summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2015-10-12sfc: fully reset if MC_REBOOT event received without warm_boot_count incrementDaniel Pieczko
On EF10, MC_CMD_VPORT_RECONFIGURE can cause a CODE_MC_REBOOT event to be sent to a function without incrementing the (adapter-wide) warm_boot_count. In this case, the reboot is not detected by the loop on efx_mcdi_poll_reboot(), so prepare for recovery from an MC reboot anyway. When this codepath is run, the MC has always just rebooted, so this recovery is valid. The loop on efx_mcdi_poll_reboot() is still required for other MC reboot cases, so that actions in response to an MC reboot are performed, such as clearing locally calculated statistics. Siena NICs are unaffected by this change as the above scenario does not apply. Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-12rocker: handle setting bridge ageing_timeScott Feldman
The FDB cleanup timer will get rescheduled to re-evaluate FDB entries based on new ageing_time. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-11net: encx24j600: Fix typos in KconfigJon Ringle
Signed-off-by: Jon Ringle <jringle@gridpoint.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-11BNX2: fix a Null Pointer for stats_blkwangweidong
we have two processes to do: P1#: ifconfig eth0 down; which will call bnx2_close, then will , and set Null to stats_blk P2#: ifconfig eth0; which will call bnx2_get_stats64, it will use stats_blk. In one case: --P1#-- --P2#-- stats_blk(no null) bnx2_free_mem ->bp->stats_blk = NULL GET_64BIT_NET_STATS then it will cause 'NULL Pointer' Problem. it is as well with 'ethtool -S ethx'. Allocate the statistics block at probe time so that this problem is impossible Signed-off-by: Wang Weidong <wangweidong1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-11cxgb4: Enhance driver to update FW, when FW is too oldHariprasad Shenai
t4_check_fw_version() can return several error codes (-EINVAL, -EBUSY, -EAGAIN). The present code sets the adapter state to UNINIT only if its an EFAULT. In all the error cases set the adapter to uninitialized state. In t4_check_fw_version() if call to t4_get_fw_version() fails, repeat the operation a few times before returning failure. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09drivers/net/ethernet: make ti/cpsw-phy-sel.c explicitly non-modularPaul Gortmaker
The Kconfig currently controlling compilation of this code is: drivers/net/ethernet/ti/Kconfig:config TI_CPSW_PHY_SEL drivers/net/ethernet/ti/Kconfig: bool "TI CPSW Switch Phy sel Support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: "David S. Miller" <davem@davemloft.net> Cc: Varka Bhadram <varkabhadram@gmail.com> Cc: netdev@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx4_core: Fix resource tracker error flow in add_res_rangeSaeed Mahameed
The 'for' loop when undoing rb-tree insertions and list-adds in the error flow in add_res_range had errors, fix them. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx4_core: Fix mailbox leak in error flow when performing update qpJack Morgenstein
The procedure mlx4_update_qp leaks mailboxes in its error-flow, fix that. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx4_en: Add steering rules after RSS creationIdo Shamay
Changed the receive control flow in a way that steering rules are added only when the RSS object is already in RTR/RTS mode. Some optimization features, which are enabled by the device firmware, require this condition in order to be effective. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx5_core: Use private health thread for each deviceEli Cohen
Use a single threaded work queue for each device in the system instead of using one thread for any device. This is required so we can concurrently process system error handling for all the devices that need that. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx5_core: Use accessor functions to read from device memoryEli Cohen
Use ioread function to read health buffer data. In addition, print the firmware version as a string for readability and also use dev_err to have the device string to be printed. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx5_core: Prepare cmd interface to system errors handlingEli Cohen
In preparation to handling system errors at the mlx5_core level, change the interface of cmd_work_handler to accept a 64 bit argument for the vector. This allows to encode a flag that signifies when the handler is called as a result of a driver logic that wishes to terminate commands that the hardware may not be able to terminate. Such command completions are detected at the handler and proper return status is encoded. To be able to terminate page handler commands, we make sure to set the corresponding bit in the bitmask. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-09net/mlx5_core: Improve mlx5 messagesEli Cohen
Improve the messages printed by the mlx5 macros to include the device string. In addition, prefix names used by the macros with two underscores to avoid possible name collisions. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-08i40e: print neato new featuresJesse Brandeburg
To help users and developers know what compile options and hardware features are enabled at compile time, print VxLAN is available. Change-ID: I3162f3b7678dc725a597f964217920eb218b480b Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e/i40evf: pass QOS handle to VFMitch Williams
The VF really doesn't care about the QOS handle but it will in the future. Since the VF only uses TC0, send it that handle. On the VF side, save the handle and use it to populate the QOS params when we call into the client interface. Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40evf: use capabilities flags properlyMitch Williams
Use the capabilities passed to us by the PF driver to control VF driver behavior. In the process, clean up the VLAN add/remove code so it's not a horrible morass of ifdefs. Change-ID: I1050eaf12b658a26fea6813047c9964163c70a73 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: refactor code to remove indentJesse Brandeburg
I found a code indent that was avoidable because a whole function is inside an if block, reverse the if and move the code back a tab. Change-ID: I9989c8750ee61678fbf96a3b0fd7bf7cc7ef300a Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e/i40evf: clean up some codeJesse Brandeburg
Add missings spaces after declarations, remove another __func__ use, remove uncessary braces, remove unneeded breaks, and useless returns, and generally fix up some code. Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40evf: detect reset more reliablyMitch Williams
Using VFGEN_RSTAT to detect a VF reset is an endeavor that is fraught with peril. It's entirely too easy to miss a reset because none of the bits are sticky. By the time the VF driver reads the register, the reset may have been processed and cleaned up by the PF driver, leaving the register in the same state that it was before the reset. Instead, detect a reset with the VF_ARQLEN register. When the VF is reset, the enable bit in this register is cleared, and it stays cleared until the VF driver processes the reset and re-enables the admin queue. Because we now deal with multiple registers in the reset and watchdog tasks, rename the rstat_val variable to reg_val. Change-ID: Id1df17045c0992e607da0162d31807f7fc20d199 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: Support FW CEE DCB UP to TC map nibble swapGreg Bowers
Changes parsing of AQ command Get CEE DCBX OPER CFG (0x0A07). Change is required because FW creates the oper_prio_tc nibbles reversed from those in the CEE Priority Group sub-TLV. Change-ID: I7d9d8641bb430d30e286fc3fac909866ef8a0de8 Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e/i40evf: Explicitly assign enum index for VSI typeSerey Kong
Ran into an issue where PF's VSI type list was different from VF's, which was resulted in different enum index. The VSI type list can be different depending on what build flag is used for PF and VF. The change is to explicitly assign enum index for each VSI type so that PF and VF always reference to the same VSI type event if the enum lists are different. Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57 Signed-off-by: Serey Kong <serey.kong@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: add switch for link pollingShannon Nelson
There's been some need for controlling the periodic link polling for debugging link issues. This patch enables switching it off and on through an ethtool private flag. The link poll remains on by default, but can be turned off with ethtool --set-priv-flags p261p1 LinkPolling off and later turned back on with ethtool --set-priv-flags p261p1 LinkPolling on To check the current status, use ethtool --show-priv-flags p261p1 Change-ID: I32e4ab654ff3eec90a06cf144899971b82d71c40 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: Fix multiple link up messagesMatt Jared
This patch addresses an issue where multiple link up messages can be logged resulting from aq link status timing when link properties are changed (fc, speed, etc.); solved by using a single function to handle status printing and adding a mechanism to track whether link state (up or down) has actually changed. Change-ID: Ied6ed6e49dc397c77d992adc0bc9ed3767152b9d Signed-off-by: Matt Jared <matthew.a.jared@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: Fix for extra Flow Director filter in table after errorCarolyn Wyborny
This patch fixes a problem where the PF's fdir filter table would have an entry that the hw was unable to add. This notification happens in the hot path, so instead of trying to fix it then, we note the location in the failure case and delete it during regular fdir subtask callback. Without this patch, a case can occur where an invalid entry gets replayed and a valid one is not. Change-ID: I67831c183b5d0309876de807cc434809b74c9cb7 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e/i40evf: Store CEE DCBX DesiredCfg and RemoteCfgNeerav Parikh
This patch adds capability to query and store the CEE DCBX DesiredCfg and RemoteCfg data from the LLDP MIB. Added new member "desired_dcbx_config" in the i40e_hw data structure to hold CEE only DesiredCfg data. Change-ID: I19c550369594384eaff4cc63e690ca740231195d Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: Add parsing for CEE DCBX TLVsNeerav Parikh
This patch adds parsing for CEE DCBX TLVs from the LLDP MIB. While the driver gets the DCB CEE operational configuration from Firmware using the "Get CEE DCBX Oper Config" AQ command there is a need to get the CEE DesiredCfg Tx by firmware and DCB configuration Rx from peer; for debug and other application purposes. Change-ID: I9140edf1a25a2852c7eff805d81e5eff6266178d Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: add more verbose error messagesMitch Williams
Under certain circumstances, the device may not have enough resources to enable all of the VFs that it advertises in config space. Although the number of supported VFs is reported upon driver init, it is not obvious when this is different from the number reported in config space. To eliminate this confusion, add an error message explaining the problem. Additionally, move the 'Allocating VFs' message down below the error checks so as to prevent further confusion. Change-ID: I45b7efca53a7aebf7777be33a8bc9d615ae48ea1 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: inline interrupt enableJesse Brandeburg
The interrupt enable function can be inlined by moving it to the header file, which decreases the function call overhead for a frequently called function. Change-ID: I3214cc99593725768642680e7b8ce7e9bba7e44d Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08i40e: fix erroneous WARN_ONJesse Brandeburg
The driver was issuing a WARN_ON during ring size changes because the code was cloning the rx_ring struct but not zeroing out the pointers before allocating new memory. Zero out the pointers in the cloned copy before allocating new memory for them. In this case the code was correctly avoiding memory leaks but still triggering the warning. Change-ID: I186dd493948e9b7254ab0593d4aad8b68808918d Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-08net: hns: fix 32-bit build warningArnd Bergmann
The recently added hns driver causes a build warning in ARM allmodconfig builds: drivers/net/ethernet/hisilicon/hns/hnae.c: In function 'handles_show': drivers/net/ethernet/hisilicon/hns/hnae.c:452:13: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] j, (u64)h->qs[i]->io_base); ^ This removes the pointless cast and prints the pointer address using the "%p" format string in all three locations. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-08net: Microchip encx24j600 driverJon Ringle
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet controller over a SPI bus interface. This driver makes use of the regmap API to optimize access to registers by caching registers where possible. Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf Signed-off-by: Jon Ringle <jringle@gridpoint.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07i40e/i40evf: remove unused opcodeMitch Williams
This opcode is not required. VFs that program RSS through the firmware do it by interacting directly with the firmware, and do not need to use the virtual channel for this functionality. Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40evf: propagate interrupt allocation failureMitch Williams
Lower level functions are properly reporting errors, and higher-level functions are correctly responding to errors, but the errors aren't actually getting through. Typically, the middle-manager function seems to want to shield its boss from any bad news. This change fixes a panic if the driver is unable to enable MSI-X or is unable to acquire enough vectors. Change-ID: Ifd5787ce92519a5d97e4b465902db930d97b71a1 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: Additional checks for CEE APP priority validityNeerav Parikh
The firmware has added additional status information to allow software to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in CEE DCBX mode. This patch adds to support those additional checks and will only add applications to the software table that have oper and sync bits set without any error. Change-ID: I0a76c52427dadf97d4dba4538a3068d05e4eb56b Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e/i40evf: Add a stat to keep track of linearization countAnjali Singhai Jain
Keep track of how many times we ask the stack to linearize the skb because the HW cannot handle skbs with more than 8 frags per segment/single packet. Change-ID: If455452060963a769bbe6112cba952e79e944b52 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e/i40evf: fix unicast mac address addShannon Nelson
When using something like "ip maddr add ..." to add another unicast mac address to the netdev, the mac address comes into the set_rx_mode handler in the multicast list whether it is a unicast or multicast address. This was confusing the code when it was trying to search for addresses that needed to be deleted from the VSI, because it was looking for the VSI unicast address in the netdev unicast list. The result was that a new unicast address would get added to the VSI list and then immediately removed, and would never actually make it down into the hardware. This patch removes the separation from unicast and multicast in the search for filters to be deleted. It also simplifies the logic a little with a jump to the bottom of the loop when an address is found. Now it doesn't matter which netdev list the address is hiding in, we'll check them all. Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: fix bug in return from get_link_status and avoid spurious link messagesJesse Brandeburg
Previously, the driver could call this function and have only true/false returned, but false could mean multiple things like failure to read or link was down. This change allows the caller to get all return values in the call chain bubbled back to the source, which keeps information about failures from being lost. Also, in some unlikely scenarios, the firmware can become slow to respond to admin queue (AQ) queries for link state. Should the AQ time out, the driver can detect the state and avoid a link change when there may have been none. Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: add little endian conversion for checksumJesse Brandeburg
The checksum is not correct on big endian machines so add code to swap it correctly. Change-ID: Ic92b886d172a2cbe49f5d7eee1bc78e447023c7b Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e/i40evf: give up the __func__Shannon Nelson
During early development, we added the function name to all of the error strings to make debugging simpler. Now that we've released the driver, our users should have more comprehensible error messages. So tear the roof off and give up the __func__. Ow. Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: Never let speed get set to 0 in get_settingsCatherine Sullivan
In ethtool, there is a possibility of speed getting set to 0 if advertise is set to 0 (which it is when autoneg is disabled). We never want this to happen as the firmware will actually attempt to set the speed to 0 sending link down, so add an extra check to make sure this doesn't happen. Change-ID: I62e0eeee2cbf043d8e6f5c9c9f0b92794e877f01 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: Fix for truncated interrupt nameCarolyn Wyborny
This patch extends the size of the text available for the interrupt names. Without this patch, all the descriptive data available for the Flow Director interrupts is truncated. Change-ID: I2ac458f23ac3b4ea8f1edf73edc283b1d3704c7f Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e/i40evf: assure clean asq status reportShannon Nelson
There was a possibility where the asq_last_status could get through without update and thus report a previous error. I don't think we've actually seen this happen, but this patch will help make sure it doesn't. Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Christopher Pau <christopher.pau@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: make i40e_init_pf_fcoe to voidShannon Nelson
i40e_init_pf_fcoe() didn't return anything except 0, it prints enough error info already, and no driver logic depends on the return value, so this can be void. Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: fix bad CEE status shift valueShannon Nelson
Fix a shift value that was wrong, ending up with a bad bitmask. Also add a blank line between two sets of #defines for better readability. Change-ID: I3e41fa2a2ab904d3a4e6cbf13972ab0036a10601 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e/i40evf: fix a potential type compare issueShannon Nelson
Rework an if expression to assure there is no type compare problem between a size and a possible negative number. Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99 Reported-by: Helin Zhang <helin.zhang@intel.com> Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e/i40evf: add driver support for new device idsShannon Nelson
Early addition of new a device id. Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: stop VF ringsMitch Williams
Explicitly stop the rings belonging to each VF when disabling SR-IOV. Even though the VFs were gone, and the associated VSIs were removed, the rings were not stopped, and in some circumstances the hardware would continue to access the memory formerly used by the rings, causing memory corruption or DMAR errors, both of which would lead to general malaise of the kernel. To relieve this condition, explicitly stop all the rings associated with each VF before releasing its resources. Change-ID: I78c05d562c66e7b594b7e48d67860f49b3e5b6ec Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: enable WoL operation if config bit show WoL capableShannon Nelson
The driver was disabling Wake-on-LAN by default and waiting for the user to expressly turn it on. This patch has the driver turning on WoL from the start if enabled in the hardware config, which matches the behavior of our other drivers. Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07i40e: Increase the amount of time we wait for reset to be donePaul M Stillwell Jr
In some rare cases the reset can take longer to complete so increase the amount of time we wait. Change-ID: Ib5628ec54b526a811ee33d1214fe763226406671 Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-10-07gianfar: Add WAKE_UCAST and "wake-on-filer" supportClaudiu Manoil
This enables eTSEC's filer (Rx parser) and the FGPI Rx interrupt (Filer General Purpose Interrupt) as a wakeup source event. Upon entering suspend state, the eTSEC filer is given a rule to match incoming L2 unicast packets. A packet matching the rule will be enqueued in the Rx ring and a FGPI Rx interrupt will be asserted by the filer to wakeup the system. Other packet types will be dropped. On resume the filer table is restored to the content before entering suspend state. The set of rules from gfar_filer_config_wol() could be extended to implement other WoL capabilities as well. The "fsl,wake-on-filer" DT binding enables this capability on certain platforms that feature the necessary power management infrastructure, targeting mainly printing and imaging applications. (refer to Power Management section of the SoC Ref Man) Cc: Li Yang <leoli@freescale.com> Cc: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-05-29 18:34:59 +0000