| Age | Commit message (Collapse) | Author |
|---|
|
kasprintf() can fail, we should check the return value.
Fixes: 5ed540aecc2a ("iwlwifi: use mac80211 throughput trigger")
Fixes: 8ca151b568b6 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some switch-cases were missing a fall through comment, so the compiler
may warn. Fix that by adding the comments where needed. In other
cases there was more text in the comment, which the compiler doesn't
recognize, so either remove the extra text or move it to a separate
comment line as appropriate.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).
To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.
Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it. But we will update
this firmware soon, so it won't be a problem anymore.
Fixes: 7089ae634c50 ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.
Fixes: 503ab8c56ca0 ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If the module parameter is set to disable the LED, we leave the
initialization routine before setting the LEDS_INIT_COMPLETE
status bit. Therefore, there's no need to check the parameter
again on exit, just the status check is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case an assert happens on init flow, the current
driver powers down the NIC, except if iwlmvm modparam
init_dbg=1, and only on very specific flows.
Extend this capability to cover most failure cases
by keeping track of what init configurations have been
completed. This way, we can allow NOT powering down
the NIC, while making sure that when the driver is
removed we don't try to free resources that haven't
been allocated. (This can result in a kernel panic.)
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
