| Age | Commit message (Collapse) | Author |
|---|
|
Some PHY in PHY package may require to read/write MMD regs to correctly
configure the PHY package.
Add support for these additional required function in both lock and no
lock variant.
It's assumed that the entire PHY package is either C22 or C45. We use
C22 or C45 way of writing/reading to mmd regs based on the passed phydev
whether it's C22 or C45.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restructure phy_write_mmd and phy_read_mmd to implement generic helper
for direct mdiobus access for mmd and use these helper for phydev user.
This is needed in preparation of PHY package API that requires generic
access to the mdiobus and are deatched from phydev struct but instead
access them based on PHY package base_addr and offsets.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PSGMII interface is similar to QSGMII. The main difference
is that the PSGMII interface combines five SGMII lines into a
single link while in QSGMII only four lines are combined.
Similarly to the QSGMII, this interface mode might also needs
special handling within the MAC driver.
It is commonly used by Qualcomm with their QCA807x PHY series and
modern WiSoC-s.
Add definitions for the PHY layer to allow to express this type
of connection between the MAC and PHY.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 800Gbps speed, link modes of 100Gbps per lane.
As mentioned in slide 21 in IEEE documentation [1], all adopted 802.3df
copper and optical PMDs baselines using 100G/lane will be supported.
Add the relevant PMDs which are mentioned in slide 5 in IEEE
documentation [1] and were approved on 10-2022 [2]:
BP - KR8
Cu Cable - CR8
MMF 50m - VR8
MMF 100m - SR8
SMF 500m - DR8
SMF 2km - DR8-2
[1]: https://www.ieee802.org/3/df/public/22_10/22_1004/shrikhande_3df_01a_221004.pdf
[2]: https://ieee802.org/3/df/KeyMotions_3df_221005.pdf
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 1000BASE-KX interface mode. This 1G backplane ethernet as described in
clause 70. Clause 73 autonegotiation is mandatory, and only full duplex
operation is supported.
Although at the PMA level this interface mode is identical to
1000BASE-X, it uses a different form of in-band autonegation. This
justifies a separate interface mode, since the interface mode (along
with the MLO_AN_* autonegotiation mode) sets the type of autonegotiation
which will be used on a link. This results in more than just electrical
differences between the link modes.
With regard to 1000BASE-X, 1000BASE-KX holds a similar position to
SGMII: same signaling, but different autonegotiation. PCS drivers
(which typically handle in-band autonegotiation) may only support
1000BASE-X, and not 1000BASE-KX. Similarly, the phy mode is used to
configure serdes phys with phy_set_mode_ext. Due to the different
electrical standards (SFI or XFI vs Clause 70), they will likely want to
use different configuration. Adding a phy interface mode for
1000BASE-KX helps simplify configuration in these areas.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some phy modes such as QSGMII multiplex several MAC<->PHY links on one
single physical interface. QSGMII used to be the only one supported, but
other modes such as QUSGMII also carry multiple links.
This helper allows getting the number of links that are multiplexed
on a given interface.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Block comments should not use a trailing */ on a separate line and every
line of a block comment should start with an '*'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add kerneldoc for the core PHY data structures, a few inline functions
and exported functions which are not already documented.
v2
Typos
g/phy/PHY/s
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead. Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for low latency Reed Solomon FEC as LLRS.
The LL-FEC is defined by the 25G/50G ethernet consortium,
in the document titled "Low Latency Reed Solomon Forward Error Correction"
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
|
|
The APIs can be used by Ethernet drivers without actually loading a PHY
driver. This may become more widespread in the future with 802.3z
compatible MAC PCS devices being locally driven by the MAC driver when
configuring for a PHY mode with in-band negotiation.
Check that drv is not NULL before reading from it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers to make locking/unlocking the MDIO bus easier.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there's a bug in the module subsystem [0] preventing load of
the PHY driver module on certain systems (as one symptom).
This results in a NPE on such systems for the following reason:
Instead of the correct PHY driver the genphy driver is loaded that
doesn't implement the read_page/write_page callbacks. Every call to
phy_read_paged() et al will result in a NPE therefore.
In parallel to fixing the root cause we should make sure that this one
and maybe similar issues in other subsystems don't result in a NPE
in phylib. So let's check for the callbacks before using them and warn
once if they are not available.
[0] https://marc.info/?t=157072642100001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 400Gbps speed, link modes of 50Gbps per lane
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the update of phylib's software pause mode state from
genphy_read_status(), so that we can re-use this functionality with
PHYs that have alternative ways to read the negotiation results.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
We will need the functionality of __set_linkmode_max_speed also for
linkmode bitmaps other than phydev->supported. Therefore split it.
v2:
- remove unused parameter from __set_linkmode_max_speed
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add link modes for 100Mbps and 1Gbps over a single pair.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If new PHY modes are added people may miss to update all relevant places
in the kernel. Therefore add a build bug check for new modes in enum
ethtool_link_mode_bit_indices that haven't been added to phylib yet.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently new modes have been added to ethtool.h, but the related
extension to phylib hasn't been done yet. So add support for these
modes.
v2:
- add missing 100Gbps and 50Gbps modes
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The definition of array settings[] is quite lengthy meanwhile. Add a
macro to shrink the definition.
v2:
- Fix an indentation issue
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have the settings array of modes which is sorted based on aneg
priority. Instead of checking each mode manually let's simply iterate
over the sorted settings.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since of_set_phy_supported was moved to phy-core.c, we can also move
of_set_phy_eee_broken to the same location, so that we have all OF
functions in the same place.
This patch doesn't intend to introduce any change in behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting a PHY's max speed using either the max-speed DT property
or ethtool, we should mask-out all non-compatible modes according to the
settings table, instead of just the 10/100BASET modes.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When modifying registers there are scenarios where we need to know
whether the register content actually changed. This patch adds
new helpers to not break users of the current ones, phy_modify() etc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds full set of locked and unlocked accessor functions to read and
write PHY MMD registers and/or bitfields.
Set of functions exactly matches what is already available for PHY
legacy registers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in comments and error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__phy_modify would return the old value of the register before it was
modified. Thus on success, it does not return 0, but a positive value.
Thus functions using phy_modify, which is a wrapper around
__phy_modify, can start returning > 0 on success, rather than 0. As a
result, breakage has been noticed in various places, where 0 was
assumed.
Code inspection does not find any current location where the return of
the old value is currently used. So have __phy_modify return 0 on
success. When there is a real need for the old value, either a new
accessor can be added, or an additional parameter passed.
Fixes: fea23fb591cc ("net: phy: convert read-modify-write to phy_modify()")
Fixes: 2b74e5be17d2 ("net: phy: add phy_modify() accessor")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mask argument for phy_modify() in several locations was inverted.
Fixes: fea23fb591cc ("net: phy: convert read-modify-write to phy_modify()")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add phy_modify() convenience accessor to complement the mdiobus
counterpart.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a set of paged phy register accessors which are inherently safe in
their design against other accesses interfering with the paged access.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Also added is a read-modify-write unlocked accessor with the same
locking requirements.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use unlocked accessors for indirect MMD accesses to clause 22 PHYs.
This permits tracing of these accesses.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to convert the result of the autonegotiation advertisment
into the PHYs speed and duplex settings. If the result is full duplex,
also extract the pause mode settings from the link partner advertisment.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
