating resources among the PFs this implicit vlan should be considered or total vlan entries should be reduced by one to accommodate that default/implicit vlan entry. Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26bnx2x: Use appropriate define for vlan creditManish Chopra
Although it has same value as MAX_MAC_CREDIT_E2, use MAX_VLAN_CREDIT_E2 appropriately. Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26dpaa_eth: fix DMA mapping leakMadalin Bucur
On the error path some fragments remain DMA mapped. Adding a fix that unmaps all the fragments. Rework cleanup path to be simpler. Fixes: 8151ee88bad5 ("dpaa_eth: use page backed rx buffers") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26net/mlxfw: Fix out-of-memory error in mfa2 flash burningVladyslav Tarasiuk
The burning process requires to perform internal allocations of large chunks of memory. This memory doesn't need to be contiguous and can be safely allocated by vzalloc() instead of kzalloc(). This patch changes such allocation to avoid possible out-of-memory failure. Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso, including adding a missing ipv6 match description. 2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi Bhat. 3) Fix uninit value in bond_neigh_init(), from Eric Dumazet. 4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold. 5) Fix use after free in tipc_disc_rcv(), from Tuong Lien. 6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul Chaignon. 7) Multicast MAC limit test is off by one in qede, from Manish Chopra. 8) Fix established socket lookup race when socket goes from TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening RCU grace period. From Eric Dumazet. 9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet. 10) Fix active backup transition after link failure in bonding, from Mahesh Bandewar. 11) Avoid zero sized hash table in gtp driver, from Taehee Yoo. 12) Fix wrong interface passed to ->mac_link_up(), from Russell King. 13) Fix DSA egress flooding settings in b53, from Florian Fainelli. 14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost. 15) Fix double free in dpaa2-ptp code, from Ioana Ciornei. 16) Reject invalid MTU values in stmmac, from Jose Abreu. 17) Fix refcount leak in error path of u32 classifier, from Davide Caratti. 18) Fix regression causing iwlwifi firmware crashes on boot, from Anders Kaseorg. 19) Fix inverted return value logic in llc2 code, from Chan Shu Tak. 20) Disable hardware GRO when XDP is attached to qede, frm Manish Chopra. 21) Since we encode state in the low pointer bits, dst metrics must be at least 4 byte aligned, which is not necessarily true on m68k. Add annotations to fix this, from Geert Uytterhoeven. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits) sfc: Include XDP packet headroom in buffer step size. sfc: fix channel allocation with brute force net: dst: Force 4-byte alignment of dst_metrics selftests: pmtu: fix init mtu value in description hv_netvsc: Fix unwanted rx_table reset net: phy: ensure that phy IDs are correctly typed mod_devicetable: fix PHY module format qede: Disable hardware gro when xdp prog is installed net: ena: fix issues in setting interrupt moderation params in ethtool net: ena: fix default tx interrupt moderation interval net/smc: unregister ib devices in reboot_event net: stmmac: platform: Fix MDIO init for platforms without PHY llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c) net: hisilicon: Fix a BUG trigered by wrong bytes_compl net: dsa: ksz: use common define for tag len s390/qeth: don't return -ENOTSUPP to userspace s390/qeth: fix promiscuous mode after reset s390/qeth: handle error due to unsupported transport mode cxgb4: fix refcount init for TC-MQPRIO offload tc-testing: initial tdc selftests for cls_u32 ...
2019-12-20sfc: Include XDP packet headroom in buffer step size.Charles McLachlan
Correct a mismatch between rx_page_buf_step and the actual step size used when filling buffer pages. This patch fixes the page overrun that occured when the MTU was set to anything bigger than 1692. Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20sfc: fix channel allocation with brute forceEdward Cree
It was possible for channel allocation logic to get confused between what it had and what it wanted, and end up trying to use the same channel for both PTP and regular TX. This led to a kernel panic: BUG: unable to handle page fault for address: 0000000000047635 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] SMP PTI CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.4.0-rc3-ehc14+ #900 Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013 RIP: 0010:native_queued_spin_lock_slowpath+0x188/0x1e0 Code: f3 90 48 8b 32 48 85 f6 74 f6 eb e8 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 05 48 63 f6 48 05 c0 98 02 00 48 03 04 f5 a0 c6 ed 81 <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 32 RSP: 0018:ffffc90000003d28 EFLAGS: 00010006 RAX: 0000000000047635 RBX: 0000000000000246 RCX: 0000000000040000 RDX: ffff888627a298c0 RSI: 0000000000003ffe RDI: ffff88861f6b8dd4 RBP: ffff8886225c6e00 R08: 0000000000040000 R09: 0000000000000000 R10: 0000000616f080c6 R11: 00000000000000c0 R12: ffff88861f6b8dd4 R13: ffffc90000003dc8 R14: ffff88861942bf00 R15: ffff8886150f2000 FS: 0000000000000000(0000) GS:ffff888627a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000047635 CR3: 000000000200a000 CR4: 00000000000006f0 Call Trace: <IRQ> _raw_spin_lock_irqsave+0x22/0x30 skb_queue_tail+0x1b/0x50 sock_queue_err_skb+0x9d/0xf0 __skb_complete_tx_timestamp+0x9d/0xc0 efx_dequeue_buffer+0x126/0x180 [sfc] efx_xmit_done+0x73/0x1c0 [sfc] efx_ef10_ev_process+0x56a/0xfe0 [sfc] ? tick_sched_do_timer+0x60/0x60 ? timerqueue_add+0x5d/0x70 ? enqueue_hrtimer+0x39/0x90 efx_poll+0x111/0x380 [sfc] ? rcu_accelerate_cbs+0x50/0x160 net_rx_action+0x14a/0x400 __do_softirq+0xdd/0x2d0 irq_exit+0xa0/0xb0 do_IRQ+0x53/0xe0 common_interrupt+0xf/0xf </IRQ> In the long run we intend to rewrite the channel allocation code, but for 'net' fix this by allocating extra_channels, and giving them TX queues, even if we do not in fact need them (e.g. on NICs without MAC TX timestamping), and thereby using simpler logic to assign the channels once they're allocated. Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20qede: Disable hardware gro when xdp prog is installedManish Chopra
commit 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") introduced a regression in driver that when xdp program is installed on qede device, device's aggregation feature (hardware GRO) is not getting disabled, which is unexpected with xdp. Fixes: 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: ena: fix issues in setting interrupt moderation params in ethtoolArthur Kiyanovski
Issue 1: -------- Reproduction steps: 1. sudo ethtool -C eth0 rx-usecs 128 2. sudo ethtool -C eth0 adaptive-rx on 3. sudo ethtool -C eth0 adaptive-rx off 4. ethtool -c eth0 expected output: rx-usecs 128 actual output: rx-usecs 0 Reason for issue: In stage 3, ethtool userspace calls first the ena_get_coalesce() handler to get the current value of all properties, and then the ena_set_coalesce() handler. When ena_get_coalesce() is called the adaptive interrupt moderation is still on. There is an if in the code that returns the rx_coalesce_usecs only if the adaptive interrupt moderation is off. And since it is still on, rx_coalesce_usecs is not set, meaning it stays 0. Solution to issue: Remove this if static interrupt moderation intervals have nothing to do with dynamic ones. Issue 2: -------- Reproduction steps: 1. sudo ethtool -C eth0 adaptive-rx on 2. sudo ethtool -C eth0 rx-usecs 128 3. ethtool -c eth0 expected output: rx-usecs 128 actual output: rx-usecs 0 Reason for issue: In stage 2, when ena_set_coalesce() is called, the handler tests if rx adaptive interrupt moderation is on, and if it is, it returns before getting to the part in the function that sets the rx non-adaptive interrupt moderation interval. Solution to issue: Remove the return from the function when rx adaptive interrupt moderation is on. Also cleaned up the fixed code in ena_set_coalesce by grouping together adaptive interrupt moderation toggling, and using && instead of nested ifs. Fixes: b3db86dc4b82 ("net: ena: reimplement set/get_coalesce()") Fixes: 0eda847953d8 ("net: ena: fix retrieval of nonadaptive interrupt moderation intervals") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: ena: fix default tx interrupt moderation intervalArthur Kiyanovski
Current default non-adaptive tx interrupt moderation interval is 196 us. This value is too high and might cause the tx queue to fill up. In this commit we set the default non-adaptive tx interrupt moderation interval to 64 us in order to: 1. Reduce the probability of the queue filling-up (when compared to the current default value of 196 us). 2. Reduce unnecessary tx interrupt overhead (which happens if we set the default tx interval to 0). We determined experimentally that 64 us is an optimal value that reduces interrupt rate by more than 20% without affecting performance. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: stmmac: platform: Fix MDIO init for platforms without PHYPadmanabhan Rajanbabu
The current implementation of "stmmac_dt_phy" function initializes the MDIO platform bus data, even in the absence of PHY. This fix will skip MDIO initialization if there is no PHY present. Fixes: 7437127 ("net: stmmac: Convert to phylink and remove phylib logic") Acked-by: Jayati Sahu <jayati.sahu@samsung.com> Signed-off-by: Sriram Dash <sriram.dash@samsung.com> Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: hisilicon: Fix a BUG trigered by wrong bytes_complJiangfeng Xiao
When doing stress test, we get the following trace: kernel BUG at lib/dynamic_queue_limits.c:26! Internal error: Oops - BUG: 0 [#1] SMP ARM Modules linked in: hip04_eth CPU: 0 PID: 2003 Comm: tDblStackPcap0 Tainted: G O L 4.4.197 #1 Hardware name: Hisilicon A15 task: c3637668 task.stack: de3bc000 PC is at dql_completed+0x18/0x154 LR is at hip04_tx_reclaim+0x110/0x174 [hip04_eth] pc : [<c041abfc>] lr : [<bf0003a8>] psr: 800f0313 sp : de3bdc2c ip : 00000000 fp : c020fb10 r10: 00000000 r9 : c39b4224 r8 : 00000001 r7 : 00000046 r6 : c39b4000 r5 : 0078f392 r4 : 0078f392 r3 : 00000047 r2 : 00000000 r1 : 00000046 r0 : df5d5c80 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 32c5387d Table: 1e189b80 DAC: 55555555 Process tDblStackPcap0 (pid: 2003, stack limit = 0xde3bc190) Stack: (0xde3bdc2c to 0xde3be000) [<c041abfc>] (dql_completed) from [<bf0003a8>] (hip04_tx_reclaim+0x110/0x174 [hip04_eth]) [<bf0003a8>] (hip04_tx_reclaim [hip04_eth]) from [<bf0012c0>] (hip04_rx_poll+0x20/0x388 [hip04_eth]) [<bf0012c0>] (hip04_rx_poll [hip04_eth]) from [<c04c8d9c>] (net_rx_action+0x120/0x374) [<c04c8d9c>] (net_rx_action) from [<c021eaf4>] (__do_softirq+0x218/0x318) [<c021eaf4>] (__do_softirq) from [<c021eea0>] (irq_exit+0x88/0xac) [<c021eea0>] (irq_exit) from [<c0240130>] (msa_irq_exit+0x11c/0x1d4) [<c0240130>] (msa_irq_exit) from [<c0267ba8>] (__handle_domain_irq+0x110/0x148) [<c0267ba8>] (__handle_domain_irq) from [<c0201588>] (gic_handle_irq+0xd4/0x118) [<c0201588>] (gic_handle_irq) from [<c0558360>] (__irq_svc+0x40/0x58) Exception stack(0xde3bdde0 to 0xde3bde28) dde0: 00000000 00008001 c3637668 00000000 00000000 a00f0213 dd3627a0 c0af6380 de00: c086d380 a00f0213 c0a22a50 de3bde6c 00000002 de3bde30 c0558138 c055813c de20: 600f0213 ffffffff [<c0558360>] (__irq_svc) from [<c055813c>] (_raw_spin_unlock_irqrestore+0x44/0x54) Kernel panic - not syncing: Fatal exception in interrupt Pre-modification code: int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev) { [...] [1] priv->tx_head = TX_NEXT(tx_head); [2] count++; [3] netdev_sent_queue(ndev, skb->len); [...] } An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2, tx_head has been updated, but corresponding 'skb->len' has not been added to dql_queue. And then hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim In hip04_tx_reclaim, because tx_head has been updated, bytes_compl will plus an additional "skb-> len" which has not been added to dql_queue. And then trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed). To solve the problem described above, we put "netdev_sent_queue(ndev, skb->len);" before "priv->tx_head = TX_NEXT(tx_head);" Fixes: a41ea46a9a12 ("net: hisilicon: new hip04 ethernet driver") Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20cxgb4: fix refcount init for TC-MQPRIO offloadRahul Lakkireddy
Properly initialize refcount to 1 when hardware queue arrays for TC-MQPRIO offload have been freshly allocated. Otherwise, following warning is observed. Also fix up error path to only free hardware queue arrays when refcount reaches 0. [ 130.075342] ------------[ cut here ]------------ [ 130.075343] refcount_t: addition on 0; use-after-free. [ 130.075355] WARNING: CPU: 0 PID: 10870 at lib/refcount.c:25 refcount_warn_saturate+0xe1/0x100 [ 130.075356] Modules linked in: sch_mqprio iptable_nat ib_iser libiscsi scsi_transport_iscsi ib_ipoib rdma_ucm ib_umad iw_cxgb4 libcxgb ib_uverbs x86_pkg_temp_thermal cxgb4 igb [ 130.075361] CPU: 0 PID: 10870 Comm: tc Kdump: loaded Not tainted 5.5.0-rc1+ #11 [ 130.075362] Hardware name: Supermicro X9SRE/X9SRE-3F/X9SRi/X9SRi-3F/X9SRE/X9SRE-3F/X9SRi/X9SRi-3F, BIOS 3.2 01/16/2015 [ 130.075363] RIP: 0010:refcount_warn_saturate+0xe1/0x100 [ 130.075364] Code: e8 14 41 c1 ff 0f 0b c3 80 3d 44 f4 10 01 00 0f 85 63 ff ff ff 48 c7 c7 38 9f 83 8c 31 c0 c6 05 2e f4 10 01 01 e8 ef 40 c1 ff <0f> 0b c3 48 c7 c7 10 9f 83 8c 31 c0 c6 05 17 f4 10 01 01 e8 d7 40 [ 130.075365] RSP: 0018:ffffa48d00c0b768 EFLAGS: 00010286 [ 130.075366] RAX: 0000000000000000 RBX: 0000000000000008 RCX: 0000000000000001 [ 130.075366] RDX: 0000000000000001 RSI: 0000000000000096 RDI: ffff8a2e9fa187d0 [ 130.075367] RBP: ffff8a2e93890000 R08: 0000000000000398 R09: 000000000000003c [ 130.075367] R10: 00000000000142a0 R11: 0000000000000397 R12: ffffa48d00c0b848 [ 130.075368] R13: ffff8a2e94746498 R14: ffff8a2e966f7000 R15: 0000000000000031 [ 130.075368] FS: 00007f689015f840(0000) GS:ffff8a2e9fa00000(0000) knlGS:0000000000000000 [ 130.075369] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 130.075369] CR2: 00000000006762a0 CR3: 00000007cf164005 CR4: 00000000001606f0 [ 130.075370] Call Trace: [ 130.075377] cxgb4_setup_tc_mqprio+0xbee/0xc30 [cxgb4] [ 130.075382] ? cxgb4_ethofld_restart+0x50/0x50 [cxgb4] [ 130.075384] ? pfifo_fast_init+0x7e/0xf0 [ 130.075386] mqprio_init+0x5f4/0x630 [sch_mqprio] [ 130.075389] qdisc_create+0x1bf/0x4a0 [ 130.075390] tc_modify_qdisc+0x1ff/0x770 [ 130.075392] rtnetlink_rcv_msg+0x28b/0x350 [ 130.075394] ? rtnl_calcit.isra.32+0x110/0x110 [ 130.075395] netlink_rcv_skb+0xc6/0x100 [ 130.075396] netlink_unicast+0x1db/0x330 [ 130.075397] netlink_sendmsg+0x2f5/0x460 [ 130.075399] ? _copy_from_user+0x2e/0x60 [ 130.075400] sock_sendmsg+0x59/0x70 [ 130.075401] ____sys_sendmsg+0x1f0/0x230 [ 130.075402] ? copy_msghdr_from_user+0xd7/0x140 [ 130.075403] ___sys_sendmsg+0x77/0xb0 [ 130.075404] ? ___sys_recvmsg+0x84/0xb0 [ 130.075406] ? __handle_mm_fault+0x377/0xaf0 [ 130.075407] __sys_sendmsg+0x53/0xa0 [ 130.075409] do_syscall_64+0x44/0x130 [ 130.075412] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 130.075413] RIP: 0033:0x7f688f13af10 [ 130.075414] Code: c3 48 8b 05 82 6f 2c 00 f7 db 64 89 18 48 83 cb ff eb dd 0f 1f 80 00 00 00 00 83 3d 8d d0 2c 00 00 75 10 b8 2e 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 ae cc 00 00 48 89 04 24 [ 130.075414] RSP: 002b:00007ffe6c7d9988 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [ 130.075415] RAX: ffffffffffffffda RBX: 00000000006703a0 RCX: 00007f688f13af10 [ 130.075415] RDX: 0000000000000000 RSI: 00007ffe6c7d99f0 RDI: 0000000000000003 [ 130.075416] RBP: 000000005df38312 R08: 0000000000000002 R09: 0000000000008000 [ 130.075416] R10: 00007ffe6c7d93e0 R11: 0000000000000246 R12: 0000000000000000 [ 130.075417] R13: 00007ffe6c7e9c50 R14: 0000000000000001 R15: 000000000067c600 [ 130.075418] ---[ end trace 8fbb3bf36a8671db ]--- v2: - Move the refcount_set() closer to where the hardware queue arrays are being allocated. - Fix up error path to only free hardware queue arrays when refcount reaches 0. Fixes: 2d0cb84dd973 ("cxgb4: add ETHOFLD hardware queue support") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: macb: fix probing of PHY not described in the dtAntoine Tenart
This patch fixes the case where the PHY isn't described in the device tree. This is due to the way the MDIO bus is registered in the driver: whether the PHY is described in the device tree or not, the bus is registered through of_mdiobus_register. The function masks all the PHYs and only allow probing the ones described in the device tree. Prior to the Phylink conversion this was also done but later on in the driver the MDIO bus was manually scanned to circumvent the fact that the PHY wasn't described. This patch fixes it in a proper way, by registering the MDIO bus based on if the PHY attached to a given interface is described in the device tree or not. Fixes: 7897b071ac3b ("net: macb: convert to phylink") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller
Daniel Borkmann says: ==================== pull-request: bpf 2019-12-19 The following pull-request contains BPF updates for your *net* tree. We've added 10 non-merge commits during the last 8 day(s) which contain a total of 21 files changed, 269 insertions(+), 108 deletions(-). The main changes are: 1) Fix lack of synchronization between xsk wakeup and destroying resources used by xsk wakeup, from Maxim Mikityanskiy. 2) Fix pruning with tail call patching, untrack programs in case of verifier error and fix a cgroup local storage tracking bug, from Daniel Borkmann. 3) Fix clearing skb->tstamp in bpf_redirect() when going from ingress to egress which otherwise cause issues e.g. on fq qdisc, from Lorenz Bauer. 4) Fix compile warning of unused proc_dointvec_minmax_bpf_restricted() when only cBPF is present, from Alexander Lobakin. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net/ixgbe: Fix concurrency issues between config flow and XSKMaxim Mikityanskiy
Use synchronize_rcu to wait until the XSK wakeup function finishes before destroying the resources it uses: 1. ixgbe_down already calls synchronize_rcu after setting __IXGBE_DOWN. 2. After switching the XDP program, call synchronize_rcu to let ixgbe_xsk_wakeup exit before the XDP program is freed. 3. Changing the number of channels brings the interface down. 4. Disabling UMEM sets __IXGBE_TX_DISABLED before closing hardware resources and resetting xsk_umem. Check that bit in ixgbe_xsk_wakeup to avoid using the XDP ring when it's already destroyed. synchronize_rcu is called from ixgbe_txrx_ring_disable. Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-5-maximmi@mellanox.com
2019-12-19net/i40e: Fix concurrency issues between config flow and XSKMaxim Mikityanskiy
Use synchronize_rcu to wait until the XSK wakeup function finishes before destroying the resources it uses: 1. i40e_down already calls synchronize_rcu. On i40e_down either __I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in i40e_xsk_wakeup (the former is already checked there). 2. After switching the XDP program, call synchronize_rcu to let i40e_xsk_wakeup exit before the XDP program is freed. 3. Changing the number of channels brings the interface down (see i40e_prep_for_reset and i40e_pf_quiesce_all_vsi). 4. Disabling UMEM sets __I40E_CONFIG_BUSY, too. Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com
2019-12-19net/mlx5e: Fix concurrency issues between config flow and XSKMaxim Mikityanskiy
After disabling resources necessary for XSK (the XDP program, channels, XSK queues), use synchronize_rcu to wait until the XSK wakeup function finishes, before freeing the resources. Suspend XSK wakeups during switching channels. If the XDP program is being removed, synchronize_rcu before closing the old channels to allow XSK wakeup to complete. Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-3-maximmi@mellanox.com
2019-12-18net: stmmac: Always arm TX Timer at end of transmission startJose Abreu
If TX Coalesce timer is enabled we should always arm it, otherwise we may hit the case where an interrupt is missed and the TX Queue will timeout. Arming the timer does not necessarly mean it will run the tx_clean() because this function is wrapped around NAPI launcher. Fixes: 9125cdd1be11 ("stmmac: add the initial tx coalesce schema") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: Enable 16KB buffer sizeJose Abreu
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in the calculation of RX buffer size. Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: 16KB buffer must be 16 byte alignedJose Abreu
The 16KB RX Buffer must also be 16 byte aligned. Fix it. Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: RX buffer size must be 16 byte alignedJose Abreu
We need to align the RX buffer size to at least 16 byte so that IP doesn't mis-behave. This is required by HW. Changes from v2: - Align UP and not DOWN (David) Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: xgmac: Clear previous RX buffer sizeJose Abreu
When switching between buffer sizes we need to clear the previous value. Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: Only the last buffer has the FCS fieldJose Abreu
Only the last received buffer contains the FCS field. Check for end of packet before trying to strip the FCS field. Fixes: 88ebe2cf7f3f ("net: stmmac: Rework stmmac_rx()") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: Do not accept invalid MTU valuesJose Abreu
The maximum MTU value is determined by the maximum size of TX FIFO so that a full packet can fit in the FIFO. Add a check for this in the MTU change callback. Also check if provided and rounded MTU does not passes the maximum limit of 16K. Changes from v2: - Align MTU before checking if its valid Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: Determine earlier the size of RX bufferJose Abreu
Split Header feature needs to know the size of RX buffer but current code is determining it too late. Fix this by moving the RX buffer computation to earlier stage. Changes from v2: - Do not try to align already aligned buffer size Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: selftests: Needs to check the number of Multicast regsJose Abreu
When running the MC and UC filter tests we setup a multicast address that its expected to be blocked. If the number of available multicast registers is zero, driver will always pass the multicast packets which will fail the test. Check if available multicast addresses is enough before running the tests. Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-17nfp: flower: fix stats id allocationJohn Hurley
As flower rules are added, they are given a stats ID based on the number of rules that can be supported in firmware. Only after the initial allocation of all available IDs does the driver begin to reuse those that have been released. The initial allocation of IDs was modified to account for multiple memory units on the offloaded device. However, this introduced a bug whereby the counter that controls the IDs could be decremented before the ID was assigned (where it is further decremented). This means that the stats ID could be assigned as -1/0xfffffff which is out of range. Fix this by only decrementing the main counter after the current ID has been assigned. Fixes: 467322e2627f ("nfp: flower: support multiple memory units for filter offloads") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-17net: ag71xx: fix compile warningsOleksij Rempel
drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_probe': drivers/net/ethernet/atheros/ag71xx.c:1776:30: warning: passing argument 2 of 'of_get_phy_mode' makes pointer from integer without a cast [-Wint-conversion] In file included from drivers/net/ethernet/atheros/ag71xx.c:33: ./include/linux/of_net.h:15:69: note: expected 'phy_interface_t *' {aka 'enum <anonymous> *'} but argument is of type 'int' Fixes: 0c65b2b90d13c1 ("net: of_get_phy_mode: Change API to solve int/unit warnings") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-17net: qlogic: Fix error paths in ql_alloc_large_buffers()Ben Hutchings
ql_alloc_large_buffers() has the usual RX buffer allocation loop where it allocates skbs and maps them for DMA. It also treats failure as a fatal error. There are (at least) three bugs in the error paths: 1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the first buffer that couldn't be allocated will have .skb == NULL. But the qla_buf[] array is not zero-initialised. 2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[]. This is incorrect for the last allocated skb, if DMA mapping failed. 3. Commit 1acb8f2a7a9f ("net: qlogic: Fix memory leak in ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any() after the skb is recorded in lrg_buf[], so ql_free_large_buffers() will double-free it. The bugs are somewhat inter-twined, so fix them all at once: * Clear each entry in qla_buf[] before attempting to allocate an skb for it. This goes half-way to fixing bug 1. * Set the .skb field only after the skb is DMA-mapped. This fixes the rest. Fixes: 1357bfcf7106 ("qla3xxx: Dynamically size the rx buffer queue ...") Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() ...") Fixes: 1acb8f2a7a9f ("net: qlogic: Fix memory leak in ql_alloc_large_buffers") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-17dpaa2-ptp: fix double free of the ptp_qoriq IRQIoana Ciornei
Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was used on the remove path to free any allocated resources. The ptp_qoriq IRQ is among these resources that are freed in ptp_qoriq_free() even though it is also a managed one (allocated using devm_request_threaded_irq). Drop the resource managed version of requesting the IRQ in order to not trigger a double free of the interrupt as below: [ 226.731005] Trying to free already-free IRQ 126 [ 226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707 __free_irq+0x9c/0x2b8 [ 226.743435] Modules linked in: [ 226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G W 5.4.0-03629-gfd7102c32b2c-dirty #912 [ 226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT) [ 226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO) [ 226.766022] pc : __free_irq+0x9c/0x2b8 [ 226.769758] lr : __free_irq+0x9c/0x2b8 [ 226.773493] sp : ffff8000125039f0 (...) [ 226.856275] Call trace: [ 226.858710] __free_irq+0x9c/0x2b8 [ 226.862098] free_irq+0x30/0x70 [ 226.865229] devm_irq_release+0x14/0x20 [ 226.869054] release_nodes+0x1b0/0x220 [ 226.872790] devres_release_all+0x34/0x50 [ 226.876790] device_release_driver_internal+0x100/0x1c0 Fixes: d346c9e86d86 ("dpaa2-ptp: reuse ptp_qoriq driver") Cc: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-16net: gemini: Fix memory leak in gmac_setup_txqsNavid Emamdoost
In the implementation of gmac_setup_txqs() the allocated desc_ring is leaked if TX queue base is not aligned. Release it via dma_free_coherent. Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-15cxgb4: Fix kernel panic while accessing sge_infoVishal Kulkarni
The sge_info debugfs collects offload queue info even when offload capability is disabled and leads to panic. [ 144.139871] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 144.139874] CR2: 0000000000000000 CR3: 000000082d456005 CR4: 00000000001606e0 [ 144.139876] Call Trace: [ 144.139887] sge_queue_start+0x12/0x30 [cxgb4] [ 144.139897] seq_read+0x1d4/0x3d0 [ 144.139906] full_proxy_read+0x50/0x70 [ 144.139913] vfs_read+0x89/0x140 [ 144.139916] ksys_read+0x55/0xd0 [ 144.139924] do_syscall_64+0x5b/0x1d0 [ 144.139933] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 144.139936] RIP: 0033:0x7f4b01493990 Fix this crash by skipping the offload queue access in sge_qinfo when offload capability is disabled Signed-off-by: Herat Ramani <herat@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-14bnx2x: Fix logic to get total no. of PFs per engineManish Chopra
Driver doesn't calculate total number of PFs configured on a given engine correctly which messed up resources in the PFs loaded on that engine, leading driver to exceed configuration of resources (like vlan filters etc.) beyond the limit per engine, which ended up with asserts from the firmware. Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-14bnx2x: Do not handle requests from VFs after parityManish Chopra
Parity error from the hardware will cause PF to lose the state of their VFs due to PF's internal reload and hardware reset following the parity error. Restrict any configuration request from the VFs after the parity as it could cause unexpected hardware behavior, only way for VFs to recover would be to trigger FLR on VFs and reload them. Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-14net: ethernet: ti: build cpsw-common for switchdevArnd Bergmann
Without the common part of the driver, the new file fails to link: drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_probe': cpsw_new.c:(.text+0x312c): undefined reference to `ti_cm_get_macid' Use the same Makefile hack as before, and build cpsw-common.o for any driver that needs it. Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-14net: ethernet: ti: select PAGE_POOL for switchdev driverArnd Bergmann
The new driver misses a dependency: drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_rx_handler': cpsw_new.c:(.text+0x259c): undefined reference to `__page_pool_put_page' cpsw_new.c:(.text+0x25d0): undefined reference to `page_pool_alloc_pages' drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_fill_rx_channels': cpsw_priv.c:(.text+0x22d8): undefined reference to `page_pool_alloc_pages' cpsw_priv.c:(.text+0x2420): undefined reference to `__page_pool_put_page' drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_create_xdp_rxqs': cpsw_priv.c:(.text+0x2624): undefined reference to `page_pool_create' drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_run_xdp': cpsw_priv.c:(.text+0x2dc8): undefined reference to `__page_pool_put_page' Other drivers use 'select' for PAGE_POOL, so do the same here. Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-14net: marvell: mvpp2: phylink requires the link interruptRussell King
phylink requires the MAC to report when its link status changes when operating in inband modes. Failure to report link status changes means that phylink has no idea when the link events happen, which results in either the network interface's carrier remaining up or remaining permanently down. For example, with a fiber module, if the interface is brought up and link is initially established, taking the link down at the far end will cut the optical power. The SFP module's LOS asserts, we deactivate the link, and the network interface reports no carrier. When the far end is brought back up, the SFP module's LOS deasserts, but the MAC may be slower to establish link. If this happens (which in my tests is a certainty) then phylink never hears that the MAC has established link with the far end, and the network interface is stuck reporting no carrier. This means the interface is non-functional. Avoiding the link interrupt when we have phylink is basically not an option, so remove the !port->phylink from the test. Fixes: 4bb043262878 ("net: mvpp2: phylink support") Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-13net/ibmvnic: Fix typo in retry checkThomas Falcon
This conditional is missing a bang, with the intent being to break when the retry count reaches zero. Fixes: 476d96ca9cc5 ("ibmvnic: Bound waits for device queries") Suggested-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-13bnxt: apply computed clamp value for coalece parameterJonathan Lemon
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes unresponsive, likely due to interrupt livelock. It appears that a minimum clamp value for the irq timer is computed, but is never applied. Fix by applying the corrected clamp value. Fixes: 74706afa712d ("bnxt_en: Update interrupt coalescing logic.") Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-12-12qede: Fix multicast mac configurationManish Chopra
Driver doesn't accommodate the configuration for max number of multicast mac addresses, in such particular case it leaves the device with improper/invalid multicast configuration state, causing connectivity issues (in lacp bonding like scenarios). Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10net: ena: fix napi handler misbehavior when the napi budget is zeroNetanel Belgazal
In netpoll the napi handler could be called with budget equal to zero. Current ENA napi handler doesn't take that into consideration. The napi handler handles Rx packets in a do-while loop. Currently, the budget check happens only after decrementing the budget, therefore the napi handler, in rare cases, could run over MAX_INT packets. In addition to that, this moves all budget related variables to int calculation and stop mixing u32 to avoid ambiguity Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10bnxt_en: Add missing devlink health reporters for VFs.Vasundhara Volam
The VF driver also needs to create the health reporters since VFs are also involved in firmware reset and recovery. Modify bnxt_dl_register() and bnxt_dl_unregister() so that they can be called by the VFs to register/unregister devlink. Only the PF will register the devlink parameters. With devlink registered, we can now create the health reporters on the VFs. Fixes: 6763c779c2d8 ("bnxt_en: Add new FW devlink_health_reporter") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10bnxt_en: Fix the logic that creates the health reporters.Vasundhara Volam
Fix the logic to properly check the fw capabilities and create the devlink health reporters only when needed. The current code creates the reporters unconditionally as long as bp->fw_health is valid, and that's not correct. Call bnxt_dl_fw_reporters_create() directly from the init and reset code path instead of from bnxt_dl_register(). This allows the reporters to be adjusted when capabilities change. The same applies to bnxt_dl_fw_reporters_destroy(). Fixes: 6763c779c2d8 ("bnxt_en: Add new FW devlink_health_reporter") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10bnxt_en: Remove unnecessary NULL checks for fw_healthVasundhara Volam
After fixing the allocation of bp->fw_health in the previous patch, the driver will not go through the fw reset and recovery code paths if bp->fw_health allocation fails. So we can now remove the unnecessary NULL checks. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10bnxt_en: Fix bp->fw_health allocation and free logic.Vasundhara Volam
bp->fw_health needs to be allocated for either the firmware initiated reset feature or the driver initiated error recovery feature. The current code is not allocating bp->fw_health for all the necessary cases. This patch corrects the logic to allocate bp->fw_health correctly when needed. If allocation fails, we clear the feature flags. We also add the the missing kfree(bp->fw_health) when the driver is unloaded. If we get an async reset message from the firmware, we also need to make sure that we have a valid bp->fw_health before proceeding. Fixes: 07f83d72d238 ("bnxt_en: Discover firmware error recovery capabilities.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2024-05-31 17:56:07 +0000