Age | Commit message (Collapse) | Author |
|
RX full flags are raised if certain types of RX FIFO are full, and then
drop all following MPDU of AMPDU. In order to resume to receive MPDU
when RX FIFO becomes available, we clear the register bits by the
commit a0d99ebb3ecd ("wifi: rtw89: initialize DMA of CMAC"). But, 8852AE
needs more settings to support this. To quickly fix disconnection problem,
revert the behavior as before.
Fixes: a0d99ebb3ecd ("wifi: rtw89: initialize DMA of CMAC")
Reported-by: Damian B <bronecki.damian@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217710
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Damian B <bronecki.damian@gmail.com>
Link: https://lore.kernel.org/r/20230808005426.5327-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If there is a failure during rtw89_fw_h2c_raw() rtw89_debug_priv_send_h2c
should return negative error code instead of a positive value count.
Fix this bug by returning correct error code.
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/tencent_AD09A61BC4DA92AD1EB0790F5C850E544D07@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A firmware contains basic header, sections and optional dynamic header.
Define them by a struct, so it will be easier to understand the layout,
and also simply access these elements.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616060601.28460-1-pkshih@realtek.com
|
|
Some old declarations about TX power stuffs were named with confusing
`_max`. But, they mean "the number of". So we change them to be named
with `_num`.
(No logic is changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616060523.28396-1-pkshih@realtek.com
|
|
RTL8851B is a chip with only single RF path, and it must use 1 TX power
value for transmission, so force 1 TX power value to prevent hardware
logic gets wrong TX power values randomly in certain samples.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-6-pkshih@realtek.com
|
|
The main change is to adjust RX calibration groups from {0,1,2,3} to {0,2}
in 5 GHz, so reduce elements from 4 to 2, and use index to iterate them.
Meanwhile, always do RX narrowband calibration (ID_NBRXK) for each group.
NCTL is used to assist IQK, so also update NCTL to 0x6 along with internal
tag HALRF_029_00_103.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-5-pkshih@realtek.com
|
|
LCK is short for LC Tank calibration. To keep RF performance, do this
calibration if difference of thermal value is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-4-pkshih@realtek.com
|
|
Update 8851B TX power tables to RF version R28.
TX power tables' changes:
* TX power limit and TX power shape:
update 5 GHz configurations for FCC and IC
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-3-pkshih@realtek.com
|
|
Update 8851b radio A parameters to R28 along with internal HALRF_029_00_103
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-2-pkshih@realtek.com
|
|
Fix spelling typo of IQK debug messages.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-3-dmantipov@yandex.ru
|
|
Drop useless '_iqk_track()' and 'rtw8852a_iqk_track()' (they
just change 'thermal_rek_en' field which is set but unused
and so removed as well) functions, set but unused 'kcount'
field of 'struct rtw89_iqk_info', and convert 'thermal' to
local variables where appropriate (it doesn't need to have
longer storage duration because it is actually used for the
debugging purposes only).
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-2-dmantipov@yandex.ru
|
|
Remove a bunch of unused (and set but unused) fields
from 'struct rtw89_btc_wl_nhm', 'struct rtw89_dle_info',
'struct rtw89_hal' and 'struct rtw89_env_monitor_info'
driver-specific data structures, adjust related bits.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-1-dmantipov@yandex.ru
|
|
Update 8852c radio A/B parameters from internal HALRF_029_00_102 R63.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-9-pkshih@realtek.com
|
|
Update TX power tables to RF version R63.
TX power tables' changes:
* TX power byrate:
tweak a bit
* TX power limit, TX power limit RU, TX power shape:
configure values for MEXICO, UKRAINE, CHILE, QATAR
tweak a bit on other configured values
* 6 GHz TX power limit, 6 GHz TX power limit RU:
add an extra dimension for 6 GHz regulatory power type, i.e.
STD (standard power), LPI (low power indoor), VLP (very low power)
Besides, we adjust TX power handling at 6 GHz in phy to consider 6 GHz
regulatory power type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-8-pkshih@realtek.com
|
|
Update TX power tables to RF version R63.
TX power tables' changes:
* TX power byrate:
tweak a bit
* TX power limit, TX power limit RU, TX power shape:
configure values for MEXICO, UKRAINE, CHILE, QATAR
tweak a bit on other configured values
* 6 GHz TX power limit, 6 GHz TX power limit RU:
add an extra dimension for 6 GHz regulatory power type, i.e.
STD (standard power), LPI (low power indoor), VLP (very low power)
Besides, we adjust TX power handling at 6 GHz in phy to consider 6 GHz
regulatory power type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-7-pkshih@realtek.com
|
|
Update TX power tables to RF version R63.
TX power tables' changes:
* TX power byrate:
tweak a bit
* TX power limit, TX power limit RU, TX power shape:
configure values for MEXICO, UKRAINE, CHILE, QATAR
tweak a bit on other configured values
* 6 GHz TX power limit, 6 GHz TX power limit RU:
add an extra dimension for 6 GHz regulatory power type, i.e.
STD (standard power), LPI (low power indoor), VLP (very low power)
Besides, we adjust TX power handling at 6 GHz in phy to consider 6 GHz
regulatory power type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-6-pkshih@realtek.com
|
|
Configure the corresponding power type for 6 GHz regulatory if we can
determine one single target. Otherwise, we use the default one.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-5-pkshih@realtek.com
|
|
Update notes:
According to Realtek Regulatory R40 and Realtek Channel Plan R64,
configure rtw89_regulatory mapping of 6 GHz for more countries and
adjust rtw89_regulatory mapping of 2/5 GHz for a few countries.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-4-pkshih@realtek.com
|
|
We allow platform to disable 6 GHz on chips, which supports 6 GHz, through
BIOS. Driver will evaluate Realtek acpi DSM with RTW89_ACPI_DSM_FUNC_6G_DIS
(function 3) to get whether 6 GHz should be disabled.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-3-pkshih@realtek.com
|
|
We refine to check if supported bands of NL80211_BAND_2GHZ and
NL80211_BAND_5GHZ exist before freeing their iftype_data. For
now, it does not really encounter problems because all current
chips support both 2 GHz and 5 GHz. But, driver actually allows
chips to declare whether 2/5 GHz are supported or not. In case
some future chips really don't support them, we refine this code.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-2-pkshih@realtek.com
|
|
RTL8851B firmware supports CRASH_TRIGGER feature from v0.29.41.0.
After this is configured, debugfs fw_crash can support type 1 on
RTL8851B to trigger firmware crash and verify L2 recovery through
simulation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-5-pkshih@realtek.com
|
|
The key condition to check in wrapper of setting TX power is whether entity
is active or not. Before entity is active, we restrict TX power from being
set by outside callers, e.g. SAR/regulatory.
We mark entity as inactive when powering off MAC. Then, we will mark it as
active when we initialize HW channel stuffs after MAC power on. Although we
can get an active entity after leaving idle phase, TX power doesn't be set
well for default channel until stack set target channel for connection. It
causes that RF things cannot use better TX power during this interval.
Below are some cases which may encounter this or a similar situation.
* hw scan process before connection
As described above.
* right after restart hardware process (SER L2)
HW stuffs of target channel is initialized after mac80211 restart
hardware, but we unexpectedly need to wait one more command to set
channel again or to set TX power.
To fix it and improve RF behavior in that interval, during setting channel,
we don't need to check entity state before setting TX power, which actually
is used to restrict outside callers. It means we call chip ops directly to
replace the wrapper call. Then, TX power can be initialized as long as we
initialize/setup HW stuffs on one channel.
Besides, all chips should configure ops of setting TX power, so we remove
trivial check on pointer.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-4-pkshih@realtek.com
|
|
We now support RTL8851B which has only single RF path. For chip with
single RF path, TX power page is valid only in single path section.
So, we refine debugfs txpwr table to access TX power page according
to RF path number of runtime chip. It can prevent us from reading
beyond valid sections.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-3-pkshih@realtek.com
|
|
This enables hw_scan for 8851b after firmware version 0.29.37.1.
Extend the channel info struct with padding zeros so newer firmware
can work properly, this change is backward compatible with older
firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-2-pkshih@realtek.com
|
|
There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Originally, add this check rule to prevent entering LPS if more than one
vif (in station mode) connect to AP. Since we have checked this by previous
commit, remove this redundant check.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-4-pkshih@realtek.com
|
|
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b5d ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. For now, it is allowed to enter PS only if
single one station vif is working, and it could possible to have PS per
vif after firmware can support it. Without this fix, driver doesn't
enter PS anymore that causes higher power consumption.
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-3-pkshih@realtek.com
|
|
struct rtw89_btc_btf_tlv contains a one-byte member that is intended as a
flexible array:
In function 'fortify_memcpy_chk',
inlined from '_append_tdma' at drivers/net/wireless/realtek/rtw89/coex.c:1579:3:
include/linux/fortify-string.h:583:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
583 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Make this actually use a flexible array to let the compiler understand.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230523113241.2772811-1-arnd@kernel.org
|
|
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522085924.913649-1-colin.i.king@gmail.com
|
|
The register-based H2C/C2H are used to exchange commands and events with
firmware. The exchange data is limited, but it is relatively simple,
because it can work before HCI initialization. To make these code clean,
use struct to access them. This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-6-pkshih@realtek.com
|
|
RX descriptor is to provide basic and important information related to
packets, such as packet size, security, MAC ID and so on. Change to use
struct to access these fields, and not change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-5-pkshih@realtek.com
|
|
PHY status IEs generated by BB hardware is to provide more detail
information related to received packets, such as RSSI and bandwidth.
To avoid type casting, change buf type from u8* to void* as well.
This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-4-pkshih@realtek.com
|
|
If received packet type is PPDU status, RX info provides information
attached by MAC hardware, and mention how long BB information attached.
This conversion patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-3-pkshih@realtek.com
|
|
newer chips
The next generation chips use different RX descriptor format, so add
a chip_ops to hook suitable handlers. Also, the length of RX descriptor is
different, so add a variable to store the length according to chip and
descriptor content dynamically. Then, the code can be more general.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-2-pkshih@realtek.com
|
|
Since 8851BE is ready, so add 8851BE to Makefile and Kconfig. Currently,
it can support STA, AP and monitor modes with good performance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-8-pkshih@realtek.com
|
|
8851B has the same issue: management frames get stuck when WiFi
chip enters low PS mode, so we also add notify wake function to
trigger WiFi chip wake before forwarding management frames.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-7-pkshih@realtek.com
|
|
The register ranges of upcoming chips are different from current, and even
existing chips have different ranges, so support longer length to dump
registers. Then, user space can decide the ranges according to chip.
Since arbitrary length (e.g. 7) would be a little complicated, so simply
make length a multiple of 16. The output looks like
18620000h : 8580801f 82828282 82828282 080800fd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-6-pkshih@realtek.com
|
|
RF configurations include RF calibrations and getting thermal value.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-5-pkshih@realtek.com
|
|
These configurations include path control, TX grant, TX scheduler,
register-based H2C/C2H and so on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-4-pkshih@realtek.com
|
|
These capabilities include helpers of BT coexistence, RX PPDU status
parser, DIG (dynamic initial gain) and CFO (center frequency offset)
settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-3-pkshih@realtek.com
|
|
Get TX power value from tables according to selected country and channel,
and set proper power to registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-2-pkshih@realtek.com
|
|
H2C of packet offload needs to wait FW ACK by C2H. But, it's possible
that packet offload happens during SER (system error recovery), e.g.
SER L2 which restarts HW. More, packet offload flow isn't deferrable.
So, the H2C wait may get `ret == 1` (unreachable).
However, the logic FW deals with packet offload is simple enough, just
clone content. It means that as long as the H2C is issued successfully,
the thing will succeed sooner or later. Therefore, after we add a debug
log when receiving ACK to packet offload, it would be acceptable that
during SER, packet offload don't really wait for ACK. And, if debugging,
we can still check its debug logs. Besides, we can expect that if we see
SER before receiving ACK to packet offload, those debug logs of the ACK
have a time difference.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-4-pkshih@realtek.com
|
|
Some specific H2C (host to chip command) needs waiting until FW ACK by
C2H (chip to host event). However, during SER (system error recovery),
most interrupts are disabled, so we can't receive C2H immediately. It
causes this kind of H2C TX waits will always time out during SER.
To save time spent by SER, we don't do these redundant waits. And, to
make a difference from -ETIMEDOUT in other cases, we make the function
return 1 for SER case. When some H2C callers really catch `ret == 1` at
runtime, they can determine whether it's reasonable or not, and consider
how to resolve their flow if needed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-3-pkshih@realtek.com
|
|
The total_sta_assoc and the tdls_peer are used for statistics accodring
to stations' information. L2 (Level 2) SER (system error recovery) will
call ieee80211_restart_hw() which re-invokes sta_state ops. And then,
the total_sta_assoc and tdls_peer will be re-increased. In case wrong
statistics results, we reset them in SER L2 handling.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-2-pkshih@realtek.com
|
|
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com
|
|
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com
|
|
RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-2-pkshih@realtek.com
|
|
Parse efuse content to recognize MAC address, RFE type, XTAL offset and
so on. And, parse offset of PHY capability to retrieve TX power
calibration data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-7-pkshih@realtek.com
|
|
Set MAC/BB/RF registers according to channel we are going to set. In
additional, certain channels or bands need more deals, such as enable CCK
in 2 GHz band, spur elimination at certain frequencies.
The set channel helper is used to save/restore states before/after setting
channel, and does reset BB to prevent hardware getting stuck in abnormal
state during switching channel and receiving data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-6-pkshih@realtek.com
|
|
Add basic functions to power on chip and enable and access BB/RF, as
well as reset and hardware settings of BB.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-5-pkshih@realtek.com
|