| Age | Commit message (Collapse) | Author |
|---|
|
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308a4 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For 9000 devices withg upload, FW cannot send the entire phy
flags, and will send only the band - which is what we really
care about anyway. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently when configuring the cab queue the scheduler is configured
without station id - which results in station id 0.
In DQA mode this causes firmware to assert later on when the actual
station 0 is added with an empty tfd_queue_mask.
Fix that by configuring the queue to the broadcast station.
This is a bit trickier since the queue should not be included in the
tfd_queue_mask of the ADD_STA since it is a multicast queue, and the
tfd_queue_mask is only unicast queue. As a result the queue should be
enabled only after the broadcast station is added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In DQA mode the TXQs are allocated on demand, so make
sure the sniffer STA tfd_queue_msk isn't set.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need for the common MAC context function to have an
if on AP mode, the values can be overridden in the AP-specific
function later. Clean that up by adding the full command as a
new parameter to the AP-specific function, and doing it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
AP queue is properly released, but P2P queue isn't.
Fixes: commit 4c965139a3cd ("iwlwifi: mvm: support p2p device frames tx on dqa queue #2")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support sending P2P device frames should be sent from
queue #2, as required in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In DQA mode, allocate a dedicated queue (#9) for P2P GO/soft
AP probe responses.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Change the CMD queue to be queue #0 (rather than queue #9)
when working in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In DQA mode, allocate a dedicated queue (#3) for content
after beacon (AKA "CaB").
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.
Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.
There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.
This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.
When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.
When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When forming IBSS, mac80211 scans in order to find an already
existing cell to join.
In case the scan does not find any existing cell a new IBSS
cell is formed.
When receiving the beacons of another IBSS cell we should
merge if the other IBSS cell's TSF is higher than ours.
However, currently iwlmvm does not set any timestamp flag in
rx_status so there is no valid rx timestamp to compare the
beacon's TSF to.
The reason for that is that TSF as indicated by the firmware
is at INA time, but up till now mac80211 expected the TSF at
the beginning or end of the MPDU.
Set the flag to the newly added RX_FLAG_MACTIME_PLCP_START flag.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When in AP mode we need to filter in beacons from other APs to update HT
operation mode. As a power optimization the beacons are filtered out when
there are no associated stations. As a result, when there are no
associated stations, we will not update the HT operation mode until a
station connects.
Add a debugfs parameter that allows to disable this optimization.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The commit below called iwl_mvm_mac_ctxt_changed() to handle
a case that the vif is a P2P GO.
However iwl_mvm_mac_ctxt_cmd_go() ignores the number of
associated stations and asks the FW to pass beacons anyways.
Fix this by checking ap_assoc_sta_count parameter, in iwl_mvm_mac_ctxt_cmd_go()
as well, and ask the FW to pass beacons only when there's
at least one associated station.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The firmware knows better what antenna to choose.
Old firmware still need the setting, so use a flag to know
if the driver should choose the antenna or if the firmware
can do it iself.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Currently when creating a new vif in monitor mode the driver doesn't
allocate a specific station. This causes that in the situation that
tx traffic is injected, the tx queues are not scheduled,
with the result of a TFD queue hang.
Fix that by allocating a station and ensuring its tx queues
are scheduled.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=104591
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
