| Age | Commit message (Collapse) | Author |
|---|
|
Add a000 family configuration to iwl-cfg struct
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Reserve a single iwl_fw_error_dump_type enum for external
code utilities.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add support of dumping new RFH instead of FH registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
gcc-6 reports the following error if -Werror=unused-const-variable
is enabled.
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:210:21: error:
'iwlagn_loose_lookup' defined but not used
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430f0b3 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data. This is
unnecessary, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add 6 new 8265 series PCI IDs:
- (0x24FD, 0x1130)
- (0x24FD, 0x0130)
- (0x24FD, 0x0910)
- (0x24FD, 0x0930)
- (0x24FD, 0x0950)
- (0x24FD, 0x0850)
CC: <stable@vger.kernel.org> [4.6+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add 3 new 8260 series PCI IDs:
- (0x24F3, 0x10B0)
- (0x24F3, 0xD0B0)
- (0x24F3, 0xB0B0)
CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.
This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211(). Fortunately, it's
never used so we can just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently code calls restock for mq devices during the init
function, unlike sq where restock is called after init.
This causes an harmless but alarming deadlock warning from
lockdep, to fix this - unify the init code.
Rename the restock functions while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.
This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Instead of explicitly indicating the difference between just
DVM and MVM with an mvm_fw boolean change this to fw.type to
be more extensible and easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since the values of this enum are used only internally,
we can let the compiler number them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* More work on the RX path for the 9000 device series
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
|
|
For some reason, the FRAME_RELEASE message handling for the
default queue ended up being in the only/default queue for
non-RSS devices; fix that and handle FRAME_RELEASE properly
on the default queue for RSS devices.
Fixes: 585a6fccf5b8 ("iwlwifi: mvm: infrastructure for frame-release message")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add a warning in case packet didn't end up in the HW
destined queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We now have 9000 devices that support multiple frames in
a single RB. Enable it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For 9000 devices we can have PCIe bus for discrete
devices and IOSF bus for integrated devices.
PCIe supports maximum transfer size of 128B while IOSF
bus supports maximum transfer size of 64B.
Configure RB size accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support queue removal in DQA mode in iwl_mvm_rm_sta() also when
the device isn't a STA connected to an AP.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Somehow we ended up without leading spaces here, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The new hardware that supports multiple queue also
de-aggregates A-MSDUs. This means that we can advertise
the maximal size of A-MSDUs regardless of the receive
buffer's size.
In order to be able to forcefully use a lower A-MSDU size,
add a default value for the module parameter. Pre-9000
will have a default of 4K, and 9000 will have 12K.
Setting the amsdu_size module parameter to 4K will limit
the A-MSDU on 9000 as well.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modern C standards expect the 'inline' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4096:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
gcc-6 warns about code in il3945_hw_txq_ctx_free() being
somewhat ambiguous:
drivers/net/wireless/intel/iwlegacy/3945.c:1022:5: warning: suggest explicit braces to avoid ambiguous 'else' [-Wparentheses]
This adds a set of curly braces to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
My cleanup in "iwlwifi: prepare for higher API/CAPA bits" accidentally
inverted a few tests - fix them.
Fixes: 859d914c8f5c ("iwlwifi: prepare for higher API/CAPA bits")
Reported-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The FW expect the driver to set the encryption algorithm type when
installing the IGTK key in the HW.
Currently when installing CMAC IGTK key we don't set the algorithm type
and as a result the FW fails to calculate the MIC of multicast management
frames.
Fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We try to access sta before we check for IS_ERR_OR_NULL(), so we may
end up accessing a NULL pointer. To prevent that, move the conversion
from sta to mvm_sta below the check.
Fixes: b915c10174fb ("iwlwifi: mvm: add reorder buffer per queue")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The commit below mistakenly changed an rcu_dereference_check
to a rcu_dereference_protected which introduced the
following RCU warning:
[ INFO: suspicious RCU usage. ]
4.6.0-rc7-next-20160513-dbg-00004-g8de8b92-dirty #655 Not tainted
-------------------------------
drivers/net/wireless/intel/iwlwifi/mvm/mvm.h:1069 suspicious rcu_dereference_protected() usage!
Call Trace:
[<ffffffff8106b836>] lockdep_rcu_suspicious+0xf7/0x100
[<ffffffffa03b2321>] iwl_mvm_get_key_sta.part.0+0x5d/0x80 [iwlmvm]
[<ffffffffa03b4acb>] iwl_mvm_update_tkip_key+0xd3/0x162 [iwlmvm]
[<ffffffffa03a2b60>] iwl_mvm_mac_update_tkip_key+0x17/0x19 [iwlmvm]
[<ffffffffa0329646>] ieee80211_tkip_decrypt_data+0x22c/0x24b [mac80211]
[<ffffffffa0318bb1>] ieee80211_crypto_tkip_decrypt+0xc5/0x110 [mac80211]
[<ffffffffa033102e>] ieee80211_rx_handlers+0x9bb/0x1fe1 [mac80211]
Fixes: 13303c0fb148 ("iwlwifi: mvm: use helpers to get iwl_mvm_sta")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The 16 seconds timeout we were using turned out to be too short.
Recalculations by system show that the total time in both bands should
be < 18.5 seconds, even in the slowest cases (e.g. DCM P2P with
DTIM=2). Rounding it up to 20 seconds for a bit more safety.
Fixes: 728e825f81b1 ("iwlwifi: mvm: add a scan timeout for regular scans")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with
removing debugfs files should be fixed thanks to the great work of
Nicolai Stange. We also have some isa updates in here (the x86
maintainers told me to take it through this tree), a new warning when
we run out of dynamic char major numbers, and a few other assorted
changes, details in the shortlog.
All have been in linux-next for some time with no reported issues"
* tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
Revert "base: dd: don't remove driver_data in -EPROBE_DEFER case"
gpio: ws16c48: Utilize the ISA bus driver
gpio: 104-idio-16: Utilize the ISA bus driver
gpio: 104-idi-48: Utilize the ISA bus driver
gpio: 104-dio-48e: Utilize the ISA bus driver
watchdog: ebc-c384_wdt: Utilize the ISA bus driver
iio: stx104: Utilize the module_isa_driver and max_num_isa_dev macros
iio: stx104: Add X86 dependency to STX104 Kconfig option
Documentation: Add ISA bus driver documentation
isa: Implement the max_num_isa_dev macro
isa: Implement the module_isa_driver macro
pnp: pnpbios: Add explicit X86_32 dependency to PNPBIOS
isa: Decouple X86_32 dependency from the ISA Kconfig option
driver-core: use 'dev' argument in dev_dbg_ratelimited stub
base: dd: don't remove driver_data in -EPROBE_DEFER case
kernfs: Move faulting copy_user operations outside of the mutex
devcoredump: add scatterlist support
debugfs: unproxify files created through debugfs_create_u32_array()
debugfs: unproxify files created through debugfs_create_blob()
debugfs: unproxify files created through debugfs_create_bool()
...
|
