Age | Commit message (Collapse) | Author |
|
When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: fc36ffda3267 ("iwlwifi: mvm: support FTM initiator")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Till now, the driver asked the fw for a DTS measurement in automatic
mode. This triggered a flow in which the fw actively measured the
temperature. This is not needed anymore, as the fw performs
measurements by itself, without the driver triggering them, and the
current cadence in which the fw performs such measurements is
sufficient.
In addition, in some time-sensitive scenarios, in which the driver asks
the fw for an active measurement twice in a short time (<100ms), the fw
asserts with code 0x20100801.
Change the DTS measurement to _WITHOUT_MEASURE instead, so the fw will
respond with the last measurement it has performed.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The IGTK keys are only removed by mac80211 after it has already
removed the AP station. This causes the driver to throw an error
because mac80211 is trying to remove the IGTK when the station doesn't
exist anymore.
The firmware is aware that the station has been removed and can deal
with it the next time we try to add an IGTK for a station, so we
shouldn't try to remove the key if the station ID is
IWL_MVM_INVALID_STA. Do this by removing the check for mvm_sta before
calling iwl_mvm_send_sta_igtk() and check return from that function
gracefully if the station ID is invalid.
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use a unique name when registering a thermal zone. Otherwise, with
multiple NICS, we hit the following warning during the unregistration.
WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255
RIP: 0010:sysfs_remove_group+0x80/0x90
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0x5a/0x350
? sscanf+0x4e/0x70
device_unregister+0x1a/0x60
hwmon_device_unregister+0x4a/0xa0
thermal_remove_hwmon_sysfs+0x175/0x1d0
thermal_zone_device_unregister+0x188/0x1e0
iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm]
iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm]
_iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi]
iwl_opmode_deregister+0x90/0xa0 [iwlwifi]
__exit_compat+0x10/0x2c7 [iwlmvm]
__x64_sys_delete_module+0x13f/0x270
do_syscall_64+0x5a/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
|
|
Minor conflict in mlx5 because changes happened to code that has
moved meanwhile.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0df ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Cc: Alexander Lobakin <alobakin@dlink.ru>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831ac12356b695ff054bef641b9e99593:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873
https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831ac ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
CC: <stable@vger.kernel.org> # 5.3+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a straight-forward conversion case for the new function, and
while we're at it, we can remove a null write to skb->next by replacing
it with skb_mark_not_on_list.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add a new device table that contains information that can be checked
at runtime in order to decide which configuration to use. This allows
us to map the full cfg independently from the tran-specific
configuration.
This is the first step in creating the new table. Subsequent patches
will add the possibility of checking different values at runtime in
order to make the decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
With the new concept of separating the trans-specific (trans_cfg) data
from the rest of the cfg, we will start mapping only the trans_cfg
part to the PCI device ID/subsystem device ID. So we can assume that
the data passed to the probe function contains the trans_cfg, but
since the full cfg still contains the trans_cfg at the beginning, we
can allow a full cfg to be passed as well. This makes it easier to
convert the existing tables one by one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There are some unused register definitions, remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Print out the secure boot status, extended by the PCs of LMACs
and the UMAC. This needs to be before dumping, as dumping will
corrupt the PC (if the NMI is handled), so move that down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We have many different firmware images with the same version,
and it's sometimes cumbersome to figure out which image was
really used, especially as the marketing strings that we do
print out can be the same for (slightly) different hardware
using different firmware images.
Incorporate the firmware filename into the fw_version so it's
printed out all the time. Unfortunately, this will make the
string be longer than the 32 characters for ethtool, but we
almost never really use ethtool, so strip the "iwlwifi-"
prefix (if not overridden), and the remaining data that may
then be stripped at the end is not usually useful anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Now that we don't have dynamically changing domains anymore, we can
simply skip all the TLVs with domains that are not enabled. To do so,
remove the checks from the functions that handle the TLVs when a
timepoint is reached to the top allocation function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add new struct for SoSnj and add uhb support for ax411 structs.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We only call this function from a single place and it's very
very small and self-contained anyway, so remove the function and move
the code into the caller.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Now that we can't change the domain at runtime anymore, we don't have
to protect the active trigger status. Remove it. Additionally, we
don't need to flush the dumps at this point anymore, since this only
runs during initialization and there shouldn't be any dumps running.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't want to allow changing the domain via debugfs so that we can
apply the domain to all TLV types more easily (doing some at runtime
is difficult due to buffer allocations etc.). Change the
fw_dbg_domain debugfs file to be read-only and remove the write
function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The new API version adds support for FILS discovery frames.
It adds a new flag and a field for short SSID configuration.
The new API is backward compatible, so we can just switch to it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since v5.4-rc1 was released, iwlwifi started throwing errors when scan
commands were sent to the firmware with certain devices (depending on
the OTP burned in the device, which contains the list of available
channels). For instance:
iwlwifi 0000:00:14.3: FW error in SYNC CMD SCAN_CFG_CMD
This bug was reported in the ArchLinux bug tracker:
https://bugs.archlinux.org/task/64703
And also in a specific case in bugzilla, when the lar_disabled option
was set: https://bugzilla.kernel.org/show_bug.cgi?id=205193
Revert the commit that introduced this error, by using the number of
channels from the OTP instead of the number of channels that is
specified in the FW TLV that tells us how many channels it supports.
This reverts commit 06eb547c4ae4382e70d556ba213d13c95ca1801b.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Mehmet Akif Tasova <makiftasova@gmail.com>
[ Luca: reworded the commit message a bit. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the for loop where we are supposed to go through the entire table,
we are using a non-static local to keep the pos index. This makes
each iteration start with 3, so we always access the first item on the
table. Fix this by moving the variable outside of the loo so it
doesn't lose its value at every iteration.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: ba3224db7803 ("iwlwifi: mvm: fix an out-of-bound access")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is an old parameter that was used supposed to be used only when
LAR was still under development. It should not be used anymore, but,
since it's available, end-users have been mangling with it
unnecessarily. In some cases it can cause problems because when LAR
is supported the driver and the firmware do not expect it to be
disabled.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The driver is required to stop the debug monitor HW recording regardless
of the debug configuration since the driver is responsible to halt the
FW DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
L0S states have been found to be unstable with our devices and in
newer hardware they are not supported at all, so we must always set
the L0S_DISABLED bit. Previously we were only disabling L0S states if
L1 was supported, because the assumption was that transitions from L0S
to L1 state was the problematic case. But now we should never use
L0S, so do it regardless of whether L1 is supported or not.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This bit has been misnamed since the initial implementation of the
driver. The correct semantics is that setting this bit disables L0S
states, and we already clearly use it as such in the code. Rename it
to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b91 ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It used to be the case that if we got here, we wouldn't warn
but instead allocate the queue (DQA). With using the mac80211
TXQs model this changed, and we really have nothing to do with
the frame here anymore, hence the warning now.
However, clearly we missed in coding & review that this is now
a pure error path and leaks the SKB if we return 0 instead of
an indication that the SKB needs to be freed. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b91 ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A few configuration structures were either not referenced anymore or
assigned to devices IDs that were not in use anymore. Remove them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Validate that the queue ID is in range before trying to use it as
an index or for test_bit() - the previous bug showed that this has
in fact happened, and it was lucky that we caught it there, had the
bit been set then we'd have actually used the value despite being
far out of range.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we have only 2k RBs like on the latest (AX210) hardware, then
even on x86 where PAGE_SIZE is 4k we currently waste half of the
memory.
If this is the case, return partial pages from the allocator and
track the offset in each RBD (to be able to find the data in them
and remap them later.)
This might also address other platforms with larger PAGE_SIZE by
putting more RBs into a single large page.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't need to map *everything* of the RX buffers, we won't use
that much, map only the part we're going to use. This save some
IOMMU space (if applicable and it can deal with that) and also
prepares a bit for mapping partial pages for 2K buffers later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).
Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:
* 4096 for AX210 HE devices, which use 2k buffers by default,
* 2048 for 22000 family devices which use 4k buffers by default,
* 512 for existing 9000 family devices, which doesn't really
change anything since that's the default before this patch,
* 512 also for AX210/22000 family devices that don't do HE.
Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.
Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The new API requires the driver to config the supported frame format
(legacy, HT, VHT etc.).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The new API requires the driver to set the frame format
(legacy, HT, VHT etc.) to be used for the measurement.
The new API also supports 11az and secured measurement, but
these are not supported by the driver for now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
After more investigation on the hardware side, it appears that the
hardware bug regarding 2^32 boundary reaching/crossing also affects
other uses of the DMA engine, in particular the ones triggered by
the context-info (image loader) mechanism.
It also turns out that the bug only affects devices with gen2 TX
hardware engine, so we don't need to change context info for gen3.
The TX path workarounds are simpler to still keep for both though.
Add the workaround to that code as well; this is a lot simpler as
we have just a single way to allocate DMA memory there.
I made the algorithm recursive (with a small limit) since it's
actually (almost) impossible to hit this today - dma_alloc_coherent
is currently documented to always return 32-bit addressable memory
regardless of the DMA mask for it, and so we could only get REALLY
unlucky to get the very last page in that area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When receiving a new MCC driver get all the data about the new country
code and its regulatory information.
Mistakenly, we ignored the cap field, which includes global regulatory
information which should be applies to every channel.
Fix it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we have offloaded rate scaling, which is always true for those
devices supporting HE, then report the TX rate directly from the
data the firmware gives us, instead of only passing it to mac80211
on frame status only and for it to track it.
First of all, this makes us always report the last good rate that
the rate scaling algorithm picked, which is better than reporting
the last rate for any frame since management frames etc. are sent
with very low rates and could interfere.
Additionally, this allows us to properly report HE rates, though
in case there's a lot of trigger-based traffic, we don't get any
choice in the rates and don't report that properly right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We had a check on !NVM_EXT and then a check for NVM_SDP in the else
block of this if. The else block, obviously, could only be reached if
using NVM_EXT, so it would never be NVM_SDP.
Fix that by checking whether the nvm_type is IWL_NVM instead of
checking for !IWL_NVM_EXT to solve this issue.
Reported-by: Stefan Sperling <stsp@stsp.name>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the allocation loop, "pages" will never become zero (because of the
DIV_ROUND_UP), so if we can't allocate any size and pages becomes 1,
we will keep trying to allocate 1 page until it succeeds. And in that
case, as coverity reported, block will never be NULL.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1487402 ("Control flow issues")
Fixes: 14124b25780d ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 14124b25780d ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Warn if the DMA bug is going to happen. We don't have a good
way of actually aborting in this case and we have workarounds
in place for the cases where it happens, but in order to not
be surprised add a safety-check and warn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's a hardware bug in the flow handler (DMA engine), if the
address + len of some TB wraps around a 2^32 boundary, the carry
bit is then carried over into the next TB.
Work around this by copying the data to a new page when we find
this situation, and then copy it in a way that we cannot hit the
very end of the page.
To be able to free the new page again later we need to chain it
to the TSO page, use the last pointer there to make sure we can
never use the page fully for DMA, and thus cannot cause the same
overflow situation on this page.
This leaves a few potential places (where we didn't observe the
problem) unaddressed:
* The second TB could reach or cross the end of a page (and thus
2^32) due to the way we allocate the dev_cmd for the header
* For host commands, a similar thing could happen since they're
just kmalloc().
We'll address these in further commits.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The fw already support scan api v12,
v11 is not needed anymore.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Before we start looping over the internal TX FIFOs increase the fifo
number, but that's incorrect and causes a FIFO to be skipped. This is
probably due to a copy and paste from the previous loop.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This fixes a long-standing bug - we haven't been able to check the
firmware image that was loaded for D3/not-D3 since the introduction
of the unified image...
Fix this by keeping a status flag for D3 instead of checking for
the firmware image that's loaded.
This reduces occurrences of checks for IWL_UCODE_WOWLAN to just the
code that actually loads the image or deals with it in other ways.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|