| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch is to set register to allow the mbox enter sleep status
if it does not have tx traffic and wakeup it if tx traffic arrive.
After mbox enter sleep status, the soc will enter sleep status by
firmware, this will save power. The power consume drops from about
90mW to about 10mW with this patch.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-3-git-send-email-kvalo@codeaurora.org
|
|
sdio bus bandwidth is low, sometimes for high performance TX test,
it will lack of ath10k_sdio_bus_request, it will print message:
ath10k_sdio mmc1:0001:1: unable to allocate bus request for async request
change the num from 64 to 1024 will not happen it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-3-wgong@codeaurora.org
|
|
It seems to be unused.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.
The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This define is only used for RX bundling so it is more descriptive if
RX is added to the define-name.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
irq_wq in struct ath10k_sdio is a remnant from an earlier
version of the sdio patchset.
Its use was removed as a result of Kalle's review, but somehow
the struct member survived.
It is not used and can therefore safely be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Chipsets like QCA6584 have support for SDIO so add initial SDIO bus support to
ath10k. With this patch we have the low level HTC protocol working and it's
possible to boot the firmware, but it's still not possible to connect or
anything like. More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k SDIO support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: refactoring, cleanup, commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
