| Age | Commit message (Collapse) | Author |
|---|
|
Introduce new functions gsi_suspend() and gsi_resume(), which will
disable the GSI interrupt handler after all endpoints are suspended
and re-enable it before endpoints are resumed. This will ensure no
GSI interrupt handler will fire when the hardware is suspended.
Here's a little further explanation. There are seven GSI interrupt
types, and most are disabled except when needed.
- These two are not used (never enabled):
GSI_INTER_EE_CH_CTRL
GSI_INTER_EE_EV_CTRL
- These two are only used to implement channel and event ring
commands, and are only enabled while a command is underway:
GSI_CH_CTRL
GSI_EV_CTRL
- The IEOB interrupt signals I/O completion. It will not fire
when a channel is stopped (or "suspended").
GSI_IEOB
- This interrupt is used to allocate or halt modem channels,
and is only enabled while such a command is underway.
GSI_GLOB_EE
However it also is used to signal certain errors, and this could
occur at any time.
- The general interrupt signals general errors, and could occur at
any time.
GSI_GENERAL
The purpose for this change is to ensure no global or general
interrupts fire due to errors while the hardware is suspended.
We enable the clock on resume, and at that time we can "handle"
(at least report) these error conditions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GSI IRQ handler could be triggered as soon as it is registered
with request_irq(). The handler function, gsi_isr(), touches
hardware, meaning the IPA clock must be operational. The IPA clock
is not operating when the handler is registered (in gsi_irq_init()),
so this is a problem.
Move the call to request_irq() for the GSI interrupt handler into
gsi_irq_setup(), which is called when the IPA clock is known to be
operational (and furthermore, the GSI firmware will have been
loaded). Request the IRQ at the end of that function, after all
interrupt types have been disabled and masked.
Move the matching free_irq() call into gsi_irq_teardown(), and get
rid of the now empty gsi_irq_exit(),
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change gsi_irq_setup() so it returns an error value, and introduce
gsi_irq_teardown() as its inverse. Set the interrupt type (IRQ
rather than MSI) in gsi_irq_setup().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move gsi_irq_setup() and gsi_ring_setup() so they're defined right
above gsi_setup() where they're called. This is a trivial movement
of code to prepare for upcoming patches.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the Boolean flags passed to __gsi_channel_start() and
__gsi_channel_stop() so they represent whether the request is being
made to implement suspend (versus stop) or resume (versus start).
Then stop or start the channel for suspend/resume requests only if
the hardware version indicates it should be done.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GSI layer has the IPA version now, so there's no need for
version-specific flags to be passed from IPA. One instance of
this is in gsi_channel_suspend() and gsi_channel_resume(), which
indicate whether or not the endpoint suspend is implemented by
GSI stopping the channel. We can make that determination based
on gsi->version, eliminating the need for a Boolean flag in those
functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are only a few remaining spots that validate IPA code
conditional on whether a symbol is defined at compile time.
The checks are not expensive, so just build them always.
This completes the removal of all CONFIG_VALIDATE/CONFIG_VALIDATION
IPA code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to IPA v3.5.1, there is no HW_PARAM_2 GSI register, which we
use to determine the number of channels and endpoints per execution
environment. In that case, we will just assume the number supported
is the maximum supported by the driver.
Introduce gsi_ring_setup() to encapsulate the code that determines
the number of channels and endpoints.
Update GSI_EVT_RING_COUNT_MAX so it is big enough to handle any
available channel for all supported hardware (IPA v4.9 can have 23
channels and 24 event rings).
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GSI inter-EE interrupts are not supported prior to IPA v3.5.
Don't attempt to initialize them in gsi_irq_setup() for hardware
that does not support them.
Originally proposed by AngeloGioacchino Del Regno.
Link: https://lore.kernel.org/netdev/20210211175015.200772-4-angelogioacchino.delregno@somainline.org
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In gsi_irq_setup(), two registers are written with the intention of
disabling inter-EE channel and event IRQs.
But the wrong registers are used (and defined); the ones used are
read-only registers that indicate whether the interrupt condition is
present.
Define the mask registers instead of the status registers, and use
them to disable the inter-EE interrupt types.
Fixes: 46f748ccaf01 ("net: ipa: explicitly disallow inter-EE interrupts")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210505223636.232527-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are place holder functions in the GSI code that do nothing.
Remove these, knowing we can add something back in their place if
they're really needed someday.
Some of these are inverse functions (such as teardown to match setup).
Explicitly comment that there is no inverse in these cases.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPA v4.5 (GSI v2.5) supports a larger set of channel protocols, and
adds an additional field to hold the most-significant bits of the
protocol identifier on a channel.
Add an inline function that encodes the protocol (including the
extra bits for newer versions of IPA), and define some additional
protocols. At this point we still use only GPI protocol.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each GSI channel has a CNTXT_1 register that encodes the size of its
ring buffer. The size of the field that records that is increased
starting at IPA v4.9. Replace the use of a fixed-size field mask
with a new inline function that encodes that size value.
Similarly, the size of GSI event rings can be larger starting with
IPA v4.9, so create a function to encode that as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify conditional tests throughout the IPA code so they do not
assume that IPA v3.5.1 is the oldest version supported. Also remove
assumptions that IPA v4.5 is the newest version of IPA supported.
Augment versions in comments with "+", to be clearer that the
comment applies to a version and subsequent versions. (E.g.,
"present for IPA v4.2+" instead of just "present for v4.2".)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible for a 32 bit x86 build to use a 64 bit DMA address.
There are two remaining spots where the IPA driver does a modulo
operation to check alignment of a DMA address, and under certain
conditions this can lead to a build error on i386 (at least).
The alignment checks we're doing are for power-of-2 values, and this
means the lower 32 bits of the DMA address can be used. This ensures
both operands to the modulo operator are 32 bits wide.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use upper_32_bits() to extract the high-order 32 bits of a DMA
address. This avoids doing a 32-position shift on a DMA address
if it happens not to be 64 bits wide. Use lower_32_bits() to
extract the low-order 32 bits (because that's what it's for).
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck report:
drivers/net/ipa/gsi.c:1341:2-9:
line 1341 is redundant because platform_get_irq() already prints an error
Remove dev_err() messages after platform_get_irq_byname() failures.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a simple helper function that indicates whether a channel has
been initialized. This abstacts/hides the details of how this is
determined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch actually fixes a bug, though it doesn't affect the two
platforms supported currently. The fix implements GSI memory
pointers a bit differently.
For IPA version 4.5 and above, the address space for almost all GSI
registers is adjusted downward by a fixed amount. This is currently
handled by adjusting the I/O virtual address pointer after it has
been mapped. The bug is that the pointer is not "de-adjusted" as it
should be when it's unmapped.
This patch fixes that error, but it does so by maintaining one "raw"
pointer for the mapped memory range. This is assigned when the
memory is mapped and used to unmap the memory. This pointer is also
used to access the two registers that do *not* sit in the "adjusted"
memory space.
Rather than adjusting *that* pointer, we maintain a separate pointer
that's an adjusted copy of the "raw" pointer, and that is used for
most GSI register accesses.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
An event ring's state only needs to be known when it is allocated,
reset, or deallocated. We check an event ring's state both before
and after performing an event ring control command that changes
its state. These are only issued at startup and shutdown, so there
is very little value in caching the state.
Stop recording a copy of the channel's last known state, and instead
fetch the true state from hardware whenever it's needed. In such
cases, *do* record the state in a local variable, in case an error
message reports it (so the value reported is the value seen).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When stopping a channel, gsi_channel_stop() will ensure NAPI
polling is complete when it calls napi_disable(). So there is no
need to call napi_synchronize() in that case.
Move the call to napi_synchronize() out of __gsi_channel_stop()
and into gsi_channel_suspend(), so it's only used where needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the mutex calls out of gsi_channel_stop_retry() and into
__gsi_channel_stop(), to make the latter more semantically similar
to __gsi_channel_start().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In gsi_channel_setup(), we check to see if the configuration data
contains any information about channels that are not supported by
the hardware. If one is found, we abort the setup process, but
the error code (ret) is not set in this case. Fix this bug.
Fixes: 650d1603825d8 ("soc: qcom: ipa: the generic software interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210204010655.15619-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Transactions to send data for a network device can be allocated at
any time up until the point the TX queue is stopped. It is possible
for ipa_start_xmit() to be called in one context just before a
the transmit queue is stopped in another.
Update gsi_channel_trans_last() so that for TX channels the
allocated and pending transaction lists are checked--in addition
to the completed and polled lists--to determine the "last"
transaction. This means any transaction that has been allocated
before the TX queue is stopped will be allowed to complete before
we conclude the channel is quiesced.
Rework the function a bit to use a list pointer and gotos.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No completion interrupts will occur while an endpoint is suspended,
nor when a channel has been stopped for suspend. So there's no need
to disable the interrupt during suspend and re-enable it when
resuming. Without any interrupts occurring, there is no need to
disable/re-enable NAPI for channel suspend/resume either.
We'll only enable NAPI and the interrupt when we first start the
channel, and disable it again only when it's "really" stopped.
To accomplish this, move the enable/disable calls out of
__gsi_channel_start() and __gsi_channel_stop(), and into
gsi_channel_start() and gsi_channel_stop() instead.
Add a call to napi_synchronize() to gsi_channel_suspend(), to ensure
NAPI polling is done before moving on.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Disable both the I/O completion interrupt and NAPI polling on a
channel *after* we successfully stop it rather than before. This
ensures a completion occurring just before the channel is stopped
gets processed.
Enable NAPI polling and the interrupt *before* starting a channel
rather than after, to be symmetric. A stopped channel won't
generate any completion interrupts anyway.
Enable NAPI before the interrupt and disable it afterward.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Open-code gsi_channel_freeze() and gsi_channel_thaw() in all callers
and get rid of these two functions. This is part of reworking the
sequence of things done during channel suspend/resume and start/stop.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a new function that does most of the work of starting a
channel. What's different is that it takes a flag indicating
whether the channel should really be started or not. Create
another new function __gsi_channel_stop() that behaves similarly.
IPA v3.5.1 implements suspend using a special SUSPEND endpoint
setting. If the endpoint is suspended when an I/O completes on the
underlying GSI channel, a SUSPEND interrupt is generated.
Newer versions of IPA do not implement the SUSPEND endpoint mode.
Instead, endpoint suspend is implemented by simply stopping the
underlying GSI channel. In this case, a completing I/O on a
*stopped* channel causes the SUSPEND interrupt condition.
These new functions put all activity related to starting or stopping
a channel (including "thawing/freezing" the channel) in one place,
whether or not the channel is actually started or stopped.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a new helper function that encapsulates issuing a set of
channel stop commands, retrying if appropriate, with a short delay
between attempts.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an error occurs starting a channel, don't "thaw" it.
We should assume the channel remains in a non-started state.
Update the comment in gsi_channel_stop(); calls to this function
are no longer retried.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The virt local variable in gsi_channel_state() does not have an
__iomem attribute but should. Fix this.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Amy Parker <enbyamy@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "ring->addr = addr;" assignment is done a few lines later so we
can't use "ring->addr" yet. The correct dma_handle is "addr".
Fixes: 650d1603825d ("soc: qcom: ipa: the generic software interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/YBjpTU2oejkNIULT@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently in gsi_isr_ieob(), event ring IEOB interrupts are disabled
one at a time. The loop disables the IEOB interrupt for all event
rings represented in the event mask. Instead, just disable them all
at once.
Disable them all *before* clearing the interrupt condition. This
guarantees we'll schedule NAPI for each event once, before another
IEOB interrupt could be signaled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename gsi_irq_ieob_disable() to be gsi_irq_ieob_disable_one().
Introduce a new function gsi_irq_ieob_disable() that takes a mask of
events to disable rather than a single event id. This will be used
in the next patch.
Rename gsi_irq_ieob_enable() to be gsi_irq_ieob_enable_one() to be
consistent.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Have gsi_channel_update() return the first transaction in the
updated completed transaction list, or NULL if no new transactions
have been added.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pay attention to the return value of napi_complete(), completing
polling only if it returns true.
Just use napi rather than &channel->napi as the argument passed to
napi_complete().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an off-by-one problem in gsi_channel_poll(). The count of
transactions completed is incremented each time through the loop
*before* determining whether there is any more work to do. As a
result, if we exit the loop early the counter its value is one more
than the number of transactions actually processed.
Instead, increment the count after processing, to ensure it reflects
the number of processed transactions. The result is more naturally
described as a for loop rather than a while loop, so change that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For RX channels we issue a stop command more than once if necessary
to allow it to stop. It turns out that TX channels could also
require retries.
Retry channel stop commands if necessary regardless of the channel
direction. Rename the symbol defining the retry count so it's not
RX-specific.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a GSI stop channel command leaves the channel in STOP_IN_PROC
state, we retry the stop command after a 1-2 millisecond delay.
I have been told that a 3-5 millisecond delay is a better choice.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The GSI command timeout is currently 5 seconds, which is much higher
than it should be.
Express the timeout in milliseconds rather than seconds, and reduce
it to 50 milliseconds.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
65;6003;1c
The use of msleep() for small periods (less than 20 milliseconds) is
not recommended because the actual delay can be much different than
expected.
We use msleep(1) in several places in the IPA driver to insert short
delays. Replace them with usleep_range calls, which should reliably
delay a period in the range requested.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a new function gsi_irq_ev_ctrl_enable() that encapsulates
enabling the event ring control GSI interrupt type, and enables a
single event ring to signal that interrupt. When an event ring
changes state as a result of an event ring command, it triggers this
interrupt.
Create an inverse function gsi_irq_ev_ctrl_disable() as well.
Because only one event ring at a time is enabled for this interrupt,
we can simply disable the interrupt for *all* channels.
Create a pair of helpers that serve the same purpose for channel
commands.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The return value of gsi_command() is true if successful or false if
we time out waiting for a completion interrupt.
Rename the variables in the three callers of gsi_command() to be
"timeout", to make it more obvious that's the only reason for
failure.
In addition, add a "gsi_" prefix to evt_ring_command() so its name
is consistent with the convention used for GSI channel and generic
commands.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Callers of evt_ring_command() no longer care whether the command
times out, and don't use what evt_ring_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 428b448ee764a ("net: ipa: use state to determine event ring command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Callers of gsi_channel_command() no longer care whether the command
times out, and don't use what gsi_channel_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6ffddf3b3d182 ("net: ipa: use state to determine channel command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch implements the same basic fix for event rings as the
previous one does for channels.
The result of issuing an event ring control command should be that
the event ring changes state. If enabled, a completion interrupt
signals that the event ring state has changed. This interrupt is
enabled by gsi_evt_ring_command() and disabled again after the
command has completed (or we time out).
There is a window of time during which the command could complete
successfully without interrupting. This would cause the event ring
to transition to the desired new state.
So whether a event ring command ends via completion interrupt or
timeout, we can consider the command successful if the event ring
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The result of issuing a channel control command should be that the
channel changes state. If enabled, a completion interrupt signals
that the channel state has changed. This interrupt is enabled by
gsi_channel_command() and disabled again after the command has
completed (or we time out).
There is a window of time--after the completion interrupt is disabled
but before the channel state is read--during which the command could
complete successfully without interrupting. This would cause the
channel to transition to the desired new state.
So whether a channel command ends via completion interrupt or
timeout, we can consider the command successful if the channel
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: d6c9e3f506ae8 ("net: ipa: only enable generic command completion IRQ when needed");
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
