| Age | Commit message (Collapse) | Author |
|---|
|
Ass the PHY interface mode into mac_disable_tx_lpi() and
mac_enable_tx_lpi() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Handle -EOPNOTSUPP from mac_enable_tx_lpi() to print a sensible error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Select the initial SFP PHY interface mode from the PHY supported
interface bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
If MDIO_USXGMII_LINK is not set, it means that the PHYs media side
link is down. Indicate back to phylink that the link as a whole is
down.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add a resume preparation function, which will ensure that the receive
clock from the PHY is appropriately configured while resuming.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add configuration of the receive clock-stop in phylink_resume() to
ensure that the clock-stop is correctly configured.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
There are hooks in the stmmac driver into XPCS to control the EEE
settings when LPI is configured at the MAC. This bypasses the layering.
To allow this to be removed from the stmmac driver, add two new
methods for PCS to inform them when the LPI/EEE enablement state
changes at the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Provide a helper to determine whether the MAC operations structure
implements the LPI operations, which will be used by both phylink and
DSA.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
We should not be configuring the PHYs clock-stop settings unless the
MAC supports phylink managed EEE. Make this dependent on MAC support.
This was noticed in a suspicious RCU usage report from the kernel
test robot (the suspicious RCU usage due to calling phy_detach()
remains unaddressed, but is triggered by the error this was
generating.)
Fixes: 03abf2a7c654 ("net: phylink: add EEE management")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1tgjNn-003q0w-Pw@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some PHYs don't support clause 45 access, and return -EOPNOTSUPP from
phy_modify_mmd(), which causes phylink_bringup_phy() to fail. Prevent
this failure by allowing -EOPNOTSUPP to also mean success.
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1tZp1a-001V62-DT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Background: https://lore.kernel.org/r/20250107123615.161095-1-ericwouds@gmail.com
Since adding negotiation of in-band capabilities, it is no longer
sufficient to just look at the MLO_AN_xxx mode and PHY interface to
decide whether to do a major configuration, since the result now
depends on the capabilities of the attaching PHY.
Always trigger a major configuration in this case.
Testing log: https://lore.kernel.org/r/f20c9744-3953-40e7-a9c9-5534b25d2e2a@gmail.com
Reported-by: Eric Woudstra <ericwouds@gmail.com>
Tested-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add EEE management to phylink, making use of the phylib implementation.
This will only be used where a MAC driver populates the methods and
capabilities bitfield, otherwise we keep our old behaviour.
Phylink will keep track of the EEE configuration, including the clock
stop abilities at each end of the MAC to PHY link, programming the PHY
appropriately and preserving the LPI configuration should the PHY go
away.
Phylink will call into the MAC driver when LPI needs to be enabled or
disabled, with the requirement that the MAC have LPI disabled prior
to the netdev being brought up (in other words, it will only call
mac_disable_tx_lpi() if it has already called mac_enable_tx_lpi().)
Support for phylink managed EEE is enabled by populating both tx_lpi
MAC operations method pointers, and filling in both LPI interfaces
and capabilities. If the methods are provided but the LPI interfaces
or capabilities remain empty, this indicates to phylink that EEE is
implemented by the driver but the hardware it is driving does not
support EEE, and thus the ethtool set_eee() and get_eee() methods will
return EOPNOTSUPP.
No validation of the LPI timer value is performed by this patch.
For interface modes which do not support LPI, we make no attempt to
manipulate the phylib EEE advertisement, but instead refuse to
activate LPI at the MAC, noting it at debug message level.
We also restrict the advertisement and reported userspace support
linkmode masks according to the lpi_capabilities provided to
phylink by the MAC driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADq-0014Pn-J1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper to determine whether the link is up or down. Currently
this is only used in one location, but becomes necessary to test
when reconfiguring EEE.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADl-0014Ph-EV@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When decoding clause 22 state, if in-band is disabled and using either
1000base-X or 2500base-X, rather than reporting link-down, we know the
speed, and we only support full duplex. Pause modes taken from XPCS.
This fixes a problem reported by Eric Woudstra.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGei-000EtL-Fn@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than using the state of the Autoneg bit, which is unreliable
with the new PCS neg mode support, use the passed neg_mode to decide
whether to decode the link partner advertisement data.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGed-000EtF-CN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current neg_mode into phylink_mii_c22_pcs_get_state() and
phylink_mii_c22_pcs_decode_state(). Update all users of phylink PCS
that use these functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeY-000Et9-8g@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As in-band AN no longer just depends on MLO_AN_INBAND + Autoneg bit,
we need to take account of the pcs_neg_mode when deciding how to
initialise the speed, duplex and pause state members before calling
into the .pcs_neg_mode() method. Add this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeO-000Esx-0r@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the PCS to specify which interfaces it supports, which
can be used by MAC drivers to build the main supported_interfaces
bitmap. Phylink also validates that the PCS returned by the MAC driver
supports the interface that the MAC was asked for.
An empty supported_interfaces bitmap from the PCS indicates that it
does not provide this information, and we handle that appropriately.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tTffL-007RoD-1Y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHY driver
It seems that phylink does not support driving PHYs in SFP modules using
the Generic PHY or Generic Clause 45 PHY driver. I've come to this
conclusion after analyzing these facts:
- sfp_sm_probe_phy(), who is our caller here, first calls
phy_device_register() and then sfp_add_phy() -> ... ->
phylink_sfp_connect_phy().
- phydev->supported is populated by phy_probe()
- phy_probe() is usually called synchronously from phy_device_register()
via phy_bus_match(), if a precise device driver is found for the PHY.
In that case, phydev->supported has a good chance of being set to a
non-zero mask.
- There is an exceptional case for the PHYs for which phy_bus_match()
didn't find a driver. Those devices sit for a while without a driver,
then phy_attach_direct() force-binds the genphy_c45_driver or
genphy_driver to them. Again, this triggers phy_probe() and renders
a good chance of phydev->supported being populated, assuming
compatibility with genphy_read_abilities() or
genphy_c45_pma_read_abilities().
- phylink_sfp_config_phy() does not support the exceptional case of
retrieving phydev->supported from the Generic PHY driver, due to its
code flow. It expects the phydev->supported mask to already be
non-empty, because it first calls phylink_validate() on it, and only
calls phylink_attach_phy() if that succeeds. Thus, phylink_attach_phy()
-> phy_attach_direct() has no chance of running.
It is not my wish to change the state of affairs by altering the code
flow, but merely to document the limitation rather than have the current
unspecific error:
[ 61.800079] mv88e6085 d0032004.mdio-mii:12 sfp: validation with support 00,00000000,00000000,00000000 failed: -EINVAL
[ 61.820743] sfp sfp: sfp_add_phy failed: -EINVAL
On the premise that an empty phydev->supported is going to make
phylink_validate() fail anyway, and that this is caused by a missing PHY
driver, it would be more informative to single out that case, undercut
the entire phylink_sfp_config_phy() call, including phylink_validate(),
and print a more specific message for this common gotcha:
[ 37.076403] mv88e6085 d0032004.mdio-mii:12 sfp: PHY i2c:sfp:16 (id 0x01410cc2) has no driver loaded
[ 37.089157] mv88e6085 d0032004.mdio-mii:12 sfp: Drivers which handle known common cases: CONFIG_BCM84881_PHY, CONFIG_MARVELL_PHY
[ 37.108047] sfp sfp: sfp_add_phy failed: -EINVAL
Link: https://lore.kernel.org/netdev/20241113144229.3ff4bgsalvj7spb7@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20241212140834.278894-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove phylink_phy_no_inband() now that we are handling the lack of
inband negotiation by querying the capabilities of the PHY and PCS,
and the BCM84881 PHY driver provides us the information necessary to
make the decision.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUsO-006IUt-KN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support for in-band signalling with Serdes links is uncertain. Some
PHYs do not support in-band for e.g. SGMII. Some PCS do not support
in-band for 2500Base-X. Some PCS require in-band for Base-X protocols.
Simply using what is in DT is insufficient when we have hot-pluggable
PHYs e.g. in the form of SFP modules, which may not provide the
in-band signalling.
In order to address this, we have introduced phy_inband_caps() and
pcs_inband_caps() functions to allow phylink to retrieve the
capabilities from each end of the PCS/PHY link. This commit adds code
to resolve whether in-band will be used in the various scenarios that
we have: In-band not being used, PHY present using SGMII or Base-X,
PHY not present. We also deal with no capabilties provided.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUsJ-006IUn-H3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a pcs_inband_caps() method to query the PCS for its inband link
capabilities, and use this to determine whether link modes used with
optical SFPs can be supported.
When a PCS does not provide a method, we allow inband negotiation to
be either on or off, making this a no-op until the pcs_inband_caps()
method is implemented by a PCS driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUs4-006IUU-7K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a more complexity in phylink_major_config(), augment
the debugging so we can see what's going on there.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrZ-006ITt-Fa@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an interdependence between the current link_an_mode and
pcs_neg_mode that some drivers rely upon to know whether inband or PHY
mode will be used.
In order to support detection of PCS and PHY inband capabilities
resulting in automatic selection of inband or PHY mode, we need to
cater for this, and support changing the MAC link_an_mode. However, we
end up with an inter-dependency between the current link_an_mode and
pcs_neg_mode.
To solve this, split the current link_an_mode into the requested
link_an_mode and active link_an_mode. The requested link_an_mode will
always be passed to phylink_pcs_neg_mode(), and the active link_an_mode
will be used for everything else, and only updated during
phylink_major_config(). This will ensure that phylink_pcs_neg_mode()'s
link_an_mode will not depend on the active link_an_mode that will,
in a future patch, depend on pcs_neg_mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrU-006ITn-Ai@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the call to phylink_pcs_neg_mode() in phylink_major_config() after
we have selected the appropriate PCS to allow the PCS to be passed in.
Add struct phylink and struct phylink_pcs pointers to
phylink_pcs_neg_mode() and pass in the appropriate structures. Set
pl->pcs_neg_mode before returning, and remove the return value.
This will allow the capabilities of the PCS and any PHY to be used when
deciding which pcs_neg_mode should be used.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrP-006ITh-6u@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc8).
Conflicts:
tools/testing/selftests/net/.gitignore
252e01e68241 ("selftests: net: add netlink-dumps to .gitignore")
be43a6b23829 ("selftests: ncdevmem: Move ncdevmem under drivers/net/hw")
https://lore.kernel.org/all/20241113122359.1b95180a@canb.auug.org.au/
drivers/net/phy/phylink.c
671154f174e0 ("net: phylink: ensure PHY momentary link-fails are handled")
7530ea26c810 ("net: phylink: remove "using_mac_select_pcs"")
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c
5b366eae7193 ("stmmac: dwmac-intel-plat: fix call balance of tx_clk handling routines")
e96321fad3ad ("net: ethernet: Switch back to struct platform_driver::remove()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Normally, phylib won't notify changes in quick succession. However, as
a result of commit 3e43b903da04 ("net: phy: Immediately call
adjust_link if only tx_lpi_enabled changes") this is no longer true -
it is now possible that phy_link_down() and phy_link_up() will both
complete before phylink's resolver has run, which means it'll miss that
pl->phy_state.link momentarily became false.
Rename "mac_link_dropped" to be more generic "link_failed" since it will
cover more than the MAC/PCS end of the link failing, and arrange to set
this in phylink_phy_change() if we notice that the PHY reports that the
link is down.
This will ensure that we capture an EEE reconfiguration event.
Fixes: 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/E1tAtcW-002RBS-LB@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have reduced the indentation level, clean up the code
formatting.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQz-002Ff5-EA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch() statement doesn't sit very well with the preceeding if()
statements, so let's just convert everything to if()s. As a result of
the two preceding commits, there is now only one case in the switch()
statement. Remove the switch statement and reduce the code indentation.
Code reformatting will be in the following commit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQu-002Fez-AA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch() statement doesn't sit very well with the preceeding if()
statements, and results in excessive indentation that spoils code
readability. Continue cleaning this up by converting the MLO_AN_PHY
case to use an if() statmeent.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQp-002Fet-5W@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch() statement doesn't sit very well with the preceeding if()
statements, and results in excessive indentation that spoils code
readability. Begin cleaning this up by converting the MLO_AN_FIXED case
to an if() statement.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQk-002Fen-1A@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the handling of manual flow control configuration to a common
location during resolve. We currently evaluate this for all but
fixed links.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQe-002Feh-T1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are a few issues with how SFP PHYs are attached:
a) The phylink_sfp_connect_phy() and phylink_sfp_config_phy() code
validates the configuration three times:
1. To discover the support/advertising masks that the PHY/PCS/MAC
can support in order to select an interface.
2. To validate the selected interface.
3. When the PHY is brought up after being attached, another validation
is done.
This is needlessly complex.
b) The configuration is set prior to the PHY being attached, which
means we don't have the PHY available in phylink_major_config()
for phylink_pcs_neg_mode() to make decisions upon.
We have already added an extra step to validate the selected interface,
so we can now move the attachment and bringup of the PHY earlier,
inside phylink_sfp_config_phy(). This results in the validation at
step 2 above becoming entirely unnecessary, so remove that too.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcb-000c8H-3e@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate that the returned interface from sfp_select_interface() is
supportable by the MAC/PCS. If it isn't, print an error and return
the NA interface type. This is a preparatory step to reorganising
how a PHY on a SFP module is handled.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcV-000c8B-Vz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever we call sfp_select_interface(), we check the returned value
and print an error. There are two cases where this happens with the
same message. Provide a common function to do this.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcQ-000c85-S4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink_parse_fixedlink() wants to preserve the pause, asym_pause and
autoneg bits in pl->supported. Rather than reading the bits into
separate bools, zeroing pl->supported, and then setting them if they
were previously set, use a mask and linkmode_and() to achieve the same
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1t3Fh5-000aQi-Nk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With DSA's implementation of the mac_select_pcs() method removed, we
can now remove the detection of mac_select_pcs() implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
When the mac_select_pcs() method is not implemented, there is no way
for pl->pcs to be set to a non-NULL value. This was here to support
the old phylink_set_pcs() method which has been removed a few years
ago. Simplify the code in phylink_validate_mac_and_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
phylink has historically not permitted a PCS to be removed. An attempt
to permit this with phylink_set_pcs() resulted in comments indicating
that there was no need for this. This behaviour has been propagated
forward to the mac_select_pcs() approach as it was believed from these
comments that changing this would be NAK'd.
However, with mac_select_pcs(), it takes more code and thus complexity
to maintain this behaviour, which can - and in this case has - resulted
in a bug. If mac_select_pcs() returns NULL for a particular interface
type, but there is already a PCS in-use, then we skip the pcs_validate()
method, but continue using the old PCS. Also, it wouldn't be expected
behaviour by implementers of mac_select_pcs().
Allow this by removing this old unnecessary restriction.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
PHYs performing rate-matching using MAC-side flow-control always
perform duplex-matching as well in case they are supporting
half-duplex modes at all.
No longer remove half-duplex modes from their capabilities.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/b157c0c289cfba024039a96e635d037f9d946745.1728617993.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink
The function allows for the configuration of a fixed link state for a given
phylink instance. This addition is particularly useful for network devices that
operate with a fixed link configuration, where the link parameters do not change
dynamically. By using `phylink_set_fixed_link()`, drivers can easily set up
the fixed link state during initialization or configuration changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net_dev->ethtool is a pointer to new struct ethtool_netdev_state, which
currently contains only the wol_enabled field.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/293a562278371de7534ed1eb17531838ca090633.1719502239.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
10G-QXGMII is a MAC-to-PHY interface defined by the USXGMII multiport
specification. It uses the same signaling as USXGMII, but it multiplexes
4 ports over the link, resulting in a maximum speed of 2.5G per port.
Some in-tree SoCs like the NXP LS1028A use "usxgmii" when they mean
either the single-port USXGMII or the quad-port 10G-QXGMII variant, and
they could get away just fine with that thus far. But there is a need to
distinguish between the 2 as far as SerDes drivers are concerned.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since ovr_an_inband no longer overrides every MLO_AN_xxx mode, rename
it to reflect what it now does - it changes the default mode from
MLO_AN_PHY to MLO_AN_INBAND. Fix up the two users of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMv-00Ecr1-Sk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Of the two users of phylink_config->ovr_an_inband, both manually check
for a fixed link before setting this flag (or clearing it if they find
a fixed link.) This is unnecessary complication.
Test ovr_an_inband before checking for the fixed-link properties, which
will allow ovr_an_inband to be overriden by a fixed link specification.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMq-00Ecqv-P8@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Of the two users of phylink_config->ovr_an_inband, both manually check
for a fixed link before setting this flag (or clearing it if they find
a fixed link.) This is unnecessary complication.
Rearrange phylink_parse_mode() a little so we can change how
phylink_config->ovr_an_inband works. This will allow the flag to be
tested before checking for the fixed link properties in the next patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMl-00Ecqp-K0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The series is causing issues with PHY drivers built as modules.
Since it was only partially applied and the merge window has
opened let's revert and try again for v6.11.
Revert 6916e461e793 ("net: phy: Introduce ethernet link topology representation")
Revert 0ec5ed6c130e ("net: sfp: pass the phy_device when disconnecting an sfp module's PHY")
Revert e75e4e074c44 ("net: phy: add helpers to handle sfp phy connect/disconnect")
Revert fdd353965b52 ("net: sfp: Add helper to return the SFP bus name")
Revert 841942bc6212 ("net: ethtool: Allow passing a phy index for some commands")
Link: https://lore.kernel.org/all/171242462917.4000.9759453824684907063.git-patchwork-notify@kernel.org/
Link: https://lore.kernel.org/all/20240507102822.2023826-1-maxime.chevallier@bootlin.com/
Link: https://lore.kernel.org/r/20240513154156.104281-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a debugging print in phylink_validate_phy() when we detect that the
PHY has not supplied a possible_interfaces bitmap.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/E1s15rq-00AHye-22@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
