summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/broadcom/brcm80211/brcmsmac
AgeCommit message (Collapse)Author
2024-12-13wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()Dmitry Antipov
In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN() instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access. Compile tested only. Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241210070441.836362-1-dmantipov@yandex.ru
2024-10-31wifi: brcm80211: Remove unused dma_txflush()Dr. David Alan Gilbert
dma_fxflush() has been unused since 2013's commit 7b2385b95363 ("brcmsmac: rework of mac80211 .flush() callback operation") Remove it. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241025204651.244627-1-linux@treblig.org
2024-10-17wifi: brcmsmac: Remove unused brcms_debugfs_get_devdir()Dr. David Alan Gilbert
brcms_debugfs_get_devdir() has been unused since it was added by commit 8e21df23894e ("brcmsmac: hardware info in debugfs") Remove it. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241004004259.470853-1-linux@treblig.org
2024-09-03wifi: brcmsmac: Use kvmemdup to simplify the codeJinjie Ruan
Use kvmemdup instead of kvmalloc() + memcpy() to simplify the code. No functional change. Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240821070257.2298559-1-ruanjinjie@huawei.com
2024-08-04wifi: brcmsmac: clean up unnecessary current_ampdu_cnt and related checksDmitry Kandybka
In 'brcms_c_ffpld_check_txfunfl()', 'current_ampdu_cnt' is hardcoded to zero, so 'txunfl_ratio' is always zero as well and some dead code can be removed. Compile tested only. Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by: Dmitry Kandybka <d.kandybka@gmail.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240801101531.6626-1-d.kandybka@gmail.com
2024-06-26wifi: brcmsmac: advertise MFP_CAPABLE to enable WPA3Arend van Spriel
After being asked about support for WPA3 for BCM43224 chipset it was found that all it takes is setting the MFP_CAPABLE flag and mac80211 will take care of all that is needed [1]. Link: https://lore.kernel.org/linux-wireless/20200526155909.5807-2-Larry.Finger@lwfinger.net/ [1] Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Tested-by: Reijer Boekhoff <reijerboekhoff@protonmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240617122609.349582-1-arend.vanspriel@broadcom.com
2024-06-26wifi: mac80211: inform the low level if drv_stop() is a suspendEmmanuel Grumbach
This will allow the low level driver to take different actions for different flows. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240618192529.739036208b6e.Ie18a2fe8e02bf2717549d39420b350cfdaf3d317@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-06-10Merge tag 'wireless-next-2024-06-07' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.11 The first "new features" pull request for v6.11 with changes both in stack and in drivers. Nothing out of ordinary, except that we have two conflicts this time: net/mac80211/cfg.c https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au drivers/net/wireless/microchip/wilc1000/netdev.c https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au Major changes: cfg80211/mac80211 * parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers wilc1000 * read MAC address during probe to make it visible to user space iwlwifi * bump FW API to 91 for BZ/SC devices * report 64-bit radiotap timestamp * enable P2P low latency by default * handle Transmit Power Envelope (TPE) advertised by AP * start using guard() rtlwifi * RTL8192DU support ath12k * remove unsupported tx monitor handling * channel 2 in 6 GHz band support * Spatial Multiplexing Power Save (SMPS) in 6 GHz band support * multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support * dynamic VLAN support * add panic handler for resetting the firmware state ath10k * add qcom,no-msa-ready-indicator Device Tree property * LED support for various chipsets * tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits) wifi: ath12k: add hw_link_id in ath12k_pdev wifi: ath12k: add panic handler wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity() wifi: brcm80211: remove unused structs wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type) wifi: ath12k: do not process consecutive RDDM event dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup() wifi: rtlwifi: handle return value of usb init TX/RX wifi: rtlwifi: Enable the new rtl8192du driver wifi: rtlwifi: Add rtl8192du/sw.c wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg wifi: rtlwifi: Add rtl8192du/dm.{c,h} wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h} wifi: rtlwifi: Add rtl8192du/rf.{c,h} wifi: rtlwifi: Add rtl8192du/trx.{c,h} wifi: rtlwifi: Add rtl8192du/phy.{c,h} wifi: rtlwifi: Add rtl8192du/hw.{c,h} wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU wifi: rtlwifi: Add rtl8192du/table.{c,h} ... Signed-off-by: Jakub Kicinski <kuba@kernel.org> ==================== Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-01wifi: brcm80211: remove unused structsDr. David Alan Gilbert
'brcmf_pcie_core_info' was added in commit 9e37f045d5e7 ("brcmfmac: Adding PCIe bus layer support.") but never used. 'brcms_c_bit_desc' last use was removed in commit cdf4352f5c59 ("brcmsmac: Improve tx trace and debug support"). Remove them. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240526234553.286773-1-linux@treblig.org
2024-06-01wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)Erick Archer
It is preferred to use sizeof(*pointer) instead of sizeof(type) due to the type of the variable can change and one needs not change the former (unlike the latter). This patch has no effect on runtime behavior. At the same time remove some redundant NULL initializations. Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Erick Archer <erick.archer@outlook.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/AS8PR02MB7237FF1C2E880D1231684D708BF02@AS8PR02MB7237.eurprd02.prod.outlook.com
2024-05-22tracing/treewide: Remove second parameter of __assign_str()Steven Rostedt (Google)
With the rework of how the __string() handles dynamic strings where it saves off the source string in field in the helper structure[1], the assignment of that value to the trace event field is stored in the helper value and does not need to be passed in again. This means that with: __string(field, mystring) Which use to be assigned with __assign_str(field, mystring), no longer needs the second parameter and it is unused. With this, __assign_str() will now only get a single parameter. There's over 700 users of __assign_str() and because coccinelle does not handle the TRACE_EVENT() macro I ended up using the following sed script: git grep -l __assign_str | while read a ; do sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file; mv /tmp/test-file $a; done I then searched for __assign_str() that did not end with ';' as those were multi line assignments that the sed script above would fail to catch. Note, the same updates will need to be done for: __assign_str_len() __assign_rel_str() __assign_rel_str_len() I tested this with both an allmodconfig and an allyesconfig (build only for both). [1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/ Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts. Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs Tested-by: Guenter Roeck <linux@roeck-us.net>
2024-05-18Merge tag 'kbuild-v6.10' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild updates from Masahiro Yamada: - Avoid 'constexpr', which is a keyword in C23 - Allow 'dtbs_check' and 'dt_compatible_check' run independently of 'dt_binding_check' - Fix weak references to avoid GOT entries in position-independent code generation - Convert the last use of 'optional' property in arch/sh/Kconfig - Remove support for the 'optional' property in Kconfig - Remove support for Clang's ThinLTO caching, which does not work with the .incbin directive - Change the semantics of $(src) so it always points to the source directory, which fixes Makefile inconsistencies between upstream and downstream - Fix 'make tar-pkg' for RISC-V to produce a consistent package - Provide reasonable default coverage for objtool, sanitizers, and profilers - Remove redundant OBJECT_FILES_NON_STANDARD, KASAN_SANITIZE, etc. - Remove the last use of tristate choice in drivers/rapidio/Kconfig - Various cleanups and fixes in Kconfig * tag 'kbuild-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (46 commits) kconfig: use sym_get_choice_menu() in sym_check_prop() rapidio: remove choice for enumeration kconfig: lxdialog: remove initialization with A_NORMAL kconfig: m/nconf: merge two item_add_str() calls kconfig: m/nconf: remove dead code to display value of bool choice kconfig: m/nconf: remove dead code to display children of choice members kconfig: gconf: show checkbox for choice correctly kbuild: use GCOV_PROFILE and KCSAN_SANITIZE in scripts/Makefile.modfinal Makefile: remove redundant tool coverage variables kbuild: provide reasonable defaults for tool coverage modules: Drop the .export_symbol section from the final modules kconfig: use menu_list_for_each_sym() in sym_check_choice_deps() kconfig: use sym_get_choice_menu() in conf_write_defconfig() kconfig: add sym_get_choice_menu() helper kconfig: turn defaults and additional prompt for choice members into error kconfig: turn missing prompt for choice members into error kconfig: turn conf_choice() into void function kconfig: use linked list in sym_set_changed() kconfig: gconf: use MENU_CHANGED instead of SYMBOL_CHANGED kconfig: gconf: remove debug code ...
2024-05-14wifi: brcmsmac: LCN PHY code is used for BCM4313 2G-only deviceSamasth Norway Ananda
The band_idx variable in the function wlc_lcnphy_tx_iqlo_cal() will never be set to 1 as BCM4313 is the only device for which the LCN PHY code is used. This is a 2G-only device. Fixes: 5b435de0d786 ("net: wireless: add brcm80211 drivers") Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240509231037.2014109-1-samasth.norway.ananda@oracle.com
2024-05-10kbuild: use $(src) instead of $(srctree)/$(src) for source directoryMasahiro Yamada
Kbuild conventionally uses $(obj)/ for generated files, and $(src)/ for checked-in source files. It is merely a convention without any functional difference. In fact, $(obj) and $(src) are exactly the same, as defined in scripts/Makefile.build: src := $(obj) When the kernel is built in a separate output directory, $(src) does not accurately reflect the source directory location. While Kbuild resolves this discrepancy by specifying VPATH=$(srctree) to search for source files, it does not cover all cases. For example, when adding a header search path for local headers, -I$(srctree)/$(src) is typically passed to the compiler. This introduces inconsistency between upstream and downstream Makefiles because $(src) is used instead of $(srctree)/$(src) for the latter. To address this inconsistency, this commit changes the semantics of $(src) so that it always points to the directory in the source tree. Going forward, the variables used in Makefiles will have the following meanings: $(obj) - directory in the object tree $(src) - directory in the source tree (changed by this commit) $(objtree) - the top of the kernel object tree $(srctree) - the top of the kernel source tree Consequently, $(srctree)/$(src) in upstream Makefiles need to be replaced with $(src). Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
2024-04-26wifi: brcmsmac: ampdu: remove unused cb_del_ampdu_pars structChristophe JAILLET
struct cb_del_ampdu_pars was added in the initial commit 5b435de0d7868 ("net: wireless: add brcm80211 drivers") and its only usage was removed in commit e041f65d5f00 ("brcmsmac: Remove internal tx queue"). Remove the structure definition now. This saves a few lines of code. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/fa3b190b6e9cba65ecc36fc93121c6ed8704f704.1714036681.git.christophe.jaillet@wanadoo.fr
2024-02-28wifi: brcmsmac: silence sparse warningsJohannes Berg
sparse complains on this code about casts that lose bits due to the usage of bitwise not, but really we do want 16 bits only, so clarify that by using masks. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240223114023.06e5ade90bcd.I41a0cbae1fa259cfbf5fa117ddfce908877475a2@changeid
2024-02-16wifi: brcmsmac: avoid function pointer castsArnd Bergmann
An old cleanup went a little too far and causes a warning with clang-16 and higher as it breaks control flow integrity (KCFI) rules: drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c:64:34: error: cast from 'void (*)(struct brcms_phy *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict] 64 | brcms_init_timer(physhim->wl, (void (*)(void *))fn, | ^~~~~~~~~~~~~~~~~~~~ Change this one instance back to passing a void pointer so it can be used with the timer callback interface. Fixes: d89a4c80601d ("staging: brcm80211: removed void * from softmac phy") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240213100548.457854-1-arnd@kernel.org
2024-02-08wifi: mac80211: simplify non-chanctx driversJohannes Berg
There are still surprisingly many non-chanctx drivers, but in mac80211 that code is a bit awkward. Simplify this by having those drivers assign 'emulated' ops, so that the mac80211 code can be more unified between non-chanctx/chanctx drivers. This cuts the number of places caring about it by about 15, which are scattered across - now they're fewer and no longer in the channel context handling. Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-02-05wifi: brcmsmac: Drop legacy headerLinus Walleij
The driver is using all the modern abstractions to obtain and use GPIOs and the legacy <linux/gpio.h> header is unused, so drop it. Fixes: a8e59744e16b ("gpiolib: split linux/gpio/driver.h out of linux/gpio.h") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240131-descriptors-wireless-v1-3-e1c7c5d68746@linaro.org
2024-01-18wifi: brcmsmac: phy: Remove unreachable codeArtem Chernyshev
wlc_phy_txpwr_srom_read_nphy() in wlc_phy_attach_nphy() can not return false, so it's impossible to get true value in this if-statement. Also change those functions return types to void since no one using it. Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru> Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20230814093621.289754-1-artem.chernyshev@red-soft.ru
2023-10-30wifi: brcmsmac: replace deprecated strncpy with memcpyJustin Stitt
Let's move away from using strncpy and instead use the more obvious interface for this context. For wlc->pub->srom_ccode, we're just copying two bytes from ccode into wlc->pub->srom_ccode with no expectation that srom_ccode be NUL-terminated: wlc->pub->srom_ccode is only used in regulatory_hint(): 1193 | if (wl->pub->srom_ccode[0] && 1194 | regulatory_hint(wl->wiphy, wl->pub->srom_ccode)) 1195 | wiphy_err(wl->wiphy, "%s: regulatory hint failed\n", __func__); We can see that only index 0 and index 1 are accessed. 3307 | int regulatory_hint(struct wiphy *wiphy, const char *alpha2) 3308 | { ... | ... 3322 | request->alpha2[0] = alpha2[0]; 3323 | request->alpha2[1] = alpha2[1]; ... | ... 3332 | } Since this is just a simple byte copy with correct lengths, let's use memcpy(). There should be no functional change. In a similar boat, both wlc->country_default and wlc->autocountry_default are just simple byte copies so let's use memcpy. However, FWICT they aren't used anywhere. (they should be used or removed -- not in scope of my patch, though). Signed-off-by: Justin Stitt <justinstitt@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231017-strncpy-drivers-net-wireless-broadcom-brcm80211-brcmfmac-cfg80211-c-v3-2-af780d74ae38@google.com
2023-10-30wifi: brcm80211: replace deprecated strncpy with strscpyJustin Stitt
Let's move away from using strncpy and instead favor a less ambiguous and more robust interface. For ifp->ndev->name, we expect ifp->ndev->name to be NUL-terminated based on its use in format strings within core.c: 67 | char *brcmf_ifname(struct brcmf_if *ifp) 68 | { 69 | if (!ifp) 70 | return "<if_null>"; 71 | 72 | if (ifp->ndev) 73 | return ifp->ndev->name; 74 | 75 | return "<if_none>"; 76 | } ... 288 | static netdev_tx_t brcmf_netdev_start_xmit(struct sk_buff *skb, 289 | struct net_device *ndev) { ... 330 | brcmf_dbg(INFO, "%s: insufficient headroom (%d)\n", 331 | brcmf_ifname(ifp), head_delta); ... 336 | bphy_err(drvr, "%s: failed to expand headroom\n", 337 | brcmf_ifname(ifp)); For di->name, we expect di->name to be NUL-terminated based on its usage with format strings: | brcms_dbg_dma(di->core, | "%s: DMA64 tx doesn't have AE set\n", | di->name); Looking at its allocation we can see that it is already zero-allocated which means NUL-padding is not required: | di = kzalloc(sizeof(struct dma_info), GFP_ATOMIC); For wlc->modulecb[i].name, we expect each name in wlc->modulecb to be NUL-terminated based on their usage with strcmp(): | if (!strcmp(wlc->modulecb[i].name, name) && NUL-padding is not required as wlc is zero-allocated in: brcms_c_attach_malloc() -> | wlc = kzalloc(sizeof(struct brcms_c_info), GFP_ATOMIC); For all these cases, a suitable replacement is `strscpy` due to the fact that it guarantees NUL-termination on the destination buffer without unnecessarily NUL-padding. Signed-off-by: Justin Stitt <justinstitt@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231017-strncpy-drivers-net-wireless-broadcom-brcm80211-brcmfmac-cfg80211-c-v3-1-af780d74ae38@google.com
2023-08-02wifi: brcmsmac: cleanup SCB-related data typesDmitry Antipov
Drop unused and set-but-unused fields of 'struct scb_ampdu_tid_ini', 'struct scb_ampdu' and 'struct scb', as well as now unused argument of 'brcms_c_ampdu_tx_operational()', adjust related code. Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230725162400.192357-2-dmantipov@yandex.ru
2023-08-02wifi: brcmsmac: remove more unused data typesDmitry Antipov
Remove unused 'struct brcmu_iovar' and 'struct tx_inst_power'. This follows commit b2090d93d4b6 ("wifi: brcmsmac: remove unused data type"). Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230725162400.192357-1-dmantipov@yandex.ru
2023-07-25wifi: brcmsmac: remove unused data typeDmitry Antipov
Remove unused 'struct gpioh_item'. It seems it was so since commit 5b435de0d786 ("net: wireless: add brcm80211 drivers"). Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230719083232.158177-1-dmantipov@yandex.ru
2023-06-16wifi: brcmsmac: fix gnu_printf warningsKalle Valo
With GCC 13.1 and W=1 brcmsmac has warnings like this: ./include/trace/stages/stage5_get_offsets.h:23:31: warning: function 'trace_event_get_offsets_brcms_dbg' might be a candidate for 'gnu_printf' format attribute [-Wsuggest-attribute=format] Add a workaround which disables -Wsuggest-attribute=format in brcms_trace_brcmsmac_msg.h. I see similar workarounds in other drivers as well. Compile tested only. Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230613140918.389690-3-kvalo@kernel.org
2023-04-26Merge tag 'net-next-6.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Paolo Abeni: "Core: - Introduce a config option to tweak MAX_SKB_FRAGS. Increasing the default value allows for better BIG TCP performances - Reduce compound page head access for zero-copy data transfers - RPS/RFS improvements, avoiding unneeded NET_RX_SOFTIRQ when possible - Threaded NAPI improvements, adding defer skb free support and unneeded softirq avoidance - Address dst_entry reference count scalability issues, via false sharing avoidance and optimize refcount tracking - Add lockless accesses annotation to sk_err[_soft] - Optimize again the skb struct layout - Extends the skb drop reasons to make it usable by multiple subsystems - Better const qualifier awareness for socket casts BPF: - Add skb and XDP typed dynptrs which allow BPF programs for more ergonomic and less brittle iteration through data and variable-sized accesses - Add a new BPF netfilter program type and minimal support to hook BPF programs to netfilter hooks such as prerouting or forward - Add more precise memory usage reporting for all BPF map types - Adds support for using {FOU,GUE} encap with an ipip device operating in collect_md mode and add a set of BPF kfuncs for controlling encap params - Allow BPF programs to detect at load time whether a particular kfunc exists or not, and also add support for this in light skeleton - Bigger batch of BPF verifier improvements to prepare for upcoming BPF open-coded iterators allowing for less restrictive looping capabilities - Rework RCU enforcement in the verifier, add kptr_rcu and enforce BPF programs to NULL-check before passing such pointers into kfunc - Add support for kptrs in percpu hashmaps, percpu LRU hashmaps and in local storage maps - Enable RCU semantics for task BPF kptrs and allow referenced kptr tasks to be stored in BPF maps - Add support for refcounted local kptrs to the verifier for allowing shared ownership, useful for adding a node to both the BPF list and rbtree - Add BPF verifier support for ST instructions in convert_ctx_access() which will help new -mcpu=v4 clang flag to start emitting them - Add ARM32 USDT support to libbpf - Improve bpftool's visual program dump which produces the control flow graph in a DOT format by adding C source inline annotations Protocols: - IPv4: Allow adding to IPv4 address a 'protocol' tag. Such value indicates the provenance of the IP address - IPv6: optimize route lookup, dropping unneeded R/W lock acquisition - Add the handshake upcall mechanism, allowing the user-space to implement generic TLS handshake on kernel's behalf - Bridge: support per-{Port, VLAN} neighbor suppression, increasing resilience to nodes failures - SCTP: add support for Fair Capacity and Weighted Fair Queueing schedulers - MPTCP: delay first subflow allocation up to its first usage. This will allow for later better LSM interaction - xfrm: Remove inner/outer modes from input/output path. These are not needed anymore - WiFi: - reduced neighbor report (RNR) handling for AP mode - HW timestamping support - support for randomized auth/deauth TA for PASN privacy - per-link debugfs for multi-link - TC offload support for mac80211 drivers - mac80211 mesh fast-xmit and fast-rx support - enable Wi-Fi 7 (EHT) mesh support Netfilter: - Add nf_tables 'brouting' support, to force a packet to be routed instead of being bridged - Update bridge netfilter and ovs conntrack helpers to handle IPv6 Jumbo packets properly, i.e. fetch the packet length from hop-by-hop extension header. This is needed for BIT TCP support - The iptables 32bit compat interface isn't compiled in by default anymore - Move ip(6)tables builtin icmp matches to the udptcp one. This has the advantage that icmp/icmpv6 match doesn't load the iptables/ip6tables modules anymore when iptables-nft is used - Extended netlink error report for netdevice in flowtables and netdev/chains. Allow for incrementally add/delete devices to netdev basechain. Allow to create netdev chain without device Driver API: - Remove redundant Device Control Error Reporting Enable, as PCI core has already error reporting enabled at enumeration time - Move Multicast DB netlink handlers to core, allowing devices other then bridge to use them - Allow the page_pool to directly recycle the pages from safely localized NAPI - Implement lockless TX queue stop/wake combo macros, allowing for further code de-duplication and sanitization - Add YNL support for user headers and struct attrs - Add partial YNL specification for devlink - Add partial YNL specification for ethtool - Add tc-mqprio and tc-taprio support for preemptible traffic classes - Add tx push buf len param to ethtool, specifies the maximum number of bytes of a transmitted packet a driver can push directly to the underlying device - Add basic LED support for switch/phy - Add NAPI documentation, stop relaying on external links - Convert dsa_master_ioctl() to netdev notifier. This is a preparatory work to make the hardware timestamping layer selectable by user space - Add transceiver support and improve the error messages for CAN-FD controllers New hardware / drivers: - Ethernet: - AMD/Pensando core device support - MediaTek MT7981 SoC - MediaTek MT7988 SoC - Broadcom BCM53134 embedded switch - Texas Instruments CPSW9G ethernet switch - Qualcomm EMAC3 DWMAC ethernet - StarFive JH7110 SoC - NXP CBTX ethernet PHY - WiFi: - Apple M1 Pro/Max devices - RealTek rtl8710bu/rtl8188gu - RealTek rtl8822bs, rtl8822cs and rtl8821cs SDIO chipset - Bluetooth: - Realtek RTL8821CS, RTL8851B, RTL8852BS - Mediatek MT7663, MT7922 - NXP w8997 - Actions Semi ATS2851 - QTI WCN6855 - Marvell 88W8997 - Can: - STMicroelectronics bxcan stm32f429 Drivers: - Ethernet NICs: - Intel (1G, icg): - add tracking and reporting of QBV config errors - add support for configuring max SDU for each Tx queue - Intel (100G, ice): - refactor mailbox overflow detection to support Scalable IOV - GNSS interface optimization - Intel (i40e): - support XDP multi-buffer - nVidia/Mellanox: - add the support for linux bridge multicast offload - enable TC offload for egress and engress MACVLAN over bond - add support for VxLAN GBP encap/decap flows offload - extend packet offload to fully support libreswan - support tunnel mode in mlx5 IPsec packet offload - extend XDP multi-buffer support - support MACsec VLAN offload - add support for dynamic msix vectors allocation - drop RX page_cache and fully use page_pool - implement thermal zone to report NIC temperature - Netronome/Corigine: - add support for multi-zone conntrack offload - Solarflare/Xilinx: - support offloading TC VLAN push/pop actions to the MAE - support TC decap rules - support unicast PTP - Other NICs: - Broadcom (bnxt): enforce software based freq adjustments only on shared PHC NIC - RealTek (r8169): refactor to addess ASPM issues during NAPI poll - Micrel (lan8841): add support for PTP_PF_PEROUT - Cadence (macb): enable PTP unicast - Engleder (tsnep): add XDP socket zero-copy support - virtio-net: implement exact header length guest feature - veth: add page_pool support for page recycling - vxlan: add MDB data path support - gve: add XDP support for GQI-QPL format - geneve: accept every ethertype - macvlan: allow some packets to bypass broadcast queue - mana: add support for jumbo frame - Ethernet high-speed switches: - Microchip (sparx5): Add support for TC flower templates - Ethernet embedded switches: - Broadcom (b54): - configure 6318 and 63268 RGMII ports - Marvell (mv88e6xxx): - faster C45 bus scan - Microchip: - lan966x: - add support for IS1 VCAP - better TX/RX from/to CPU performances - ksz9477: add ETS Qdisc support - ksz8: enhance static MAC table operations and error handling - sama7g5: add PTP capability - NXP (ocelot): - add support for external ports - add support for preemptible traffic classes - Texas Instruments: - add CPSWxG SGMII support for J7200 and J721E - Intel WiFi (iwlwifi): - preparation for Wi-Fi 7 EHT and multi-link support - EHT (Wi-Fi 7) sniffer support - hardware timestamping support for some devices/firwmares - TX beacon protection on newer hardware - Qualcomm 802.11ax WiFi (ath11k): - MU-MIMO parameters support - ack signal support for management packets - RealTek WiFi (rtw88): - SDIO bus support - better support for some SDIO devices (e.g. MAC address from efuse) - RealTek WiFi (rtw89): - HW scan support for 8852b - better support for 6 GHz scanning - support for various newer firmware APIs - framework firmware backwards compatibility - MediaTek WiFi (mt76): - P2P support - mesh A-MSDU support - EHT (Wi-Fi 7) support - coredump support" * tag 'net-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2078 commits) net: phy: hide the PHYLIB_LEDS knob net: phy: marvell-88x2222: remove unnecessary (void*) conversions tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp. net: amd: Fix link leak when verifying config failed net: phy: marvell: Fix inconsistent indenting in led_blink_set lan966x: Don't use xdp_frame when action is XDP_TX tsnep: Add XDP socket zero-copy TX support tsnep: Add XDP socket zero-copy RX support tsnep: Move skb receive action to separate function tsnep: Add functions for queue enable/disable tsnep: Rework TX/RX queue initialization tsnep: Replace modulo operation with mask net: phy: dp83867: Add led_brightness_set support net: phy: Fix reading LED reg property drivers: nfc: nfcsim: remove return value check of `dev_dir` net: phy: dp83867: Remove unnecessary (void*) conversions net: ethtool: coalesce: try to make user settings stick twice net: mana: Check if netdev/napi_alloc_frag returns single page net: mana: Rename mana_refill_rxoob and remove some empty lines net: veth: add page_pool stats ...
2023-03-31wifi: brcmsmac: ampdu: remove unused suc_mpdu variableTom Rix
clang with W=1 reports drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:848:5: error: variable 'suc_mpdu' set but not used [-Werror,-Wunused-but-set-variable] u8 suc_mpdu = 0, tot_mpdu = 0; ^ This variable is not used so remove it. Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230327151151.1771350-1-trix@redhat.com
2023-03-31wifi: brcmsmac: remove unused has_5g variableTom Rix
clang with W=1 reports drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1051:6: error: variable 'has_5g' set but not used [-Werror,-Wunused-but-set-variable] int has_5g = 0; ^ This variable is not used so remove it. Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230325130343.1334209-1-trix@redhat.com
2023-03-06gpiolib: split linux/gpio/driver.h out of linux/gpio.hArnd Bergmann
Almost all gpio drivers include linux/gpio/driver.h, and other files should not rely on includes from this header. Remove the indirect include from here and include the correct headers directly from where they are used. Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Lee Jones <lee@kernel.org>
2022-11-04bcma: Use the proper gpio includeLinus Walleij
The <linux/bcma/bcma_driver_chipcommon.h> is including the legacy header <linux/gpio.h> to obtain struct gpio_chip. Instead, include <linux/gpio/driver.h> where this struct is defined. It turns out that the brcm80211 brcmsmac depends on this to bring in the symbol gpio_is_valid(). The driver looks up the BCMA parent GPIO driver and checks that this succeeds, but then it goes on to use the deprecated GPIO call gpio_is_valid() to check the consistency of the .base member of the BCMA GPIO struct. The whole check can be dropped because the bcma_gpio is initialized in the declarations: struct gpio_chip *bcma_gpio = &cc_drv->gpio; And this can never be NULL. Cc: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221028092332.238728-1-linus.walleij@linaro.org
2022-10-10wifi: mac80211: add wake_tx_queue callback to driversAlexander Wetzel
mac80211 is fully switching over to the internal TX queue (iTXQ) implementation. Update all drivers not yet providing the now mandatory wake_tx_queue() callback. As an side effect the netdev interfaces of all updated drivers will switch to the noqueue qdisc. Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de> [add staging drivers] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-08-26Merge tag 'wireless-next-2022-08-26-v2' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Johannes berg says: ==================== Various updates: * rtw88: operation, locking, warning, and code style fixes * rtw89: small updates * cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work * brcmfmac: a couple of fixes * misc cleanups etc. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2022-08-09wifi: brcmsmac: remove duplicate wordsRuffalo Lavoisier
Remove repeated 'to' from 'to to' Signed-off-by: Ruffalo Lavoisier <RuffaloLavoisier@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220731225850.106290-1-RuffaloLavoisier@gmail.com
2022-08-05Merge tag 'trace-v6.0' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing updates from Steven Rostedt: - Runtime verification infrastructure This is the biggest change here. It introduces the runtime verification that is necessary for running Linux on safety critical systems. It allows for deterministic automata models to be inserted into the kernel that will attach to tracepoints, where the information on these tracepoints will move the model from state to state. If a state is encountered that does not belong to the model, it will then activate a given reactor, that could just inform the user or even panic the kernel (for which safety critical systems will detect and can recover from). - Two monitor models are also added: Wakeup In Preemptive (WIP - not to be confused with "work in progress"), and Wakeup While Not Running (WWNR). - Added __vstring() helper to the TRACE_EVENT() macro to replace several vsnprintf() usages that were all doing it wrong. - eprobes now can have their event autogenerated when the event name is left off. - The rest is various cleanups and fixes. * tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits) rv: Unlock on error path in rv_unregister_reactor() tracing: Use alignof__(struct {type b;}) instead of offsetof() tracing/eprobe: Show syntax error logs in error_log file scripts/tracing: Fix typo 'the the' in comment tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT tracing: Use free_trace_buffer() in allocate_trace_buffers() tracing: Use a struct alignof to determine trace event field alignment rv/reactor: Add the panic reactor rv/reactor: Add the printk reactor rv/monitor: Add the wwnr monitor rv/monitor: Add the wip monitor rv/monitor: Add the wip monitor skeleton created by dot2k Documentation/rv: Add deterministic automata instrumentation documentation Documentation/rv: Add deterministic automata monitor synthesis documentation tools/rv: Add dot2k Documentation/rv: Add deterministic automaton documentation tools/rv: Add dot2c Documentation/rv: Add a basic documentation rv/include: Add instrumentation helper functions rv/include: Add deterministic automata monitor definition via C macros ...
2022-07-18wifi: brcmsmac: fix repeated words in commentsJilin Yuan
Delete the redundant word 'the'. Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220709134207.30856-1-yuanjilin@cdjrlc.com
2022-07-15tracing/brcm: Use the new __vstring() helperSteven Rostedt (Google)
Instead of open coding a __dynamic_array() with a fixed length (which defeats the purpose of the dynamic array in the first place). Use the new __vstring() helper that will use a va_list and only write enough of the string into the ring buffer that is needed. Link: https://lkml.kernel.org/r/20220705224749.622796175@goodmis.org Cc: Arend van Spriel <aspriel@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Franky Lin <franky.lin@broadcom.com> Cc: Hante Meuleman <hante.meuleman@broadcom.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list.pdl@broadcom.com Cc: SHA-cyfmac-dev-list@infineon.com Cc: netdev@vger.kernel.org Acked-by: Kalle Valo <kvalo@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-07-15wifi: mac80211: change QoS settings API to take link into accountJohannes Berg
Take the link into account in the QoS settings (EDCA parameters) APIs. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-06-20wifi: mac80211: return a beacon for a specific linkShaul Triebitz
Pass the link id through to the get_beacon and return the beacon for a specific link id. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-06-20wifi: mac80211: split bss_info_changed methodJohannes Berg
Split the bss_info_changed method to vif_cfg_changed and link_info_changed, with the latter getting a link ID. Also change the 'changed' parameter to u64 already, we know we need that. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-06-20wifi: mac80211: move interface config to new structJohannes Berg
We'll use bss_conf for per-link configuration later, so move out all the non-link-specific data out into a new struct ieee80211_vif_cfg used in the vif. Some adjustments were done with the following spatch: @@ expression sdata; struct ieee80211_vif *vifp; identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator }; @@ ( -sdata->vif.bss_conf.var +sdata->vif.cfg.var | -vifp->bss_conf.var +vifp->cfg.var ) @bss_conf@ struct ieee80211_bss_conf *bss_conf; identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator }; @@ -bss_conf->var +vif_cfg->var (though more manual fixups were needed, e.g. replacing "vif_cfg->" by "vif->cfg." in many files.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-04-11mac80211: prepare sta handling for MLO supportSriram R
Currently in mac80211 each STA object is represented using sta_info datastructure with the associated STA specific information and drivers access ieee80211_sta part of it. With MLO (Multi Link Operation) support being added in 802.11be standard, though the association is logically with a single Multi Link capable STA, at the physical level communication can happen via different advertised links (uniquely identified by Channel, operating class, BSSID) and hence the need to handle multiple link STA parameters within a composite sta_info object called the MLD STA. The different link STA part of MLD STA are identified using the link address which can be same or different as the MLD STA address and unique link id based on the link vif. To support extension of such a model, the sta_info datastructure is modified to hold multiple link STA objects with link specific params currently within sta_info moved to this new structure. Similarly this is done for ieee80211_sta as well which will be accessed within mac80211 as well as by drivers, hence trivial driver changes are expected to support this. For current non MLO supported drivers, only one link STA is present and link information is accessed via 'deflink' member. For MLO drivers, we still need to define the APIs etc. to get the correct link ID and access the correct part of the station info. Currently in mac80211, all link STA info are accessed directly via deflink. These will be updated to access via link pointers indexed by link id with MLO support patches, with link id being 0 for non MLO supported cases. Except for couple of macro related changes, below spatch takes care of updating mac80211 and driver code to access to the link STA info via deflink. @ieee80211_sta@ struct ieee80211_sta *s; struct sta_info *si; identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr}; @@ ( s-> - var + deflink.var | si->sta. - var + deflink.var ) @sta_info@ struct sta_info *si; identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth}; @@ ( si-> - var + deflink.var ) Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com [remove MLO-drivers notes from commit message, not clear yet; run spatch] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-12-08brcmsmac: rework LED dependenciesArnd Bergmann
This is now the only driver that selects the LEDS_CLASS framework, which is normally user-selectable. While it doesn't strictly cause a bug, rework the Kconfig logic to be more consistent with what other drivers do, and only enable LED support in brcmsmac if the dependencies are all there, rather than using 'select' to enable what it needs. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211204173848.873293-2-arnd@kernel.org
2021-08-21brcmsmac: make array addr static const, makes object smallerColin Ian King
Don't populate the array addr on the stack but instead it static const. Makes the object code smaller by 79 bytes: Before: text data bss dec hex filename 176015 54652 128 230795 3858b .../broadcom/brcm80211/brcmsmac/main.o After: text data bss dec hex filename 175872 54716 128 230716 3853c .../broadcom/brcm80211/brcmsmac/main.o (gcc version 10.3.0) Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210819125552.8888-1-colin.king@canonical.com
2021-06-15brcmsmac: Remove the repeated declarationShaokun Zhang
Function 'brcms_c_stf_phy_txant_upd' are declared twice, remove the repeated declaration. Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1621844443-38290-1-git-send-email-zhangshaokun@hisilicon.com
2021-06-15brcmsmac: mac80211_if: Fix a resource leak in an error handling pathChristophe JAILLET
If 'brcms_attach()' fails, we must undo the previous 'ieee80211_alloc_hw()' as already done in the remove function. Fixes: 5b435de0d786 ("net: wireless: add brcm80211 drivers") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/8fbc171a1a493b38db5a6f0873c6021fca026a6c.1620852921.git.christophe.jaillet@wanadoo.fr
2021-06-15brcmsmac: Drop unnecessary NULL check after container_ofGuenter Roeck
The parameter passed to ai_detach() is guaranteed to never be NULL because it is checked by the caller. Consequently, the result of container_of() on it is also never NULL, and a NULL check on it is unnecessary. Even without that, the NULL check would still be unnecessary because the subsequent kfree() can handle NULL arguments. On top of all that, it is misleading to check the result of container_of() against NULL because the position of the contained element could change, which would make the check invalid. Remove it. This change was made automatically with the following Coccinelle script. @@ type t; identifier v; statement s; @@ <+... ( t v = container_of(...); | v = container_of(...); ) ... when != v - if (\( !v \| v == NULL \) ) s ...+> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210511235629.1686038-1-linux@roeck-us.net
2021-06-15brcmsmac: improve readability on addresses copyÍñigo Huguet
A static analyzer identified as a potential bug the copy of 12 bytes from a 6 bytes array to a 6 bytes array. Both arrays are 6 bytes addresses. Although not being a real bug, it is not immediately clear why is done this way: next 6 bytes address, contiguous to the first one, must also be copied to next contiguous 6 bytes address of the destination. Copying each one separately will make both static analyzers and reviewers happier. Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210511070257.7843-1-ihuguet@redhat.com
2021-03-17module: remove never implemented MODULE_SUPPORTED_DEVICELeon Romanovsky
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was implemented. We can safely remove it, because the kernel has grown to have many more reliable mechanisms to determine if device is supported or not. Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-02-11brcmsmac: Fix the spelling configation to configuration in the file d11.hBhaskar Chowdhury
s/configation/configuration/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210209232921.1255425-1-unixbhaskar@gmail.com
generated by cgit (git 2.34.1) at 2025-05-18 03:31:47 +0000