| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Use the phy interface mode bitmaps for SFP modules and PHYs to select
the operating interface for SFPs and PHYs with SFPs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Select the host interface configuration according to the capabilities
of the host; this allows the kernel to support SFP modules using the
88x3310.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Pass the supported PHY interface types to phylib so that PHY drivers
can select an appropriate host configuration mode for their interface
according to the host capabilities.
This is only done for SFP modules presently.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Where a MAC provides the PHY interface mode capabilities, use the PHY
interface mode bitmaps to select the operating interface mode for
optical SFP modules, rather than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add parsing the SFP EEPROM to supported phy interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Display SFP module information verbosely, splitting the generic parts
into a separate file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a compatible for SFP+ cages. SFP+ cages are backwards compatible,
but the ethernet device behind them may not support the slower speeds
of SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add debugfs support to SFP so that the internal state of the SFP state
machines and hardware signal state can be viewed from userspace, rather
than having to compile a debug kernel to view state state transitions
in the kernel log. The 'state' output looks like:
Module state: empty
Module probe attempts: 0 0
Device state: up
Main state: down
Fault recovery remaining retries: 5
PHY probe remaining retries: 12
moddef0: 0
rx_los: 1
tx_fault: 1
tx_disable: 1
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Cooled SFP+ transceivers need a longer initialisation (startup) time.
Select the initialisation time depending on the cooled option bit.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phy_error() is called from phy_interrupt() or phy_state_machine(), and
uses WARN_ON() to print a backtrace. The backtrace is not useful when
reporting a PHY error.
However, a system may contain multiple ethernet PHYs, and phy_error()
gives no clue which one caused the problem.
Replace WARN_ON() with a call to phydev_err() so that we can see which
PHY had an error, and also inform the user that we are halting the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow the PHY to probe when there is no firmware, but do not allow the
link to come up by forcing the PHY state to PHY_HALTED in a similar way
to phy_error().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Provide phy driver start/stop hooks so that the PHY driver knows when
the network driver is starting or stopping. This will be used for the
Marvell 10G driver so that we can sanely refuse to start if the PHYs
firmware is not present, and also so that we can sanely support SFPs
behind the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Support reporting the hardware resolved pause enablement states via
phylib, overriding our software implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow phylib drivers to pass the hardware-resolved pause state to MAC
drivers, rather than using the software-based pause resolution code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for configuring the LEDs. Macchiatobin has an oddity in
that the left LED goes out when the cable is connected, and flashes
when there's link activity. This is because the reset default for
the LED outputs assume that the LED is connected to supply, not to
ground. Add support for configuring the LED modes and polarities.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for the downshift tunable for the Marvell 88x3310 PHY.
Downshift is only usable with firmware 0.3.5.0 and later.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that have a "one" in the
mask, phydev->drv->phy_id_mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
If we intend to use PCS operations, mac_pcs_get_state() will not be
implemented, so will be NULL. If we also intend to register the PCS
operations in mac_prepare() or mac_config(), then this leads to an
attempt to call NULL function pointer during phylink_start(). Avoid
this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
The configuration register definitions from table 13 official PHY datasheet:
PHYAD[2:0] = PHY Address
AN[1:0] = Auto-Negotiation
Mode = Interface Mode Select
RX Delay = RX Delay
TX Delay = TX Delay
SELRGV = RGMII/GMII Selection
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER.
Fixes this build error:
ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe':
drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size'
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: netdev@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When phy_is_started() was added to catch incorrect PHY states,
phy_stop() would not be qualified against PHY_DOWN. It is possible to
reach that state when the PHY driver has been unbound and the network
device is then brought down.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the micrel phy driver calls phy_init_hw() as a workaround,
the commit 9886a4dbd2aa ("net: phy: call phy_disable_interrupts()
in phy_init_hw()") disables the interrupt unexpectedly. So,
call phy_disable_interrupts() in phy_attach_direct() instead.
Otherwise, the phy cannot link up after the ethernet cable was
disconnected.
Note that other drivers (like at803x.c) also calls phy_init_hw().
So, perhaps, the driver caused a similar issue too.
Fixes: 9886a4dbd2aa ("net: phy: call phy_disable_interrupts() in phy_init_hw()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
|
|
Fix the registers being written to as the values were being over written
when writing the same registers.
Fixes: caabee5b53f5 ("net: phy: dp83867: support Wake on LAN")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RGMII control register at 0x32 indicates the states for the bits
RGMII_TX_CLK_DELAY and RGMII_RX_CLK_DELAY as follows:
RGMII Transmit/Receive Clock Delay
0x0 = RGMII transmit clock is shifted with respect to transmit/receive data.
0x1 = RGMII transmit clock is aligned with respect to transmit/receive data.
This commit fixes the inversed behavior of these bits
Fixes: 736b25afe284 ("net: dp83869: Add RGMII internal delay configuration")
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
There are a couple of spelling mistakes in comment text. Fix these.
Signed-off-by: Kaige Li <likaige@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c3e302edca24 ("net: phy: marvell10g: fix temperature sensor on 2110")
added a check for PHY ID via phydev->drv->phy_id in a function which is
called by devres at a time when phydev->drv is already set to null by
phy_remove function.
This null pointer dereference can be triggered via SFP subsystem with a
SFP module containing this Marvell PHY. When the SFP interface is put
down, the SFP subsystem removes the PHY.
Fixes: c3e302edca24 ("net: phy: marvell10g: fix temperature sensor on 2110")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit introduced a late error path in phy_device_create()
which fails to release the device name allocated by dev_set_name().
Fixes: 13d0ab6750b2 ("net: phy: check return code when requesting PHY driver module")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYLIB is not selected by the mvusb driver but it uses mdio devres
helpers. Explicitly select MDIO_DEVRES in this driver's Kconfig entry.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1814cff26739 ("net: phy: add a Kconfig option for mdio_devres")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO device reset assert and deassert length was created by
usleep_range() but that does not ensure optimal handling of
all the different values from device tree properties.
By switching to the new flexible sleeping helper function,
fsleep(), the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Load new "reset-post-delay-us" value from MDIO properties,
and if configured to a greater then zero delay do a
flexible sleeping delay after MDIO bus reset deassert.
This allows devices to exit reset state before start
bus communication.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO bus reset pulse width is created by using udelay()
and that function might not be optimal depending on
device tree value. By switching to the new fsleep() helper
the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the patch below, the iteration through the available MMDs is
completely short-circuited, and devs_in_pkg remains set to the initial
value of zero.
Due to devs_in_pkg being zero, the rest of get_phy_c45_ids() is
short-circuited too: the following loop never reaches below this point
either (it executes "continue" for every device in package, failing to
retrieve PHY ID for any of them):
/* Now probe Device Identifiers for each device present. */
for (i = 1; i < num_ids; i++) {
if (!(devs_in_pkg & (1 << i)))
continue;
So c45_ids->device_ids remains populated with zeroes. This causes an
Aquantia AQR412 PHY (same as any C45 PHY would, in fact) to be probed by
the Generic PHY driver.
The issue seems to be a case of submitting partially committed work (and
therefore testing something other than was submitted).
The intention of the patch was to delay exiting the loop until one more
condition is reached (the devs_in_pkg read from hardware is either 0, OR
mostly f's). So fix the patch to reflect that.
Tested with traffic on a LS1028A-QDS, the PHY is now probed correctly
using the Aquantia driver. The devs_in_pkg bit field is set to
0xe000009a, and the MMDs that are present have the following IDs:
[ 5.600772] libphy: get_phy_c45_ids: device_ids[1]=0x3a1b662
[ 5.618781] libphy: get_phy_c45_ids: device_ids[3]=0x3a1b662
[ 5.630797] libphy: get_phy_c45_ids: device_ids[4]=0x3a1b662
[ 5.654535] libphy: get_phy_c45_ids: device_ids[7]=0x3a1b662
[ 5.791723] libphy: get_phy_c45_ids: device_ids[29]=0x3a1b662
[ 5.804050] libphy: get_phy_c45_ids: device_ids[30]=0x3a1b662
[ 5.816375] libphy: get_phy_c45_ids: device_ids[31]=0x0
[ 7.690237] mscc_felix 0000:00:00.5: PHY [0.5:00] driver [Aquantia AQR412] (irq=POLL)
[ 7.704739] mscc_felix 0000:00:00.5: PHY [0.5:01] driver [Aquantia AQR412] (irq=POLL)
[ 7.718918] mscc_felix 0000:00:00.5: PHY [0.5:02] driver [Aquantia AQR412] (irq=POLL)
[ 7.733044] mscc_felix 0000:00:00.5: PHY [0.5:03] driver [Aquantia AQR412] (irq=POLL)
Fixes: bba238ed037c ("net: phy: continue searching for C45 MMDs even if first returned ffff:ffff")
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an interface to configure the advertisement for a clause 22 PCS
PHY, and set the AN enable flag in the BMCR appropriately.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a way for MAC PCS to have private data while keeping independence
from struct phylink_config, which is used for the MAC itself. We need
this independence as we will have stand-alone code for PCS that is
independent of the MAC. Introduce struct phylink_pcs, which is
designed to be embedded in a driver private data structure.
This structure does not include a mdio_device as there are PCS
implementations such as the Marvell DSA and network drivers where this
is not necessary.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With PCS support, how we implement interface reconfiguration (or other
major reconfiguration) is not up to the job; we end up reconfiguring
the PCS for an interface change while the link could potentially be up.
In order to solve this, add two additional MAC methods for major
configuration, one to prepare for the change, and one to finish the
change.
This allows mvneta and mvpp2 to shutdown what they require prior to the
MAC and PCS configuration calls, and then restart as appropriate.
This impacts ksettings_set(), which now needs to identify whether the
change is a minor tweak to the advertisement masks or whether the
interface mode has changed, and call the appropriate function for that
update.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-code the pause in-band advertisement update in light of the addition
of PCS support, so that we perform the minimum required; only the PCS
configuration function needs to be called in this case, followed by the
request to trigger a restart of negotiation if the programmed
advertisement changed.
We need to change the pcs_config() signature to pass whether resolved
pause should be passed to the MAC for setups such as mvneta and mvpp2
where doing so overrides the MAC manual flow controls.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For fixed links, we only allow the current settings, so this should be
a matter of merely rejecting an attempt to change the settings. If the
settings agree, then there is nothing more we need to do.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than recomputing whether AN is enabled, use config.an_enabled.
Suggested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we have a PHY attached, an ethtool ksettings_set() call only
really needs to call through to the phylib equivalent; phylib will
call back to us when the link changes so we can update our state.
Therefore, we can bypass most of our ksettings_set() call for this
case.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the ksettings_set() implementation to look more like phylib's
implementation; use a switch() for validating the autoneg setting, and
use the linkmode_modify() helper to set the autoneg bit in the
advertisement mask.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
